Materials Science and Engineering Commons^™

Synthesis And Spectroscopic Study Of Complex Compounds Mn(Ii), Co(Ii), Cu(Ii) And Zn With 5-Amino-2-Mercaptobenzimidazole, Lobar Gapurova, Dilnoza Rakhmonova, Shakhnoza Kadirova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work is to study the effect of the nature of electron-donor and electron-withdrawing substituents in the molecules of heterocyclic ligands, the nature of acidoligands and transition metal ions on the properties of the synthesized coordination compounds. A method for the synthesis of new complex compounds of Mn (II), Cо (II), Cu (II) and Zn with 5-amino-2-mercaptobenzimidazole has been developed and the composition and structure of the synthesized complex compounds have been studied using modern physicochemical methods, such as elemental, thermogravimetric, X-ray phase analysis and IR spectroscopy. Coordination competing donor centers, electronic and geometric structures of the …

Resistance Of Polystyrol Concrete To Dynamic Impact Loads, Natalya Dubovitskaya, Zamira Mukhamedbaeva, Abduvali Mukhamedbaev

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the study is to increase the resistance of polystyrene concrete obtained from recycled polystyrene to dynamic shock loads. The issues of resistance of polystyrene concrete to compression forces with increasing load are considered. It was found that in terms of impact resistance, polystyrene concrete can be classified as a viscous material capable of absorbing high energy of shock loads. It has been determined that when Na₂SO₄ is introduced as a hardening accelerator, polystyrene concrete samples can absorb an impact energy of more than 178.5 J.

Features Of The Formation Of The Coating Structure On Titanium-Based Alloys, Uchkun Rakhimov, Nasiba Abduraimova, Yulbarskhon Mansurov

CHEMISTRY AND CHEMICAL ENGINEERING

Previously shown that coatings formed on titanium by plasma electrolytic oxidation (PEO) in an electrolyte with zirconium sulfate Zr(SO₄)₂ consisted of ZrO₂ and TiO₂ oxides, their surface layer is enriched with zirconium, they have good protective properties in chlorine-containing media. The resulting layers have a fairly regular distribution of relatively small pores, with a diameter of about 1 μm or less, on the surface. The composition and structure of PEO layers depend on both the composition of the electrolyte and the modes of formation. It is of scientific and practical interest to elucidate the effect …

Flexible Planar Metamaterials With Tunable Poisson’S Ratios, Nicholas Pagliocca, Kazi Zahir Uddin, Ibnaj Anamika Anni, Chen Shen, George Youssef, Behrad Koohbor

Henry M. Rowan College of Engineering Departmental Research

This research reports on the design, fabrication, and multiscale mechanical characterization of flexible, planar mechanical metamaterials with tailorable mechanical properties. The tunable mechanical behavior of the structures is realized through the introduction of orthogonal perforations with different geometric features. Various configurations of the perforations lead to a wide range of Poisson’s ratios (from −0.8 to 0.4), load-bearing properties, and energy absorption capacities. The correlations between the configuration of the perforations and the auxetic response of the structures are highlighted through computational and experimental characterizations performed at multiple length scales. It is demonstrated that the local in-plane rotation of the solid …

Computational Investigation Of The Post-Yielding Behavior Of 3d-Printed Polymer Lattice Structures, Abdalsalam Fadeel, Hasanain Abdulhadi, Golam Newaz, Raghavan Srinivasan, Ahsan Mian

Mechanical and Materials Engineering Faculty Publications

Sandwich structures are widely used due to their light weight, high specific strength, and high specific energy absorption. Three-dimensional (3D) printing has recently been explored for creating the lattice cores of these sandwich structures. Experimental evaluation of the mechanical response of lattice cell structures (LCSs) is expensive in time and materials. As such, the finite element analysis (FEA) can be used to predict the mechanical behavior of LCSs with many different design variations more economically. Though there have been several reports on the use of FEA to develop models for predicting the post-yielding stages of 3D-printed LCSs, they are still …

Implementation Of Multiscale Mechanisms In Finite Element Analysis Of Active Composite Structures, Amany G. Micheal Prof., Yehia Bahei El Din Prof.

Centre for Advanced Materials

Composite structures reinforced with electrically active filaments are modeled with the finite element method while the underlying thermo-electromechanical coupling phenomena and damage are taken into consideration. At the outset, structural analysis is performed with a general-purpose finite element code and a special material routine, which propagates local phenomena to the overall scale is utilized. The material routine implements an interactive, multiscale analysis, which provides seamless integration of the mechanics at the composite’s micro, macro, and structural length scales. The interface between the multiscale material routine and the finite element code is made through nonmechanical strains caused by damage, and piezo/pyro-electric …

Synergic Antitumor Effect Of Photodynamic Therapy And Chemotherapy Mediated By Nano Drug Delivery Systems, Mozhgan Aghajanzadeh, Mostafa Zamani, Fereshteh Rajabi Kouchi, Josh Eixenberger, Dorsa Shirini, David Estrada, Farhad Shirini

Materials Science and Engineering Faculty Publications and Presentations

This review provides a summary of recent progress in the development of different nano-platforms for the efficient synergistic effect between photodynamic therapy and chemotherapy. In particular, this review focuses on various methods in which photosensitizers and chemotherapeutic agents are co-delivered to the targeted tumor site. In many cases, the photosensitizers act as drug carriers, but this review, also covers different types of appropriate nanocarriers that aid in the delivery of photosensitizers to the tumor site. These nanocarriers include transition metal, silica and graphene-based materials, liposomes, dendrimers, polymers, metal–organic frameworks, nano emulsions, and biologically derived nanocarriers. Many studies have demonstrated various …

Thermoforming Process Effects On Structural Performance Of Carbon Fiber Reinforced Thermoplastic Composite Parts Through A Manufacturing To Response Pathway, Madhura Limaye, Sai Aditya Pradeep, Anmol Kothari, Sushil Savla, Akshat Agha, Srikanth Pilla, Gang Li

Publications

Thermoforming process of thermoplastic-based continuous CFRP's offer a major advantage in reducing cycle times for large-scale productions, but it can also have a significant impact on the structural performance of the parts by inducing undesirable effects. This necessitates the development of an optimal manufacturing process that minimizes the introduction of undesirable factors in the structure and thereby achieves the targeted mechanical performance. This can be done by first establishing a relationship between the manufacturing process and mechanical performance and successively optimizing it to achieve the desired targets. The current study focuses on the former part, where a manufacturing-to-response (MTR) pathway …

Facile One-Step Hydrothermal Method For Nico2s4/Rgo Nanocomposite Synthesis For Efficient Hybrid Supercapacitor Electrodes, Ahmed Mysara, Sayed Y. Attia, Fouad I. El-Hosiny, M A. Sadek, Saad G. Mohamed, M M. Rashad

Nanotechnology Research Centre

Spinel nickel-cobalt sulfide (NiCo2S4) supported on reduced graphene oxide (rGO) was fabricated through a facile one-step hydrothermal method for energy storage applications. The distribution of the NiCo2S4 nanoparticles on the rGO surface was found to improve the supercapacitive performance of the assembled device. The NiCo2S4/rGO nanocomposite exhibits outstanding electrochemical behavior with a capacity (C)/specific capacitance (Cs) of 536 C g−1/1072 F g−1 at a current density of 1 A g−1. To further investigate the electrochemical behavior of the NiCo2S4/rGO nanocomposite, a hybrid supercapacitor (HSC) was constructed utilizing a NiCo2S4/rGO positive electrode and an activated carbon …

Nodule Formation On Copper Electrodeposits In The Rotating Cylinder Hull Cell, Joseph Bauer, Michael S. Moats

Materials Science and Engineering Faculty Research & Creative Works

Nodulation formation during the electrolytic production of high-purity copper can lead to impurity entrapment and/or increased energy consumption. The rotating cylinder Hull cell (RCHC) was used to study copper nodule formation under mass transport conditions similar to industrial electrolytic copper production. The main advantage of the RCHC is that a wide range of current densities can be produced in a single experiment with well-defined mass transfer conditions. Visible nodule formation was observed at current densities greater than 250 A/m2, which is an iavg/iL ratio of 0.30 for a simulated conventional electrowinning cell. Statistical analysis was also performed using the Weibull …

Design And Fabrication Of Nanostructured Electrodes For Complementary Electrochemical And Photoelectrochemical Water Splitting, Kholoud El Sayed Abousalem

Theses and Dissertations

Designing highly active, durable, and nonprecious electrodes for overall water splitting is of urgent scientific importance to realize sustainable hydrogen production. Accordingly, the need to search efficient energy production systems is of crucial necessity. In this thesis, two various systems for sustainable hydrogen production have been reported using electrochemical and photoelectrochemical pathways. In the first part of the thesis, electrochemical water splitting involving both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) has been established. To this end, an innovative approach is demonstrated to synthesize flower-like 3D homogenous trimetallic Mn, Ni, Co phosphide catalysts directly on nickel foam via …

The Integrated Scheduling Of Flexible Manufacturing Systems Using Petri Net Modeling And Heuristic Searching, Mohammed Mohammed Magdy Mohammed

Archived Theses and Dissertations

No abstract provided.

Synthesis Of Lithium-Rich Manganese-Based Layered Cathode Materials And Study On Its Structural Evolution Of First Cycle Overcharge, Chen-Xu Luo, Chen-Guang Shi, Zhi-Yuan Yu, Ling Huang, Shi-Gang Sun

Journal of Electrochemistry

Lithium-rich manganese-based cathode materials have become one of promising cathode materials due to their low cost and large discharge specific capacity exceeding 250 mAh·g^-1. However, their problems such as low coulombic efficiency of first cycle and apparent voltage decay influence commercialization process. The high charging voltage will cause instability of structure and increase the hidden danger of the battery. Therefore, structural evolution of first cycle at higher voltage needs to be further studied. In this work, the precursor was synthesized by the co-precipitation method, and the lithium-rich manganese-based layered cathode materials were prepared by lithium-mixed and high-temperature sintering, …

Progress Of Pt-Based Catalysts In Proton-Exchange Membrane Fuel Cells: A Review, Long Huang, Hai-Chao Xu, Bi Jing, Qiu-Xia Li, Wei Yi, Shi-Gang Sun

Journal of Electrochemistry

Fuel cells are energy conversion devices that convert chemical energy directly into electricity. It has the advantages of high energy density, high utilization efficiency of fuel, clean and noiseless during working. Among all kinds of fuel cells, proton exchange membrane fuel cells (PEMFCs) are most popular since PEMFCs function at near ambient temperature, while their power densities are higher than those of other fuel cells. Currently, Pt-based nanomaterials are still the unreplaceable catalysts in commercialized PEMFCs. The lack of low-cost and high-performance cathode catalysts is still one of key factors that hampers the commercialization of PEMFCs. In this review, the …

Advances Of Phosphide Promoter Assisted Pt Based Catalyst For Electrooxidation Of Methanol, Meng Li, Li-Gang Feng

Journal of Electrochemistry

Transition metal phosphide (TMP), as an ideal catalytic promoter in methanol fuel oxidation, has received increased attention because of its multifunctional active sites, tunable structure and composition, as well as unique physical and chemical properties and efficient multi-composition synergistic effect. Some advances have been made for this catalyst system recently. In the current review, the research progresses of transition metal phosphides (TMPs) in the assisted electrooxidation of methanol including the catalysts fabrication and their performance evaluation for methanol oxidation are reviewed. The promotion effect of TMPs has been firstly presented and the catalyst systems based on the different metal centers …

A High-Performance Continuous-Flow Mea Reactor For Electroreduction Co2 To Formate, Pei-Xuan Liu, Lu-Wei Peng, Rui-Nan He, Lu-Lu Li, Jin-Li Qiao

Journal of Electrochemistry

The electrochemical carbon dioxide reduction reaction (CO₂RR) is a promising approach to produce liquid fuels and industrial chemicals by utilizing intermittent renewable electricity for mitigating environmental problems. However, the traditional H-type reactor seriously limits the electrochemical performance of CO₂RR due to the low CO₂ solubility in electrolyte, and high ohmic resistance caused by the large distance between two electrodes, which is unbeneficial for industrial application. Herein, we demonstrated a high-performance continuous flow membranes electrode assembly (MEA) reactor based on a self-growing Cu/Sn bimetallic electrocatalyst in 0.5 mol·L^-1 KHCO₃ for converting CO₂ to …

A Flexible Enzymeless Glucose Sensor Via Electrodepositing 3d Flower-Like Cos Onto Self-Supporting Graphene Tape Electrode, Jiang Li, Zuo-Peng Li, Yun-Feng Bai, Su-Xing Luo, Yong Guo, Ya-Yan Bao, Rong Li, Hai-Yan Liu, Feng Feng

Journal of Electrochemistry

Three-dimensional (3D) nanostructural Flower-like cobalt sulfide (CoS) on flexible self-supporting graphene tape electrode (GTE) with remarkably electrocatalytic activity toward glucose was successfully prepared by electrodeposition. Structural characterizations revealed that the electrodeposited CoS was highly dispersed on GTE as an active material. The fabricated binder-free and self-standing CoS/GTE shows a good linear response in the range of 0.025 ~ 1.0 mmol·L^-1, reaching a high glucose sensitivity value of 323.3 μA·(mmol·L ^-1)^-1·cm^-2 and a low detection limit of 8.5 μmol·L ^-1 (S/N = 3). Moreover, the as-prepared sensor was well applied for glucose …

Oxidative Efficiency Of Ozonation Coupled With Electrolysis For Treatment Of Acid Wastewater, Ze-You Hu, Feng-Yun Xiang, Ji-Qiang Mao, Ya-Lei Ding, Shao-Ping Tong

Journal of Electrochemistry

Establishment of an ozone-based advanced oxidation process (AOPs-O₃) for effective treatment of acid wastewater is an important and difficult task. The process of ozonation coupled with electrolysis (electrolysis-ozonation, E-O₃) has been reported to effectively degrade pollutants in neutral solution. We studied the efficiency of E-O₃ for degradation of acetic acid (HAc, an ozone inert chemical) in acid solution and found that E-O₃ had high oxidative efficiency at pH less than 3. For example, 52.2% of 100 mg·L^-1 HAc could be removed by E-O₃ in 120 min at pH 1.0, but only 2.2% …

Acetate Solutions With 3.9 V Electrochemical Stability Window As An Electrolyte For Low-Cost And High-Performance Aqueous Sodium-Ion Batteries, Dao-Yun Lan, Xiao-Feng Qu, Yu-Ting Tang, Li-Ying Liu, Jun Liu

Journal of Electrochemistry

Low-cost and high-safety aqueous sodium-ion batteries have received widespread attention in the field of large-scale energy storage, but the narrow electrochemical stability window (1.23 V) of water limits the energy density of aqueous sodium-ion batteries. The “water-in-salt” strategy which uses the interaction between cations and water molecules in the solution can inhibit water decomposition and broaden the electrochemical stability window of water. In this work, two types of low-cost salts, namely, ammonium acetate (NH₄CH₃COOH) and sodium acetate (NaCH₃COOH), were used to configure a mixed aqueous electrolyte for aqueous sodium-ion batteries. The solution consisted of …

Influence Of Pinholes On Water Vapor And Oxygen Permeation Of Packaging Foil And Films, Petri Johansson, Johanna Lahti, Jurkka Kuusipalo

Journal of Applied Packaging Research

Controlling of moisture and oxygen permeation through the packaging material is essential in most packaging applications. With multilayer structures of different barrier materials, there is possibility to create desired barrier properties to the package. The challenge is to plan appropriate barrier level, e.g. WVTR and OTR, theoretically to the package before producing the package. Furthermore, in specific packages there is a need to control the permeation e.g. respiration in vegetable packages. Typically foils and polymer films have high barrier properties, therefore, permeation can be controlled by producing artificial pinholes in these kinds of packages.

Influence of artificial pinholes in aluminium …

Examining The Effect Of A Chitosan Biopolymer On Alkali-Activated Inorganic Material For Aqueous Pb(Ii) And Zn(Ii) Sorption, Sukanta K. Mondal, Chenglin Wu, Felix C. Nwadire, Ali A. Rownaghi, Aditya Kumar, Yusuf Adewuyi, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Biopolymers and alkali-activated materials have attracted a great deal of attention as adsorbents for the removal of heavy metal contaminants from aqueous solutions. Both materials are sustainable and feature unique properties, but biopolymers are relatively more expensive or difficult to prepare and exhibit low mechanical and surface properties, a narrow pH range, and thermal stability. In this study, hybrid adsorbents were prepared from both types of material, by alkali activation of low-cost fly ash precursors accompanied by incorporation of 0-2%mass chitosan biopolymer. Two types of alkaline activating solutions, NaOH and Na2SiO3, were employed to generate two sets of hybrid adsorbents …

Exciton Delocalization In A Dna-Templated Organic Semiconductor Dimer Assembly, Xiao Wang, Ruojie Sha, William B. Knowlton, Nadrian C. Seeman, James W. Canary, Bernard Yurke

Materials Science and Engineering Faculty Publications and Presentations

A chiral dimer of an organic semiconductor was assembled from octaniline (octamer of polyaniline) conjugated to DNA. Facile reconfiguration between the monomer and dimer of octaniline–DNA was achieved. The geometry of the dimer and the exciton coupling between octaniline molecules in the assembly was studied both experimentally and theoretically. The octaniline dimer was readily switched between different electronic states by protonic doping and exhibited a Davydov splitting comparable to those previously reported for DNA–dye systems employing dyes with strong transition dipoles. This approach provides a possible platform for studying the fundamental properties of organic semiconductors with DNA-templated assemblies, which serve …

Design And Fabrication Of A Low-Cost, Portable, Battery-Operated Surface Enhanced Raman Scattering (Sers) Optical Device, Blessing Adewumi

LSU Doctoral Dissertations

Raman Spectroscopy is a time-honored, non-invasive method for analyzing and identifying the molecular composition of materials. However, unenhanced Raman Spectroscopy has extremely low sensitivity which limits its sensing capability. SERS brings rough nano-metallic surfaces in contact with the material molecules to enormously enhance the Raman signals.

The sensitivity of SERS can be exploited in probe applications where the spectrometer needs to be brought near the specimen. For example, a long optical fiber coupled to a SERS device can be used to characterize and identify easy-to-reach cancerous tissues in organisms. Unfortunately, background signals in a long fiber can easily mask any …

Materials And Methodologies For Spectroscopic And Optical Analytical Applications In Cultural Heritage Conservation Science, Lyndsay Nichole Kissell

Dissertations and Theses

The field of conservation science falls in the intersection of science and art. The work of conservation scientists may include any single subdiscipline of chemistry, though it is most commonly a highly interdisciplinary field taking skills from analytical, organic, and inorganic chemistry, as well as surface and materials science. The aims of conservation scientists are to answer questions about the production and aging of material cultural heritage. Knowing the materials used by an artist can lead to insight about the intentions of the object and knowing how those materials degrade will enable the use of preventative measures to ensure the …

Random Lasing In Nano-Crystalline Zinc-Oxide Films, Benito Reynaldo Resendiz

Dissertations and Theses

In this thesis, we explore the preparation of random lasers (RLs) using solution-deposited, randomly packed nano-particle films of zinc oxide (ZnO) impregnated with silicon dioxide (SiO₂) nanospheres. RLs have their scatterers randomly oriented, while their lasing comes from light propagating along closed paths through the scattering environment. It is shown here that random lasing is readily observed in films made of submicron sized ZnO particles. Adding transparent SiO₂ nanospheres to the films, we show there is an effective improvement of the lasing that is observable in all of the samples spectra. Specifically, we found that the lasing …

Quasi-Static Multifunctional Characterization Of 3d-Printed Carbon Fiber Composites For Compressive-Electrical Properties, Ritesh Ghimire, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multifunctional carbon fiber composites provide promising results such as high strength-to-weight ratio, thermal and electrical conductivity, high-intensity radiated field, etc. for aerospace applications. Tailoring the electrical and structural properties of 3D-printed composites is the critical step for multifunctional performance. This paper presents a novel method for evaluating the effects of the coating material system on the continuous carbon fiber strand on the multifunctional properties of 3D-printed composites and the material's microstructure. A new method was proposed for the quasi-static characterization of the Compressive-Electrical properties on the additively manufactured continuous carbon fiber solid laminate composites. In this paper, compressive and electrical …

Uncertainties Induced By Processing Parameter Variation In Selective Laser Melting Of Ti6al4v Revealed By In-Situ X-Ray Imaging, Zachary A. Young, Meelap M. Coday, Qilin Guo, Minglei Qu, S. Mohammad H. Hojjatzadeh, Luis I. Escano, Kamel Fezzaa, Tao Sun, Lianyi Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective laser melting (SLM) additive manufacturing (AM) exhibits uncertainties, where variations in build quality are present despite utilizing the same optimized processing parameters. In this work, we identify the sources of uncertainty in SLM process by in-situ characterization of SLM dynamics induced by small variations in processing parameters. We show that variations in the laser beam size, laser power, laser scan speed, and powder layer thickness result in significant variations in the depression zone, melt pool, and spatter behavior. On average, a small deviation of only ~5% from the optimized/reference laser processing parameter resulted in a ~10% or greater change …

A Deep Learning Approach To Design And Discover Sustainable Cementitious Binders: Strategies To Learn From Small Databases And Develop Closed-Form Analytical Models, Taihao Han, Sai Akshay Ponduru, Rachel Cook, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

To reduce the energy-intensity and carbon footprint of Portland cement (PC), the prevailing practice embraced by concrete technologists is to partially replace the PC in concrete with supplementary cementitious materials [SCMs: geological materials (e.g., limestone); industrial by-products (e.g., fly ash); and processed materials (e.g., calcined clay)]. Chemistry and content of the SCM profoundly affect PC hydration kinetics; which, in turn, dictates the evolutions of microstructure and properties of the [PC + SCM] binder. Owing to the substantial diversity in SCMs' compositions-plus the massive combinatorial spaces, and the highly nonlinear and mutually-interacting processes that arise from SCM-PC interactions-state-of-the-art computational models are …

A Deep Learning Approach To Design And Discover Sustainable Cementitious Binders: Strategies To Learn From Small Databases And Develop Closed-Form Analytical Models, Taihao Han, Sai Akshay Ponduru, Rachel Cook, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

To reduce the energy-intensity and carbon footprint of Portland cement (PC), the prevailing practice embraced by concrete technologists is to partially replace the PC in concrete with supplementary cementitious materials [SCMs: geological materials (e.g., limestone); industrial by-products (e.g., fly ash); and processed materials (e.g., calcined clay)]. Chemistry and content of the SCM profoundly affect PC hydration kinetics; which, in turn, dictates the evolutions of microstructure and properties of the [PC + SCM] binder. Owing to the substantial diversity in SCMs' compositions–plus the massive combinatorial spaces, and the highly nonlinear and mutually-interacting processes that arise from SCM-PC interactions–state-of-the-art computational models are …

Centrifugal Assembly Of Bijel Ropes Via Helical Microfluidics, Shankar P. Kharal

Theses and Dissertations

Bicontinuous interfacially jammed emulsion gels (bijels) are soft materials that retain a liquid bicontinuous network stabilized by an interfacially jammed layer of nanoparticles. In this thesis, we investigated a microfluidic twisting method to fabricate micro-ropes of nano-structured bijel fibers. This method shows how weak microfibers with tensile strengths of a few kPa can be reinforced by 4 orders of magnitude by means of microfluidic twisting. Microfluidic twisting allows to produce continuous bijel fiber ropes of controllable architecture. Modelling the fluid flow field reveals the rope geometry dependence on a subtle force balance composed of rotational and translational shear stresses. However, …