Metallurgy Commons^™

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam

Materials Science and Engineering Faculty Research & Creative Works

Modern aerostructures, including wings and fuselages, increasingly feature sandwich structures due to their high-energy absorption, low weight, and high flexural stiffness. The face sheet of these sandwich structures are typically thin composite laminates with interior honeycombs made of Nomex or aluminum. Standard cores are structurally efficient, but their design cannot be varied throughout the structure. With additive manufacturing (AM) technology, these core geometries can be altered to meet the design requirements that are not met in standard honeycomb cores. This study used a modified aluminum honeycomb core, with increased surface area on the top and bottom, as the core material …

Recycling Metal Chips Into Usable Materials, Alex Mortensen, Ben Mortensen

Williams Honors College, Honors Research Projects

This report entails the scope, design considerations, and plans for creating a metal chip converter into metal briquettes. The construction is a set of machines with multiple processes to make the conversion happen. The process includes washing fine metal chips, drying them off, compressing them, and melting them down into usable briquettes. This project is intended to make a simple process to recycle metal chips into usable material for reuse. The project's objective is to reduce the costs of storage and recycling waste by offering a solution to recycle it into materials the shop can reuse.

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Investigation Of Oxidation And Corrosion Resistance Of Ni-Based Alloys And Stainless Steels Under Co2 Environments At Elevated Temperatures, Spencer Roy Fultineer

Graduate Theses, Dissertations, and Problem Reports (ETD)

High mechanical strength integrity, high robustness towards oxidation, and high resistance to carburization under CO2 environments at elevated temperatures are usually required for metallic systems that are employed for power generation. INCONEL 625 is a nickel-based superalloy that started development in the 1950s. This material was designed with the distinct purpose of use in high-temperature and high-pressure systems. While various materials possess the physical properties to handle these conditions, the creation of IN625 addresses the need for a material to withstand the highly corrosive properties of these kinds of environments. In order to evaluate the oxidation and corrosion resistance of …

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo

Journal of Materials Exploration and Findings

Mubadala Petroleum operates offshore platforms in a southern Makassar Straits that needs to be periodically inspected. The cost for the inspection is massive due to the high cost of mobilization and demobilization of vessels including crew and equipment. In response of a new approach to reduce cost, a Risk-Based Underwater Inspection (RBUI) methodology is developed. This RBUI purpose is to reduce the inspection interval of the offshore platform, from every 2 years to a longer period^[1]. There are existing RBUI methodologies, which are already developed and implemented in other companies^[5]. Purpose of this paper is to …

A Constitutive Material Model For Simulating Texture Evolution And Anisotropy Effects In Cold Spray., Creston Michael Giles

Theses and Dissertations

Cold spray has seen rapid advancement since its inception and has shown significant potential as a method of additive manufacturing. However, the large plastic deformation and repeated heating/cooling cycles that the material undergoes during the cold spray process can result in gradients in material structure and large residual stresses. The purpose of this study is to extend the existing EMMI material model to include anisotropic material response through the use of orientation distribution functions to predict residual stresses and anisotropy resulting from cold spray and similar additive manufacturing processes. Through the use of a finite element simulation, yield surfaces for …

Platinum-Iridium Alloys In Jewelry, Nathen C. Christa, Seth Walker, Dylan Hallman

ME 4133/6133 Mechanical Metallurgy

One of the most widely used metals on the periodic table is Platinum (Pt). The name is derived from the Spanish Platina, meaning “silver.” This malleable, ductile material is widely used in applications due to its unique chemical properties. A couple of these unique properties include a high melting point and good resistance to corrosion or chemical attack. Platinum materials have alloys that are indispensable in the chemical laboratory for electrodes. This allows for material applications in crucibles and dishes to withstand elevated temperatures. Platinum is used primarily in catalytic converters in vehicles converting emissions from the vehicle’s engine into …

High-Carbon Steel In Additive Manufacturing, Chidi N. Agusiegbe, Devin Morton, Emmanuel Moore

ME 4133/6133 Mechanical Metallurgy

High-carbon steel can be processed through numerous methods. The method that will be focused on primarily is processing high-carbon steel through means of additive manufacturing. Additive manufacturing is the industrial production name for 3D printing, a computer-controlled process that creates three-dimensional objects by depositing materials, usually in layers. AM methods like wire laser additive manufacturing (WLAM) and electron beam melting (EBM) are all common methods for fabricating high carbon steel. The perks associated with these methods are that they improve some drawbacks of the natural properties of high-carbon steel. This paper discusses the uses of these additive manufacturing methods along …

High Carbon Steel In Additive Manufacturing, Emmanuel Moore Ii, Devin Morton, Chid Agusiegbe

ME 4133/6133 Mechanical Metallurgy

The first known use of carbon steel dates back to 500 A.D. when a blacksmith mistakenly used iron ore as a primary material for smithing. This material, as the name suggests, is made up of both carbon and iron. This material, as one of the most abundant at the time, was used most frequently in European and Asian countries. “Carbon steel first appeared around the year 500 AD in Damascus steel swords as well as Japanese swords. They were prized for their sharp edges and sturdiness compared to other weapons of the era. The composition of these swords was very …

Integration Of Hadfield Steel Into Modern Body Armor, Jason T. Fridlund

ME 4133/6133 Mechanical Metallurgy

The increased lethality of recently fielded projectiles mandates a proportional escalation in armor performance. Recent advancements in ceramic technologies have allowed designers to incorporate harder but more brittle materials into hard armor designs to defeat yet more capable penetrating projectiles. Ceramics suffer from the feature of shattering, however, even when impacted by threats below their design parameters. While this shattering mechanism is used effectively to dissipate energy from high-energy rifle projectiles, it is wasted on low-energy projectiles, and can result in easily damaged lifesaving gear, both of which are undesirable in combat. In contrast, steel body armor has been used …

High Carbon Steel In Additive Manufacturing, Chidi Agusiegbe, Devin Morton, Emmanuel Moore

ME 4133/6133 Mechanical Metallurgy

Infographic demonstrating the composition, and use of high carbon steels as well as the process of the material in additive manufacturing.

Sae 8620 Pspp Map - Infographic, John F. Mitchener

ME 4133/6133 Mechanical Metallurgy

This infographic summarizes a Processing-Structure-Property-Performance (PSPP) Map for SAE 8620 alloy steel, with an emphasis on the gas carburization process. This PSPP map allows researchers and material scientists to better understand the processes that drive the microstructures, material properties, and ultimate performance parameters.

Characterization Of Materials Properties In Additively Manufactured Aisi-420 Martensitic Steel Deposited By Laser Engineered Net Shaping, Md Mehadi Hassan

Nanoscience and Microsystems ETDs

Metal additive manufacturing (AM) is a disruptive technology enabling the fabrication of complex and near-net-shaped parts by adding material layer-wise. It offers reduced lead production time. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical, and mold tooling. Despite the tremendous advantages of AM, some challenges still prevent this technology's adoption in high-standard applications. Anisotropy and inhomogeneity in the mechanical properties of the as-built parts and the existence of pores and lack-of-fusion defects are considered the main issues in directed energy deposition (L-DED) parts. Laser-engineered net shaping LENS® offers excellent possibilities to fabricate metal tools …

Evaluation Of Material Request Order To Support Sustainable Construction, Fajar Susilowati, Nur Nahdiah Anggraeni

Makara Journal of Technology

This study was conducted on one of Indonesia’s apartment projects, in which reinforced concrete is the main structure. Based on existing project data, this project experienced a decline in the construction work’s progress, thus reducing the project’s overall progress. This decline occurred because the delivery of concrete reinforcement material was delayed. This study aimed to determine the process of material request order and its relationship with the work implementation, as well as the factors that influenced the delayed arrival of concrete reinforcement material at the project site. The method used in this study was observation and interview. Data were analyzed …

Ferrous Alloy Manufacturing For The Martian Surface Through In-Situ Resource Utilization With Ionic Liquids Harvested Iron And Bosch Process Carbon, Blake C. Stewart

Theses and Dissertations

As research continues for the habitation of the Lunar and Martian surfaces, the need for materials for construction of structural parts, mechanical components, and tools remains as a major milestone. The use of in-situ resource utilization (ISRU) techniques is critical due to the financial, physical, and logistical burdens of sending supplies beyond low-Earth orbit. The Bosch process is currently in development as a life support system at the National Aeronautics and Space Administration’s (NASA) Marshall Space Flight Center (MSFC) to regenerate oxygen (O2) from metabolic carbon dioxide (CO2) with the byproduct of elemental carbon (C). The Bosch process presents a …

Creep Behavior Of A Ti-Based Multi-Principal Element Alloy, Benjamin Elbrecht

All Theses

Abstract

The understanding of microstructural damage mechanisms is the foundation of better understanding existing materials and future material development. There are significant challenges to measuring these damage mechanisms in-situ as continuous observation of the state of the microstructure is difficult or impossible for many experimental setups. This thesis presents a method for measuring grain boundary sliding (GBS) and local strain concentrations in-situ via a Heaviside function based algorithm. GBS is the shearing of two grains along their shared grain boundary and is a common damage mechanism in creep which presents as a discontinuity that can be measured with a Heaviside …

Effect Of Dispersions Of Al2o3 On The Physical And Mechanical Properties Of Pure Copper And Copper-Nickel Alloy, Samah El-Khatib, A. H. Elsayed, A. Y. Shash, A. El-Habak

Future Engineering Journal

This paper illustrates the mechanical and physical properties of pure Cu and Cu-Ni (50-50 wt. %) alloy mixed with Al₂O₃ (1-4 wt. %) as micro-particles reinforcement materials. The attained composite alloy specimens' characteristics were estimated such as microstructure, relative density, electrical and thermal conductivity, hardness, and compression yield stress properties to adjust the suitable optimum percentage of reinforcing material which has the best physical and mechanical properties with different main matrix materials whether pure Cu powder or Cu-Ni mechanical alloy. The micron-sized Al₂O₃ was added to enhance the mechanical and physical properties of the …

Properties Of 25cr7ni Stainless Steel Fabricated Through Laser-Powder Bed Fusion., Arulselvan Arumugham Akilan

Electronic Theses and Dissertations

Stainless steel is a low carbon high alloyed system with higher concentrations of Cr& Ni, which impart high corrosion resistance to them. Alloys with approximately 25% Cr & 7% Ni in their chemical composition are commercially referred to as ‘Super Duplex Stainless Steel’. They have a unique phase composition of approximately 50% ferrite & 50% austenite, yielding a robust combination of high mechanical strength & corrosion resistance. They find extensive interest & application in the fields which demand a longer service life under intense mechanical / corrosive environment such as offshore oil rigs & pipelines in nuclear power plants. Traditional …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Induction Brazing, Austin Squire, Scott Compton, Logan Hathaway, Michael Fleming

Williams Honors College, Honors Research Projects

Our team would like to research and explore ways of designing a portable device that uses induction heating/brazing to connect two exhaust pipes together.

Effects Of Titanium And Cerium Addition On Grain Size And Mechanical Properties Of Ductile Iron Castings, Shelton F. Fowler Iv

College of Graduate Studies: Theses & Dissertations

According to the Hall-Petch equation, the refinement of grains in metals increases the yield strength of the material. Austenite grain size influences the fineness of microstructural constituents in the ferrous alloys. It is well studied that cerium and titanium refine the austenite in steels and some gray irons, but no studies have been done to systematically explore the effects of cerium and titanium additions on austenite in ductile iron. This study sought to determine the effects of selected levels of these elements on the grain size within ductile iron. A hypoeutectic iron was chosen for testing as the proeutectic phase …

A Study Of Reduced Activation Ferritic Martensitic Metal Core Wire For Wire Arc Additive Manufacturing, Alexander L. Reichenbach

College of Graduate Studies: Theses & Dissertations

This study seeks to determine the technical feasibility of fabricating reduced activation ferritic martensitic (RAFM) steel parts, using a wire arc additive manufacturing (WAAM) process. The WAAM process, manufactures a part by depositing layers of metal onto a substrate to build a large scale near net shape part. RAFM alloy steels are next generation steels designed to resist radiation effects in the radiation intense working environments, such as nuclear reactors. To achieve this, process development and testing to design the WAAM production process with the custom RAFM filler wire was carried out. Several welding waveform modes were tested, and it …

Development Of Oxide Dispersion Strengthening (Ods) Alloys Powder For Additive Manufacturing, Changyu Ma

Graduate Theses, Dissertations, and Problem Reports (ETD)

Additive manufacturing (AM) fabricated oxide dispersion strengthened (ODS) alloys are given high expectations for critical structural components such as the first stage turbine blade for their excellent creep strength and oxidation resistance compared to superalloys. However, the powder feedstock processing is still an open question since current state-of-the-art processes are not capable of achieving ultrafine strengthening elements such as Y₂O₃ in powder which leads to agglomeration issues in as-consolidated alloys. In this research, the oxidation behavior and stability of ultrafine oxide in AM-printed alloys using mechanically alloyed powders were evaluated at 1100 ^oC. In addition, a …

Study Of The Thermodynamic Properties Absorbation Sulfur Storage Gas Of Zinc And Copper Industry, Berdiyarov Tilovkabulovich Berdiyarov Dr., Sh. T. Khojiev, S. T. Matkarimov, Sh. Munosibov

Technical science and innovation

The article considers the problems of utilization of industrial gases formed in the production of copper and ore containing sulfur anhydrides. Currently, the composition of process gases entering the gas purification department is approximately 6-7% SO₂, 0.2-0.3% SO₃ and other gases, until sulfuric acid is obtained from these gases, the sulfate is treated in a counter-scheme with 8% sulfate acid. The aim is to first reduce the temperature of the exhaust gases and second to avoid flying components such as as As, F, Se. As a result of the studies, the amount of SO₂ in the …

Study Of Alloy And Process Modifications To Design Hydrogen Resilient High Hardness Steels, William R. Williams

Theses and Dissertations

High hardness steels (HHS) are vulnerable to hydrogen embrittlement, which can lead to rapid degradation of mechanical properties. Improved resistance to hydrogen embrittlement would be beneficial to many industries including construction, automotive, and military. A comparison study was performed to assess the hydrogen susceptibility of select commercially available and in-house designed HHS alloys. Slow strain rate tensile tests, performed with specimens charged with various levels of hydrogen, provided a macroscopic view of the onset of hydrogen embrittlement. Hydrogen permeation and thermal desorption spectroscopy tests determined the uptake and diffusivity of hydrogen through the material. The evaluation of hydrogen susceptibility for …

The Process-Structure-Property-Performance Of Aisi 1020​, Jonathan Wellman, Tate James, Robbie Christman, Brian Broom

ME 4133/6133 Mechanical Metallurgy

AISI 1020 is widely used in many different industries due to its high strength, high ductility, high machinability, and good weldability. AISI 1020 has a number of applications. Low carbon steel can be used on a macroscale to build bridges, and low carbon steel can be used on smaller scales such as Lawnmower blades. Low carbon steel is the material of choice for lawn mower blades because of its ability to bend before it breaks. The ductile attribute of low carbon steel also has many other benefits.

Ti-6al-7nb Utilization In Surgical Implants, Michael O. Fleming

ME 4133/6133 Mechanical Metallurgy

This presentation discusses the processing, structure, properties, and performance of Ti-6Al-7Nb in relation to use as a surgical implant.