Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2016

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 301 - 330 of 768

Full-Text Articles in Materials Science and Engineering

Photoelectrochemical Water Splitting Cells: Methods For Improving Performance Of Electrodes And Recent Progress On Photocathodes, Kai-Jian Zhu, Wen-Jun Luo, Zhong-Jie Guan, Xin Wen, Zhi-Gang Zou, Wei Huang Aug 2016

Photoelectrochemical Water Splitting Cells: Methods For Improving Performance Of Electrodes And Recent Progress On Photocathodes, Kai-Jian Zhu, Wen-Jun Luo, Zhong-Jie Guan, Xin Wen, Zhi-Gang Zou, Wei Huang

Journal of Electrochemistry

Photoelectrochemical water splitting can convert solar energy into hydrogen which is an ideal way to utilize and store solar energy. A p-n tandem cell is considered as the most promising solar water splitting cell due to its high theory conversion efficiency, low cost and photoelectrode material flexibility. However, solar conversion efficiency of a tandem cell is still low in the experiment because of poor performance in a single photoelectrode. In this review, we have introduced some effective approaches to improve the performances of photoelectrodes by reducing recombination of photogenerated carriers in the bulk or on the surface, and suppressing back …

Go to article

Theoretical Study Of Photoelectrochemical Reactions And Ec-Sers On Spr Metallic Electrodes Of Silver And Gold, Yuan-Fei Wu, Ran Pang, Meng Zhang, Jian-Zhang Zhou, Bin Ren, Zhong-Qun Tian, De-Yin Wu Aug 2016

Theoretical Study Of Photoelectrochemical Reactions And Ec-Sers On Spr Metallic Electrodes Of Silver And Gold, Yuan-Fei Wu, Ran Pang, Meng Zhang, Jian-Zhang Zhou, Bin Ren, Zhong-Qun Tian, De-Yin Wu

Journal of Electrochemistry

At present photoelectrochemistry has received much concern back to nanostructures of noble metals from semiconductor electrodes. This is due to the surface plasmon resonance (SPR) effect of metallic nanostructures, which can effectively convert the far-field light to the near-field light and concentrate the photonic energy to the local surface area with high energy density. Thus, the different enhancement mechanisms, such as the local optical field enhancement, the formation of light generated hot carriers (hot electron-hole pairs), or the photothermal effect, have been proposed in literatures. On the basis of the SPR enhancement effect, the surface-enhanced Raman spectroscopy (SERS) can be …

Go to article

Preparations And Photoelectrochemical Properties Of Phosphate Modified Rgo-Biobr Nanocomposites, Shuang-Ying Chen, Zhi-Jun Li, Xu-Liang Zhang, Kang Hu, Rui Yan, Li-Qiang Jing Aug 2016

Preparations And Photoelectrochemical Properties Of Phosphate Modified Rgo-Biobr Nanocomposites, Shuang-Ying Chen, Zhi-Jun Li, Xu-Liang Zhang, Kang Hu, Rui Yan, Li-Qiang Jing

Journal of Electrochemistry

The RGO-BiOBr nanocomposites have been successfully synthesized by a hydrothermal process, and then modified with phosphorous acids. The photoelectrochemical properties of the fabricated RGO-BiOBr nanocomposite films were studied. The results indicate that the photocurrent densities of RGO-BiOBr were much larger compared with those of the bare BiOBr, and interestingly, the photocurrent densities were further improved after phosphate modification. Based on the analyses of the produced hydroxyl radical amounts, the enhanced photocurrent densities could be attributed to the introduction of RGO and to the formed negative fields of modified phosphate groups, which are favorable for electrons to be transferred and for …

Go to article

Activation Effect Of Nano-Carbon Derived From Co2 On Lead Electrode In Sulfuric Aqueous Solution, Yu-Qiao Song, Hua Zhu, Guang-Jin Zhao, Wen-Long Wu, Shou-Bin Zhou, Di-Hua Wang Aug 2016

Activation Effect Of Nano-Carbon Derived From Co2 On Lead Electrode In Sulfuric Aqueous Solution, Yu-Qiao Song, Hua Zhu, Guang-Jin Zhao, Wen-Long Wu, Shou-Bin Zhou, Di-Hua Wang

Journal of Electrochemistry

Serious sulfation of the negative plate is one of the most popular reasons of the early failure of lead-acid battery. Addition of nano-carbon was proved to be effective for recovering the sulfated electrode and the property of the carbon material always plays an important role. In this work, a new kind of nano-carbon material with high electrical conductivity and good adsorption capability for heavy metal cations, which is electrochemically prepared from CO2 in molten carbonates, was tested as activation additive for the sulfated lead electrode by cyclic voltammetry and SEM measurements. The results showed that the as-prepared carbon can …

Go to article

WoX/Pedot:Pss Double-Layered Hole-Transport Layers For Efficient And Stable Planar Heterojunction Perovskite Solar Cells, Wen-Yuan Qiao, Qiang Guo, Cong Li, Shuang Ma, Fu-Zhi Wang, Song-Yuan Dai, Zhan-Ao Tan Aug 2016

WoX/Pedot:Pss Double-Layered Hole-Transport Layers For Efficient And Stable Planar Heterojunction Perovskite Solar Cells, Wen-Yuan Qiao, Qiang Guo, Cong Li, Shuang Ma, Fu-Zhi Wang, Song-Yuan Dai, Zhan-Ao Tan

Journal of Electrochemistry

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a commonly used hole-transport material in the perovskite solar cells (PerSCs) structure of perovskite/fullerene planer heterojunction, but it also has a negative effect on the stability of device because of its acidity which will corrode metal oxide transparent electrodes. In this work, a WOx hole-transport layer with high work function was inserted into the PEDOT: PSS and FTO to enhance the stability and photovoltaic performance. The inserted WOx layer not only can avoid direct contact between PEDOT:PSS and FTO, but also can further reduce the contact barrier between the electrode interface. We studied the effect …

Go to article

A Novel Flexible Dye-Sensitized Solar Cell Based On Pt Networks Counter Electrode, Zi-Jie Xu, Fa-Yin Zhang, Xiao-Dan Hong, Wen-Xi Guo, Xiang-Yang Liu, Chang-Jian Lin Aug 2016

A Novel Flexible Dye-Sensitized Solar Cell Based On Pt Networks Counter Electrode, Zi-Jie Xu, Fa-Yin Zhang, Xiao-Dan Hong, Wen-Xi Guo, Xiang-Yang Liu, Chang-Jian Lin

Journal of Electrochemistry

Flexible dye-sensitized solar cells (DSSCs) have received widespread attentions in recent years because of their ease of fabrication, low production cost, relatively high chemical stability and flexibility. We report the fabrication of ZnO DSSCs based on the highly flexible, conducting, catalytic and transparent Pt networks counter electrode, and the performance of this solar cell was characterized by SEM, XRD, polarized fluorescence microscope, motor, I-V test station and electrochemical workstation. Compared to Pt nanofiber arrays (NFs), Pt networks not only show a better conductivity, but also exhibit superior transparency and catalytic activity. Furthermore, Pt networks electrode could be constructed on arbitrary …

Go to article

Silk As A Biomaterial Paste For Biomimetic Composite, Sang Hyun Park Aug 2016

Silk As A Biomaterial Paste For Biomimetic Composite, Sang Hyun Park

McKelvey School of Engineering Graduate Student Theses & Dissertations

Silk is a highly promising biomaterial with unique bio-physicochemical properties, such as excellent mechanical and optical properties, biocompatibility and programmable biodegradability. Among many different types, silk from domesticated silkworm, bombyx mori has received wide attention owing to its availability in virtually unlimited quantities and ease of extraction. In this study, we investigated silkworm silk as a protein glue to realize nacre-like composites. We have employed spin assisted layer-by-layer technique to fabricate ultrathin free-standing biocomposite films. Two different composites have been studied: (i) graphene oxide (GO)/silk and (ii) chitin/silk. From our prior work, it is known that the adsorption of amphiphilic …

Go to article

Nonaffine Rearrangements Of Atoms In Deformed And Quiescent Binary Glasses, Nikolai V. Priezjev Aug 2016

Nonaffine Rearrangements Of Atoms In Deformed And Quiescent Binary Glasses, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The influence of periodic shear deformation on nonaffine atomic displacements in an amorphous solid is examined via molecular dynamics simulations. We study the three-dimensional Kob-Andersen binary mixture model at a finite temperature. It is found that when the material is periodically strained, most of the atoms undergo repetitive nonaffine displacements with amplitudes that are broadly distributed. We show that particles with large amplitudes of nonaffine displacements are organized into compact clusters. With increasing strain amplitude, spatial correlations of nonaffine displacements become increasingly long-ranged, although they remain present even in a quiescent system due to thermal fluctuations.

Go to article

Properties Of Partially Stabilized Zirconia Components Fabricated By The Ceramic On-Demand Extrusion Process, Wenbin Li, Amir Ghazanfari, Devin Mcmillen, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts Aug 2016

Properties Of Partially Stabilized Zirconia Components Fabricated By The Ceramic On-Demand Extrusion Process, Wenbin Li, Amir Ghazanfari, Devin Mcmillen, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Ceramic On-Demand Extrusion (CODE) process is a novel additive manufacturing process for fabricating dense ceramic components from aqueous pastes of high solids loading. In this study, 3 mol% Y2O3 stabilized tetragonal zirconia polycrystal (3Y-TZP) parts were fabricated using the CODE process. The parts were then dried in a humidity controlled environmental chamber and sintered under atmospheric pressure. Mechanical properties of the sintered parts were examined using ASTM standard test techniques, including density, Young’s modulus, flexural strength, Weibull modulus, fracture toughness and Vickers hardness. The microstructure was analyzed, and grain size was measured using scanning electron microscopy. …

Go to article

3d Printing Of A Polymer Bioactive Glass Composite For Bone Repair, Caroline Murphy, Krishna C. R. Kolan, M. Long, Ming-Chuan Leu, Julie A. Semon, D. E. Day Aug 2016

3d Printing Of A Polymer Bioactive Glass Composite For Bone Repair, Caroline Murphy, Krishna C. R. Kolan, M. Long, Ming-Chuan Leu, Julie A. Semon, D. E. Day

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A major limitation of synthetic bone repair is insufficient vascularization of the interior region of the scaffold. In this study, we investigated the 3D printing of adipose derived mesenchymal stem cells (AD-MSCs) with polycaprolactone (PCL)/bioactive glass composite in a single process. This offered a three-dimensional environment for complex and dynamic interactions that govern the cell’s behavior in vivo. Borate based bioactive (13-93B3) glass of different concentrations (10 to 50 weight %) was added to a mixture of PCL and organic solvent to make an extrudable paste. AD-MSCs suspended in Matrigel was extruded as droplets using a second syringe. Scaffolds measuring …

Go to article

Powders For Additive Manufacturing Processes: Characterization Techniques And Effects On Part Properties, Austin T. Sutton, Caitlin S. Kriewall, Ming-Chuan Leu, Joseph William Newkirk Aug 2016

Powders For Additive Manufacturing Processes: Characterization Techniques And Effects On Part Properties, Austin T. Sutton, Caitlin S. Kriewall, Ming-Chuan Leu, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed based Additive Manufacturing is a class of Additive Manufacturing (AM) processes that bond successive layers of powder by laser melting to facilitate the creation of parts with complex geometries. As AM technology transitions from the fabrication of prototypes to end-use parts, the understanding of the powder properties needed to reliably produce parts of acceptable quality becomes critical. Consequently, this has led to the use of powder characterization techniques such as scanning electron microscopy (SEM), laser light diffraction, x-ray photoelectron spectroscopy (XPS), and differential thermal analysis (DTA) to both qualitatively and quantitatively study the effect of powder characteristics on part …

Go to article

Designed Extrudate For Additive Manufacturing Of Zirconium Diboride By Ceramic On-Demand Extrusion, Devin Mcmillen, Wenbin Li, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts Aug 2016

Designed Extrudate For Additive Manufacturing Of Zirconium Diboride By Ceramic On-Demand Extrusion, Devin Mcmillen, Wenbin Li, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work describes a process by which zirconium diboride (ZrB2) parts may be fabricated using the Ceramic On-Demand Extrusion (CODE) process. An oxide-carbide-nitride system consisting of ceramic powders and pre-ceramic organics, designed to yield ZrB2 after reaction sintering, has been developed to produce an aqueous-based extrudate for subsequent processing in the CODE system. Pressurelessly sintered test specimens containing 1 wt% PVA binder achieve high relative density ≥ 99%. The viscoelastic response of the extrudate was characterized via spindle rheometry with a small sample adapter. Batches with 1 wt% PVA and 0.5 wt% Methocel show strong shear thinning characteristic, under …

Go to article

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas Aug 2016

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Go to article

Simulation Of Cooling Rate Effects On Ti-48al-2cr-2nb Crack Formation In Direct Laser Deposition, Lei Yan, Wei Li, Xueyang Chen, Yunlu Zhang, Joseph William Newkirk, Frank W. Liou, David Dietrich Aug 2016

Simulation Of Cooling Rate Effects On Ti-48al-2cr-2nb Crack Formation In Direct Laser Deposition, Lei Yan, Wei Li, Xueyang Chen, Yunlu Zhang, Joseph William Newkirk, Frank W. Liou, David Dietrich

Materials Science and Engineering Faculty Research & Creative Works

Transient temperature history is vital in direct laser deposition (DLD) because it reveals the cooling rate at specific temperatures, which directly relates to phase transformation and types of microstructure formed in deposit. FEA simulation was employed to study the transient temperature history and cooling rate at different experimental setups in Ti-48Al-2Cr-2Nb DLD process. In this paper, an innovative model was described, which combines a moving Gaussian distribution heat source and element birth and death technology in ANSYS, help to analysis cooling rate control method and guide crack-free deposits build process.

Go to article

Modeling And Experimental Investigation Of Pre-Mixed Multi-Powder Flow In Fabricating Functional Gradient Material By Laser Metal Deposition Process, Wei Li, Jingwei Zhang, Sreekar Karnati, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, W. L. Seufzer Aug 2016

Modeling And Experimental Investigation Of Pre-Mixed Multi-Powder Flow In Fabricating Functional Gradient Material By Laser Metal Deposition Process, Wei Li, Jingwei Zhang, Sreekar Karnati, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, W. L. Seufzer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal Deposition (LMD) is an effective process to fabricate Functionally Graded Material (FGM) from pre-mixed powders. Since the supplied multi-powder directly affects the deposited FGM’s composition, investigation on Pre-Mixed Multi-Powder (PMMP) flow during LMD is greatly needed. This paper presents a comprehensive numerical PMMP flow model. By solving discrete particle force balance equations coupled with continuity equations and momentum equations for carrier gas, the dynamic behavior of PMMP flow through powder feeder tube and out of nozzle was calculated. With this model, the particle sizes of multi-powder were optimized to obtain considered FGM composition. To verify the modeling results, …

Go to article

Elevated Temperature Microstructure Stability Of Slm 304l Stainless Steel, Tarak Amine, Joseph William Newkirk Aug 2016

Elevated Temperature Microstructure Stability Of Slm 304l Stainless Steel, Tarak Amine, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

With time at temperature, changes in metallurgical structure can be expected for almost any steel or alloy. In stainless steels, the changes can be grain growth, carbide precipitation, ferrite decomposition, or embrittlement. These phenomena can significantly effect the properties of the steel and would potentially change the functionality of the component. Therefore, to determine component stability, the elevated temperature microstructure stability of additive manufacturing materials was studied. This work investigates the influence of different aging times of additive material stainless steels (304L) fabricated with the Selective Laser Melting (SLM) process on microstructure and mechanical properties. Microstructure and mechanical properties were …

Go to article

Investigation Of Tensile Properties Of Bulk And Slm Fabricated 304l Stainless Steel Using Various Gage Length Specimens, Sreekar Karnati, I. Axelsen, Frank W. Liou, Joseph William Newkirk Aug 2016

Investigation Of Tensile Properties Of Bulk And Slm Fabricated 304l Stainless Steel Using Various Gage Length Specimens, Sreekar Karnati, I. Axelsen, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The complex solidification dynamics and thermal cycling during Selective Laser Melting process is expected to result in non-equilibrium material characteristics. There is an essential need for characterization techniques which are critical towards the estimation of anisotropies. The current investigation is targeted towards establishing tensile testing methodologies and their relation to differing gage lengths. Dog-bone shaped specimen designs with gage lengths of 1”, 0.3” and 0.12” were employed in this research. The characterization was performed on hot rolled-annealed 304 stainless and SLM fabricated 304L stainless. It was theorized that smaller gage length specimens would be instrumental in mapping material property anisotropy …

Go to article

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas Aug 2016

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (< 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Go to article

Investigation Of Heat-Affected 304l Ss Powder And Its Effect On Built Parts In Selective Laser Melting, Caitlin S. Kriewall, Austin T. Sutton, Ming-Chuan Leu, Joseph William Newkirk, Ben Brown Aug 2016

Investigation Of Heat-Affected 304l Ss Powder And Its Effect On Built Parts In Selective Laser Melting, Caitlin S. Kriewall, Austin T. Sutton, Ming-Chuan Leu, Joseph William Newkirk, Ben Brown

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective laser melting (SLM) is a powder bed based additive manufacturing process in which a layer of powder is laid over the surface of a substrate and a laser with sufficient energy is employed to selectively melt particles to build a part layer by layer. During the SLM process, dark smoke was observed coming off of the powder bed surface where the laser was interacting with powder. This phenomenon resulted from heat-affected powder that was visibly different than the base powder. Since the concentration of the heat-affected powder differs throughout the build chamber as a result of the recirculating argon …

Go to article

Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk Aug 2016

Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct Laser Metal Deposition (LMD) was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. Scanning electron microscopy (SEM), optical microscopy (OM) and energy dispersive spectroscopy (EDS) were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. X-ray diffraction (XRD) was used for the phase identification. After significant analysis, some differences were observed among …

Go to article

Proposed Hybrid Processes For Part Building Using Fusion Welding And Friction Stir Processing, Megan A. Gegesky, Frank W. Liou, Joseph William Newkirk Aug 2016

Proposed Hybrid Processes For Part Building Using Fusion Welding And Friction Stir Processing, Megan A. Gegesky, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It has been shown that a hybrid laser additive manufacturing and friction stir processing can deposit components with forged-like structures. This paper reports a hybrid fusion welding and friction stir process to create parts with quality structures. Combining traditional fusion welding and friction stir processing techniques for non-weldable aluminum alloys could facilitate the joining of difficult geometries in manufactured parts. This research illustrates mechanical property changes for non-weldable and weldable aluminum alloys. The Vickers hardness, and microhardness in the case of AA5052-H32, tensile strength and corrosion resistance of four processing states: base material, fusion welded material, friction stir welded material, …

Go to article

Design Maps For Fracture Resistant Functionally Graded Materials, Muhammad Ridwan Murshed Aug 2016

Design Maps For Fracture Resistant Functionally Graded Materials, Muhammad Ridwan Murshed

Theses and Dissertations

The objective of this research is to generate design maps to identify functionally graded microstructures with enhanced fracture toughness. Several Functionally Graded Materials (FGMs) with an edge crack and membrane loading are considered and the resulting J-integral values are computed numerically using Finite Element Analysis. In order to capture the resulting stress fields accurately, Barsoum elements are used in the vicinity of the crack tip and the simulations are carried out for several crack lengths (a) and material contrasts (κ). The averages of the J-integral values are used to determine the normalized Stress Intensity Factors which are then benchmarked with …

Go to article

Amine-Thiol Solution Route Method For Fabricating Cdxzn1-Xs Thin Film Solar Cells, Preston D. Fernandez, Xianyi Hu, Carol Handwerker, Rakesh Agrawal Aug 2016

Amine-Thiol Solution Route Method For Fabricating Cdxzn1-Xs Thin Film Solar Cells, Preston D. Fernandez, Xianyi Hu, Carol Handwerker, Rakesh Agrawal

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cadmium zinc sulfide, CdZnS, is a promising material for the buffer layer of thin film solar cells because the alloy is considerably more cost effective and more optimizable than pure cadmium sulfide, CdS, in terms of band gap. The current fabrication methods of the buffer layer often require expensive equipment or produce undesirable impurities in the alloy. This study investigates a cost effective and scalable solution route method to synthesize the CdZnS buffer layer. Molecular precursors of CdZnS were dissolved in varying molecular ratios of cadmium and zinc in a mixture of hexylamine and propanethiol. The resulting alloys produced were …

Go to article

Radiation Tailored Polymers For Detectors, Adhesive-Coatings And Other Industrial Uses, Anna M. Earley, Alex Bakken, Rusi P. Taleyarkhan Aug 2016

Radiation Tailored Polymers For Detectors, Adhesive-Coatings And Other Industrial Uses, Anna M. Earley, Alex Bakken, Rusi P. Taleyarkhan

The Summer Undergraduate Research Fellowship (SURF) Symposium

The ever growing importance of humans to depend on renewable resources has shifted the focus of consumers, producers, and even politicians to more sustainable answers. Furthermore, pressure on the oil and natural gas industry has elevated the status of biopolymers in this regard. Polylactic acid (PLA) is unique polymer that offers unique abilities for tailored property derivation; thereby, enabling one to replace many engineered polymers and provide a sustainable solution as a nontoxic renewable resource. As a bioplastic, the tailoring of PLA under various conditions is important to the application and integration into current industry uses. After irradiating high molecular …

Go to article

Study Of Oxidative-Crosslink Reaction In Polyphenyl Sulfide (Pps) / Carbon Fiber And Its Influence In Additive Manufacturing, Dong Hee Kim, Eduardo Barocio, Bastian Brenken, Anthony Favaloro, Byron Pipes Aug 2016

Study Of Oxidative-Crosslink Reaction In Polyphenyl Sulfide (Pps) / Carbon Fiber And Its Influence In Additive Manufacturing, Dong Hee Kim, Eduardo Barocio, Bastian Brenken, Anthony Favaloro, Byron Pipes

The Summer Undergraduate Research Fellowship (SURF) Symposium

Ever since its development in 1980s, Fused Filament Fabrication (FFF) has been an attractive additive manufacturing technology due to its flexibility to create intricate shapes at lower costs and faster manufacturing process than subtractive techniques. These advantages make FFF suitable for printing molds for use in traditional composites manufacturing processes. Combining FFF with high-temperature thermoplastic composites enables producing molds that not only sustain autoclave conditions but also have low coefficient of thermal expansion (CTE). A semi-crystalline polymer, Poly-phenylene Sulfide (PPS), with 50% by weight of carbon fiber is used as feedstock material for FFF. Nonetheless, PPS is sensitive to undergo …

Go to article

Wearable Piezotronic Devices For Heart Rate Monitoring, Adam J. Miller, Wenzhuo Wu Dr. Aug 2016

Wearable Piezotronic Devices For Heart Rate Monitoring, Adam J. Miller, Wenzhuo Wu Dr.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Self-powered multifunctional wearable devices that are capable of human-device interfacing are highly desired. Piezotronic devices utilize piezoelectricity and semiconductor properties to enable devices to have seamless interaction between human and device. One important use for piezotronic devices is for pressure sensing. Pressure sensing devices have been employed in smart skins, biomonitoring, gesture recognition, and many more applications. This study aims to create a flexible piezotronic device, specifically for use in pressure sensing to monitor heart rate. ZnO nanowires are grown on a flexible polymer substrate so that they can be made into wearable devices. A p-n heterojunction is formed by …

Go to article

Development Of A New Nanohub Simulation Tool: Coarse Graining Of Crystalline Nano-Cellulose., Kuo Tian, Mehdi Shishehbor, Pablo Zavattieri Aug 2016

Development Of A New Nanohub Simulation Tool: Coarse Graining Of Crystalline Nano-Cellulose., Kuo Tian, Mehdi Shishehbor, Pablo Zavattieri

The Summer Undergraduate Research Fellowship (SURF) Symposium

Crystalline Nano-cellulose (CNC) is a general molecular structure obtained from acid hydrolysis of native fiber. They are often very short (100 to 1000 manometers) and the mechanical properties of CNC varies depend on length scale. Due to defect formation of the structure, the mechanical properties of the material composed of such CNC may vary drastically. This study was to provide a numerical tool to integrate a few valid modules and to better understand the mechanical properties of CNC and the overall performance of the bio-inspired material composed of CNC. Our focus is mainly on two type of composite structure [1] …

Go to article

Photonicstd-2d: Modeling Light Scattering In Periodic Multilayer Photonic Structures, Alexey Bondarev, Shaimaa Azzam, Zhaxylyk Kudyshev, Alexander V. Kildishev Aug 2016

Photonicstd-2d: Modeling Light Scattering In Periodic Multilayer Photonic Structures, Alexey Bondarev, Shaimaa Azzam, Zhaxylyk Kudyshev, Alexander V. Kildishev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Efficient modeling of electromagnetic processes in optical and plasmonic metamaterials is important for enabling new and exciting ways to manipulate light for advanced applications. In this work, we put together a tool for numerical simulation of propagation of normally incident light through a nanostructured multilayer composite material. The user builds a unit cell of a given material layer-by-layer starting from a substrate up to a superstrate, splitting each layer further into segments. The segments are defined by width and material -- dielectric, metal or active medium. Simulations are performed with the finite difference time domain (FDTD) method. A database of …

Go to article

Evaluation Of Strain Distortion Correction Protocol Using Scanning Electron Microscopy And Digital Image Correlation, Alexandra Mallory, Alberto Mello, Michael Sangid Aug 2016

Evaluation Of Strain Distortion Correction Protocol Using Scanning Electron Microscopy And Digital Image Correlation, Alexandra Mallory, Alberto Mello, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Scanning electron microscopy in combination with digital image correlation (SEM-DIC) is a useful technique for measuring strain in materials at the micro-scale. In particular, it can be used to identify micro-scale strain localizations that are the precursor to material failure. While SEM produces high resolution images of the microstructure, the images also contain a large amount of distortion that, during DIC, will result in distorted strain values that require correction. In this project, a nickel-based alloy underwent cyclic mechanical fatigue at three different high temperatures to a targeted maximum strain. Scanning electron microscopy imaging was done on a 200x150μm area …

Go to article

Characterizing Hmx/Ap Cocrystal Propellant Through Planar Laser Induced Fluorescence, Seth M. Nielsen, Michael S. Powell, Steven F. Son Aug 2016

Characterizing Hmx/Ap Cocrystal Propellant Through Planar Laser Induced Fluorescence, Seth M. Nielsen, Michael S. Powell, Steven F. Son

The Summer Undergraduate Research Fellowship (SURF) Symposium

Energetic cocrystals, or energetic materials that consist of two or more components that form a unique crystalline structure with unique properties, are currently being investigated as a possible method for decreasing the sensitivity of high energy density explosives for use in powerful solid composite propellants. Fuels more powerful than those in current use have not been practical because of their increased safety hazard due to higher sensitivity to being ignited. This has been one of the barriers that has prevented solid composite propellants from seeing significant improvements in performance. This study is an attempt to characterize a cocrystal of HMX …

Go to article

First Prev Next Last