Materials Science and Engineering Commons^™

Thermodynamic Limit To Photonic-Plasmonic Light-Trapping In Thin Films On Metals, Eric A. Schiff

Physics - All Scholarship

We calculate the maximum optical absorptance enhancements in thin semiconductor films on metals due to structures that diffuse light and couple it to surface plasmon polaritons. The calculations can be used to estimate plasmonic effects on light-trapping in solar cells. The calculations are based on the statistical distribution of energy in the electromagnetic modes of the structure, which include surface plasmon polariton modes at the metal interface as well as the trapped waveguide modes in the film. The enhancement has the form 4n²+nλ/h (n – film refractive index, λ – optical wavelength, h …

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil

Makara Journal of Technology

Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U)

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip

Makara Journal of Technology

It was reported that the extracts of papaya leaves could inhibit the growth of Rhizopus stolonifer. Antibacterial activity of Carica papaya leaf extracts on pathogenic bacteria was observed in this study. Papaya leaves were extracted by using maceration method and three kinds of solvents: ethanol, ethyl acetate, and hexane. Papaya leaf extracts were tested against Bacillus stearothermophilus, Listeria monocytogenes, Pseudomonas sp., and Escherichia coli by agar diffusion method. The objectives of this study were to determine extract ability against pathogenic bacteria, to observe the influence of pH, NaCl, and heat on extracts ability, and to observe extract ability against B. …

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono

Makara Journal of Technology

Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Processing And Dielectric Properties Of Tio2 Thick Films For High-Energy Density Capacitor Applications, Sheng Chao, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Nanosized titanium dioxide (TiO₂) powders (∼40 nm) were used for preparation of tape-casting slurries. Effect of various solvents and dispersants on the dispersibility of TiO₂ slurries was studied by sedimentation tests and rheology measurements. TiO₂ green tapes were prepared by tape-casting method and densified at 1000°C with a sintered density >95%. Dielectric properties of TiO₂ tapes were studied by measuring of dielectric constant, loss factor and dielectric breakdown strength (BDS) with respect to their microstructural development. BDS values as high as ∼1400 kV/cm were obtained for sintered tapes so that energy densities up to 14 …

Giant Magnetostriction In Annealed Co1-XFeX Thin-Films, Dwight Hunter, Will Osborn, Ke Wang, Nataliya Kazantseva, Jason R. Hattrick-Simpers, Richard Suchoski, Ryota Takahashi, Marcus L. Young, Apurva Mehta, Leonid A. Bendersky, Same E. Lofland, Manfred Wuttig, Ichiro Takeuchi

Faculty Publications

Chemical and structural heterogeneity and the resulting interaction of coexisting phases can lead to extraordinary behaviours in oxides, as observed in piezoelectric materials at morphotropic phase boundaries and relaxor ferroelectrics. However, such phenomena are rare in metallic alloys. Here we show that, by tuning the presence of structural heterogeneity in textured Co_1−xFe_x thin films, effective magnetostriction λeff as large as 260 p.p.m. can be achieved at low-saturation field of ~10 mT. Assuming λ100 is the dominant component, this number translates to an upper limit of magnetostriction ofλ100≈5λeff >1,000 p.p.m. Microstructural analyses …

Effect On The Processing Characteristics Of Zno Varistors Produced Using Vibratory Milling, Maura Kelleher, M.S.J. Hashmi

Conference Papers

Abstract. Each manufacturing stage in the production of zinc oxide varistors from powder preparation to the final encapsulated device is important not only for the formation of the varistor component with optimum microstructure and thus electrical characteristics but also for avoiding the introduction of flaws and reduced yield. In this paper the authors describe and discuss the effect of multi-elemental oxide additives having been milled for different durations using a vibratory mill with cylindrical zirconia media on the powder characteristics of the subsequent processing stages. A commercial ZnO varistor formulation was used. The subsequent processing stages that are given particular …

Fabrication Of Size-Tunable Metallic Nanoparticles Using Plasmid Dna As A Biomolecular Reactor, Jacopo Samson, Irene Piscopo, Alex Yampolski, Patrick Nahirney, Andrea Parpas, Amit Aggarwal, Raihan Saleh, Charles Michael Drain

Publications and Research

Plasmid DNA can be used as a template to yield gold, palladium, silver, and chromium nanoparticles of different sizes based on variations in incubation time at 70 °C with gold phosphine complexes, with the acetates of silver or palladium, or chromium acetylacetonate. The employment of mild synthetic conditions, minimal procedural steps, and aqueous solvents makes this method environmentally greener and ensures general feasibility. The use of plasmids exploits the capabilities of the biotechnology industry as a source of nanoreactor materials.

Deformations Of Crystal Frameworks, Ciprian Borcea, Ileana Streinu

Computer Science: Faculty Publications

We apply our deformation theory of periodic bar-and-joint frameworks to tetrahedral crystal structures. The deformation space is investigated in detail for frameworks modelled on quartz, cristobalite and tridymite.

Introducing Porous Silicon As A Sacrificial Material To Obtain Cavities In Substrate Of Soi Wafers And A Getter Material For Mems Devices, Wajihuddin Mohammad

Doctoral Dissertations

Microelectromechanical system (MEMS) resonators have been a subject of research for more than four decades. The reason is the huge potential they possess for frequency applications. The use of a MEMS resonator as the timing element has an experimental history and huge progress has been made in this direction. Vacuum encapsulated MEMS resonators are required for high precision frequency control. Hence, a device with a high quality factor and durability is needed. In this effort, a new process for producing a cavity in the substrate of Silicon on insulator (SOI) MEMS devices and augmenting it with a getter using porous …

Simulation Of The Fluid Flow-Related Phenomena In The Electrolyte Of An Aluminum Electrolysis Cell, Yufeng Wang, Lifeng Zhang, Xiangjun Zuo

Materials Science and Engineering Faculty Research & Creative Works

A full-scale water model and mathematical simulation were used to study the fluid flow-related phenomena in a water model of an aluminum electrolysis cell. the time-dependent, multiphase fluid flow model was developed to represent the complex transient flow in the electrolysis bath. the accuracy of the mathematical model was validated by the ink dispersion and laser doppler velocimetry measurements in the water model. the shape, motion, release frequency of large-size bubbles, the fluid flow pattern, and the electrolyte-metal interface were predicted by the mathematical simulation. the design and operation of the anode were discussed, including the effect of the anode …

Creating A Uniform Magnetic Field For The Equi-Biaxial Physical Testing Of Magnetorheological Elastomers; Electromagnet Design, Development And Testing., Dave Gorman, Stephen Jerrams, Ray Ekins, Niall Murphy

Conference Papers

No abstract provided.

Distributed Spacing Stochastic Feature Selection And Its Application To Textile Classification, Jeffrey D. Clark

Theses and Dissertations

Many situations require the need to quickly and accurately locate dismounted individuals in a variety of environments. In conjunction with other dismount detection techniques, being able to detect and classify clothing (textiles) provides a more comprehensive and complete dismount characterization capability. Because textile classification depends on distinguishing between different material types, hyperspectral data, which consists of several hundred spectral channels sampled from a continuous electromagnetic spectrum, is used as a data source. However, a hyperspectral image generates vast amounts of information and can be computationally intractable to analyze. A primary means to reduce the computational complexity is to use feature …

A Modified Surface On Titanium Deposited By A Blasting Process, Caroline O' Sullivan, Peter O'Hare, Greg Byrne, Liam O'Neill, Katie B. Ryan, Abina M. Crean

Publications

Abstract

: Hydroxyapatite (HA) coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlast™, a novel blasting process has been used to successfully modify a titanium (V) substrate with a HA treatment using a dopant/abrasive regime. …

Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman

Master's Theses

Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.

Synthesis of A-site deficient [A=0.97] Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ (BSCF) was …

A Quantitative Study Of The Weldability Of Inconel 718 Using Gleeble And Varestraint Test Methods, Sean Quigley

Master's Theses

Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating …

Testing, Modelling And Validation Of Numerical Model Capable Of Predicting Stress Fields Throughout Polyurethane Foam, Conor Briody, Barry Duignan, Stephen Jerrams

Conference Papers

Wheelchair seating systems are specialised for a number of reasons as users can have impaired mobility, which increases the possibility of pressure build up. These areas of high pressure frequently occur in the trunk region under the bony prominences known as the Ischial Tuberosities (IT), pressure ulcers may occur consequently. Polyurethane foam has been in use for some time in wheelchair seating systems as it exhibits good pressure relieving capabilities in most cases. However, little quantitative research has gone into foamed polymers, in comparison with conventional elastomeric materials. This lack of knowledge can ultimately lead to more time being spent …

Improved Manufacturing Methods Of Bovine Femur Samples For Ultrasonic Testing And Assessment Of Materials Through Contract Angle Measurement, Kevin Mathew Lopez Galang

Biomedical Engineering

At California Polytechnic State University of San Luis Obispo (Cal Poly), the Biomedical Engineering department (BMED) requires its students to take the course listed as “BMED 420: Principles of Biomaterial Designs.” BMED 420 has a required laboratory section every week throughout the duration of the course that is meant to be a supplemental tool for learning. During the lab sections, students perform experiments and exercises that are currently being implemented in the industry. Despite accuracy of the methods and experiments relative to their use in the industry, there is always room for improvement. The objective of this project will illustrate …