Materials Science and Engineering Commons^™

Microstructure And Magnetic Properties Of Bulk Nanocrystalline Mnal, Anurag Chaturvedi, Rumana Yaqub, Ian Baker

Dartmouth Scholarship

MnAl is a promising rare-earth free permanent magnet for technological use. We have examined the effects of consolidation by back-pressure, assisted equal channel angular extrusion processing on mechanically-milled, gas-atomized Mn-46% at. Al powder. X-ray diffraction showed both that the extruded rod consisted mostly of metastable τ phase, with some of the equilibrium γ₂ and β phases, and that it largely retained the as-milled nanostructure. Magnetic measurements show a coercivity of ≤4.4 kOe and a magnetization at 10 kOe of ≤40 emu/g. In addition, extrusions exhibit greater than 95% of the theoretical density. This study opens a new window in …

Jamming Rheology Of Model Cementitious Suspensions Composed Of Comb-Polymer Stabilized Magnesium Oxide Particles, Lisa R. Murray, Kendra Erk

School of Materials Engineering Faculty Publications

The colloidal microstructure of concentrated suspensions containing anionic comb- polymer-stabilized magnesium oxide (MgO) particles in water was analyzed by shear rheometry for indications of changes in particle microstructure based on particle size and comb-polymer usage. As the suspensions were sheared at different rates, jamming in the sheared MgO suspensions was observed as shear stress overshoots. The shear-induced evolution of the suspension’s microstructure was strongly related to the perceived interactions between neighboring MgO particles in the suspension. In the jammed state, interactions are believed to be enhanced by the formation of entanglements between opposing comb-polymer side-chains. Steric repulsion between side-chains was …

Dynamical Heterogeneity In Periodically Deformed Polymer Glasses, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The dynamics of structural relaxation in a model polymer glass subject to spatially homogeneous, time-periodic shear deformation is investigated using molecular dynamics simulations. We study a coarse-grained bead-spring model of short polymer chains below the glass transition temperature. It is found that at small strain amplitudes, the segmental dynamics is nearly reversible over about 104 cycles, while at strain amplitudes above a few percent, polymer chains become fully relaxed after a hundred cycles. At the critical strain amplitude, the transition from slow to fast relaxation dynamics is associated with the largest number of dynamically correlated monomers as indicated by the …

Electronic Properties Of Inp (001)/Hfo2 (001) Interface: Band Offsets And Oxygen Dependence, Santosh Kc

Faculty Publications

Using ab-initio methods, atomic structures and electronic properties of InP (001)/HfO2 (001) interface are studied within the framework of density functional theory. We examine the InP/HfO2 model interface electronic structures under varying oxidation conditions. The effects of indium and phosphorous concentrations on interfacial bonding, defect states, band offsets, and the thermodynamic stability at the interface are also investigated. The origin of interfacial gap states in InP (001)/HfO2 (001) interface are proposed, mainly from the P-rich oxides, which is validated by our experimental work. This highlights the importance of surface passivation prior to high-κ deposition based on the in situ spectroscopic …

Development Of Precipitation Hardenable Al-Sc-Zr-Hf Quaternary Alloys Through Thermodynamic Modeling, And Room-Temperature And Elevated Temperature Hardness, Matthew J. Wong

Dissertations, Master's Theses and Master's Reports - Open

Aluminum alloyed with small atomic fractions of Sc, Zr, and Hf has been shown to exhibit high temperature microstructural stability that may improve high temperature mechanical behavior. These quaternary alloys were designed using thermodynamic modeling to increase the volume fraction of precipitated tri-aluminide phases to improve thermal stability. When aged during a multi-step, isochronal heat treatment, two compositions showed a secondary room-temperature hardness peak up to 700 MPa at 450°C. Elevated temperature hardness profiles also indicated an increase in hardness from 200-300°C, attributed to the precipitation of Al₃Sc, however, no secondary hardness response was observed from the Al …

Semi Conducting Polymer Assisted Separation Of Semiconducting Carbon Nanotubes For High Efficiency Hybrid Photovoltaics, Huiliang Evan Wang

Link Foundation Energy Fellowship Reports

The works reported here demonstrate that we can tune the purity, yield and bandgap of sorted semiconducting carbon nanotube by applying various solvents, polymers, carbon nanotube types and sorting procedure. As a result, the final solar cell performances can be enhanced. The research leads to both better fundamental understanding on sorting of carbon nanotubes by conjugated polymers as well as their engineering applications in solar cell devices. The technology of sorting semiconducting SWNTs with conjugated polymer will not only lead to better SWNT based solar cells but also lead to their applications in a range of other solution-processed electronic devices …

Spectroscopy Studies Of Straincompensated Mid-Infrared Qcl Active Regions On Misoriented Substrates, Gregory Edward Triplett, Justin Grayer, Charles Meyer, Emily Cheng, Denzil Roberts

Electrical and Computer Engineering Publications

In this work, we perform spectroscopic studies of AlGaAs/InGaAs quantum cascade laser structures that demonstrate frequency mixing using strain-compensated active regions. Using a three-quantum well design based on diagonal transitions, we incorporate strain in the active region using single and double well configurations on various surface planes (100) and (111). We observe the influence of piezoelectric properties in molecular beam epitaxy grown structures, where the addition of indium in the GaAs matrix increases the band bending in between injector regions and demonstrates a strong dependence on process conditions that include sample preparation, deposition rates, mole fraction, and enhanced surface diffusion …

Orientation-Dependent Pseudomorphic Growth Of Inas For Use In Lattice-Mismatched Mid-Infrared Photonic Structures, Gregory Edward Triplett, Charles Meyer, Emily Cheng

Electrical and Computer Engineering Publications

In this study, InAs was deposited on GaAs (100) and GaAs (111)B 2 degrees towardssubstrates for the purpose of differentiating the InAs growth mode stemming from strain and then analyzed using in-situ reflection high energy electron diffraction, scanning electron microscopy, Raman spectroscopy, reflectance spectroscopy, and atomic force microscopy. The procession of InAs deposition throughout a range of deposition conditions results in assorted forms of strain relief revealing that, despite lattice mismatch for InAs on GaAs (approximately 7%), InAs does not necessarily result in typical quantum dot/wire formation on (111) surfaces, but instead proceeds two-dimensionally due primarily to the surface orientation.

Organic Ferroelectric Evaporator With Substrate Cooling And In Situ Transport Capabilities, Keith Foreman, C. Labedz, M. Shearer, Shireen Adenwalla

Shireen Adenwalla Papers

We report on the design, operation, and performance of a thermal evaporation chamber capable of evaporating organic thin films. Organic thin films are employed in a diverse range of devices and can provide insight into fundamental physical phenomena. However, growing organic thin films is often challenging and requires very specific deposition parameters. The chamber presented here is capable of cooling sample substrates to temperatures below 130 K and allows for the detachment of the sample from the cooling stage and in situ transport. This permits the use of multiple deposition techniques in separate, but connected, deposition chambers without breaking vacuum …

Dynamic Materials And Devices For Controlling Solar Heat Gain In Buildings, David Alie

Electronic Theses and Dissertations

Modern technology and materials science, coupled with an understanding of our energy consumption patterns, allows for the opportunity to realize large-scale energy savings through the implementation of more efficient, adaptive technologies. More efficient heating and cooling of both commercial and residential buildings is a strong candidate for such advancements. Indeed, a significant portion of the annual US energy budget is devoted to the heating, ventilation, and air conditioning (HVAC) of commercial and residential buildings in order to maintain safe, comfortable internal environments.

Dynamic tint windows, both traditional electrochromic devices and reflective devices, are promising candidates to help in the effort …

Aging Of A Polymer Core Composite Conductor Under Combined Ozone And Temperature Conditions, James M. Middleton

Electronic Theses and Dissertations

The next generation High Temperature Low Sag Polymer Core Composite Conductors (HTLS PCCC) can experience harsh in-service environments including high temperature and highly concentrated ozone. In some extreme cases, it is possible that the conductors will experience temperatures of up to 180°C and ozone concentrations as high as 1% (10,000 ppm). Therefore, the primary goal of this research was to determine the most damaging aging conditions which could negatively affect the in-service life of the conductors. This included characterizing the aging in ozone and at high temperature of the HTLS PCCC hybrid composite rods and neat resin. It was found …

Degradation Of High Voltage Glass Fiber-Reinforced Polymer Matrix Composites By Aggressive Environmental Conditions, Tianyi Lu

Electronic Theses and Dissertations

Polymer matrix composites reinforced with either E glass or ECR glass fibers-reinforced are used in a variety of high voltage electrical applications because of their advantages like lower weight and cost. However, they can be damaged by aggressive in-service conditions such as high temperature, ultraviolet radiation, moisture, ozone and corrosive environments. Different degradation mechanisms can develop in high voltage PMCs under those extreme environments, which, in turn, can affect the long term structural durability of the composites. A set of PMCs reinforced with ECR-glass and E-glass fibers embedded in four different resins has been investigated in this study. In addition, …

Energy And Cost Saving Of A Photovoltaic-Phase Change Materials (Pv-Pcm) System Through Temperature Regulation And Performance Enhancement Of Photovoltaics, Ahmad Hasan, Sarah Mccormack, Ming Jun Huang

Articles

The current research seeks to maintain high photovoltaic (PV) efficiency and increased operating PV life by maintaining them at a lower temperature. Solid-liquid phase change materials (PCM) are integrated into PV panels to absorb excess heat by latent heat absorption mechanism and regulate PV temperature. Electrical and thermal energy efficiency analysis of PV-PCM systems is conducted to evaluate their effectiveness in two different climates. Finally costs incurred due to inclusion of PCM into PV system and the resulting benefits are discussed in this paper. The results show that such systems are financially viable in higher temperature and higher solar radiation …

Development And Application Of Biomimetic Electrospun Nanofibers In Total Joint Replacement, Wei Song

Wayne State University Dissertations

Failure of osseointegration (direct anchorage of an implant by bone formation at the bone-implant surface) and implant infection (such as that caused by Staphylococcus aureus, S. aureus) are the two main causes of implant failure and loosening. There is a critical need for orthopedic implants that promote rapid osseointegration and prevent bacterial colonization, particularly when placed in bone compromised by disease or physiology of the patients. A better understanding of the key factors that influence cell fate decisions at the bone-implant interface is required. Our study is to develop a class of "bone-like" nanofibers (NFs) that promote osseointegration while preventing …

Study Of Tin-Based Electrodes And Ionic Liquid Electrolytes For Energy Storage Materials, Mahbuba Ara

Wayne State University Dissertations

Due to rapid increase in energy demand, modern society necessitates to develop high power, light-weight, and more economical energy storage systems. Rechargeable Li-ion batteries and Li-oxygen batteries have become the most promising energy devices in terms of energy and power densities. Diverse research on these battery components is being carried out by researchers worldwide to improve power density to meet the future requirements. The possible routes to improving power density of Li-ion as well as Li-oxygen batteries is to use nanostructured, hybrid electrode materials since they can significantly enhance kinetics of electrochemical reactions; and ion-conducting, low volatile electrolytes since they …

Introduction To Special Issue Of Journal Of Defense Modeling And Simulation: Novel Approaches To Defense And Military Modeling And Simulation, Scott D. Snyder, James M. Taylor Jr.

Peter Kiewit Institute: Faculty Publications

Developing solutions to complex problems in government and industry is a daunting task that often requires tremendous investment in time and resources to solve. Modeling and simulation (M&S) has incredible potential to streamline development and cut costs by conducting virtual experiments that give insight into performance under various test conditions. As many program managers in the federal acquisition process can attest, realistic testing of live equipment in an operational environment can be some of the most expensive parts of a development program. M&S can provide insight into mission success of yetto- bedesigned systems without the need to actually build and …

Simple Multi-Attribute Rating Technique For Renewable Energy Deployment Decisions (Smart Redd), James M. Taylor Jr., Betty Love

Peter Kiewit Institute: Faculty Publications

In the effort to provide electrical power service and the sustaining fuel required to run generators at forward-deployed bases in Afghanistan and Iraq over more than 10 years, the United States military spent billions of dollars and a paid a heavy toll in terms of human casualties. The green energy linear program for optimizing deployments (GELPOD) proof-of-concept model showed that a linear program could be used to optimize combat deployment of energy generation systems to minimize cost and casualties. Results indicated that reduction in both cost and casualties for renewable energy sources was highly dependent on fuel cost and deployment …

Design, Synthesis And Applications Of Fluorescent And Electrochemical Probes, Giri K. Vegesna

Dissertations, Master's Theses and Master's Reports - Open

“Seeing is believing” the proverb well suits for fluorescent imaging probes. Since we can selectively and sensitively visualize small biomolecules, organelles such as lysosomes, neutral molecules, metal ions, anions through cellular imaging, fluorescent probes can help shed light on the physiological and pathophysiological path ways. Since these biomolecules are produced in low concentrations in the biochemical pathways, general analytical techniques either fail to detect or are not sensitive enough to differentiate the relative concentrations. During my Ph.D. study, I exploited synthetic organic techniques to design and synthesize fluorescent probes with desirable properties such as high water solubility, high sensitivity and …

Practical Aspects Of Modern And Future Permanent Magnets, R.W. Mccallum, L. H. Lewis, Ralph Skomski, M. J. Kramer, I. E. Anderson

Ralph Skomski Publications

The mandate to reduce greenhouse gases will require highly efficient electric machines for both power generation and traction motor applications. Although permanent magnet electric machines utilizing Nd2Fe14B-based magnets provide obvious power-to-weight advantages over induction machines, the limited availability and high price of the rare earth (RE) metals make these machines less favorable. Of particular concern is the cost and supply criticality of Dy, a key RE element that is required to improve the high-temperature performance of Nd-based magnetic alloys for use in generators and traction motors. Alternatives to RE-based alloys do exist, but they currently lack the energy density necessary …

Stock Aggregation Model And Virtual Archetype For Large Scale Retrofit Modelling Of Local Authority Housing In Ireland, James Pittam, Paul D. O’Sullivan, Garrett O’Sullivan

Conference Papers

Developing representative archetypes using a bottom up approach for stock modelling is an excellent tool for evaluating the overall performance of the building stock; however it requires detailed analysis of the various building types. Currently there is no detailed housing data base for Local Authority housing in Cork City, Ireland that catalogues the housing stocks geometric properties and thermal characteristics for each typology. This study details a methodology to catalogue the LAH stock and build a detailed housing data base. The GIS web based mapping application Google Street View is used to identify 20 house typologies across 36 LAH developments; …

Continuous Ultra-Thin Mos2 Films Grown By Low-Temperature Physical Vapor Deposition, Christopher Muratore, Jianjun Hu, Baoming Wang, M. Amanul Haque, John E. Bultman, Michael L. Jespersen, Michael E. Mcconney, R. D. Naguy

Chemical and Materials Engineering Faculty Publications

Uniform growth of pristine two dimensional (2D) materials over large areas at lower temperatures without sacrifice of their unique physical properties is a critical pre-requisite for seamless integration of next-generation van der Waals heterostructures into functional devices. This Letter describes a vapor phasegrowth technique for precisely controlled synthesis of continuous, uniform molecular layers of MoS2 on silicon dioxide and highly oriented pyrolitic graphite substrates of over several square centimeters at 350 °C. Synthesis of few-layer MoS2 in this ultra-high vacuum physical vapor deposition process yieldsmaterials with key optical and electronic properties identical to exfoliated layers. The films are composed of …

A Study On The Effect Of Magnetic Field On The Corrosion Behavior Of Materials, Soundarya Pondichery

Material Science and Engineering Theses - Archive

Corrosion causes deterioration of a material due to its environment. Corrosion control has been one of the biggest challenges in most industries since many years. There are various notable and unknown factors that influence the rate of corrosion of a certain material/environment system. Magnetic fields and their driven effects on an electrochemical system has been recently gained interest. Various magnetic field driven forces occurring in an electrolyte have been reported during an electrochemical reaction. Lorentz force driven convection in the electrolyte, known as MHD effect and paramagnetic gradient forces are reported to be the most effective. This research studies the …

Interfacial Reaction Of Sn-Based Solder Joint In The Package System, Huandi Gu

Material Science and Engineering Theses - Archive

Now a day in electronic industry, as the trend of requiring smaller package size with better electronic performance, lead-free solder joints are always required to decrease their sizes. As a result, the reliability of smaller size solder joints has became a critical issue. The primary factor causing the reliability issue of lead-free solder joints is intermetallic compound (IMCs) formation which forming during soldering process and thermal aging process and can significantly affect the mechanical properties of solder joint. In this study, two different size solder joints with same composition (SAC305 with 96.5%Sn, 3.0Ag, 0.5%Cu) are subjected to isothermal aging treatment …

Characterization Of Tantalum Nitride Thin Films By Magnetron Sputtering, Anna Zaman

Material Science and Engineering Theses - Archive

Tantalum Nitride is chemically inert, oxidation resistant and hard. TaN finds its application as a protective coating on steel due to their excellent wear properties. It has become a very promising diffusion barrier material in Cu interconnect technology in microelectronics. TaN has not been analyzed as much as other transition metal nitrides like the TiN system because TaN exhibits various stable and metastable phases. The emergence of these phases and the different physical, chemical and mechanical properties depend on the growth technique and deposition conditions. TaN thin films were deposited using the magnetron PVD system in the SaNEL lab. The …

Surface Modification Of Iron And Aluminum By Electrolytic Plasma Processing, Adam J. Smith

Material Science and Engineering Dissertations - Archive

Electrolytic Plasma Processing (EPP) is an emerging, clean surface modification technology which is able to both clean and, depending on the circuit polarity, deposit either cationic or anionic species from an aqueous electrolyte. EPP offers several benefits including environmental cleanliness, high deposition rates, and a nanograined surface structure. The following work presents research conducted on EPP, including surface cleaning of Fe and deposition of Ni onto Fe and Al substrates. Investigations were made into the microstructure of the surface as well as the atomic compositions of the coating and coating/substrate interface. EPP cleaning was initially conducted in order to determine …

Plasmonic Nanostructures For Surface-Enhanced Raman Spectroscopy, Ruiqian Jiang

Material Science and Engineering Theses - Archive

In the last three decades, a large number of different plasmonic nanostructures have attracted much attention due to their unique optical properties. Those plasmonic nanostructures include nanoparticles, nanoholes and metal nanovoids. They have been widely utilized in optical devices and sensors.When the plasmonic nanostructures interact with the electromagnetic wave and their surface plasmon frequency match with the light frequency, the electrons in plasmonic nanostructures will resonate with the same oscillation as incident light. In this case, the plasmonic nanostructures can absorb light and enhance the light scattering. Therefore, the plasmonic nanostructures can be used as substrate for surface-enhanced Raman spectroscopy …

Environmental Degradation Of Nano Enhanced Polymers In Low Earth Orbit, Mohammed Jaradat

Electronic Theses and Dissertations

No abstract provided.

A Novel Injectable Borate Bioactive Glass Cement As An Antibiotic Delivery Vehicle For Treating Osteomyelitis, Hao Ding, Cunju Zhao, Xu Cui, Yifei Gu, Weitao Jia, M. N. Rahaman, Yang Wang, Wenhai Huang, Changqing Zhang

Materials Science and Engineering Faculty Research & Creative Works

Background: A novel injectable cement composed of chitosan-bonded borate bioactive glass (BG) particles was evaluated as a carrier for local delivery of vancomycin in the treatment of osteomyelitis in a rabbit tibial model. Materials and Methods: The setting time, injectability, and compressive strength of the borate BG cement, and the release profile of vancomycin from the cement were measured in vitro. The capacity of the vancomycin-loaded BG cement to eradicate methicillin-resistant Staphylococcus aureus (MRSA)-induced osteomyelitis in rabbit tibiae in vivo was evaluated and compared with that for a vancomycin-loaded calcium sulfate (CS) cement and for intravenous injection of vancomycin. Results: …

Effect Of Er Doping On The Structural And Magnetic Properties Of Cobalt-Ferrite, Sateesh Prathapani, M. Vinitha, Tanjore V. Jayaraman, D. Das

Department of Mechanical and Materials Engineering: Faculty Publications

Nanocrystalline particulates of Er doped cobalt-ferrites CoFe_(2–x)Er_xO₄ (0 ≤ x ≤ 0.04), were synthesized, using sol-gel assisted autocombustion method. Co-, Fe-, and Er- nitrates were the oxidizers, and malic acid served as a fuel and chelating agent. Calcination (400–600 °C for 4h) of the precursor powders was followed by sintering (1000 °C for 4 h) and structural and magnetic characterization. X-ray diffraction confirmed the formation of single phase of spinel for the compositions x = 0, 0.01, and 0.02; and for higher compositions an additional orthoferrite phase formed along with the spinel phase. …

Development And Application Of Improved Shotctrete Refractory For Aluminum Rotary Furnace Applications, James G. Hemrick, Angela Rodrigues-Schroer, Dominick Colavito, Jeffrey D. Smith, Kelley O'Hara

Materials Science and Engineering Faculty Research & Creative Works

Oak Ridge National Laboratory, in collaboration with refractory manufacturer Minteq International, Inc., academic partner Missouri University of Science and Technology and refractory end users have developed novel refractory systems and techniques to reduce energy consumption of refractory lined vessels. The objective of this U.S. DOE funded project was to address the need for innovative refractory compositions by developing novel gunnable refractory compositions for use in high temperature and high alkali environments. Developed materials utilized new aggregate materials, bond systems, protective coatings, and phase formation techniques. Under this project, materials were developed specifically for aluminum rotary dross furnace applications and a …