Materials Science and Engineering Commons^™

Palladium Nanoparticles On Zno-Passivated Carbon For Enhanced Performance In Li-O2 Batteries, Mar Piernavieja-Hermida

Research Horizons Day Posters

No abstract provided.

Al/Ti Nanostructured Multilayers: From Mechanical, Tribological, To Corrosion Properties, Sina Izadi

USF Tampa Graduate Theses and Dissertations

Nanostructured metallic multilayers (NMMs) are well-known for their high strength in smaller bilayer thicknesses. Six Al/Ti (NMM) with different individual layer thickness were tested for their mechanical hardness using a nanoindentation tool. Individual layer thicknesses were chosen carefully to cover the whole confined layer slip (CLS) model. Nano-hardness had a reverse relation with the square root of individual layer thickness and reached a steady state at ~ 5 nm bilayer thickness. Decreasing the layer bilayer thickness from ~ 104 nm to ~ 5 nm, improved the mechanical hardness up to ~ 101%. Residual stresses were measured using grazing incident X-ray …

Molecular Combing Of Dna Nanofibers And Comparison To Electrospinning, Tanner L. Buresh

UCARE: Research Products

The goal of these experiments was to create DNA nanofibers through the method of molecular combing (MC) and then compare the MC fibers to fibers created with electrospinning (ES). The experiment was designed and initial samples were created. After confirming that the method would succeed in creating DNA fibers, several parametric studies were performed in order to optimize the experiment and create the most uniform fibers possible. The parametric studies were done on the following variables: substrate material, pH level of DNA solution, and DNA solution concentration. After completion of all experiments, it was determined that although fibers could be …

Management Of A Sever Degloving Foot Injury: A Rare Presentation Of Food Injury In Emergency Department, Ugur Lok, Hasan Buyukaslan, Umut Gulacti, Fatih Dogan, Irfan Aydin

Materials Science and Engineering Faculty Research & Creative Works

Occupational crash injuries of the foot present a significant reconstructive challenge due to the superficial location of structures such as tendon, joint and neurovascular network essential for proper acceptance of weight bearing and shear forces associated with bipedal gait. We discussed here a rare case in which an extensive degloving injury of the foot and combined with knee traumatic dislocation and proximal fibula tip fracture that underwent amputation. The authors suggested that none of treatment modalities of degloving are entirely satisfactory, so that each case must be considered independently with cons and pros

Assessing The Performance Of A Soy Methyl Ester -Polystyrene Topical Treatment To Extend The Service Life Of Concrete Structures, D'Shawn G. Thomas

Open Access Theses

Experimental results show that soy methyl ester (SME), a derivative of soy bean oil, along with the incorporation of polystyrene (PS) is a non-toxic, biodegradable and renewable material that can be used effectively as a topical concrete surface treatment. While, concrete sealants and topical surface treatments can be used to extend to durability of concrete structures, it is difficult to predict the durability of concrete structures sealed with a sealant or topical surface treatment. This is due to a lack of necessary model inputs that can be used to address the durability of concrete structures treated with these materials. In …

Optimization Of Process Parameters In Micro Electrical Discharge Machining (Edm) Of Ti-6al-4v Alloy, Farshid Alavi

Masters Theses & Specialist Projects

Ti-6Al-4V has a wide range of applications such as in the automotive and aerospace industries. Nevertheless, titanium alloys are very difficult to machine by conventional methods. Micro-EDM is a non-conventional machining method that uses the thermal effect of precisely controlled sparks. Manufacturers are looking for the methods and optimal settings to increase the productivity of micro-EDM in terms of lessening machining time and tool wear. Moreover, surface integrity of the machined area is crucial for some products such as biomedical implants.

The objective of this study was to investigate the effects of the micro-EDM process parameters on response variables, in …

Breakdown Voltage Performances Of Aluminum And Copper Conductor Wire Under Compression Stresses, Richard Donald Suchanek Iii

Masters Theses & Specialist Projects

In the global, competitive market of energy transformation, increased operational expenses and depletion of raw materials have resulted in companies pursuing alternate materials to reduce consumer costs. In electrical applications, energy is transformed using materials with high electrical conductive properties. The conductive material used to transmit a signal is called conductor wire and is comprised of any material that has the ability to move charged particles from one point to another without propagation or delay. The conductor wire in many applications is encapsulated in epoxy resin called enamel. The enamel is the insulation system that provides necessary dielectric clearances to …

Clay Nanotube Composites For Antibacterial Nanostructured Coatings, Christen J. Boyer

Doctoral Dissertations

A surging demand for the development of new antimicrobial nanomaterials exists due to the frequency of medical device-associated infections and the transfer of pathogens from highly touched objects. Naturally occurring halloysite clay nanotubes (HNTs) have shown to be ideal particles for polymer reinforcement, time-release drug delivery, nano-reactor synthesis, and as substrate material for nanostructured coatings.

This research demonstrates the feasibility of a novel method for coating HNTs with metals for antibacterial applications. The first ever ability to coat HNTs through electrolysis was developed for customizable and multi-functional antibacterial nanoparticle platforms. HNTs were investigated as substrate for the deposition of copper …

Growth Of Ws2 Thin Photovoltaic Films, Matthew J. Hilfiker, Aaron Ediger, Natale Lanno

UCARE: Research Products

Through research for a material that is low cost, earth abundant, and highly efficient, Tungsten Sulfide (WS₂) has been identified as a promising solution. From literature, it has been shown that WS₂ possesses a band gap of 1.9 eV, which is ideal for a top layer heterostructure cell. While this is a favorable value, other properties needed to understand its value as a photovoltaic material are unknown. Through research, WS₂ films will be grown through a sputtering deposition process and electrical characterization measurements will be performed to study these missing properties.

A Comparison Of American, Norwegian, And Russian Standards In Calculating The Wall Thickness Of Submarine Gas Pipeline, Cindy Dianita, Tatyana Vladimirovna Dmitrieva

Makara Journal of Technology

One of the key issues in the pipeline design is wall thickness calculation. This paper highlights a comparison of wall thickness calculation methods of submarine gas pipeline based on Norwegian Standard (DNV-OS-F101), Indonesian Standard SNI 3474 which refers to American Standard (ASME B31.8), and Russian Standard (VN39-1.9-005-98). A calculation of wall thickness for a submarine gas pipeline in Indonesia (pressure 12 MPa, external diameter 668 mm) gives the results of 18.2 mm (VN39-1.9-005-98), 16 mm (ASME B31.8), and 13.5 mm (DNV-OS-F101).The design formula of hoop stress due to internal pressure is interpreted in different ways for every standard. Only Norwegian …

Vacuum Brazing Of Diamond To Tungsten Carbide, Zhiyong Yin

Graduate Theses & Non-Theses

Diamond tools are increasingly gaining importance as cutting and drilling materials for a wide variety of industrial applications. Polycrystalline diamond (PCD) is the main ultrahard material commercially used in the oil and gas drilling industry. In this study, a reactive brazing process was developed to join polycrystalline diamond (PCD) to WC-13 wt% Co, to form the cutter for fixed-cutter drill bit applications.

Most nonmetals including polycrystalline diamond are not wet by and cannot easily be joined with conventional brazing alloys due to their chemical stability. The experimental approach was first to analyze the effect of adding an active metal (Ti, …

Chlorination And Selective Vaporization Of Rare Earth Elements, Daniel Gaede

Graduate Theses & Non-Theses

No abstract provided.

Electrochemical Characterization Of Xanthate Chemisorption On Copper And Enargite, Tyler Broden

Graduate Theses & Non-Theses

The electrochemical reactions of copper and enargite (Cu₃AsS₄) were studied in the absence and presence of xanthate by cyclic voltammetry (C.V.) using electrodes fashioned from pure copper wire obtained from the Metallurgical and Materials Engineering Department, and an enargite mineral sample obtained from the Orphan Girl mine in Butte, MT. Voltammograms were produced in buffer solutions of pH values ranging from 7-12. Electrochemical reactions were discerned by comparing E_H-pH diagrams calculated from thermodynamics using StabCal, a computer program developed by Dr. Huang at Montana Tech. The chemisorption of xanthate on the surface of copper …

The Anisotropy Of Hexagonal Close-Packed And Liquid Interface Free Energy Using Molecular Dynamics Simulations Based On Modified Embedded-Atom Method, Ebrahim Asadi, Mohsen Asle Zaeem

Materials Science and Engineering Faculty Research & Creative Works

This work aims to comprehensively study the anisotropy of the hexagonal close-packed (HCP)-liquid interface free energy using molecular dynamics (MD) simulations based on the modified-embedded atom method (MEAM). As a case study, all the simulations are performed for Magnesium (Mg). The solid-liquid coexisting approach is used to accurately calculate the melting point and melting properties. Then, the capillary fluctuation method (CFM) is used to determine the HCP-liquid interface free energy (γ) and anisotropy parameters. In CFM, a continuous order parameter is employed to accurately locate the HCP-liquid interface location, and the HCP symmetry-adapted spherical harmonics are used to expand γ …

3d Printed Bone Supplement Materials, Azem Khalifa Yahamed

Dissertations

Three-dimensional (3D) printing is an advanced rapid technology that can be used to make human bone substitutes with exact shape and designed structures, based on models created from actual individual bone medical Digital Imaging and Communications in Medicine (DICOM) images. Biocompatible polymers have been selected for 3D printing of human bone structures. The thermoplastics were 3D printed with Fused Deposition Modeling (FDM) are Acrylate Butadiene Styrene (ABS), Polylactic Acid (PLA) and ULTEM 9085 (a polyetherimide). The polyamide PA 2200 was 3D printed using Selective Laser Sintering (SLS). Digital ABS (a crosslinked acrylic polymer) was 3D printed using PolyJet Technology. These …

Microgalvanic Corrosion Behavior Of Cu-Ag Active Braze Alloys Investigated With Skpfm, Armen Kvryan, Kari Livingston, Corey M. Efaw, Kyle Knori, Brian J. Jaques, Paul H. Davis, Darryl P. Butt, Michael F. Hurley

Materials Science and Engineering Faculty Publications and Presentations

The nature of microgalvanic couple driven corrosion of brazed joints was investigated. 316L stainless steel samples were joined using Cu-Ag-Ti and Cu-Ag-In-Ti braze alloys. Phase and elemental composition across each braze and parent metal interface was characterized and scanning Kelvin probe force microscopy (SKPFM) was used to map the Volta potential differences. Co-localization of SKPFM with Energy Dispersive Spectroscopy (EDS) measurements enabled spatially resolved correlation of potential differences with composition and subsequent galvanic corrosion behavior. Following exposure to the aggressive solution, corrosion damage morphology was characterized to determine the mode of attack and likely initiation areas. When exposed to 0.6 …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Post-Repair Seismic Assessment Of Rc Bridges Damaged With Fractured Column Bars - A Numerical Approach, Ruili He, Yang Yang, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Seismic repair of reinforced concrete (RC) bridge columns has been studied extensively during the past several decades; however, few studies have been conducted on the influence of the column repair (member level) on the post-repair performance of bridge structures (system level). In a previous experimental study by the authors, a method was developed to rapidly repair severely damaged RC bridge columns to enable the quick reopening of the bridge to emergency traffic. Thus, a lower limit state was used for the repair design, so that the lateral strength and drift capacity of a repaired RC column with fractured longitudinal bars …

Plasma Processing Of Superconducting Radio Frequency Cavities, Janardan Upadhyay

Physics Theses & Dissertations

The development of plasma processing technology of superconducting radio frequency (SRF) cavities not only provides a chemical free and less expensive processing method, but also opens up the possibility for controlled modification of the inner surfaces of the cavity for better superconducting properties. The research was focused on the transition of plasma etching from two dimensional flat surfaces to inner surfaces of three dimensional (3D) structures. The results could be applicable to a variety of inner surfaces of 3D structures other than SRF cavities. Understanding the Ar/Cl₂ plasma etching mechanism is crucial for achieving the desired modification of Nb …

Cyclic Behavior Of A Hybrid Light Gauge And Hss Mezzanine Structural System, Michael John Kren

Master's Theses (2009 -)

Cold-formed steel is emerging as an alternative material in the building industry to hot-rolled steel for smaller buildings and indoor structures also called mezzanines. Cyclic testing of a full-scale mezzanine structures composed of cold-formed structural channel beams connected to hollow structural steel (HSS) columns cap plates using wedge expansion anchors at the base plate to generate rotation restraint, is performed in this research. The characteristics of the structure will be explained by displaying full experimental results of structural testing. Unfortunately, limited experimental data outlining the behavior of these structures is available and design criteria is very limited. Thus, there is …

Techniques And Technologies For Decontaminating Chemically Contaminated Premise Plumbing Infrastructure, Karen S. Casteloes

Open Access Theses

Recent large-scale drinking water chemical contamination incidents in Canada and the U.S. have affected more than 1,000,000 people. In all cases premise plumbing has become contaminated and disparate plumbing decontamination approaches have been applied. Premise plumbing components include the service line and piping within the building as well as various appurtenances (i.e., tanks, valves, fixtures). The overall research goal was to identify techniques and technologies that can be used for premise plumbing decontamination. To achieve this goal two separate studies were conducted and are presented as two independent thesis chapters.

The study described in Chapter 1 was designed to understand …

Fabrication And Drying Of Cnc-Based Microcapsules With Pdms/Antimicrobial Oil Cores Via The Microcapillary Device, Yunze Dai

Open Access Theses

Cellulose nanocrystals (CNC) which are the crystalline regions of elementary microfibrils found in cellulose are becoming a promising biocompatible nanoscale building block. We report on the generation, evolution, and drying of CNC capsules with oil cores, obtained from double emulsion drops. Microcapillary devices were used to generate the double emulsion drops with outer diameters ranging from 75 to 225 µm, and shell thicknesses ranging from 5 to 60 µm. 10 wt% aqueous CNC suspensions without and with the addition of PEGDA, a UV-crosslinkable binder, were used as the shell material while 10 cSt PDMS oil was used in the core. …

Nanoscale Phonon Thermal Conductivity Via Molecular Dynamics, Jonathan M. Dunn

Open Access Theses

Molecular dynamics (MD) simulations provide a useful and simple means of calculating the nanoscale thermal properties of materials, which requires special analysis since the thermal properties of materials change when their dimensions reach the nanoscale. In this research, MD is used to investigate the nanoscale phonon thermal transport of materials that are attracting much interest in the areas of materials science and nuclear physics. In order to evaluate two distinct methods of calculating the thermal conductivity of materials using MD, the simulation methods are first applied to Si. Once an understanding of each simulation method is established, they are then …

Effect Of Humidity On The Creep Response Of Cellulose Nanocrystals Films, Marianne C. Valone

Open Access Theses

Cellulose nanocrystals (CNCs) are a derivative of cellulose, the Earth’s most abundant source of a sustainable polymer. There are many applications for CNCs such as batteries, antimicrobial films, flexible displays and drug delivery. This research is focused on CNCs films and the mechanical properties once humidity was introduced.

The creation of self-aligned CNCs films was utilized to perform dynamic mechanical analysis (DMA) testing. The Forest Products Lab (FPL) in Madison, Wisconsin provided the CNCs used. Both 3.5 wt.% and 9.1 wt.% films were made and tested. A DMA method was created to test the creep response of the CNCs films …

Identification Of The Zinc-Oxygen Divacancy In Zno Crystals, Maurio S. Holston, Eric M. Golden, Brant E. Kananen, John W. Mcclory, Nancy C. Giles, Larry E. Halliburton

Faculty Publications

An electron paramagnetic resonance (EPR) spectrum in neutron-irradiated ZnO crystals is assigned to the zinc-oxygen divacancy. These divacancies are observed in the bulk of both hydrothermally grown and seeded-chemical-vapor-transport-grown crystals after irradiations with fast neutrons. Neutral nonparamagnetic complexes consisting of adjacent zinc and oxygen vacancies are formed during the irradiation. Subsequent illumination below ∼150 K with 442 nm laser light converts these (V²⁻_Zn − V²⁺_O)⁰ defects to their EPR-active state (V⁻_Zn − V²⁺_O)⁺ as electrons are transferred to donors. The resulting photoinduced S = 1/2 spectrum of the …

Thermal Properties, Crystallinity, And Oxygen Permeability Of Na-Montmorillonite Reinforced Plasticized Poly(Lactic Acid) Film, Kurniawan Yuniarto, Yohanes Aris Purwanto, Setyo Purwanto, Bruce A. Welt, Hadi Karia Purwadaria, Titi Candra Sunarti

Makara Journal of Technology

Introducing unmodified organically clay/Na-montmorillonite (Na-MMT) was applied into plasticized poly(lactic acid) PLA to produce film composites by direct casting. Film composite structure, the crystallinity degree and form, and thermal properties were carried out using X-ray diffraction and differential scanning calorimetry. The effect of Na- MMT to the tortuous path and the crystallinity degree in the plasticized film composites were calculated in oxygen barrier properties. Chromatogram film composites resulted in an intercalated structure that showed peak diffraction angle shift at about 0.2o. Then, a peak diffraction pattern was indicated in α-form crystal structure. Plasticized PLA has a crystallinity degree at 34%, …

Residual Strength Analysisof Asymmetrically Damaged Ship Hull Girderusing Beam Finite Element Method, Muhammad Zubair Muis Alie

Makara Journal of Technology

The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method is used for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4) and a three-cargo-hold model of a single-side Panamax Bulk Carrier in hogging and sagging conditions. The Smith’s method is adopted and implemented into Beam Finite Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the cross section and three-cargo-hold model. As …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

Discrete Power Control In Heterogenous Networks, Yuanyuan Wang, Wibowo Hardjawana, Branka Vucetic

Makara Journal of Technology

In heterogeneous networks (HetNets) where femtocell base stations (FBSs) are deployed within the radio coverage of macrocell base stations (MBSs) to increase network capacity, co-channel interference limits overall system performance with universal frequency reuse. This paper investigates new distributed downlink discrete power control scheme for FBSs in HetNets with FBSs cooperation. The objective of the proposed power control scheme is to maximize the number of simultaneous FBSs transmissions in a single transmission wireless channel where each FBS is allowed to transmit only if the signal-to-interference-noise ratio (SINR) requirements for both FBSs and MBS users are satisfied. We apply a stochastic …

Multi-Project Scheduling Cost Optimization In A Machine Manufacturer Engineer-To-Order, Farizal Farizal, Amar Rachman, Tifani Tandean, Sumarsono Sudarto, Katsuhiko Takahashi

Makara Journal of Technology

This paper discusses the utilization of mixed integer linear programming (MILP) model to optimize cost for multiproject scheduling in a machine maker company. The objective is to minimize total project’s penalty cost and labor cost. The model formulated shows how to achieve the objective i.e. whether to use outsourcing or overtime to finish all projects. The model of multi-project scheduling was solved by Branch & Bound algorithm coded in Lingo 14.0 software. The case study shows that if a company wants to minimize lateness, it should use overtime instead of outsourcing, which minimize total lateness of projects by 144 days …