Materials Science and Engineering Commons^™

Zno Nanosheet Arrays Constructed On Weaved Titanium Wire For Cds-Sensitized Solar Cells, Cuncun Wu, Lin Wei, Yitan Li, Chang Liu, Jun Jiao, Yanxue Chen, Liangmo Mei

Mechanical and Materials Engineering Faculty Publications and Presentations

Ordered ZnO nanosheet arrays were grown on weaved titanium wires by a low-temperature hydrothermal method. CdS nanoparticles were deposited onto the ZnO nanosheet arrays using the successive ionic layer adsorption and reaction method to make a photoanode. Nanoparticle-sensitized solar cells were assembled using these CdS/ZnO nanostructured photoanodes, and their photovoltaic performance was studied systematically. The best light-to-electricity conversion efficiency was obtained to be 2.17% under 100 mW/cm/cm² illumination, and a remarkable shortcircuit photocurrent density of approximately 20.1 mA/cm² was recorded, which could attribute to the relatively direct pathways for transportation of electrons provided by ZnO nanosheet arrays as …

[M3(Μ3-O)(O2cr)6] And Related Trigonal Prisms: Versatile Molecular Building Blocks For 2-Step Crystal Engineering Of Functional Metal-Organic Materials, Alexander Schoedel

USF Tampa Graduate Theses and Dissertations

Metal-organic materials (MOMs) assembled from metal-based building blocks and organic linkers have attracted much interest due to their large pore dimensions and their enormous structural diversity. In comparison to their inorganic counterparts (zeolites), these crystalline materials can be easily modified to tailor pore dimensions and functionality for specifically targeted properties.

The work presented herein encompasses the development of a synthetic 2-step process for the construction of novel families of MOMs or 'platforms' and allow us exquisite design and control over the resulting network topologies. Examples of cationic mesoporous structures were initially exploited, containing carboxylate based centers connected by metal-pyridine bonds. …

Cds Quantum Dot-Sensitized Solar Cells Based On Nano-Branched Tio2 Arrays, Chang Liu, Yitan Li, Lin Wei, Cuncun Wu, Yanxue Chen, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

Nano-branched rutile TiO2 nanorod arrays were grown on F:SnO2 conductive glass (FTO) by a facile, two-step wet chemical synthesis process at low temperature. The length of the nanobranches was tailored by controlling the growth time, after which CdS quantum dots were deposited on the nano-branched TiO2 arrays using the successive ionic layer adsorption and reaction method to make a photoanode for quantum dot-sensitized solar cells (QDSCs). The photovoltaic properties of the CdS-sensitized nano-branched TiO2 solar cells were studied systematically. A short-circuit current intensity of approximately 7 mA/cm2 and a light-to-electricity conversion efficiency of 0.95% were recorded for cells based on …

Identification Of Silver And Palladium In Irradiated Triso Coated Particles Of The Agr-1 Experiment, I. J. Van Rooyen, T. M. Lillo, Y. Q. Wu

Materials Science and Engineering Faculty Publications and Presentations

Evidence of the release of certain metallic fission products through intact tristructural isotropic (TRISO) particles has been seen for decades around the world, as well as in the recent AGR-1 experiment at the Idaho National Laboratory (INL). However, understanding the basic mechanism of transport is still lacking. This understanding is important because the TRISO coating is part of the high temperature gas-cooled reactor functional containment and critical for the safety strategy for licensing purposes.

Our approach to identify fission products in irradiated AGR-1 TRISO fuel using scanning transmission electron microscopy (STEM), Electron Energy-Loss Spectroscopy (EELS) and Energy Filtered TEM (EFTEM), …

Investigation Of Degradation Effects Due To Gate Stress In Gan-On-Si High Electron Mobility Transistors Through Analysis Of Low Frequency Noise, Michael Curtis Meyer Masuda

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMT) have superior performance characteristics compared to Silicon (Si) and Gallium Arsenide (GaAs) based transistors. GaN is a wide bandgap semiconductor which allows it to operate at higher breakdown voltages and power. Unlike traditional semiconductor devices, the GaN HEMT channel region is undoped and relies on the piezoelectric effect created at the GaN and Aluminum Gallium Nitride (AlGaN) heterojunction to create a conduction channel in the form of a quantum well known as the two dimensional electron gas (2DEG). Because the GaN HEMTs are undoped, these devices have higher electron mobility crucial for …

Corrosion-Resistant Glasses For Steel Enamels, Richard K. Brow, Signo Tadeu Dos Reis, Michael L. Koenigstein, Genda Chen

Materials Science and Engineering Faculty Research & Creative Works

A cementitious composite material wherein glass-coated steel rods are positioned in a cementitious matrix. The glass composition for coating the steel reinforcing rods includes between about 33-45 weight percent SiO₂, 13.5-19.5 weight percent B₂O₃, 3.5-4.6 weight percent Al₂O₃, 4.0-13.5 weight percent K₂O, 5.5-15.5 weight percent ZrO₂, 8.6-15.9 weight percent Na₂O, 4.6-5.1 weight percent CaO, 0.6-0.7 weight percent MnO₂, 1.0-1.0 weight percent NiO, and 1.0-1.1 weight percent CoO. The glass composition is typically in compression on the rods at ambient temperatures, has a …

Structural Study Of Na2o-Feo-Fe2o3-P 2o5 Glasses By High-Pressure Liquid Chromatography, Lina Ma, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Three series of Na₂O-FeO-Fe₂O₃-P₂O₅ glasses with compositional ranges of 3.25 < O/P < 3.5 and 0 < Fe/P < 0.67 were prepared. Glass structure was studied using high-pressure liquid chromatography (HPLC). The average chain-length of phosphate anions decreases with increasing O/P ratios and glasses with similar O/P ratios and greater Fe/P ratios have wider distributions of phosphate anion lengths due to disproportionation reactions in the glass melts. © 2013 Elsevier B.V.

Triplet Ground State Of The Neutral Oxygen-Vacancy Donor In Rutile Tio2, A. T. Brant, Eric M. Golden, Nancy C. Giles, Shan Yang, M. A. R. Sarker, S. Watauchi, M. Nagao, I. Tanaka, D. A. Tryk, A. Manivannan, Larry E. Halliburton

Faculty Publications

Electron paramagnetic resonance (EPR) is used to investigate the triplet (S = 1) ground state of the neutral oxygen vacancy in bulk rutile TiO₂ crystals. This shallow donor consists of an oxygen vacancy with two nearest-neighbor, exchange-coupled ³⁺ ions located along the [001] direction and equidistant from the vacancy. The spins of the two trapped electrons, one at each ³⁺ ion, align parallel to give the S = 1 state. These neutral oxygen vacancies are formed near 25 K in as-grown oxidized TiO₂ crystals by illuminating with sub-band-gap 442 nm laser light. The angular dependence of the EPR …

Pulse Electrodeposition Of Pd-Ni Alloy Nanoparticles For Electrocatalytic Oxidation Of Formic Acid, Fang-Zu Yang, Jun-Pei Yue, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

The Pd-Ni alloy nanoparticles with nickel atomic contents of 12.0%, 16.4% and 22.6% were successfully electrodeposited from a Pd-Ni alloy electrolyte by square wave pulse plating. The alloy nanoparticles were in the spherical shape with a diameter of 50 ~ 80 nm. As the growth potential of the alloy was negatively shifted, the nickel content of the alloy was increased, and the size of the nanoparticles was almost the same, whereas the number, the degree of crosslinking and the real active area of the nanoparticles were increased. As the nickel content of the alloy nanoparticles increased, the peak current for …

Fabrication And Impedance Performance Of Gradient Lani0.6Fe0.4O3-δ-Gd0.2Ce0.8O2 Composite Cathodes For Intermediate Temperature Solid Oxide Fuel Cell, Yang Li, Bo Huang, Meng Yuan, Zhi-Qiu Zhang, Zong-Yao Liu, Xu-Chen Tang, Xin-Jian Zhu

Journal of Electrochemistry

A LNF-GDC composite cathode with a gradual change in the composition between ScSZ electrolyte and LNF cathode was fabricated to reduce the cathode polarization resistance (R_p). The gradual change in composition between ScSZ electrolyte and LNF cathode shows the decreases in the charge transfer resistance (R_ct) and gas phase diffusion resistance (R_d). The results revealed that the Rp value, measuring 0.452 Ω·cm² at 750 °C, was the lowest for LNF-GDC composite cathodes with three layers and gradient changes in composition between ScSZ and LNF (Cathode C),, whereas the Rp value of 70%LNF-30%GDC composite …

Electrochemical Performance Of Si-C Composites Prepared By Discharge-Plasma Assisted Milling, Yu-Long Chen, Ren-Zong Hu, Hui Liu, Wei Sun, Min Zhu

Journal of Electrochemistry

Silicon-carbon (Si-C) composites, with microstructure of multi-scaled Si particles being homogenously dispersed in micro-sized carbon matrix, had been prepared by dielectric barrier discharge plasma assisted two-step milling for the first time. The Si-C composite anode had a discharge capacity of 1259 mAh·g^-1 at the first cycle, while the capacity retained 474 and 396 mAh·g^-1 after 20 and 100 cycles, respectively. Charge-discharge curves and AC impedance response indicated that both silicon and carbon phases in the composite anode were involved during the lithiation/delithiation reactions and the electron transport resistance in the Si-C composite anode was much lower than that …

Study On Carbon Supported Pd Catalysts Modified By Phosphomolybdic Acid For H2O2 Electrocatalytic Reduction, Li-Mei Sun, Cheng Zhang, Ying-Rong Bao, Hong-Xia Li

Journal of Electrochemistry

The Pd/C catalyst was prepared with the chemical reduction method, and phosphomolybdic acid (PMA) was modified on the Pd/C catalyst using the dipping method. The compositions and structures of the Pd/C and Pd/C modified by phosphomolybdic acid (PMA-Pd/C) catalysts were characterized with X-ray diffraction and Fourier Transform infrared spectroscopy analyses. The electrocatalytic activity and stability of the catalysts for the reduction of hydrogen peroxide (H₂O₂) were studied using cyclic voltammetry and chronoamperometry. The results showed that the phosphomolybdic acid was tightly fixed on the surface of Pd/C catalyst through the chemical interaction. The eletrocatalytic activity of …

Design And Development Of A Novel Glucose Biosensor Based On The Ferrocene-Functionalized Fe3O4 Nanoparticles/Carbon Nanotubes/Chitosan Nanocomposite Film Modified Electrode, Hua-Ping Peng, Dai-Jun Zha, Wei Chen, Ai-Lin Liu, Xin-Hua Lin

Journal of Electrochemistry

A novel platform for the fabrication of glucose biosensor was successfully constructed by entrapping glucose oxidase (GOD) in a ferrocene monocarboxylic acid-aminated Fe₃O₄ magnetic nanoparticles conjugate (FMC-AFNPs)/chitosan (CS)/multiwall carbon nanotubes (MWNTs) nanocomposite. The formation of FMC-AFNPs could effectively prevent the leakage of ferrocene and retain its electrochemical activity. This GOD/FMC-AFNPs/CS/MWNTs matrix provided a biocompatible microenvironment for retaining the native activity of the immobilized GOD. Moreover, the presence of MWNTs enhanced the charge-transport properties of the composite and facilitated electron transfer between the GOD and the electrode for the electrocatalysis of glucose. Under the optimal conditions the designed …

Preparation Of High Performance Porous Silicon Powders By Etching Al-Si Alloy In Acid Solution For Lithium Ion Battery, Shi-Ji Hao, Chun-Li Li, Kai Zhu, Ping Zhang, Zhi-Yu Jiang

Journal of Electrochemistry

Porous silicon powders prepared by etching Al-Si alloy using an acid solution was reported in the first time. The morphology and structure of as-obtained material were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD) method. It was found that the spongy porous silicon powders presented well crystalline structure and consisted of nano-Si particles. The particle size of porous Si powders was about 20 μm, and the specific surface area was 102.7 m²·g^-1. The electrochemical properties of porous silicon powders were evaluated as an anode material for lithium ion batteries. The material proportion in the …

Preliminary Study On Morphology Controllability Of Electrochemically Prepared Polyaniline By Using Aniline Aimer, Yang Zuo, Kang Shi

Journal of Electrochemistry

Employing of aniline dimer (N-phenyl-p-phenylenediamine, NPD) as the starting monomer, polyaniline was electrochemically synthesized on the surface of glassy carbon electrode in acetonitrile-aqueous mixing solutions（20% by volume）containing 1 mol·L^-1 HClO₄. Experimental results demonstrated that the polymerization of NPD occurs at the potentials about 0.2 V lower than those of aniline monomer. Furthermore, the resulting polyaniline has higher morphology controllability than those synthesized by using aniline as the stating monomer. The uniform polyaniline nanoparticles (30 nm in diameter), ultralong nanowires (length > 5 μm, 50 nm in diameter) or large area nanosheets (4 μm in length, 2 μm in …

Synthesis And Electrochemical Properties Of Lico1-XMgXMno4 And Lico1-XAlXMno4 (X= 0, 0.02, 0.05, 0.1) As Positive Materials For Lithium-Ion Batteries, Mei-Ling You, Qing-Song Tong, Xiu-Hua Li, Min Lin, Xing-Kang Huang, Yong Yang

Journal of Electrochemistry

The Al-doped and Mg-doped LiCoMnO₄ materials were synthesized through solid-state reaction. The effects of doping amounts of Mg and Al on the initial capacities, discharge plateaus, and cycle performances were investigated. The morphologies and structures of the as-prepared materials were studied by scanning electron microscopy and powder X-ray diffraction. The results indicate that the as-prepared samples were composed of uniform, well-crystallized particles. The pristine LiCoMnO₄ possessed an initial capacity of 87.0 mAh·g^-1, while LiCo_0.98Mg_0.02MnO₄ and LiCo_0.98Al_0.02MnO₄ delivered 91.3 and 93.6 mAh·g^-1, respectively. The proper …

Passivation Behavior Of Aluminum Alloy During Electrochemical Machining And Its Effects On The Machining Performance, Li-Min Jiang, Wen-Bo Deng, Jun-Long Ying

Journal of Electrochemistry

The passivation behavior of aluminum alloy during electrochemical machining was investigated and discussed. The effects of processing voltage, current density, space of electrodes and electrolyte composition on electrochemical machining performance were explored. The results indicate that the electrochemical machining aluminum alloy in the composite electrolyte system containing NaNO₃ and NaF existed passivation phenomenon. Passivation action decreaseed the current efficiency and made it varied greatly with the current density. Also the passivation shifted the interspace characteristic curve of electrode notably to a negative direction. There was not passivation phenomenon in the composite electrolyte system containing the same concentrations of NaCl …

Electrochemical Oxidation Of Ammonium Nitrite In Absorption Solution Of Flue Gas, Yong-Hong Lu, Xiao-Bo Dong, Li-Sha Wang, Yan Liu, Chen-Jian Zhu, Hai-Bo Xu

Journal of Electrochemistry

In order to make full uses of ammonium nitrite in absorption solution from flue gas simultaneous desulfurization, denitrification and demercurization processes, here the electrochemical oxidation method was used to transform ammonium nitrite into ammonium nitrate. By using polarization curve, cyclic voltammogram and galvanostatic methods, suitable electrode materials were evaluated and chosen. The influence of electrolyte composition was discussed and the appropriate process parameters were obtained. Finally, the effect of electrochemical oxidation was confirmed by chemical analysis method. In 0.05 mol·L^-1 NaNO₂ + 0.05 mol·L^-1 (NH₄)₂SO₄ simulated absorption solution (5 L, pH = …

Preparation Of Pd/Tio2/C Catalyst And Its Electrocatalytic Performance In Basic Solution For Ethanol Oxidation, Qiao-Xia Li, Yi-Chao Yang, Ming-Shuang Liu, Hong-Min Mao, Qun-Jie Xu

Journal of Electrochemistry

Nanoparticles TiO₂ were prepared by hydrothermal method using precursor tetrabutyl titanate. The Pd/TiO₂/C catalyst was synthesized by liquid phase reducing method supported on nano TiO₂ and Vulcan carbon XC-72. The Pd/TiO₂/C catalyst was characterized by XRD, TEM, cyclic voltammetry, and chronopotentiometry. XRD confirmed the face-centered cubic structure of Pd particles, and TEM indicated that Pd particles (size 3 ~ 4 nm) dispersed uniformly on TiO₂ and carbon XC-72. The results from cyclic voltammogram and chronopotentiogram showed the higher ethanol oxidation activity and stability of Pd/TiO₂/C catalyst (20% Pd) as compared with …

A Systematic Study Of The Optical And Electrical Properties Of Ge1-YSnY And Ge1-X-YSiXSnY Semiconductor Alloys, Thomas R. Harris

Theses and Dissertations

In order to fully utilize newly developed Ge_1-ySn_y and Ge_1-x-ySi_xSn_y materials for new novel optoelectronic devices, the optical and electrical properties of these alloys were investigated using photoluminescence (PL) and Hall-effect measurements. Direct bandgap PL emission was observed from almost all the samples, making them very promising candidates for Si-based light emitting devices. T-dependent PL studies also indicate that the indirect-to-direct bandgap transition of Ge_1-ySn_y alloys might take place at a much lower Sn content than the theory predicts. T-dependent Hall-effect measurements showed both degenerate parallel conducting layers as …

Tunneling Into The Mott Insulator Sr2Iro4, John A. Nichols, Noah Bray-Ali, Armin Ansary, Gang Cao, Kwok-Wai Ng

Center for Advanced Materials Faculty Publications

We studied the single-layered iridate Sr₂IrO₄ with a scanning tunneling microscope. The finite low temperature conductance enables the electronic structure of this antiferromagnetic Mott insulator to be measured by tunneling spectroscopy. We imaged the topography of freshly cleaved surfaces and measured differential tunneling conductance at cryogenic temperatures. We found the Mott gap in the tunneling density of states to be 2Δ=615 meV. Within the Mott gap, additional shoulders are observed which are interpreted as inelastic loss features due to magnons.

Mechanical Properties Of Components Fabricated With Open-Source 3-D Printers Under Realistic Environmental Conditions, B. M. Tymrak, M Kreiger, Joshua M. Pearce

Department of Materials Science and Engineering Publications

he recent development of the RepRap, an open-source self-replicating rapid prototyper, has made 3-D polymer-based printers readily available to the public at low costs ( < $500). The resultant uptake of 3-D printing technology enables for the first time mass-scale distributed digital manufacturing. RepRap variants currently fabricate objects primarily from acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA), which have melting temperatures low enough to use in melt extrusion outside of a dedicated facility, while high enough for prints to retain their shape at average use temperatures. In order for RepRap printed parts to be useful for engineering applications the mechanical properties of printed parts must be known. This study quantifies the basic tensile strength and elastic modulus of printed components using realistic environmental conditions for standard users of a selection of open-source 3-D printers. The results find average tensile strengths of 28.5 MPa for ABS and 56.6 MPa for PLA with average elastic moduli of 1807 MPa for ABS and 3368 MPa for PLA. It is clear from these results that parts printed from tuned, low-cost, open-source RepRap 3-D printers can be considered as mechanically functional in tensile applications as those from commercial vendors.

The Structure And Properties Of Zinc Aluminophosphate Glasses, Charmayne E. Smith (Lonergan), Richard K. Brow, Lionel Montagne, Bertrand Revel

Materials Science and Engineering Faculty Research & Creative Works

The glass forming region of the ZnO-Al₂O₃-P₂O₅ (ZAP) system was determined and the structures and properties of the glasses were characterized. For glasses with a constant O/P ratio, i.e., with similar average phosphate anion distributions, and with increasing alumina content, there is an increase in molar volume and glass transition temperature and a decrease in density and refractive index. The structures of the ZAP glasses were characterized by Raman spectroscopy, ³¹P and ²⁷Al magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy, and high pressure liquid chromatography (HPLC). Systematically shorter phosphate …

Compounds And Methods For Reducing Oxidative Stress, Thomas Dziubla, J. Zach Hilt, Dipti Biswal, David B. Cochran, Paritosh Wattamwar

Chemical and Materials Engineering Faculty Patents

Antioxidant polymeric compounds are provided that comprise a plurality of monomeric portions, where each monomeric portion includes an antioxidant molecule interposed between at least two acrylate molecules, and where at least one acrylate molecule of each monomeric portion is linked by a diamine molecule to an acrylate molecule of an adjacent monomeric portion to thereby form the polymer. Methods of synthesizing polymeric compounds and methods of using the antioxidant polymeric compounds to reduce oxidative stress are also provided.

Nanostructured Dielectric Materials For High Energy Density Multilayer Ceramic Capacitors, Fatih Dogan, Alan Devoe, Ian Burns

Materials Science and Engineering Faculty Research & Creative Works

A multilayer ceramic capacitor, having a plurality of electrode layers and a plurality of substantially titanium dioxide dielectric layers, wherein each respective titanium dioxide dielectric layer is substantially free of porosity, wherein each respective substantially titanium dioxide dielectric layer is positioned between two respective electrode layers, wherein each respective substantially titanium dioxide dielectric layer has an average grain size of between about 200 and about 400 nanometers, wherein each respective substantially titanium dioxide dielectric layer has maximum particle size of less than about 500 nanometers. Typically, each respective substantially titanium dioxide dielectric layer further includes at least one dopant selected …

Nanostructured Dielectric Materials For High Energy Density Multilayer Ceramic Capacitors, Fatih Dogan, Alan Devoe, Ian Burn

Materials Science and Engineering Faculty Research & Creative Works

A multilayer ceramic capacitor, having a plurality of electrode layers and a plurality of substantially titanium dioxide dielectric layers, wherein each respective titanium dioxide dielectric layer is substantially free of porosity, wherein each respective substantially titanium dioxide dielectric layer is positioned between two respective electrode layers, wherein each respective substantially titanium dioxide dielectric layer has an average grain size of between about 200 and about 400 nanometers, wherein each respective substantially titanium dioxide dielectric layer has maximum particle size of less than about 500 nanometers. Typically, each respective substantially titanium dioxide dielectric layer further includes at least one dopant selected …

Electronic Structure Characterization Of Hybrid Materials, Zhi Li

USF Tampa Graduate Theses and Dissertations

In this dissertation, the studies aim to characterize the electronic structure at the internal interface of hybrid materials. The characterization challenge is originating from the spectral superposition of hybrid constituents. A characterization protocol based on photoemission spectroscopy (PES) was developed and applied to investigate the orbital alignment at the internal interface of the oligothiophene-TiO2 and ArS-CdSe hybrid materials by characterizing the individual constituents and the assembly hybrids respectively. Electrospray deposition technique was used to deposit targeting materials which enabled preparation of thin films in vacuum minimizing ambient contaminations while transmission electron microscopy (TEM) was used to investigate the morphology and …

Large-Scale Solution Synthesis Of Narrow Graphene Nanoribbons, Timothy H. Vo, Mikhail Shekhirev, Donna A. Kunkel, Martha D. Morton, Eric Berglund, Lingmei Kong, Peter M. Wilson, Peter A. Dowben, Axel Enders, Alexander Sinitskii

Nebraska Center for Materials and Nanoscience: Faculty Publications

According to theoretical studies, narrow graphene nanoribbons with atomically precise armchair edges and widths of(1.1 eV), which makes them potentially promising for logic applications. Different top–down fabrication approaches typically yield ribbons with width >10nm and have limited control over their edge structure. Here we demonstrate a novel bottom–up approach that yields gram quantities of high-aspect-ratio graphene nanoribbons, which are only ~1 nm wide and have atomically smooth armchair edges. These ribbons are shown to have a large electronic bandgap of ~1.3 eV, which is significantly higher than any value reported so far in experimental studies of graphene nanoribbons prepared by …

Effect Of Temperature On Tunneling And Quantum Efficiency In Cigs Solar Cells, Sizhan Liu

Theses

Utilizing the two-band approximation and Wentzel-Kramers-B ri l l oui n (WKB) approximation, by including the temperature-dependent effective masses and nonparabolicity effects, an investigation of the temperature dependent band-to-band tunneling process is discussed. In comparison with the parabolic approximation and non- parabolic approximation, the tunneling probability is strongly dependent on the non-parabolicity factor. The temperature dependence of the energy band gap, electron effective mass and light hole effective mass is investigated. The tunneling current density function is derived by a series representation of the incomplete gamma function with non-parabolic effect and its variation at low temperature is also investigated. When …

Analysis Of Transport Properties In A Zaz Graphene Nanoribbon Junction Using Various Dopants, Natasha Parikh

Theses

A 12 atom wide ZAZ Graphene Junction was simulated and its transport properties were analyzed. I-V curves, calculated by nonequilibrium Greens function method combined with the density functional theory under external bias, showed varying semiconducting characteristics. Further, the width of the junction also showed significant effects in the determination of the semiconducting nature. A theoretical study was performed on the semiconducting characteristics by analyzing the I-V curve and transport coefficients in the junction.