Materials Science and Engineering Commons^™

Macro - And Microstructure Evaluation And Field Applications Of Concrete With Recycled Glass Pozzolan, Marija Krstic

Dissertations and Theses

Concrete is the most used material in the world, second only to water. Conventional concrete is produced with Portland cement (PC). The production of cement is an energy intensive operation that has raised significant environmental concerns, since one ton of cement generates an equal ton of CO₂. In the USA about 90 million tons of cement are used annually, with 3 million tons used in New York. Most contemporary concrete applications for buildings and infrastructure use high-performance concrete (HPC) mixtures which are produced by replacing a percentage of cement with supplementary cementitious materials (SCMs), consisting mainly of fly-ash …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Experimental And Numerical Investigation On The Irregularity Of Carbonation Depth Of Concrete Under Supercritical Condition, Hao Bao Masc, Min Yu Dr., Jianqiao Ye Dr., Lihua Xu Dr., Yin Chi Dr., J Ye

International Conference on Durability of Concrete Structures

The heterogeneity of a cement-based material results in a random spatial distribution of carbonation depth, which may significantly affect the mechanical properties and durability of the material. Currently, there is a lack of both experimental and numerical investigations aiming at a statistical understanding of this important phenomenon. This paper presents both experimental and numerical supercritical carbonation test results of concrete blocks. The random fields of porosity and two-dimension random aggregate model of concrete were proposed for the simulation. The carbonation depths are measured and distributed along the carbonation boundary by the proposed rapid image processing technique, which are then statistically …

Long-Term Performance Of Sustainable Pavements Using Ternary Blended Concrete With Recycled Aggregates, Seth M. Wagner

Theses and Dissertations

The purposes of this study were to (a) design concrete pavement mixtures with recycled concrete aggregates using ternary blends of cementitious materials and a low water-to-binder ratio, (b) measure the fresh and hardened properties of the proposed concrete mixtures and (c) assess the long-term performance of the concrete implementing the use of recycled coarse aggregates. Preliminary investigation into ternary blend combinations via the compressive testing of mortar cubes and isothermal calorimetry was used to predict an optimal blend of cementitious material. Mixes using recycled concrete aggregates at varying replacement rates were tested for fresh and hardened properties using the proposed …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez-Wing, Michele Barbato

Data

Corresponding data set for Tran-SET Project No. 18CLSU03. Abstract of the final report is stated below for reference:

"The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez, Michele Barbato

Publications

The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed challenging for large-scale industrial application due to low SCBA yield (i.e., 3 to 6%). On the other hand, …

Self-Healing Microcapsules As Concrete Aggregates For Corrosion Inhibition In Reinforced Concrete, Homero Castaneda, Marwa Hassan, Miladin Radovic, Jose Milla

Publications

Reinforced Concrete (RC) structures are vital to the US’s civil infrastructure for their strength and versatility. Unfortunately, RC elements deteriorate rapidly when exposed to corrosive environments. One possible solution is to extend the life of RC elements and systems using microencapsulated corrosion inhibitors to reduce the rebar corrosion rate. The capsules house an anodic corrosion inhibitor agent including calcium nitrate (CN) and triethanolamine (TEA). The integration of such microencapsulated materials will enhance the durability and extend the useful life by controlling the corrosion precursors and the corrosion process during damage evolution. Therefore, this work aims to develop and characterize the …

Evaluation Of The Performance And Cost-Effectiveness Of Engineered Cementitious Composites (Ecc) Produced From Region 6 Local Materials, Gabriel Andres Arce Amador, Tyson Rupnow, Marwa Hassan

Publications

The project objective is to develop cost-effective Engineered Cementitious Composites (ECC) with locally available ingredients in Region 6 to address the deficiencies observed in ordinary concrete materials. The study explored the utilization of two types of river sands (coarse and fine), two types of PVA fibers (long and short), four levels of cement replacement with Class F fly ash, and the implementation of recycled crumb rubber in the performance of ECC materials. A total of 24 mix designs were prepared and evaluated in compression, tension, and bending to assess its mechanical properties. Furthermore, the cracking characteristics of the materials produced …

Bridge Deck Overlays Using Ultra-High Performance Concrete, Craig Newtson, Brad Weldon

Publications

This study investigated the use of a locally produced ultra-high performance concrete (UHPC) as an alternative to typical overlay materials. Several bond strength tests including slant-shear, splitting tension, and direct tension tests were performed to assess the bond strength between UHPC and normal strength concrete (NSC) substrate with varying surface textures. Tests were also conducted to assess the early-age and longer-term shrinkage behavior and coefficient of thermal expansion of the UHPC as well as rapid chloride permeability testing. Good bond between UHPC and NSC substrate was observed even with inadequate surface texture. Combined shrinkage and thermal effects were investigated for …

Preparations Of Mno2 Reference Electrodes For Corrosion Monitoring Of Reinforced Concrete, Li Yang, Bing Xu, Hai Wang, Ze-Hua Dong

Journal of Electrochemistry

In this work, the solid reference electrode was assemblied by using the electrochemically synthesized manganese dioxide (MnO₂) (EMD) powder, gel electrolyte and thin mortar layer for the durability evaluation of concrete. The EMD reference electrode exhibited higher potential stability (< 10 mV drift) than the chemically synthesied MnO₂ (CMD) based on half year potential tests in the saturated Ca(OH)₂ solution and hardened mortar. In addition, the EMD electrode was almost insensitive to the presences of chloride ion and corrosion inhibitor. Electrochemical impedance and polarization curves indicate that the EMD electrode had lower charge transfer resistance,higher exchange current density and lower temperature coefficient than the …

A Concrete Water Pasteurization Device For Third World Countries, Andrea R. Murchie

Senior Honors Projects, 2010-2019

In the rural areas of South Africa, as well as many other developing countries, people cook food and sterilize their water by heating over open fires. Many times the fires are inside of homes, which more often than not are very small. Children will often be the ones to tend to the fire, out of necessity while parents and other family members are tending to other work and needs.

The purpose of my Senior Honors Project was to design a concrete vessel that can hold water and heat the water to pasteurization (149°F) when exposed to sunlight for an extended …

Evaluating A New Cem Iii/A Cement For Concretes Exposed To Harsh Acid Rich Environments, David Thompson, Niall Holmes, John Reddy

Conference papers

The Irish Annex to the European specification, performance, production and conformity of concrete, IS EN 206, recommends CEM III/B cement for acid rich environments containing between 66 to 80% GGBS. However, BS 8500, the UK annex to EN 206 and the British Research Establishment (BRE) Special Digest 1, recommends CEM III/A cement with a GGBS range of 36-65%. This project investigated the performance of a new CEM III/A cement produced by Ecocem Ireland in concretes exposed to such environments using an extensive suite of laboratory tests.

In Ireland, up to €5.8bn will be invested to provide fresh drinking water and …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

Advanced Sustainable Concrete Materials For Infrastructure Applications, Kaylea Ann Smith

Masters Theses

"This study was performed to examine the effects of cement replaced by high volumes of Class C fly-ash on durability characteristics of concrete up to 120 days. Specifically, this study investigates possibility of amending American Society for Testing and Materials (ASTM) to allow High Volume Fly-ash (HVFA) concrete to cure until later ages prior to testing instead of 28 days. Five mix designs were compared with varying fly-ash percentages from 0 to 70% (by total cementitious mass). No other additives were present in any of the five mix designs. Water-to-cementitious ratio (w/cm) and total cementitious material remained constant as 0.40 …

Using A Centrifuge For Quality Control Of Pre-Wetted Lightweight Aggregate In Internally Cured Concrete, Albert E. Miller

Open Access Theses

Early age shrinkage of cementitious systems can result in an increased potential for cracking which can lead to a reduction in service life. Early age shrinkage cracking can be particularly problematic for high strength concretes, which are often specified due to their high strength and low permeability. However, these high strength concretes frequently exhibit a reduction in the internal relative humidity (RH) due to the hydration reaction (chemical shrinkage) and self-desiccation which results in a bulk shrinkage, termed autogenous shrinkage, which is substantial at early ages. Due to the low permeability of these concretes, standard external curing is not always …

Durability Of Silane Sealer In A Highly Alkaline Environment, Cameron David Murray

Graduate Theses and Dissertations

Alkali-silica reaction (ASR) is a chemical reaction between siliceous minerals present in certain aggregates and alkalis in the concrete pore solution. The reaction can lead to expansion and severe damage in concrete members. One method to mitigate ASR expansion is to use a penetrating sealer such as silane. A set of columns located in a food preparation facility was treated with silane and a complimentary laboratory study was performed. A cleaning regimen involving application of an alkaline cleaner is employed at the facility, followed by rinsing with hot, pressurized water. The purpose of this research is to evaluate the effectiveness …

Transport Properties Of Nano-Silica Contained Self-Consolidating Concrete, Borhan Moradi

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this research study, transport properties of various self-consolidating concretes (SCCs) containing nano-particles (SiO2) were investigated. Nano-silica replaced a portion of the cementitious materials at different replacement levels ranging from 1.5 to 7.5% by weight. For the purpose of this investigation, flow, bulk, and transport properties of SCCs were studied. The investigated transport properties were absorption, water penetration, rapid chloride permeability, capillary absorption, rapid migration, and chloride diffusion. Transport properties of nano-silica SCCs were also compared to those of equivalent silica fume (micro silica) contained concretes, as well as those of control mixture (concrete without nano or micro silica).

Test …

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

An Investigation Of Waste Glass-Based Geopolymers Supplemented With Alumina, Mary U. Christiansen

Dissertations, Master's Theses and Master's Reports - Open

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production.

Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have …

Kelvin Probe Electrode For Contactless Potential Measurement On Concrete-Properties And Applications, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

The practical feasibility of using a Kelvin Probe as a novel reference electrode in the measurement of both potential and polarization pulse response of reinforcing steel in concrete is demonstrated. Potential values measured using a KP reflect greater stability and repeatability than can typically be attained with conventional reference electrodes. Duplicate reinforced concrete beam test specimens with well-differentiated centrally corroding rebar segments were analyzed using both the Kelvin Probe (KP) and a conventional Saturated Calomel Electrode (SCE). Potential profile maps were developed using potential values recorded under static conditions with both the SCE and the KP. Nominal polarization resistance was …

Effects Of Alternate Cementitious Materials On Compressive Strength And Environmental Impacts Of Cement Mix Designs., Mitchell R. Bush

Materials Engineering

Specific proportions of Portland cement, fly ash, and blast furnace slag cement mixtures where chosen by a ternary phase diagram to be investigated. By experimental testing and company data history fly ash was limited to not exceed 30% and contribution of Portland cement must be over 50%. Ten chosen mix designs were batched by following ASTM C305-94 and cured for twenty-eight and forty-two days, the extended cure length allows the reaction of pozzolanic material with calcium hydroxide to complete. Compressive strength testing at forty-two days yielded low strength for mix designs with 20% or less Portland cement compared to our …

Investigating The Use Of Pozzolans In Portland Cement Concrete And Inorganic Polymer Mortar, Omar Abdelmalek Saleh

UNLV Theses, Dissertations, Professional Papers, and Capstones

The use of pozzolans offers promising signs for a change in the cement industry. Pozzolan in its natural and artificial forms can be used to improve cement properties or to synthesize new cement. This study investigates the use of pozzolans in portland cement concrete and inorganic polymer mortar (geopolymer mortar).

This thesis is divided into two phases. Phase 1 investigates the use of natural pozzolan as a partial replacement of portland cement in concrete. In this phase two types of class N pozzolan are used separately to develop concrete mixtures contain different percentages of class N pozzolan. Fresh concrete properties …

Introducing Fly Ash Into Lsi's Recipe, Andrew Mathias Beckrich

All Graduate Theses, Dissertations, and Other Capstone Projects

There has been published data that states that concrete producers can use Fly Ash as an alternative to Portland cement and still generate similar or better strength properties. By applying these principles to our industry and products, what new processes will need to be put in place and followed? What is the correct combination/portion of Fly Ash that will produce similar and better results as well as the adjusted new recipes? What type of cost is associated with the introduction of this new ingredient? Lastly, how does this affect the quality and reputation of the product?

The Quantification Of The Fly Ash Adsorption Capacity For The Purpose Of Characterization And Use In Concrete, Zeyad Tareq Ahmed

Dissertations, Master's Theses and Master's Reports - Open

Fly ash has been shown to be an effective replacement for portland cement in concrete mixtures. However, many fly ash materials contain unburned carbon from the combustion process. Unburned carbon in fly ash adsorbs air entraining admixtures (AEAs) reducing their effectiveness in providing a specified air void system in concrete materials. Measurement tools and methods for characterization of the adsorption properties of fly ash materials are necessary for beneficial use of fly ash materials in concrete. In this research, two methods were developed to measure and quantify the adsorption capacity AEAs on fly ash materials. The first method is the …

Recycling Waste Latex Paint In Overlays, Rigid Pavements, And Pervious Concrete, Oscar Inez Quiroz

UNLV Theses, Dissertations, Professional Papers, and Capstones

With over 16 million gallons of latex paint (WLP) being disposed every year it is the largest by volume, liquid hazardous waste in the United States. WLP is difficult to recycle and hazardous to the environment due to the volatile organic compounds it contains. Several methods exist for disposing WLP including paint swaps, combustion, drying and discarding in a landfill, and by placing pigments in cement. Many communities are moving to dispose WLP by drying and placing in a landfill due to the reduced cost. However, this is the least preferred technique for the environment because it creates a need …

Electrochemical Detection For The Corrosion Of Reinforcing Steel In Concrete During Immersion And Drying Cycles, Bing-Li Jia, Fa-He Cao, An-Na Chen, Jian-Qing Zhang

Journal of Electrochemistry

The corrosion behavior of reinforcing steel in concrete under dry-wet cycle condition has been studied by electrochemical noise(EN) compared with the electrochemical impedance spectroscopy(EIS),SEM micrographs and EDS.The statistical method has been employed to analyze the EN data of reinforcing steel in concrete,which revealed three different corrosion stages of reinforcing steel in concrete,including the dissolution of the passive film,the active corrosion and the cumulation of corrosion product.The wavelet transform has also been employed,which indicated that steel in concrete with pH 1 is associated with uniform corrosion,while steel in concrete with pH 3 and pH 7 are associated with localized corrosion,such as …

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.