Materials Science and Engineering Commons^™

Response Of Plasma Facing Components In Tokamaks Due To Intense Energy Deposition Using Particle-In-Cell(Pic) Methods, Filippo Genco

Open Access Dissertations

Damage to plasma-facing components (PFC) due to various plasma instabilities is still a major concern for the successful development of fusion energy and represents a significant research obstacle in the community. It is of great importance to fully understand the behavior and lifetime expectancy of PFC under both low energy cycles during normal events and highly energetic events as disruptions, Edge-Localized Modes (ELM), Vertical Displacement Events (VDE), and Run-away electron (RE). The consequences of these high energetic dumps with energy fluxes ranging from 10 MJ/m2 up to 200 MJ/m2 applied in very short periods (0.1 to 5 ms) can be …

Solution To Certain Problems In The Failure Of Composite Structures, Jonathan Goodsell

Open Access Dissertations

The present work contains the solution of two problems in composite structures. In the first, an approximate elasticity solution for prediction of the displacement, stress and strain fields within the m-layer, symmetric and balanced angle-ply composite laminate of finite-width subjected anticlastic bending deformation is developed. The solution is shown to recover classical laminated plate theory predictions at interior regions of the laminate and thereby illustrates the boundary layer character of this interlaminar phenomenon. The results exhibit the anticipated response in congruence with the solutions for uniform axial extension and uniform temperature change, where divergence of the interlaminar shearing stress is …

Multiscale Modeling Of The Hierarchical Structure Of Cellulose Nanocrystals, Fernando Luis Dri

Open Access Dissertations

Cellulose constitutes the most abundant renewable polymeric resource available today. It considered an almost inexhaustible source of raw material, and holds great promise in meeting increasing demands for environmentally friendly and biocompatible products. Key future applications are currently under development for the automotive, aerospace and textile industries. When cellulose fibers are subjected to acid hydrolysis, the fibers yield rod-like, highly crystalline residues called cellulose nanocrystals (CNCs). These particles show remarkable mechanical and chemical properties (e.g. Young Modulus ~200 GPa) within the range of other synthetically-developed reinforcement materials. Critical to the design of these materials are fundamental material properties, many of …

Applicability Of Continuum Fracture Mechanics In Atomistic Systems, Shao-Huan Cheng

Open Access Dissertations

By quantitating the amplitude of the unbounded stress, the continuum fracture mechanics defines the stress intensity factor K to characterize the stress and displacement fields in the vicinity of the crack tip, thereby developing the relation between the stress singularity and surface energy (energy release rate G). This G-K relation, assigning physical meaning to the stress intensity factor, makes these two fracture parameters widely used in predicting the onset of crack propagation. However, due to the discrete nature of the atomistic structures without stress singularity, there might be discrepancy between the failure prediction and the reality of nanostructured materials. Defining …

Atomic Level Study Of Water-Gas Shift Catalysts Via Transmission Electron Microscopy And X-Ray Spectroscopy, Mehmed Cem Akatay

Open Access Dissertations

Water-gas shift (WGS), CO + H₂ O [Special characters omitted.] CO₂ + H₂ (ΔH° = -41 kJ mol ^-1 ), is an industrially important reaction for the production of high purity hydrogen. Commercial Cu/ZnO/Al₂ O₃ catalystsare employed to accelerate this reaction, yet these catalysts suffer from certain drawbacks, including costly regeneration processes and sulfur poisoning. Extensive research is focused on developing new catalysts to replace the current technology. Supported noble metals stand out as promising candidates, yet comprise intricate nanostructures complicating the understanding of their working mechanism.

In this study, the structure of the supported …

Microstructural Evolution And Mechanical Properties Of Friction Stir Welded Ods Alloy Ma754, Jiye Wang, Wei Yuan, Rajiv S. Mishra, Indrajit Charit

Materials Science and Engineering Faculty Research & Creative Works

Microstructural evolution and mechanical properties of MA754, an yttrium oxide dispersion-strengthened nickel-based superalloy, were investigated after friction stir welding (FSW). A tool rotation rate of 1000 revolution per minute and a traverse speed of 50.8 mm per minute were employed using a cermet (WC-Co) tool. After FSW, fine equiaxed grain structure with a high dislocation density and a random texture was achieved. Agglomeration of yttrium oxide dispersoids was observed in FSW MA754. Room-temperature tensile properties of FSW MA754 were compared to those of as-received MA754 alloy, and the results indicated that particle strengthening contribution decreased as a result of dispersoid …

Enhanced Reducibility And Conductivity Of Na/K-Doped Srti0.8Nb0.2O3, Guoliang Xiao, Sirikanda Nuansaeng, Lei Zhang, Suwit Suthirakun, Andreas Heyden, Hans-Conrad Zur Loye, Fanglin Chen

Faculty Publications

Donor and acceptor co-doped SrTiO₃ materials have shown interesting features in their conductivity and reducibility. In this work, 10 mol% Na⁺ or K⁺ as acceptor dopants have been introduced into the A-site of donor-doped strontium titanate, SrTi_0.8Nb_0.2O₃, and the doping impact on their properties has been studied. By doping with Na or K, the sinterability of SrTi_0.8Nb_0.2O₃ in reducing atmospheres has been improved. Na_0.1Sr_0.9Ti_0.8Nb_0.2O₃ and K_0.1Sr_0.9Ti_0.8Nb_0.2O₃ show metallic …

Wound Care, Steven B. Jung, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

A method for treating a wound, and a dressing for wound care management comprising a three-dimensional body of glass-based fibers comprising one or more glass-formers selected from the group consisting of P₂O5, SiO₂, and B₂O₃; at least about 25 wt % of the fibers have a diameter between about 200 nm and about 4000 nm, and a length:width aspect ratio of at least about 10. In another form, the glasses are in the form of particles in an ointment or cream applied to a wound. In yet other forms the glasses are …

Solid State Pre-Formed Electronics Adhesive (Spea), Alexander Randon Cope

Dissertations and Theses

In mobile and handheld consumer electronic markets, product use conditions drive the requirement for mechanical strength and device durability. The majority of relatively large form factor electronic components in a laptop, mobile internet device, PDA, or mobile phone use an adhesive as a stiffener to help protect the component from physical stresses imposed by daily wear and tear. Described herein is an innovative solution referred to as Solid State Pre-Formed Electronics Adhesive (SPEA), which enables a decrease in circuit board manufacturing throughput time while increasing mechanical durability with a consistent and characterized adhesive application process.

Today, many consumer electronic ODM's …

Additivity Of Strengthening Mechanisms In Ultrafine Grained Al-Mg-Sc Alloy, N. Kumar, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

In the light of unique and anomalous properties of ultrafine grained (UFG) alloys, an effort was made to develop a predictive capability of the yield strength (YS) of UFG Al-Mg-Sc alloy. UFG microstructure was introduced using friction stir processing. Microstructural characterization of grain size, dislocations, and nano-sized Al3(Sc,Zr) particles was carried out using electron backscatter diffraction and transmission electron microscope. The contribution from Peierls-Nabarro stress, solid solution strengthening, precipitation strengthening, grain boundary strengthening, and dislocation strengthening were assessed using existing strengthening models. Additivity law to predict the YS of the alloy was chosen based on the microstructural state of the …

Quantum Computing Circuits, Cheng-Hsiao Wu, Casey Andrew Cain

Electrical and Computer Engineering Faculty Research & Creative Works

A system for performing digital operations, including a first device configured to transform a digital input into one or more signals, at least one AB ring, the at least one AB ring irreducibly-coupled and configured to include at least three terminals, a second device configured to read a portion of a signal expressed upon two or more of the at least three terminals, and a third device configured to transform the portion of the signal expressed upon two or more of the at least three terminals into a digital output, the third device operationally connected to the second device.

Fabrication And Characterization Of A Palladium/Porous Silicon Layer, Nicholas Hong Lui

Master's Theses

When porous silicon is plated with a catalytic metal, the two materials can act together as a single entity whose electrical properties are sensitive to its environment – the sensing component of an electrochemical gas sensor. Etching pores into silicon is an electrochemical process; and which type of doped silicon used is one of its key parameters. For nearly all reported porous silicon gas sensors, the silicon has been of the p-doped variety – because p-doped porous etching is better understood and the layers that result from it are more predictable – despite n-doped silicon having potentially significant benefits in …

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …

Comment On "Giant Plasticity Of A Quantum Crystal", Caizhi Zhou, Charles J. Olson Reichhardt, Matthias J. Graf, Jungjung Su, Alexander V. Balatsky, Irene J. Beyerlein

Materials Science and Engineering Faculty Research & Creative Works

In their Letter, Haziot et al. report a novel phenomenon of giant plasticity for hcp ⁴He quantum crystals. They assert that ⁴He exhibits mechanical properties not found in classical plasticity theory. Specifically, they examine high-quality crystals as a function of temperature T and applied strain ϵ_app, where the shear modulus µ =T_app/ϵ_app reaches a plateau and dissipation 1=Q becomes close to zero; both quantities are reported to be independent of applied stress T_app and strain ϵ_app, implying a reversible dissipation process and suggesting dislocation motion by quantum tunneling. At lower …

Characterization Of Neural Ion Regulation Dysfunction During Insult And Evaluation Of Micro-Opioid Receptor Activation During Simulated Ischemia In The Pre-Botzinger Complex, Kyle F. Dobiszewski

Dissertations

The health and vitality of brain tissue is dependent upon the cells' abilities to maintain ionic homeostasis across their plasma membranes. Even slight alterations in intracellular or extracellular can have a devastating effect on excitability and neural vitality. This thesis investigates several concepts related to ion flux. First, it investigates how ion flux affects characterization of brain tissue by dielectric spectroscopy and what can be done to overcome that effect. Second, it investigates how ion flux can be used to describe the state of health of the tissue. Finally, it investigates if pharmacological intervention can attenuate some of the deleterious …

Electrosynthesis Of Glycerol Carbonate From Co2 And Glycerol, Huan Wang, Mei-Xia Zhu, La-Xia Wu, Xiao-Ming Xu, Xue-Ru Zhao, Jia-Xing Lu

Journal of Electrochemistry

Glycerol carbonate was obtained from glycerol and carbon dioxide under room temperature and normal pressure by electrochemical method. The effects of synthesis conditions, such as cathode, charge, current density and temperature, on the reaction of glycerol and carbon dioxide have been investigated. The yields of 73% were produced by electrosynthesis of carbonate under the optimized condition, which is much higher than that by common catalysis method. The electrochemical behavior of the reaction system has been studied by cyclic voltammetry, through which the reaction process has been proposed.

Influence Of Pretreatment On Electrocatalytic Property For Methanol Oxidation Of Ptru/Wc, Xiao-Ling Lang, Mei-Qin Shi, Ye-Kun Jiang, Chun-An Ma

Journal of Electrochemistry

The surface of tungsten carbide (WC) was treated by potassium hydroxide (KOH) at different pH values for different time. The PtRu/WC composite was prepared by microwave-assisted polyol method. The phase structure of PtRu/WC composites were characterized by XRD. The electrocatalytic activity was tested by cyclic voltammetry and chronoamperometry. The results indicated that with different pH treatments WC became more readily supported on PtRu. When treating WC in KOH at pH = 14, PtRu exhibited the best degree of crystallinity on WC surface, leading to the highest electrocatalytic activity of PtRu/WC. Moreover, the optimized activity of PtRu/WC towards methanol oxidation was …

Synthesis And Electrochemical Properties Of Li(Ni0.5Co0.2Mn0.3)1-2xTiXNbXO2, Yong Tang, Qin-Lin Liao, Xiang-An Guo

Journal of Electrochemistry

The cathode-active materials of layered Li(Ni_0.5Co_0.2Mn_0.3)_1-2xTi_xNb_xO₂（x=0, 0.002, 0.005, 0.01, 0.02）composites were synthesized by the thermal treatment of the coprecipitated precursor at 900 ^oC in air. The effects of Ti-Nb co-dopants on the structural and electrochemical properties of Li(Ni_0.5Co_0.2Mn_0.3)O₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical experiments. The results show that the small amounts of Ti-Nb co-dopants in Li(Ni_0.5Co_0.2Mn_0.3)O₂significantly decreased the degree of cation mixing in …

Effects Of Fluoroethylene Carbonate Additive On Low Temperature Performance Of Li-Ion Batteries, Feng-Ju Bian, Zhong-Ru Zhang, Yong Yang

Journal of Electrochemistry

The effects of fluoroethylene carbonate (FEC) on the low temperature performance of lithium ion phosphate full battery are evaluated by different techniques. By addition of 5 wt% FEC into a commercial electrolyte, effective solid electrolyte interface (SEI) film can be formed on the graphite electrodes, the discharge capacity retention at -40 ^oC was increased from 31.7% to 43.7%, and the discharge voltage plateau of the cell is raised. This is attributed to a reduced charge transfer resistance and a lowered polarization on the graphite electrode by electrochemical impedance spectroscopy (EIS) and reference electrode test.

Research Progress Of Intermediate Layers In Ti-Based Oxide Anodes, Xiu-Li Song, Hui-Min Yang, Zhen-Hai Liang

Journal of Electrochemistry

Titanium (Ti)-based oxide anodes are excellent anode materials which have been applied widely in electrochemical fields all over the world. Adding intermediate layers in Ti-based oxide anodes can improve the conductivity, lengthen the lifetime and strengthen the stability between Ti base and metal oxides active layers of electrodes. This article reviews the research progress of intermediate layers in Ti-based oxide anodes. At the same time, current problems existed in the field of Ti-based oxide anodes are pointed out and future development trend in oxide electrode with intermediate layers is prospected.

Advanced Treatment Of Dyeing Wastewater For Reuse By Electrochemical Oxidation, Fei-Xiang Chen, Chu-Yin Yang, Ming-Ming Zhou, Jia-De Wang

Journal of Electrochemistry

In response to the characteristics of dye wastewater, the electrochemical oxidation of effluents from the biochemical process of dyeing wastewater was studied in the electrochemical reactor using PbO₂/Ti electrode as the anode and stainless steel plate as the cathode. The results revealed that the electrochemical oxidation could simultaneously remove the Chemical Oxygen Demand (COD), ammonia and chromaticity. At the residence time of 60 min and current density of 10 mA·cm^-2, the COD, ammonia, chromaticity, concentration of chloride ion and pH values could meet the water standards for “the reuse of urban recycling water-water quality standard for …

Voltage Reversal Behavior In Microbial-Anode Fuel Cells, En-Ren Zhang, Jun-Le Niu, Lei Liu, Guo-Wang Diao

Journal of Electrochemistry

Voltage reversal behavior was investigated in microbial-anode fuel cells (MFCs). Electricity-producing biofilms were developed on the surface of anodes in MFCs inoculated with mixed inoculum from activated sludge. MFC duplicates generally exhibited different performances with respect to the internal resistance, the voltage output and the discharging duration when operating in batch mode. Voltage reversal was observed to occur first in the MFC with lower performance when connecting MFCs in series. Analysis of electrode potentials indicated that the potentials of microbial anodes quickly shifted to more positive values when enhancing discharge current, resulting in voltage reversal in MFCs. Increasing temperature would …

Using Hydrolyzed Sludge Liquor As The Substrate Of Microbial Fuel Cell, Peng Liang, Chao Guo, Xia Huang

Journal of Electrochemistry

Hydrolyzed sludge liquor was used as the substrate of microbial fuel cell. When the thermal treatment time increased from 2 h to 96 h, pH varied little between 7.4 and 8.0. When the treatment time increased, the conductivity, COD and alkaline condition increased to 2.53 mS·cm^-1, 2520 mg·L^-1 and 800 mg·L^-1, respectively. Meanwhile, the power density increased to 25 W·m^-3. The COD removal increased firstly, then decreased, and finally reached the maximum of 47% at the hydrolyzed time of 6 h. The maximal coulombic efficiency was 71% when the treatment time was 4 …

Electrochemically Switched Ion Exchange Properties Of Pani-Snp Composite Films In Wastewater Containing Ni2+ And Cd2+, Yan-Ting Feng, Jun-Qiang Xiao, Xiao-Gang Hao, Xu-Li Ma, Zhong-De Wang, Nian-Chen Han

Journal of Electrochemistry

Electroactive PANI-SnP composite films were prepared by drop-coating method on Pt electrodes and investigated as electrochemically switched ion exchange (ESIX) materials for the separation of Cd²⁺ from aqueous solutions. The composition and morphology of the composite film were characterized by Fourier transform infrared spectrometer (FTIR) and scanning electron microscope (SEM). In solutions containing 0.1 mol·L^-1 Ni(NO₃)₂ and Cd(NO₃)₂, cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM) were used to investigate the electrochemical behavior and ion-exchange mechanism of PANI-SnP composite film. The elementary composition of PANI-SnP composite films in both oxidation …

Graphene Quantum Dots Enhanced Electrochemical Performance Of Polypyrrole As Supercapacitor Electrode, Kun Wu, Si-Zhe Xu, Xue-Jiao Zhou, Hai-Xia Wu

Journal of Electrochemistry

With an objective to develop electrode materials with high specific capacitance and good stability, a completely new nanocomposite of Polypyrrole (PPY) and graphene quantum dots (GQD) was successfully obtained through in-situ polymerization of pyrrole in the presence of GQD suspension. The obtained composites with different mass ratios were characterized by X-Ray diffraction (XRD), Fourier transformed infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). GQD enhanced electrochemical performance of PPY and, as supercapacitor electrodes, the PPY/GQD composites with the mass ratio of PPY to GQD at 50:1 showed a competitive specific capacitance of 485 F·g^-1 at a scan rate of …

Electrochemical Behavior And Content Determination Of Paeonol At Poly Sudan Ⅲ Modified Electrode, Yan-Jie Zheng, Ai-Lin Liu, Yun Lei, Xin-Hua Lin

Journal of Electrochemistry

The poly SudanⅢ modified electrode was characterized by electrochemical impedance spectroscopy（EIS）and cyclic voltammetry (CV), while the electrochemical behavior of paeonol was studied by cyclic voltammetry (CV). The result shows that the poly Sudan Ⅲ modified electrode exhibits excellent electrocatalytic effect on the oxidation of paeonol. The peak currents of differential pulse voltammetry are linear to the paeonol concentrations over the range of 3.0*10^-7 ~ 2.2*10^-5 mol·L^-1. The detection limit has been estimated to be 5.0*10^-8 mol·L^-1. This method can be used for determination of paeonol content in real sample with satisfactory results.

Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode, Jing Su, Hai-Bo Lin, Hong Xu, Wei-Min Huang, Ya-Peng He

Journal of Electrochemistry

The electrocatalytic oxidation degradation kinetics of oxalic acid in a cylindrical electrochemical reactor with Ti/IrO₂-Ta₂O₅  as an anode was studied. The relation between instantaneous current efficiency and organic concentration in bulk was established based on the two paths for direct electrochemical oxidations, and the theoretical model was verified by experiments. The experimental resultswere reasonably consistent with the established kinetic model. Furthermore, the competition between the two paths was explored with the modelparameter analysis.

Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix, Sirs Ignasi, Antonio Garrido Jos, Brillas Enric

Journal of Electrochemistry

Here, we report the performance of electro-oxidation and electro-Fenton with a boron-doped diamond (BDD) anode for the treatment of single and multicomponent solutions containing small amounts of pharmaceutical residues (i.e., 1 mg·L^-1 paracetamol and/or 1 mg·L^-1 salicylic acid) spiked into a real water matrix at pH 3.0. Electro-oxidation was performed in a BDD/Pt cell, whereas electro-Fenton was carried out in a BDD/air-diffusion cell to electrogenerate H₂O₂ at the cathode, always operating at constant current density. It was found that the decay of both pharmaceuticals by electro-oxidation was more rapid in the real water matrix than …

Probabilistic Simulation Of Solidification Microstructure Evolution During Laser-Based Metal Deposition, Jingwei Zhang, Frank W. Liou, William Seufzer, Joseph William Newkirk, Zhiqiang Fan, Heng Liu, Todd E. Sparks

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A predictive model, based on a Cellular Automaton (CA) - Finite Element (FE) method, has been developed to simulate microstructure evolution during metal solidification for a laser based additive manufacturing process. The macroscopic FE calculation was designed to update the temperature field and simulate a high cooling rate. In the microscopic CA model, heterogeneous nucleation sites, preferential growth orientation and dendritic grain growth kinetics were simulated. The CA model was able to show the entrapment of neighboring cells and the relationship between undercooling and the grain growth rate. The model predicted the dendritic grain size, structure, and morphological evolution during …

Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The porosity and architecture of bone scaffolds, intended for use in bone repair or replacement, are two of the most important parameters in the field of bone tissue engineering. The two parameters not only affect the mechanical properties of the scaffolds but also aid in determining the amount of bone regeneration after implantation. Scaffolds with five different architectures and four porosity levels were fabricated using borate bioactive glass (13-93B3) using the selective laser sintering (SLS) process. The pore size of the scaffolds varied from 400 to 1300 μm. The compressive strength of the scaffolds varied from 1.7 to 15.5 MPa …