Materials Science and Engineering Commons^™

Comparison Of Fatigue Performance Between Additively Manufactured And Wrought 304l Stainless Steel Using A Novel Fatigue Test Setup, M. M. Parvez, Y. Chen, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

In this research, a novel adaptive controlled fatigue testing machine was designed for bending type high cycle fatigue test. A unique dual gauge section Krouse type mini specimen was designed for simply supported transverse bending. Displacement controlled fatigue tests were implemented using an electromechanical actuator. The variation in the control signal and load observed during the test provides unique insights into realizing the deterioration of the specimen due to fatigue. These analyses were utilized to compare the fatigue performance of wrought and additively manufactured 304L stainless steel. The influence of the build direction on fatigue performance was also investigated by …

Compressive And Bending Performance Of Selectively Laser Melted Alsi10mg Structures, D. Murphy, O. Fashanu, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, H. Misak, D. Klenosky

Materials Science and Engineering Faculty Research & Creative Works

Selective laser melting (SLM) is a widely used additive manufacturing technique that effectively manufactures complex geometries such as cellular structures. However, challenges such as anisotropy and mechanical property variation are commonly found due to process parameters. In a bid to utilize this method for the commercial production of cellular structures, it is important to understand the behavior of a material under different loading conditions. In this work, the behavior of additively manufactured AlSi10Mg under compression, bending, and tension loads was investigated. Vertical and horizontal build directions are compared for each type of loading. Specimens were manufactured using the reduced build …

Effective Elastic Properties Of Additively Manufactured Metallic Lattice Structures: Unit-Cell Modeling, Okanmisope Fashanu, David Murphy, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, Ben Brown, John Porter

Materials Science and Engineering Faculty Research & Creative Works

Lattice structures are lightweight materials, which exhibit a unique combination of properties such as air and water permeability, energy and acoustic absorption, low thermal conductivity, and electrical insulation. In this work, unit-cell homogenization was used to predict the effective elastic moduli of octet-truss (OT) lattice structures manufactured using selective laser melting (SLM). OT structures were manufactured using a Renishaw AM 250 SLM machine with various relative densities. Compression test was carried out at strain rate 5 x 10^-3 m^-1 using an MTS frame. Finite element analysis was used in the determination of the OT’s effective elastic properties. Results …

Elevated Temperature Mechanical And Microstructural Characterization Of Slm Ss304l, G. R. Hecht, Sriram Praneeth Isanaka, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

SLM built SS304L was annealed and water quenched to minimize residual stress and avoid carbide precipitation. Mini-tensile characterization of strength and elongation at temperature conditions up to 800°C, along with observations of the associated microstructural transformations were utilized to understand the changes produced in SLM SS304L. As-built and annealed specimens were found to exhibit decreasing strength and elongation with increasing temperature as expected. Carbide precipitates appeared after short times at high temperatures within both as-built and annealed specimens for all cases, but no brittle intermetallic phase development was observed for any of the temperatures investigated. While the lack of Sigma, …

Optimizing The Valorization Of Industrial By-Products For The Induction Healing Of Asphalt Mixtures, Amir Tabakovic, Marta Vila-Cortavitarte, Daniel Jato-Espino, Daniel Castro-Fresno

Articles

Self-healing within asphalt pavements is the process whereby road cracks can be repaired automatically when thermal and mechanical conditions are met. To accelerate and improve this healing process, metal particles are added to asphalt mixtures. However, thisapproach is costly both in economic and environmental terms due to the use of virgin metallic particles. So, even though the self-healing of asphalt mixtures has been widely addressed in experimental terms over the years, there is a lack of research aimed at modelling this phenomenon, especially with the purpose of optimizing the use of metal particles through the valorization of industrial by-products. As …

Hydcem: A New Cement Hydration Model, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models are useful to predict, understand and describe the behaviour of different cementitious-based systems. They are indispensable for undertaking long-term performance and service life predictions for existing and new products for generating quantitative data in the move towards more sustainable cements while optimising natural resources. One such application is the development of cement-based thermoelectric applications.

HYDCEM is a new model to predict the phase assemblage, degree of hydration, heat release and changes in pore solution chemistry over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, is aimed at …

Evaluation Of Biodegradability Characteristics Of Cellulose-Based Film As Per Is/Iso 14855-1, Narayan C. Saha Dr, Gaurav Madhu Dr, Diksha B. Kadu Ms

Journal of Applied Packaging Research

Biodegradable polymers (especially those derived from plant sources) begin their lifecycle as renewable resources, usually in the form of starch or cellulose. In this paper, the evaluation of biodegradability of cellulose-based polymer film under controlled composting conditions as per the guidelines of IS/ISO 14855 (Part-1) standard has been described. Microcrystalline cellulose (MCC) powder was taken as positive-control polymer. The apparatus used to analyse the degree and rate of biodegradation was developed indigenously. The validation of the biodegradability testing apparatus was also performed as per the prescribed test method given in IS/ISO 14855-1.

Implementing Population-Based Mass Drug Administration For Malaria: Experience From A High Transmission Setting In North Eastern Uganda, Richard Elliott

Materials Science and Engineering Faculty Publications and Presentations

Background: Mass drug administration (MDA) is a suggested mean to accelerate efforts towards elimination and attainment of malaria-free status. There is limited evidence of suitable methods of implementing MDA programme to achieve a high coverage and compliance in low-income countries. The objective of this paper is to assess the impact of this MDA delivery strategy while using coverage measured as effective population in the community and population available.

Methods: Population-based MDA was implemented as a part of a larger program in a high transmission setting in Uganda. Four rounds of interventions were implemented over a period of 2 years at …

Investigation Of The Electrode Polarization Effect For Biosensor Applications, Anil Koklu

Mechanical Engineering Research Theses and Dissertations

My research focuses on electrokinetic transport. Particularly, in this dissertation, we focus on fabrication and testing of micro electrodes with nanostructured surfaces to minimize the electrode polarization (EP) effects for biosensor applications. In the first study, electrochemical deposition of gold nanoparticles on to planar gold electrodes was used to generate rough surfaces. Dendritic nanostructures that reduced EP up to two orders of magnitude was obtained by optimizing the deposition conditions. These structures also enhanced dielectrophoresis (DEP) response of our bio-chips, making them usable in physiological buffers. In further studies we discovered a universal scaling of EP in the frequency domain, …

Laboratory Evaluation Of Cold In-Place Recycling Asphalt Mixtures Using A Balanced Mix Design, Ahmed Saidi

Theses and Dissertations

The objective of this research study is to present a procedure for designing Cold In-Place Recycling (CIR) mixtures through balancing cracking and rutting for these mixtures. Eight CIR mixtures were prepared using two recycling agents (foamed and emulsified asphalts), then cured for three days at two temperatures (140oF and 50oF), and compacted at two gyration levels (30 and 70 gyrations). The CIR mixtures were prepared at constant dosages of water and cement, 3% and 1%, respectively. Air void of each CIR performance test specimen was determined using the CoreLok device. The rutting susceptibility of these mixtures was then evaluated using …

General Nonlinear-Material Elasticity In Classical One-Dimensional Solid Mechanics, Ronald Joseph Giardina Jr

LSU New Orleans Theses and Dissertations

We will create a class of generalized ellipses and explore their ability to define a distance on a space and generate continuous, periodic functions. Connections between these continuous, periodic functions and the generalizations of trigonometric functions known in the literature shall be established along with connections between these generalized ellipses and some spectrahedral projections onto the plane, more specifically the well-known multifocal ellipses. The superellipse, or Lam\'{e} curve, will be a special case of the generalized ellipse. Applications of these generalized ellipses shall be explored with regards to some one-dimensional systems of classical mechanics. We will adopt the Ramberg-Osgood relation …

Development Of Experimental And Finite Element Models To Show Size Effects In The Forming Of Thin Sheet Metals, Jeffrey D. Morris

LSU New Orleans Theses and Dissertations

Abstract

An experimental method was developed that demonstrated the size effects in forming thin sheet metals, and a finite element model was developed to predict the effects demonstrated by the experiment. A universal testing machine (UTM) was used to form aluminum and copper of varying thicknesses (less than 1mm) into a hemispherical dome. A stereolithography additive manufacturing technology was used to fabricate the punch and die from a UV curing resin. There was agreement between the experimental and numerical models. The results showed that geometric size effects were significant for both materials, and these effects increased as the thickness of …

Microstructure And Materials Characterization Of Sol-Gel Synthesized Zro2 Systems, Sungsoo Park, Godlisten Shao

Tanzania Journal of Science

The roles of pH and thermal treatment on the microstructures of sol-gel synthesized mesoporous ZrO2 systems have been investigated. In order to control the crystal structures and particle sizes of the final products, the pH values of the reaction mixtures were controlled between 5 and 12 followed by calcination at temperatures ranging from 450 to 1000 °C. The microstructures of the zirconia systems were then examined by XRD, TEM, TGA, UV-visible DRS and nitrogen physisorption study analyses. It was found that pH values and calcination temperatures have significant influence on the crystallization temperature, phase transformation and particle size of the …

Long-Term Performance Of Sustainable Pavements Using Ternary Blended Concrete With Recycled Aggregates, Seth M. Wagner

Theses and Dissertations

The purposes of this study were to (a) design concrete pavement mixtures with recycled concrete aggregates using ternary blends of cementitious materials and a low water-to-binder ratio, (b) measure the fresh and hardened properties of the proposed concrete mixtures and (c) assess the long-term performance of the concrete implementing the use of recycled coarse aggregates. Preliminary investigation into ternary blend combinations via the compressive testing of mortar cubes and isothermal calorimetry was used to predict an optimal blend of cementitious material. Mixes using recycled concrete aggregates at varying replacement rates were tested for fresh and hardened properties using the proposed …

A Study Of The Electron Regeneration Efficiency Of Solar Cells Fabricated Using Cmc/Pva-, Alginate-, And Xanthan-Based Electrolytes, Nur Farha Shaafi, Saifful Kamaluddin Muzakir, Bouchta Sahraoui

Makara Journal of Technology

A photovoltaic (PV) mechanism consists of three important steps, i.e., (i) electron excitation upon absorption of photon with energy higher than the bandgap of fluorophore, (ii) excited-state electron injection from the fluorophore to the pho-toelectrode, and (iii) electron regeneration from the electrolyte to the fluorophore. An efficient electron regeneration could be achieved upon fulfillment of the requirements of energy alignment, i.e., lowest unoccupied molecular orbital of fluorophore (LUMOfluorophore) > redox potential of electrolyte > highest occupied molecular orbital of fluorophore (HOMOfluorophore). This study investigated the electron regeneration efficiency of excitonic solar cells fabricated using three polymer-based electrolytes, i.e., (i) 60% carboxymethyl cellulose …

Use Of The “Dnachecker” Algorithm For Improving Bioinformatics Research, Nausheen Bhat, Ezra Bernadus Wijaya, Arli Aditya Parikesit

Makara Journal of Technology

Basic Local Alignment Sequencing Tool (BLAST) is a bioinformatics tool used for analyzing nucleotide sequences with regards to their similarity. BLAST can be found online on biological databases such as the National Center for Biotechnology Information (NCBI) and other such repositories. The mechanism of BLAST allows the target sequence to be compared with other sequences to find regions of local similarity, and thus, a comparability quotient that determines the resemblance between the sequences is created. Due to the open-platform nature of the online databanks, several sequences can be accepted with little to no interjections regarding the quality of sequence submitted. …

Study Of Ecological Design Of Residential Complexes Using Spss To Elevate Resident Satisfaction, Soheil Malekpour Kolbadinejad, V. Malekpour Ravasjan, A. Darvish

Makara Journal of Technology

This article reports the general residential satisfaction, affecting ecological factors, and their importance in area in Tehran. The collected field data was analyzed using SPSS. Cronbach's alpha variable was used to determine the reliability of the questionnaire and the Friedman test was used to assess priorities that influence residential satisfaction. The results show that the quality of residential environments and general satisfaction of their residents may be enhanced by identifying these criteria and making appropriate plans for their improvement.

Adsorption Of Heavy Metal Ions By Oil Palm Decanter Cake Activated Carbon, Mohd. Ezreeza Mohamed Yusoff, Juferi Idris, Nahrul Hayawin Zainal, Mohamad Faizal Ibrahim, Suraini Abd-Aziz

Makara Journal of Technology

Adsorption processes are widely used for the removal of heavy metals from waste streams. Oil palm decanter cake (OPDC) is used as a bioadsorbent because of its compositional properties for activated carbon production; moreover, it is a readily available raw material produced in palm oil mills and is thus abundant and cheap. In this study, the OPDC was carbonized at 700 °C and activated using steam at 700 °C to produce oil palm decanter cake activated carbon (AC-OPDC). Batch adsorption experiments were carried out to compare the adsorption capacities of the raw OPDC and the AC-OPDC for heavy metals removal. …

Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks, Heru Purnomo, Srikandi Wahyu Arini

Makara Journal of Technology

Unfired brick is considered as a more environmentally friendly material than fired brick. It has lower mechanical properties than that of fired brick where humidity influences both bricks. Physical and mechanical properties of unfired bricks made of three kinds of mixtures were studied experimentally under three humidity conditions. The first kind of unfired brick was made only with soil and water while the second type was made of a mixture of soil, water and lime, and the third type was a mixture of soil, water, lime and uniform treated coir where 4% of lime mass was substituted with coir mass. …

Component Analysis And Antiangiogenic Activity Of Thailand Stingless Bee Propolis, Eriko Ishizu, Sari Honda, Tosihro Ohta, Boonyadist Vongsak, Shigenori Kumazawa

Makara Journal of Technology

Propolis is a natural resin produced by honey bees from certain plants, has gained popularity as a food and alternative medicine. However, to the best of our knowledge, few studies on native Thailand stingless bee propolis are available. Information on the chemical composition and biological activities of propolis is needed to investigate its potential utility. Recently we have reported the possible plant origin of Thailand stingless bee propolis, Garcinia mangostana. In this study, further component analysis, functional evaluation, and identification of the plant origin of Thailand stingless bee propolis are conducted. Nine xanthones, including α-mangostin, garcinone C, γ-mangostin, cochinchinone T, …

3d Fdtd Method For Modeling Of Seismo-Electromagnetics Disturbance On Crustal Earth, Nabila Husna Shabrina, Yasuhide Hobara, Achmad Munir

Makara Journal of Technology

The paper deals with the modelling of seismo-electromagnetics disturbance on the crustal earth by use of threedimensional (3D) finite-difference time-domain (FDTD) method. The model is built up by discretizing the frontier geographical region between Java Island and Sumatra Island in a cylindrical coordinate system-based 3D object. The proposed method is applied to compute and analyze electromagnetics (EM) fields of the observed very low frequency (VLF) wave used for the investigation. Boundary condition of uniaxial perfectly matched layer (UPML) are applied surrounding the area of computation for truncating the object of simulation. The investigation are focused on the propagation time of …

Spontaneous Selective Deposition Of Iron Oxide Nanoparticles On Graphite As Model Catalysts, Chathura De Alwis, Timothy Leftwich, Pinaki Mukherjee, Alex Denofre, Kathryn Perrine

Michigan Tech Publications, Part 1

Iron oxide nanomaterials participate in redox processes that give them ideal properties for their use as earth-abundant catalysts. Fabricating nanocatalysts for such applications requires detailed knowledge of the deposition and growth. We report the spontaneous deposition of iron oxide nanoparticles on HOPG in defect areas and on step edges from a metal precursor solution. To study the nucleation and growth of iron oxide nanoparticles, tailored defects were created on the surface of HOPG using various ion sources that serve as the target sites for iron oxide nucleation. After solution deposition and annealing, the iron oxide nanoparticles were found to nucleate …

Materials Science And Engineering, Joshua P. Steimel

Pacific Open Texts

This text serves to provide a brief overview of some of the myriad of topics available for study in the field of Materials Science. This is by no means a comprehensive compilation of Materials Science and Engineering topics but is instead meant as an introduction to the topic for entry-level undergraduates who want to pursue a career studying materials.

Oxidation Behavior Of Zirconium, Zircaloy-3, Zircaloy-4, Zr-1nb, And Zr- 2.5nb In Air And Oxygen, Jordan L. Vandegrift, Patrick M. Price, John-Paul Stroud, Clemente J. Parga, Isabella J. Van Rooyen, Brian J. Jaques, Darryl P. Butt

Materials Science and Engineering Faculty Publications and Presentations

The Transient Reactor Test (TREAT) facility at the Idaho National Laboratory currently utilizes a legacy Zircaloy- 3 cladding, which is no longer commercially available. TREAT is air cooled and routinely operates at temperatures well above that of traditional reactor designs. This study investigates the oxidation behavior of pure zirconium and its alloys (Zircaloy-3, Zircaloy-4, Zr-1Nb, Zr-2.5Nb) in Ar+20%O₂ and N₂+20%O₂ atmospheres at temperatures ranging from 400–800 °C to determine which alloy should be implemented as TREAT's cladding. While the oxidation behavior of zirconium based cladding materials has been extensively documented, this study focuses on direct comparison …

Increasing The Functionality Of Additive Manufacturing Through Atmospheric Microplasma And Nanotechnology, Alexander Jon Ulrich

Doctoral Dissertations

Additive Manufacturing (AM) has been changing the manufacturing landscape for the last 20 years. As the interest and demand for both polymer and metal-based 3D printing has grown, the materials and machines used have increased in capabilities. Despite the growth and advancement, there are still a large number of improvements that can be made to add functionality to 3D printers. Metal AM, a subcategory of 3D printing, has garnered much attention among industrial applications with large companies such as General Electric trying to implement the technology to increase innovative designs for motors. Some of the limitations on AM have to …

Migration And Electropolymerization Of Methyl Methacrylate In Hardened Cement Paste Via Electrokinetic Treatment, Xi Xie

Doctoral Dissertations

Porous concrete structures are susceptible to the intrusion of chemical species, such as sulfates, chlorides, and carbon dioxide. Many technologies have been developed to repair or rehabilitate damaged concrete. These include cathodic protection, corrosion inhibitor addition, or the use of coatings and sealers. In recent years, a developing technology, electrokinetic nanoparticle treatment, has been shown to reduce concrete porosity, increase strength, promote corrosion resistance, and extend durability. This dissertation was conducted to explore a novel treatment to reduce the porosity of concrete via the application of electrokinetic transportation and electro-initiated polymerization of methyl methacrylate (MMA).

Potassium persulfate (PSP) was used …

Use Of Rice Husk Ash (Rha) In Flowable Fill Concrete Mix Material, Zahid Hossain, Kazi Tamzidul Islam

Data

Corresponding data set for Tran-SET Project No. 18CASU03. Abstract of the final report is stated below for reference:

"In the way of finding sustainable development, the flowable fill is a relatively new construction technology. Flowable fill is a self-compacting material, which has been developed in recent years. Flowable fill has been used for different applications such as backfilling walls, sewer trenches, bridge abutments, conduit trenches, pile excavations, and retaining walls. This study examines the potential uses of Rice Husk Ash (RHA) as a sustainable cementitious material (SCM) in the preparation of flowable fill concrete. (RHA is an agricultural by-product of …

Self-Healing Concrete Using Encapsulated Bacterial Spores In A Simulated Hot Subtropical Climate, Marwa Hassan, Jose Milla, Tyson Rupnow, Ahsennur Soysal

Data

Corresponding data set for Tran-SET Project No. 18CLSU02. Abstract of the final report is stated below for reference:

"Bacterial concrete has become one of the most promising self-healing alternatives due to its capability to seal crack widths through microbial induced calcite precipitation (MICP). In this study, two bacterial strains were embedded at varying dosages (by weight of cement) in concrete. Beam specimens were used to identify the maximum crack-sealing efficiency, while cylinder samples were used to determine their effects on the intrinsic mechanical properties, as well as its stiffness recovery over time after inducing damage. The concrete specimens were cured …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez-Wing, Michele Barbato

Data

Corresponding data set for Tran-SET Project No. 18CLSU03. Abstract of the final report is stated below for reference:

"The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …