Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2010

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 31 - 60 of 328

Full-Text Articles in Materials Science and Engineering

Transient Fluid Flow Phenomena During Continuous Casting: Part Ii-Cast Speed Change, Temperature Fluctuation, And Steel Grade Mixing, Yufeng Wang, Lifeng Zhang Dec 2010

Transient Fluid Flow Phenomena During Continuous Casting: Part Ii-Cast Speed Change, Temperature Fluctuation, And Steel Grade Mixing, Yufeng Wang, Lifeng Zhang

Materials Science and Engineering Faculty Research & Creative Works

Many complicated phenomena are associated with transient stages during the continuous casting process, especially inside the casting mold cavity. a deep understanding of the phenomena and optimized control over the process ensure the high-quality product and low costs. This work presents a three-dimensional numerical simulation of transient fluid flow phenomena during steel continuous casting. in the Part II, the process of casting speed change (increase or decrease), temperature fluctuation, and steel grade mixing in a slab mold were investigated. the phenomena, such as flow pattern, inclusion removal fraction, temperature variation, top surface profile, and steel transportation, were addressed to evaluate …

Go to article

A Simple Model To Calculate Dendrite Growth Rate During Steel Continuous Casting Process, Mujun Long, Lifeng Zhang, Fei Lu Dec 2010

A Simple Model To Calculate Dendrite Growth Rate During Steel Continuous Casting Process, Mujun Long, Lifeng Zhang, Fei Lu

Materials Science and Engineering Faculty Research & Creative Works

In the current paper, the relationship between the casting speed and the dendrite growth during steel continuous casting process was studied; and a simple mathematical model to calculate the primary dendrite growth rate according to the casting speed was developed. the model was used to predict the distribution of the dendrite growth rate along width direction and casting direction during a continuous casting process, indicating a dendrite growth rate of 0.1-3.0 mm/s, which is much higher than that in regular ingot casting. the dendrite growth rate fluctuates along casting direction because of the different cooling intensity in each zone of …

Go to article

Thermal Properties Of Lunar Regolith Simulants, Kenneth W. Street, Chandra Ray, Doug Rickman, Daniel A. Scheiman Nov 2010

Thermal Properties Of Lunar Regolith Simulants, Kenneth W. Street, Chandra Ray, Doug Rickman, Daniel A. Scheiman

Materials Science and Engineering Faculty Research & Creative Works

Various high temperature chemical processes have been developed to extract oxygen and metals from lunar regolith. These processes are tested using terrestrial analogues of the regolith. But all practical terrestrial analogs contain H2O and/or OH-, the presence of which has substantial impact on important system behaviors. We have undertaken studies of lunar regolith simulants to determine the limits of the simulants to validate key components for human survivability during sustained presence on the moon. Differential Thermal Analysis (DTA) yields information on phase transitions and melting temperatures. Thermo-Gravimetric Analysis (TGA) with Fourier Transform Infrared (FTIR) analysis provides information on …

Go to article

Plasma Processing Of Lunar Regolith Simulant For Oxygen And Glass Production, S. Sen, D. Butts, J. S. O'Dell, C. S. Ray Nov 2010

Plasma Processing Of Lunar Regolith Simulant For Oxygen And Glass Production, S. Sen, D. Butts, J. S. O'Dell, C. S. Ray

Materials Science and Engineering Faculty Research & Creative Works

Tools for extracting life-sustaining resources from the moon are needed to support the vision for space exploration. of particular interest is the production of oxygen for life support and propulsion. on the lunar surface the only practical source for oxygen is the lunar regolith. Described in this paper is an innovative plasma reduction technique for the production of oxygen from lunar regolith. Thermodynamic calculations showed that the regolith oxides could be dissociated to yield up to 7.3 weight percent oxygen when exposed to extremely high temperatures of up to 3000°C. Subsequently the use of a plasma flame to obtain oxygen …

Go to article

Electrochemical Detection For The Corrosion Of Reinforcing Steel In Concrete During Immersion And Drying Cycles, Bing-Li Jia, Fa-He Cao, An-Na Chen, Jian-Qing Zhang Nov 2010

Electrochemical Detection For The Corrosion Of Reinforcing Steel In Concrete During Immersion And Drying Cycles, Bing-Li Jia, Fa-He Cao, An-Na Chen, Jian-Qing Zhang

Journal of Electrochemistry

The corrosion behavior of reinforcing steel in concrete under dry-wet cycle condition has been studied by electrochemical noise(EN) compared with the electrochemical impedance spectroscopy(EIS),SEM micrographs and EDS.The statistical method has been employed to analyze the EN data of reinforcing steel in concrete,which revealed three different corrosion stages of reinforcing steel in concrete,including the dissolution of the passive film,the active corrosion and the cumulation of corrosion product.The wavelet transform has also been employed,which indicated that steel in concrete with pH 1 is associated with uniform corrosion,while steel in concrete with pH 3 and pH 7 are associated with localized corrosion,such as …

Go to article

Study On Preparing Technology And Corrosion Resistance Of Ti/Zr Based Chromium-Free Chemical Conversion Coating On Zinc Electroplating Layer, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan Nov 2010

Study On Preparing Technology And Corrosion Resistance Of Ti/Zr Based Chromium-Free Chemical Conversion Coating On Zinc Electroplating Layer, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan

Journal of Electrochemistry

In this paper,we obtained environmental-friendly chromium-free chemical conversion coating on the non-cyanide alkaline zinc electroplating layer by employing the optimized Ti/Zr based conversion technique.At the same time,the performances of the Ti/Zr based conversion coating were compared with chromate colour passivation coating.The corrosion resistances of the conversion coatings were investigated by using neutral salt spray(NSS) test,potentiodynamic polarization and electrochemical impedance spectroscopy(EIS).The results showed that the white rust appeared after 96 hours when the NSS test was performed on the Ti/Zr based conversion coating,which was close to the corrosion resistance rating of chromate colour passivation coating.Compared with the chromate passivation coating,the Ti/Zr …

Go to article

Preparation And Characterization Of The Silane-Phosphonic Acid Composite Passivation Coating For Electrogalvanized Steel, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan Nov 2010

Preparation And Characterization Of The Silane-Phosphonic Acid Composite Passivation Coating For Electrogalvanized Steel, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan

Journal of Electrochemistry

A new silane-phosphonic acid composite passivation coating process has been developed for the protection of electrogalvanized steel based on N-(β-aminoethyl)-γ-aminopropyltrimethoxysilane(AAPTMS),γ-(2,3-epoxypropoxy)propyltrimethoxy-silane(GPTMS) and 1-hydroxy ethylidene-1,1-diphosphonic acid(HEDP).The results of X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FTIR),potentiodynamic polarization scan,electrochemical impedance spectroscopy(EIS) and neutral salt spray(NSS) tests indicated that the major structure of the prepared silane-phosphonic acid composite passivation coating consisted mainly of Si—O—Si and Si—O—P bonds.The area of white rust was not more than 5% of the total panal after 120 h NSS test,which could be compared favourably with the chromate colour passivation coating.However,the corrosion reaction on the anode of the silane-phosphonic acid composite passivation …

Go to article

The Roles Of The Width Of Gas/Liquid/Solid Three-Phase Boundary Zone Of Dispersion Water Films In Atmospheric Corrosion Of Metals, Jia Wang, Jing Jiang Nov 2010

The Roles Of The Width Of Gas/Liquid/Solid Three-Phase Boundary Zone Of Dispersion Water Films In Atmospheric Corrosion Of Metals, Jia Wang, Jing Jiang

Journal of Electrochemistry

The roles of TPB(Three-Phase Boundary) width in the corrosion processes of metals under dispersed water films were investigated by electrochemical techniques combined with contact angle measurement.It is found that both cathodic limiting current density and corrosion current density linearly increases with increasing the TPB width,confirming the important role of TPB width in gas/liquid/solid multiphase corrosion systems.Based on above results,the effect of water film thickness on atmospheric corrosion rate was quantitatively evaluated by the TPB width.

Go to article

Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du Nov 2010

Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du

Journal of Electrochemistry

The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO2 thin films were prepared by adding Ti(O-n-Bu)4 as the precursor into concentrated HNO3,H2SO4 and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO2 thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO2 nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO2 thin films.

Go to article

Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen Nov 2010

Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen

Journal of Electrochemistry

The cathode materials of LiFePO4 were prepared via a hydrothermal reduction method using FeCl3 as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO4 was obtained based on the test results of XRD and FTIR.Carbon-coated LiFePO4 was synthesized by pyrolysisng glucose at high temperature.The morphologies of pure LiFePO4 displayed cluster-like while the LiFePO4/C displayed sphere-like particles.The electrochemical test showed that the LiFePO4/C had good rate performance,while LiFePO4 delivered much lower discharge capacity.

Go to article

Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan Nov 2010

Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

The polarization measurements and electrochemical impedance spectroscopy(EIS) were used to study the corrosion electrochemical behavior of AM60 magnesium alloys in three kinds of commercial coolants for automobile engine.Results show that the tested commercial coolants are slightly corrosive to AM60 magnesium alloys and their corrosivity varies from coolant to coolant.The coolant C is the least corrosive among the studied commercial coolants and the coolant A is more corrosive than the coolant B and C.The coolant C appears to be the most promising coolant for automobile engine made by magnesium alloys.The coolant resistivity plays an important role in the corrosion of AM60 …

Go to article

Electrodeposition Of Lead Dioxide From Dluoroborate Solutions, Chun-Mei Kong, Yong-Ming Tang, Wen-Zhong Yang, Xiao-Yuan Yang Nov 2010

Electrodeposition Of Lead Dioxide From Dluoroborate Solutions, Chun-Mei Kong, Yong-Ming Tang, Wen-Zhong Yang, Xiao-Yuan Yang

Journal of Electrochemistry

The PbO2 anodes were prepared on platinum from fluoroborate media and its doped solutions by electrodeposition technique.Elecchemical and pysicochemical properties of these PbO2 films were studied by cyclic voltammetry methods,XRD and SEM.The results showed that the presence of BF4-increased PbO2 electrodeposition rate;the prepared lead dioxide consisted of β-PbO2;the preferential orientation of crystals and surface morphology were affected a lot by doping F-and Fe3+.The FB/F-Fe-PbO2 electrode exhibited regular-shaped layers with compact morphology.Furthermore,increasing current density also change the preferential orientation of PbO2 crystals.

Go to article

The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai Nov 2010

The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai

Journal of Electrochemistry

Li3V2(PO4)3/C was synthesized by sol-gel method with citric acid as chelate and C sources. Physical and electrochemical performances of as-prepared materials were characterized through XRD, SEM and galvanostatic charge-discharge tests,etc. The results showed that products produced by calcining at 800 ℃ for 12 h had a single phase crystal structure and relatively small particle sizes with uniform distribution. At 0.1 C, 0.5 C and 1 C, the initial specific discharge capacities were 153.0, 143.1 and 130.6 mAh·g-1, respectively, and capacity efficiencies were 93.1%, 85.4% and 77.3% after 50 cycles, respectively. …

Go to article

Research On Nafion/Sio2 Composite Membrane In All Vanadium Redox Flow Battery, Dong-Dong Liu, Mao-Cai Lin, Tao Guan, Qing-Chun Yu Nov 2010

Research On Nafion/Sio2 Composite Membrane In All Vanadium Redox Flow Battery, Dong-Dong Liu, Mao-Cai Lin, Tao Guan, Qing-Chun Yu

Journal of Electrochemistry

The Nafion117/SiO2 composite membrane was prepared by sol-gel method.The results showed that,during composite membrane preparation process,the ratio of MeOH and TEOS did not affect the penetration rate of VO2+ basically,however,the lowest permeability of 427×10-9cm2/s in the membrane was achieved while hydrolysis time was 10 min and natural drying for 24 h after hydrolysis,which reduced by 52 times than that in Nafion117 membrane.The SEM tests proved that SiO2 grains grew bigger in the composite membrane during the natural drying,and most of the holes in Nafion117 were filled.Single cell test showed the battery power efficiency was improved …

Go to article

Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang Nov 2010

Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang

Journal of Electrochemistry

The electrochemical reduction processes of oxygen in different non-aqueous solvents such as acetonitrile(MeCN),propylene carbonate(PC) and their mixtures were investigated by cyclic voltammetry method.The results indicated a one electron reduction of oxygen to O2-occured in these systems as a first step reduction,no matter whether in tetrabutylammonium hexafluorophosphate(TBAPF6)/MeCN or TBAPF6/PC electrolyte.However,the CV curves in 0.1 mol·L-1 TBAPF6/MeCN showed a couple of reversible redox peaks,indicating that the reduction process of oxygen was irreversible in the 0.1 mol·L-1 TBAPF6/PC electrolyte.In the PC-based electrolyte,the reduction current peak reduced largely and the oxidation peak …

Go to article

Initial Stage Of Atmospheric Corrosion Of Ndfeb(M35) In A Simulated Marine Atmosphere, Chun-Ling Li, Yuan-Tai Ma, Ying Li, Fu-Hui Wang Nov 2010

Initial Stage Of Atmospheric Corrosion Of Ndfeb(M35) In A Simulated Marine Atmosphere, Chun-Ling Li, Yuan-Tai Ma, Ying Li, Fu-Hui Wang

Journal of Electrochemistry

This study detailed the atmospheric corrosion behaviour of sintered NdFeB(M35) in a simulated marine atmosphere with 80% relative humidity(RH).The dissolution and subsequent reaction of NaCl particles cause the attack of NdFeB.The corrosion presented three representative types:if the electrolyte covered magnetic phase and Nd-rich phase,the Nd-rich phase was corroded firstly due to galvanic effect;if the electrolyte covered magnetic phase,magnetic phase was corroded along the grain boundary;if the electrolyte located near the position of defects,corrosion progressed along with the defect because of low concentration of oxygen inside the defect.With corrosion progressing,local corrosion areas were mutually connected,with Nd-rich phase and grain boundary being …

Go to article

Effect Of Cldh On Rebar Corrosion Behavior In Chloride Contaminated Neutral Pore Solutions, Yu-Ming Tang, Le Niu, Yu Zuo Nov 2010

Effect Of Cldh On Rebar Corrosion Behavior In Chloride Contaminated Neutral Pore Solutions, Yu-Ming Tang, Le Niu, Yu Zuo

Journal of Electrochemistry

he effect of calcined LDH-MgAl-CO3 on rebar corrosion behavior in chloride ion contaminated neutral concrete pore solutions was investigated in this paper.Corrosion potentials of rebars in pore solutions after treatment with CLDH were higher than before treatment.According to polarization tests,passivated region of rebars in pore solutions after treatment with CLDH was found apparently instead of activation.EIS tests showed that CLDH made the impedance of specimens increase.The measurements of pH and chloride ion concentration after treatment indicated that / of pore solutions decreased by 4～5 magnitude orders.

Go to article

Effect Of Process Parameters On Abnormal Grain Growth During Friction Stir Processing Of A Cast Al Alloy, S. Jana, Rajiv S. Mishra, J. A. Baumann, G. Grant Nov 2010

Effect Of Process Parameters On Abnormal Grain Growth During Friction Stir Processing Of A Cast Al Alloy, S. Jana, Rajiv S. Mishra, J. A. Baumann, G. Grant

Materials Science and Engineering Faculty Research & Creative Works

The effects of process parameters and friction stir processing (FSP) run configurations on the stability of nugget microstructure at elevated temperatures were evaluated. Cast plates of an Al-7Si-0.6Mg alloy were friction stir processed using a combination of tool rotation rates and tool traverse speeds. All single pass runs showed some extent of abnormal grain growth (AGG), whereas multi-pass runs were more resistant to AGG. Additionally, higher tool rotation rate was found to be beneficial for controlling AGG. These effects were analyzed by comparing the result of this work with other published results and AGG models. © 2010 Elsevier B.V.

Go to article

Virtual Coatings Application System, Jason M. Ebsensberger, Michael J. Bolick, Richard J. Klein Ii, Eric C. Peterson, Chad J. Zalkin, James B. Fisher, Leslie C. Hughes Nov 2010

Virtual Coatings Application System, Jason M. Ebsensberger, Michael J. Bolick, Richard J. Klein Ii, Eric C. Peterson, Chad J. Zalkin, James B. Fisher, Leslie C. Hughes

Patents (University of Northern Iowa)

A virtual coatings application system has several features to enhance the realism of simulated spray painting. The system generally includes a display screen on which is defined a virtual surface (such as a truck door) that is intended to be virtually painted or coated by the user. Alternatively, the system includes a head-mounted display unit that displays a virtual spray painting environment in which the virtual surface is defined. The user operates an instrumented spray gun controller that outputs one or more signals representing data as to the status of the controls on the spray gun controller. The system also …

Go to article

Virtual Coatings Application System, Jason M. Ebensberger, Michael J. Bolick, Jeremiah G. Treloar, Richard J. Klein Ii, Eric C. Peterson, Chad J. Zalkin, James B. Fisher, Leslie C. Hughes Nov 2010

Virtual Coatings Application System, Jason M. Ebensberger, Michael J. Bolick, Jeremiah G. Treloar, Richard J. Klein Ii, Eric C. Peterson, Chad J. Zalkin, James B. Fisher, Leslie C. Hughes

Patents (University of Northern Iowa)

A virtual coatings application system has several features to enhance the realism of simulated spray painting. The system generally includes a display screen on which is defined a virtual surface (such as a truck door) that is intended to be virtually painted or coated by the user. The user operates an instrumented spray gun controller that outputs one or more signals representing data as to the status of the controls on the spray gun controller. The system also has a motion tracking system that tracks the position and orientation of the spray gun controller with respect to the virtual surface …

Go to article

Microstructural Evolution During Fatigue Of Ultrafine Grained Aluminum Alloy, P. S. De, Rajiv S. Mishra Nov 2010

Microstructural Evolution During Fatigue Of Ultrafine Grained Aluminum Alloy, P. S. De, Rajiv S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

A comparative study of the surface microstructural changes during fatigue of a precipitation hardened (PH) aluminum alloy in ultrafine grained (UFG) and microcrystalline conditions was done using orientation imaging microscopy (OIM). with increase in applied stress amplitude, the fatigue life of fine-grained PH alloy deteriorated. on the other hand, at lower stress amplitudes an improvement in fatigue life was noted. This trend was reversed for the coarse-grained PH alloy. in UFG alloy, the fatigue life improved at all stress amplitudes. the variation in fatigue life response between coarse, fine and ultrafine grain PH alloy was due to the increased interaction …

Go to article

The Relationship Between Induced Fluid Structure And Boundary Slip In Nanoscale Polymer Films, Nikolai V. Priezjev Nov 2010

The Relationship Between Induced Fluid Structure And Boundary Slip In Nanoscale Polymer Films, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The molecular mechanism of slip at the interface between polymer melts and weakly attractive smooth surfaces is investigated using molecular dynamics simulations. In agreement with our previous studies on slip flow of shear-thinning fluids, it is shown that the slip length passes through a local minimum at low shear rates and then increases rapidly at higher shear rates. We found that at sufficiently high shear rates, the slip flow over atomically flat crystalline surfaces is anisotropic. It is demonstrated numerically that the friction coefficient at the liquid-solid interface (the ratio of viscosity and slip length) undergoes a transition from a …

Go to article

Synthesis Of Mild–Hard Aao Templates For Studying Magnetic Interactions Between Metal Nanowires, Jin-Hee Lim, Aurelian Rotaru, Seong-Gi Min, Leszek Malkinski, John B. Wiley Nov 2010

Synthesis Of Mild–Hard Aao Templates For Studying Magnetic Interactions Between Metal Nanowires, Jin-Hee Lim, Aurelian Rotaru, Seong-Gi Min, Leszek Malkinski, John B. Wiley

Physics Faculty Publications

The sequential application of mild and hard anodization techniques in the fabrication of porous aluminamembranes allows one to decrease the number of continuous pores in anodized aluminium oxide (AAO) templates. Initially, standard mild anodization techniques were used to create porous templates with 100 nm interpore distances and 70 nm pore diameters. Hard anodization treatment on the same membrane then produced interpore distances of about 265 nm with diameters of 110 nm. At the interface between the two anodization steps, many of the mild-side pores were terminated to create a mild–hard membrane (Mi–Ha AAO) where the functional interpore distances were 200–300 …

Go to article

Simulation On The Use Of Losat Data For Rice Field Mapping, Bambang H. Trisasongko, Dyah R. Panuju, Boedi Tjahjono, Baba Barus, Hari Wijayanto, Mahmud A. Raimadoya, Irzaman Irzaman Nov 2010

Simulation On The Use Of Losat Data For Rice Field Mapping, Bambang H. Trisasongko, Dyah R. Panuju, Boedi Tjahjono, Baba Barus, Hari Wijayanto, Mahmud A. Raimadoya, Irzaman Irzaman

Makara Journal of Technology

Simulation on the Use of LOSAT Data for Rice Field Mapping. Since the launch of LAPAN-TUBSAT satellite in 2007, Indonesia has been developing mission on earth observation missions for various applications. The next generation mission, called LAPAN-ORARI Satellite (LOSAT), is currently under development and expected to be launched in 2011. In order to facilitate the applications, a thorough assessment of the sensor should be made. This paper presents an examination of simulated LOSAT data for rice monitoring and mapping purposes coupled with QUEST statistical tree. We found that three-band simulated LOSAT data were suitable for the task with reasonably high …

Go to article

An Empirical Model For Build-Up Of Sodium And Calcium Ions In Small Scale Reverse Osmosis, Subriyer Nasir Nov 2010

An Empirical Model For Build-Up Of Sodium And Calcium Ions In Small Scale Reverse Osmosis, Subriyer Nasir

Makara Journal of Technology

A simple models for predicting build-up of solute on membrane surface were formulated in this paper. The experiments were conducted with secondary effluent, groundwater and simulated feed water in small-scale of RO with capacity of 2000 L/d. Feed water used in the experiments contained varying concentrations of sodium, calcium, combined sodium and calcium. In order to study the effect of sodium and calcium ions on membrane performance, experiments with ground water and secondary effluent wastewater were also performed. Build-up of salts on the membrane surface was calculated by measuring concentrations of sodium and calcium ions in feed water permeate and …

Go to article

The Effect Of Enzymatic Hydrolysis On The Properties Of Protein Hydrolysate From Paddy Mushroom, Niken Widya Palupi, Wiwik Siti Windrati, Tamtarini Tamtarini Nov 2010

The Effect Of Enzymatic Hydrolysis On The Properties Of Protein Hydrolysate From Paddy Mushroom, Niken Widya Palupi, Wiwik Siti Windrati, Tamtarini Tamtarini

Makara Journal of Technology

Protein hydrolysate was prepared from Paddy (Volvariella volvaceae) mushroom. Hydrolysis uses commercially protease available Protamex ™ with enzyme concentration of 0.1% (w/w). Hydrolysis was performed at three different temperatures (room temperature, 40 °C, and 50 °C) with different incubation periods (60, 90, and 120 minutes). Enzyme inactivation was done in 90 °C for 3 minutes. Yield and degree of hydrolysis ranged from 94.76% to 99.55% and 19.06% to 24.59%. Protein solubility was about 89–11,8%. The longer time of hydrolysis, the darker the color of protein hydrolysate. Protein hydrolysate which has hydrolysis at 50 °C for 120 minutes has the highest …

Go to article

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati Nov 2010

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati

Makara Journal of Technology

Diafiltration by means of the ultrafiltration system of probiotic fermented Mung beans (Phaseolus radiatus L.) concentrate has been performed to reduce or eliminate salts and smaller impurities than the nominal cut-off of the membrane of 20,000 nominal weight cut-off (NWCO). These processes have been conducted as an attempt in order to get a probiotic product with organoleptic acceptability, composition, and the optimal total lactic acid bacteria (LAB) counts because the presence of salts will affect on the viability of LAB and the cell lysis of LAB and limit its utility in food products. Concentrate of probiotic mung beans was prepared …

Go to article

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin Nov 2010

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin

Makara Journal of Technology

High Pressure Adsorption Isotherm of CO2 on Activated Carbon using Volumetric Method. Adsorption system is ones of the most effective methods for CO2 separating with other substances that produced from the burning of fossil fuels. In the design for that application, beside of characteristics of porous material (adsorbent) data, CO2 adsorption data on the adsorbent (kinetic and thermodynamic) are also needed. The aim of this research is resulting isothermal adsorption data at pressures up to 3.5 MPa by indirect methods (volumetric method) at isothermal temperature of 300, 308, 318 and 338 K. Adsorbent that used in this research is activated …

Go to article

Concept Design And Testing Of Multi-Nozzle Water Mist Fire Suppression System, Danardono A. Sumarsono, Yulianto S. Nugroho, Mariance Mariance, I Gede Wahyu W. Ariasa Nov 2010

Concept Design And Testing Of Multi-Nozzle Water Mist Fire Suppression System, Danardono A. Sumarsono, Yulianto S. Nugroho, Mariance Mariance, I Gede Wahyu W. Ariasa

Makara Journal of Technology

In this work a flexible design of multi-nozzle arrangement of water mist fire suppression system was studied. The source of fire was a 65 mm diameter cooking oil fire. An investigation on the impact of nozzle arrangement on the temperature profile of fires was conducted. The occurance of oil splash due to the application of water mist was also studied. The water mist systems developed in the present work can effectively extinguish cooking oil fires and prevented them from re-ignition. The spray angle, discharge pressure, and water flow rate were important factors to determine the effectiveness of water mist in …

Go to article

The Stability Characteristics Of Sandbag Submerged Breakwater, Ferry Fatnanta, Widi Agoes Pratikto, Haryo Dwito Armono, Wahyudi Citrosiswoyo Nov 2010

The Stability Characteristics Of Sandbag Submerged Breakwater, Ferry Fatnanta, Widi Agoes Pratikto, Haryo Dwito Armono, Wahyudi Citrosiswoyo

Makara Journal of Technology

The Stability Characteristics of Sandbag Submerged Breakwater. Breakwater is one of coastal structures to overcome problems of abrasion. Due to difficulties in obtaining rock material at the coastal area. The using of sandbags as a breakwater provides advantages in utilizing local materials. A Sandbag has a smooth surface, so the internal shear forces are relatively small. According to these phenomena, the research for parameters that are expected to affect the stability of the sand bags. These parameters are a slope, shape and formation of sand bags. This experimental research conducted in two dimensional physical model and took place on the …

Go to article

First Prev Next Last