Materials Science and Engineering Commons^™

Floating Wind Farm Experiments Through Scaling For Wake Characterization, Power Extraction, And Turbine Dynamics, Juliaan Bossuyt, OndˇRej FercˇÁk, Zein Sadek, Charles Meneveau, Dennice Gayme, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

In this study, wind and water tunnel experiments of turbulent wakes in a scaled floating wind farm are performed. Scaling of a floating wind farm with a scaling ratio of 1:400 is made possible by relaxing geometric scaling of the turbine platform system, such that the dynamic response can be correctly matched, and to allow for relaxing Froude scaling such that the Reynolds number can be kept large enough. Four dimensionless parameters, describing the relative importance of wind and wave loads compared to turbine inertia, are used to guide the scaled floater design. Free decay tests of the pitch and …

Mechanical Characterization Of Functionally Graded M300 Maraging Steel Cellular Structures, Bradley Jay Sampson

Theses and Dissertations

Traditional methods for increasing the energy absorption of a structure involve using a stronger material or increasing the volume of the structure, resulting in a higher cost or additional weight. Additive manufacturing (AM) can be used to maximize the energy absorption of materials with the ability to create complex geometries such as cellular structures. Previous work has shown that the energy absorption of additively manufactured parts can be improved through functionally graded cellular structures; however, this strategy has not been applied to ultra-high strength steel materials. This work characterizes the effect of multiple functional-grading strategies (e.g. uniform, rod-graded, size-graded) on …

Moisture Effects On Visible Near-Infrared And Mid-Infrared Soil Spectra And Strategies To Mitigate The Impact For Predictive Modeling, Francis Hettige Chamika Anuradha Silva

Theses and Dissertations

Instrumental disparities and soil moisture are two of the key limitations in implementing spectroscopic techniques in the field. This study sought to address these challenges through two objectives. The first objective was to assess Visible-near infrared (VisNIR) and mid-infrared (MIR) spectroscopic approaches and explore the feasibility of transferring calibration models between laboratory and portable spectrometers. The second objective addressed the challenge of soil moisture and its impact on spectra. The portable spectrometers demonstrated comparable performance to their laboratory-based counterparts in both regions. Spiking with extra-weight, was the most effective calibration transfer method eliminating disparities between instruments. The samples were rewetted …

A Review On Ship Recycling Industry In Bangladesh From Global Perspective, Ahammad Abdullah, Zobair Ibn Awal, M Ziauddin Alamgir, Md. Jobayer Mia, Farihatul Mim, Utpal K. Dhar

Journal of Ocean and Coastal Economics

At present, the global center of the ship breaking and recycling industry is in South Asia, specifically Bangladesh, India, and Pakistan. These three countries account for 70–80 percent of the international recycling market for ocean-going vessels, with China and Turkey covering most of the remaining market. Only about 5 percent of global volume is scrapped outside these five countries. Bangladesh has environmentally beneficial coastal region and affordable labor that make the shipbreaking and recycling business as a potential sector for the country. In addition, ship recycling and its related businesses are helping to solve our nation’s unemployment issues at all …

Thermally Rearranging Polyimide Networks For High-Temperature Applications, William Guzman

Dissertations

High-performance polymers can retain functional properties when exposed to long-term or short-term durations of harsh conditions, such as mechanical action, at elevated temperatures (>177 °C). A mixture of intramolecular and intermolecular forces of and between polymer chains provide excellent property retention at elevated temperatures. Specifically, the highly aromatic nature of high-performance polymer backbones provides outstanding thermal stability, which is typically attributed to π-π stacking. However, the interrelationship between thermal stability and high aromaticity creates a challenging structure-processing relationship paradigm, which causes poor polymer processability in most high-performance polymers. Herein, it was demonstrated that rationally designing a crosslinking phenylethynyl imide …

Cobalt Chromium In Biomedical Applications And The Development Of A Pspp Map, Nouralhouda Jamal

BCoE Publications

During the world wars, Cobalt-Chromium (Co-Cr) alloys gained prominence for their use in aircraft engine components, where they exhibited high temperature strength and durability. They are used in a wide range of industries due to their unique set of qualities, particularly strength, corrosion resistance, and biocompatibility. They have emerged as versatile materials with a broad spectrum of applications, from aerospace and automotive components to biomedical implants.

This paper presents a thorough analysis of its composition, processing techniques, microstructure, mechanical properties, and performance characteristics. The primary goal of this project is to develop a PSPP (Process, structure, properties, and performance) map …

Modification Strategies For Development Of 2d Material-Based Electrocatalysts For Alcohol Oxidation Reaction, Haichang Fu, Zhangxin Chen, Xiaohe Chen, Fan Jing, Hua Yu, Dan Chen, Binbin Yu, Yun Hang Hu, Yanxian Jin

Michigan Tech Publications

2D materials, such as graphene, MXenes (metal carbides and nitrides), graphdiyne (GDY), layered double hydroxides, and black phosphorus, are widely used as electrocatalyst supports for alcohol oxidation reactions (AORs) owing to their large surface area and unique 2D charge transport channels. Furthermore, the development of highly efficient electrocatalysts for AORs via tuning the structure of 2D support materials has recently become a hot area. This article provides a critical review on modification strategies to develop 2D material-based electrocatalysts for AOR. First, the principles and influencing factors of electrocatalytic oxidation of alcohols (such as methanol and ethanol) are introduced. Second, surface …

Modification Strategies For Development Of 2d Material-Based Electrocatalysts For Alcohol Oxidation Reaction, Haichang Fu, Zhangxin Chen, Xiaohe Chen, Fan Jing, Hua Yu, Dan Chen, Binbin Yu, Yun Hang Hu, Yanxian Jin

Michigan Tech Publications

2D materials, such as graphene, MXenes (metal carbides and nitrides), graphdiyne (GDY), layered double hydroxides, and black phosphorus, are widely used as electrocatalyst supports for alcohol oxidation reactions (AORs) owing to their large surface area and unique 2D charge transport channels. Furthermore, the development of highly efficient electrocatalysts for AORs via tuning the structure of 2D support materials has recently become a hot area. This article provides a critical review on modification strategies to develop 2D material-based electrocatalysts for AOR. First, the principles and influencing factors of electrocatalytic oxidation of alcohols (such as methanol and ethanol) are introduced. Second, surface …

Process-Driven Microstructure Tailoring During Additive Manufacturing Of Ti-6al-4v, Ahmet Alptug Tanrikulu

Material Science and Engineering Dissertations - Archive

In recent years, additive manufacturing (AM) has attracted the attention of many researchers due to the technology providing opportunities in terms of improved functionality, production repeatability, efficiency, and cost and time issues. While AM techniques made possible the realization of complex geometries, their use in critical applications have faced challenges due to the anisotropic characteristic of AM-built parts. More specifically, non-equilibrium AM processes involve steep temperature gradients and rapid solidification, yielding a unique microstructure, e.g., columnar-shaped grains with preferred texture, in final AM-built products and hence anisotropic mechanical properties. Despite significant studies on improving the microstructure of AM-built parts, it …

Spatially Resolved Elastic Modulus Of Magnesium Silicate Hydrate: A Cementitious Material, Arif Syed

Material Science and Engineering Theses - Archive

Magnesium-based cements such as magnesium silicate hydrate (MSH) have drawn interest as an environmentally friendly substitute for ordinary Portland cement because of their potential for reduced carbon footprint. The precise determination of these materials' elastic moduli is important to better assess their mechanical performance. Atomic force microscopy (AFM) is an effective tool for precise and spatially resolved quantification of nanomechanical characteristics of materials, including thin films. In this study, elastic modulus maps of MSH grown on single crystal mica surfaces were obtained using amplitude modulation-frequency modulation AFM. The effects of the Mg:Si ratio and morphology on the elastic modulus of …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

Developing High-Performance 2d Heterostructured Electrocatalysts And Photocatalysts For Hydrogen Production And Utilizationsts And Photocatalysts For Hydrogen Production And Utilization, Xiaohan Ma

All Dissertations

H₂ is a pivotal chemical in modern society, not only as a clean energy carrier but also as a versatile chemical reactant. However, traditional hydrogen production and utilization heavily rely on thermocatalysis, which is highly energy-intensive and can result in heavy carbon emission and severe environmental problems. Photocatalysis and electrocatalysis are greener alternatives to thermocatalysis that can capitalize on the renewable sunlight and electricity and thus dramatically reduce energy requirements. However, heterogeneous electro/photocatalysts are still far from application to hydrogen economy due to the lack of design principles that can lead to sufficient efficiency. To address this challenge, the …

Fabrication Of Alumina Membranes From Uv Resin– Alumina Particle Slurries, Dominique Henry Porcincula

Master's Theses

Ceramics membranes are made in a wide variety of different techniques using a wide variety of different materials. However, many of the common techniques utilize a slurry of ceramic particles, additives, and either organic solvent or water that is shaped into a membrane, left to dry, and then sintered together. Drying is a time consuming process, often requiring several hours for the liquid medium to evaporate. Defect formation caused by development of partial pressures across the drying membrane, including cracks and warpage, also typically occurs during the drying process. To address this, slurries of ceramic particles made with a low …

An Icfd Fluid Model Used In A Mash Tl-6 Vehicle Model, Md Zunayed Habib

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this thesis was to develop an ICFD finite element model of a partially filled deformable container suitable for impact scenarios. This model will be later incorporated into the existing TL-6 vehicle model, which is a tractor-tank trailer vehicle model. Previous finite element fluid models for the TL-6 vehicle used an elastic fluid model, which could not predict the fluid behavior correctly.

A study was conducted on the ICFD modeling and an improved ICFD model has been developed using the LS-DYNA, a finite element analysis software. Different properties and parameters of the fluid and the container were adopted …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Radiation Exposure Calibration Of The Al2o3:C With Radium-226 And Cesium-137 Using The Osl Method, Selma Tepeli Aydin

All Theses

Optically stimulated luminescence (OSL) dosimetry was utilized to calibrate Al₂O₃:C powder dosimeters, available commercially as the nanoDot® from Landauer Inc., and compare the dosimeter response to radium-226 (²²⁶Ra) and cesium-137 (¹³⁷Cs). The signal from the OSL was quantified using a microSTARii^® OSL reader also produced by Landauer Inc. Dose-response curves were developed for ²²⁶Ra and ¹³⁷Cs experiments (5 dosimeters each) at thirteen absorbed doses. Individual dosimeter response was tracked by serial number. Linear regression analysis was performed to determine if there were significant differences between the intercepts of the …

Evaluation Of The Long-Term Performance Of Ogfc In South Carolina, Rishiraj Brahmbhatt

All Theses

Since the 1970s, South Carolina has employed open graded friction courses (OGFC) on high-speed asphalt roadways to enhance wet weather safety. While these mixes have indeed enhanced safety, they still grapple with durability issues, particularly concerning raveling. This research aimed to assess the prolonged performance of OGFC pavements in South Carolina, with a specific emphasis on isolated raveling occurrences. In 2012, the South Carolina Department of Transportation (SCDOT), constructed the first Warm Mix OGFC test section in South Carolina on I-20 Eastbound in Kershaw County, spanning 3.9 miles, using the Evotherm additive and excluding fibers. Following the success of this …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Ionically Crosslinked Cellulose Nanocrystals By Metal Nitrates For The Preparation Of Stable Emulsions With Tunable Interface Properties, Joseph Batta-Mpouma, Gurshagan Kandhola, Jin-Woo Kim

Materials Science and Engineering Faculty Publications and Presentations

Biologically extracted cellulose nanocrystals (CNCs) are rod-like and amphiphilic materials with surface-exposed (hydrophilic sites) and hidden (hydrophobic sites) hydroxyl groups. These physicochemical characteristics make CNCs suitable for use as emulsifying agents to stabilize emulsions. Stable oil-in-water emulsions, using sulfated (i.e., – SO₃−) CNCs that were ionically crosslinked with alkaline-earth (i.e., Mg ²⁺) or transition-d-block (i.e., Zn ²⁺) metal cations, were developed without the use of any synthetic surfactants or prior functionalization of pure CNCs with hydrophobic molecules. Various emulsion surface properties such as interfacial tension, surface charge, surface chemistry, as well as rheology were characterized. Ionically …

Data-Driven Multiscale Modeling Of Dye Aggregates In Dna For Excitonic Applications, Austin Biaggne

Boise State University Theses and Dissertations

In this dissertation, a data-driven, multi-scale approach was implemented to study the structural, electronic, and dynamical behavior of dye monomers and aggregates for excitonic applications. The excitonic behavior of dye aggregates depends on both the constituent monomer properties as well as the relative dye orientations that make up the aggregate. Dye monomer properties can be augmented with substituents, but with a wide range of substituent types, ideal dye derivatives should be identified. To control the aggregation of dyes, DNA can be used as a scaffold, however, the ways in which dyes interact with each other and with DNA is not …

Novel Sensors And Measurement Techniques For Thermal Properties In Extreme Environments, Katelyn Wada

Boise State University Theses and Dissertations

Advancements in thermal properties analysis is crucial for improvement of existing and next generation reactors, space exploration, and environmental safety. Extreme environments pose a great hurdle for instrumentation to measure real time thermal properties due to the extreme temperatures, high radiation, and variable electromagnetic environments. Nevertheless, measurement systems are tremendously important for the design, P.E.rformance, and safety considerations of nuclear fuels, space crafts, and deep sea/deep earth drilling. Thermal properties may change significantly in these environments creating challenging problems for temperature and thermal conductivity measurement systems. A recent focus has surrounded improvements in such systems for accurate determination of temperature …

Molecular Control Of Triplet-Pair Spin Polarization And Its Optoelectronic Magnetic Resonance Probes, Obadiah G. Reid, Justin C. Johnson, Joel D. Eaves, Niels H. Damrauer, John E. Anthony

Chemical and Materials Engineering Faculty Publications

Preparing and manipulating pure magnetic states in molecular systems are the key initial requirements for harnessing the power of synthetic chemistry to drive practical quantum sensing and computing technologies. One route for achieving the requisite higher spin states in organic systems exploits the phenomenon of singlet fission, which produces pairs of triplet excited states from initially photoexcited singlets in molecular assemblies with multiple chromophores. The resulting spin states are characterized by total spin (quintet, triplet, or singlet) and its projection onto a specified molecular or magnetic field axis. These excited states are typically highly polarized but exhibit an impure spin …

Advancing Additive Manufacturing For Biomedical Applications: Antimicrobial And X-Ray Absorptive Composite Filaments For Fused Filament Fabrication, John M. Arnold Jr

LSU New Orleans Theses and Dissertations

The objective of this research was to investigate the use of nano- and microparticle amendments for the creation of Poly-lactic Acid composite materials for use in biomedical applications using the Fused Filament Fabrication process of Additive Manufacturing. Composites were created with the goal of imparting the useful properties of antimicrobial activity and x-ray absorption to the material. In addition to testing the efficacy of the particle amendments in achieving the desired properties, the thermal and mechanical properties of the composite materials were tested to ensure that the composites would be compatible with the Fused Filament Fabrication process and would produce …

Sustainable Diamond-Like Carbon Fabricated Gravure Cylinders For Printing Fine Lines Of Electrodes And Graphic Structures, Chandramohan Seetharamiah Srinivasaraju

Dissertations

The main objective of this work is to evaluate the potential of Diamond-Like Carbon (DLC) as an alternative to chrome for use on gravure cylinders. DLC coatings consist of carbon atoms, arranged into a diamond-like structure that closely resembles that of natural diamond. In contrast to chrome, DLC is environmentally friendly. The focus of the study is to determine the viability of DLC as a substitute material for chrome to be used on gravure cylinders by determining key material properties and evaluating printing performance.

In the first research paper, four DLC variants (Standard DLC, A-DLC, S-DLC, and Organic Silica) and …

Exploring The Potential Of Tesla Valve For Filtering And Sorting Microscale Active Swimmers: A Computational Study, Ariel Rogers, Zhiyao He, Yong Wang

Physics Faculty Publications and Presentations

It is well-known that a Tesla valve allows fluids to flow unidirectionally without moving parts; however, how Tesla valves interact with active matters and the potential applications of Tesla valves in biology remain largely unexplored. Here, we present a computational study on the potential use of Tesla valves for filtering and sorting microscale active swimmers such as bacteria. We investigated the behavior of microscale swimmers passing through the Tesla valve at different linear and angular velocities using numerical simulations and quantified the diodicity of the Tesla valve for active swimmers. Our results demonstrate that the Tesla valve can effectively filter …

The Shape Modulation Of Laser-Induced Nanowelded Microstructures Using Two Colors, Ariel Rogers, Isabelle Niyonshuti, Jun Ou, Diksha Shrestha, Deborah Okyere, Jingyi Chen, Yong Wang

Physics Faculty Publications and Presentations

The light-based nanowelding of metallic nanoparticles is of particular interest because it provides convenient and controlled means for the conversion of nanoparticles into microstructures and the fabrication of nanodevices. In this study, we investigated the wavelength dependence of laser-induced nanowelded shapes of silver nanoparticles (AgNPs). We observed that the nanowelded microstructures illuminated with only a 405 nm laser were more branched than those formed via illumination using both the 405 nm and 532 nm lasers. We quantified this observation by two compactness descriptors and examined the dependence of the power of the 532 nm laser. More importantly, to understand the …

Role Of Mechanical Signaling In Bone Tissue, Scott Aaron Birks

Boise State University Theses and Dissertations

As the global population ages and life expectancy continues to rise, osteoporosis continues to be a growing worldwide health concern. The International Osteoporosis Foundation reports 1 in 3 women over the age of 50 years and 1 in 5 men worldwide will experience osteoporotic fractures in their lifetime, costing between 5 and 6.5 trillion USD annually in Canada, Europe, and the United States alone. The need for preventative measures to reduce age-related bone loss is clear, not only to improve quality of life for countless individuals but also to relieve the economic burden this condition imposes.

Exercise is a proven …

Investigating The Influence Of Surface Finishing Methods On Corrosion Of Additively Manufactured Ss316l, Joshua R. Fadeley

Boise State University Theses and Dissertations

Additive Manufacturing (AM), namely with metal, has seen a surge in growth and interest over recent years. A wide array of industries is developing new products to take advantage of this budding technology. In order to enable adoption of this technology, understanding of the differences of AM versus traditional manufacturing on the resultant materials properties of printed components is important. The work done for this study fell into two separate categories of work.

The first effort of this work involved the installation, certification, and operation of the first laser powder bed fusion (LPBF) printer at the Center for Advanced Energy …

Additive Manufacturing Of Microelectronic Devices For Extreme Environments, Nicholas Mckibben

Boise State University Theses and Dissertations

This work encompasses a comprehensive exploration of advanced manufacturing techniques for fabricating microelectronic devices compatible with extreme environments. The research integrates the fields of chemistry, nanomaterials, and additive manufacturing to achieve remarkable progress in sensor development, with a particular emphasis on aerosol jet printing (AJP), surface acoustic wave (SAW) devices, patterned graphene growth, and surface functionalization. The investigation begins with the AJP process development of a commercial silver nanoparticle ink, culminating in the fabrication of a piezoelectric SAW transducer that was prototyped as a high-temperature thermometer, showing excellent linearity when validated to 200°C. Next, the investigation continued with the development …

Design And Characterization Of A Novel Eef2k Degrader With Potent Therapeutic Efficacy Against Triple-Negative Breast Cancer, Changxin Zhong, Rongfeng Zhu, Ting Jiang, Sheng Tian, Xiaobao Zhao, Xiaoya Wan, Shilong Jiang, Zonglin Chen, Rong Gong, Linhao He, Jin-Ming Yang, Na Ye, Yan Cheng

Markey Cancer Center Faculty Publications

Dysregulated eEF2K expression is implicated in the pathogenesis of many human cancers, including triple-negative breast cancer (TNBC), making it a plausible therapeutic target. However, specific eEF2K inhibitors with potent anti-cancer activity have not been available so far. Targeted protein degradation has emerged as a new strategy for drug discovery. In this study, a novel small molecule chemical is designed and synthesized, named as compound C1, which shows potent activity in degrading eEF2K. C1 selectively binds to F8, L10, R144, C146, E229, and Y236 of the eEF2K protein and promotes its proteasomal degradation by increasing the interaction between eEF2K and the …