Materials Science and Engineering Commons^™

Detection Of Residual Stress In Sic Mems Using Μ-Raman Spectroscopy, John C. Zingarelli

Theses and Dissertations

Micro-Raman (µ-Raman) spectroscopy is used to measure residual stress in two silicon carbide (SiC) poly-types: single-crystal, hexagonally symmetric 6H-SiC, and polycrystalline, cubic 3C-SiC thin films deposited on Si substrates. Both are used in micro-electrical-mechanical systems (MEMS) devices. By employing an incorporated piezoelectric stage with submicron positioning capabilities along with the Raman spectral acquisition, spatial scans are performed to reveal areas in the 6H-SiC MEMS structures that contain residual stress. Shifts in the transverse optical (TO) Stokes peaks of up to 2 cm^-1 are correlated to the material strain induced by the MEMS fabrication process through the development of phonon …

Dynamic Characterization Of Thin Deformable Pvdf Mirror, Eric M. Trad

Theses and Dissertations

Methodology for the design and fabrication of 5 inch diameter membrane-like mirror structures is explored, resulting in test articles with areal densities as low as 1.57 kg/m2 and a thickness of 1.5 mm. Each optical structure has 7 control patches etched into the PVDF layer, which can be used as actuators. These test articles are utilized to demonstrate the capabilities of an acquisition system to make measurements of static and dynamic actuation of the mirror surface. Static deformations are analyzed statistically and determined to yield maximum deformations in the actuated regions of -2.1 micro with a standard deviation of 0.33 …

Tensile Stress Rupture Behavior Of A Woven Ceramic Matrix Composite In Humid Environments At Intermediate Temperature, Kevin J. Larochelle

Theses and Dissertations

Stress rupture tests on the Sylramic^TM fiber with an in-situ layer of boron nitride, boron nitride interphase, and SiC matrix ceramic matrix composite were performed at 550°C and 750°C with 0.0, 0.2, or 0.6 atm partial pressure of water vapor, pH₂O. The 550°C, 100-hr strengths were 75%, 65% and 51% of the monotonic room temperature tensile strength, respectively. At 750°C, the strengths were 67%, 51%, and 49%, respectively. Field Emission Scanning Electron Microscopy analysis estimated the total embrittlement times for 550°C with 0.0, 0.2, and 0.6 atm pH₂O were >63 hrs, >38 hrs, and between …

Corrosion Behavior Of Mg2-XLaXNi And Mg2-XCeXNi Hydrogen Storage Alloy, Hai-Chang Zhang, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

The corrosion behavior of Mg-base hydrogen storage alloys has been investigated by potentiodynamic polarization and EIS. The results showed that the corrosion current density (i_corr) and the electrochemical polarized resistance of Mg_2-xCe_xNi alloys decreased with x increase, while i_corr of Mg_2-xLa_xNi alloys increased and the electrochemical polarized resistance of Mg_2-xLa_xNi alloys increased first, then decreased with x increase. SEM results showed that the surface of Mg_1.85Ce_0.15Ni alloy was relatively even while the surface of Mg_2-xLa_xNi alloy had …

Corrosion Resistance For Tio2 Thin Films Coated 316l Stainless Steel In The Nacl Solution, Guang-Xia Shen, Yi-Cong Chen, Chang-Jian Lin

Journal of Electrochemistry

The nano-TiO₂ thin films have been deposited on the 316L stainless steel by sol-gel and the dip-coating methods. Hydrothermal post-treatment leads to crack-free coatings. Meanwhile, the surface structure and properties are optimized. Surface morphology, structure and properties are characterized by XRD, and SEM technologies. The results have shown that the surface of coatings is porous, uniform and orderly, the particle diameters are in the range of 15~18 nm and the pores are about 4~8 nm and TiO₂ is anatase. The results of electrochemical measurements show that in the NaCl solution with pH ≥ 2 and concentration below 1mol/L, …

Calcium Zincate Prepared By Ball Mill Method, Sheng-Xian Li, Shuan-Bao Tian, Shao-Shan Zhu

Journal of Electrochemistry

Calcium zincate was prepared by ball milling method and the factors that influence its synthesis were investigated. The composition of the compound was Ca(OH)₂·2Zn(OH)_2^·2H₂O, which was verified by XRD and TG-DTA methods. The results of powder microelectrode and in simulated batteries showed that the material had excellent cyclic performance.

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Influence of La(OH)₃ or Ce(OH)₃ in secondary zinc electrode was investigated by the cyclic voltammetry, potentiodynamic polarizationand potentiostatic polarization tests and influence of La₂O₃ or CeO₂ in the charge/discharge performance of Zn/Ni battery was studied by galvanostatic charge/discharge experiment. The results showed that the film of rare earth hydroxide prevented the zincate species from transferring toward solution, enhanced hydrogen overpotential and decreased thecorrosion current density (i_corr), and therefore inhibited zinc corrosion. The potentiostatic polarization results at100mV overpotential showed that La(OH)₃ or Ce(OH)₃ oated on the zinc electrode effectively suppressed the …

Electrochemical Performance Of Gel Polymer Electrolyte Prepared By Thermal Initiating Polymerization Of Acrylates, Jin-Dan Piao, Li-Xia Yuan, Xin-Ping Ai, Han-Xi Yang, Yu-Liang Cao

Journal of Electrochemistry

A gel polymer electrolyte was prepared by thermal initiating polymerization of the acrylates in the EC/EMC/DMC electrolyte solution at 100℃. The LiCoO₂/MCMB polymer cells were assembled and their electrochemical properties were evaluated at various charge-discharge rate and temperatures. The ionic conductivity of the polymer electrolyte containing 85wt.% liquid electrolyte is around 3.2×10^-3 S·cm^-1  at 20℃ and 5.6×10^-4 S·cm^-1 at -30℃ respectively. The gel polymer electrolyte has good electrochemical stability up to 4.5V versus Li/Li⁺.The first charge-discharge efficiency of the polymer cell at 0.2C rate is almost 92.1%. The discharge capacity of the …

The Fabrication And Electrochemical Studies On Carbon Nanotube Array Electrodes, Quan-Yong Gao, Jing Zhang, Yong Yang

Journal of Electrochemistry

An improved technique for fabrication of carbon nanotube array electrodes has been proposed in this work. Firstly, carbon nanotubes (CNs) array electrodes were prepared by combsination of Chemical Vapor Decomposition (CVD) method and sputtering techniques in anodized aluminum oxide (AAO) membrane. The CNs/AAO was immersed into HF solution to remove the barrier layer. Controlling the immersing time, the CNs array electrodes with different length contacted with electrolyte can be prepared. The morphology of CNs array electrodes was observed by SEM. The electrochemical properties of CNs array electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammetric curves of …

Fabrication And Studies Of A Novel Ag/Agcl Reference Electrode In High Temperature Molten Chloride Salts, Pei Gao, Xian-Bo Jin, Di-Hua Wang, Xiao-Hong Hu, Zheng Chen

Journal of Electrochemistry

A new method for the easy fabrication of a stable and long life silver/silver chloride reference electrode in molten chloride salts is described in this paper. The method is based on the fact that simply placing the silica glass in molten NaCl or its vapour in the presence of oxygen resulted in satisfactory conductivity for sodium ion and possibly calcium ion in the material.The performance of such made electrode has been investigated in a few typical chloride systems at temperatures ranging from 400 to 900℃. Due to the wholly sealed construction, the reference electrode is stable, temperature-reversible, contamination free to …

A Study Of Metal Borides As High Capacity Anode Materials For Aqueous Primary Batteries, Ya-Dong Wang, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

The transition metal borides VB₂ and TiB₂ were tested as high capacity anode materials and their electrochemical behaviors were studied by cyclic voltammetry and discharge measurements. The experimental results indicated that transition metal borides VB₂ and TiB₂ electrodes can deliver exceptionally high discharge capacity of over 3100 mAh/g and 1 600 mAh/g respectively, corresponding to 11- and 6-electron oxidation reaction, although their parent elements V, Ti and boron, are almost completely electrochemically inert. The different electrochemical activitis were probably due to the electrochemical activation of boron, which clamp the potential to passivation for Ti and activity …

Anodic Polarization Behaviors Of Carbon Steel In Bicarbonate Solution, Jing-Mao Zhao, Yu Zuo

Journal of Electrochemistry

The anodic polarization curves of mild steel were measured in sodium bicarbonate solution of various concentrations, and the surface products were analyzed by XPS. Two anodic current peaks and two passive zones are observed in all the curves. When HCO₃^- ions concentration is below 0.1mol/L, the two peaks are so close that the first passive zone is difficult to be observed. When HCO₃^- ions concentration is above 0.1 mol/L, the first peak appears clear, while the second becomes smaller. The XPS results indicate that the out layer of film formed at a higher potential is mainly …

Preparation And Characterization Of Lini0.85Co0.10(Timg)0.025O2 As Cathode Materials For Lithium-Ion Batteries, Xian-Jun Zhu, Hong-Hao Chen, Hui Zhan, Dai-Ling Yang, Yun-Hong Zhou

Journal of Electrochemistry

Cathode material of LiNi_0.85Co_0.10(TiMg)_0.025O₂ were prepared by solid state reaction at 725℃ for 24 h from LiOH·H₂O, Ni₂O₃, Co₂O₃, TiO₂ and Mg(OH)₂ under flowing oxygen, and were characterized by TG-DTA, XRD, SEM and electrochemical tests. Effort to simultaneously doped LiNiO₂ with Co-Ti-Mg has been tried to improve the cathode performance. The results show that co-doping definitely has a large beneficial effect in increasing the capacity (182.7mAh/g of the first discharge capacity for  LiNi_0.85Co_0.10(TiMg)_0.025O_{2 …}

Application Of Carbon Paste Electrode On The Electrogenerative-Leaching Process Of Sulfide Minerals, Shao-Fen Wang, Zheng Fang, Yun-Yan Wang

Journal of Electrochemistry

The cyclic voltammetry curves of sulfide mineral electrodes or corresponding carbon paste electrodes in NaCl electrolytes have been obtained in this study. The experimental results indicate that acetylene black (revealed) the electro-catalytic propertyin the electrogenerative-leaching process of sulfide minerals. The output currentand potential of carbon paste electrodes were increased to some degrees while the activation energies were lower.

Preparation Of Poly (Bromophenol Blue) Modified Glassy Carbon Electrode And Its Electrocatalytic Activity, Wei Chen, Hong-Bin Luo, Xin-Hua Lin

Journal of Electrochemistry

A film of poly (bromophenol blue) was formed on a glassy carbon electrode by using cyclic voltammetry. A stable film could be obtained with a potential range from -1.0 V to +1.8 V (vs.Ag/AgCl). The experimental results showed that the poly (bromophenol blue) modified glassy carbon electrode could catalyse the oxidation of ascorbic acid. It decreased the oxidation potential by about 270mV but increased the peak current. Meanwhile, this electrode showed a good linear current response for the ascorbic acid range from 2.5 to 250 (g/mL).

Electrochemical Properties Of Polymeric Gel Electrolyte With Gbl/Ec As Plasticizers, Yu-Wen Liu, Yong Zhang, Xiao-Long Li, Qi-Ping Gu, Cui-Fen Zhang, Yu-Dong Huang

Journal of Electrochemistry

Polymeric gel electrolytes (GPE) based on PMMA and PVDF-HFP were prepared using the binary mixtures of γ-butyrolactone (GBL) and ethylene carbonate (EC) as plasticizers. The ionic transport properties and electrochemical stability were studied. The room temperature conductivity reached 1.2 mS·cm^-1, electrochemical stability window exceeded 4.5V. The interfacial stability between GPE and lithium electrode was also investigated. The lithium metal polymer battery (LMPB) prepared with the GPE showed better charge and discharge life cycle when the the lithium metal electrode was treated with 1,4-dioxane.

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO₂/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO₂/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L^-1, and the phenol concentrations in the purified …

Texture Formation In Fept Thin Films Via Thermal Stress Management, P. Rasmussen, X. Rui, Jeffrey E. Shield

Materials Research Science and Engineering Center: Faculty Publications

The transformation variant of the fcc to fct transformation in FePt thin films was tailored by controlling the stresses in the thin films, thereby allowing selection of in- or out-of-plane c-axis orientation. FePt thin films were deposited at ambient temperature on several substrates with differing coefficients of thermal expansion relative to the FePt, which generated thermal stresses during the ordering heat treatment. X-ray diffraction analysis revealed preferential out-of-plane c-axis orientation for FePt films deposited on substrates with a similar coefficients of thermal expansion, and random orientation for FePt films deposited on substrates with a very low coefficient of …

High-Anisotropy Nanocluster Films For High-Density Perpendicular Recording, David J. Sellmyer, Minglang Yan, Yinfan Xu, Ralph Skomski

Materials Research Science and Engineering Center: Faculty Publications

This paper reports results on the synthesis and magnetic properties of L1₀:X nanocomposite films, where L1₀ = FePt, CoPt, and X = C, Ag, etc. Two fabrication methods are discussed: nonepitaxial growth of oriented perpendicular media, and monodispersed nanoparticle-assembled films grown with a gas-aggregation source. The magnetic properties are controllable through variations in the nanocluster properties and nanostructure. The films show promise for development as recording media at extremely high areal densities.

Ferrocement Sandwich And Hollow Core Panels For Floor And Wall Construction, Hassan Mohammed Gaafar

Archived Theses and Dissertations

No abstract provided.

Improved Compressed Earth Blocks, Tarek Mahmoud Ahmed Elgindy

Archived Theses and Dissertations

Bricks and blocks, being two of the most important building materials in our construction field, can be made out of different materials, most popular of which are earthen materials. Ancient civilizations used earthen materials as a cheap and easy way to make bricks from which they built their houses and shelters. Ancient Egyptians used "mud" (which is technically silt and clay) to make bricks which we call now adobe. These days, despite the low cost of adobe it is loosing grounds in the construction of housing because of its very low compressive strength and poor durability against weathering. Accordingly, cement …

The Feasibility Of Micromachined Dynamic Resonant Beam Coriolis True Mass Flow Meter, Sang Hwui Lee

Dissertations

The technological advances of micro-electro-mechanical systems (MEMS) in the past two decades have been remarkable for innovations in microfluidic systems as well as automotive applications such as pressure sensors and accelerometers. MEMS flow sensing has emerged as a field of interest in microfluidics, with a variety of sensing methods being miniaturized, such as thermal anemometry, ultrasonic sensing and flow measurement based on the Coriolis effect. Coriolis sensing is particularly attractive since, unlike most other methods which provide volumetric flow information, Coriolis sensing is capable of providing a direct, true mass flow measurement. Because of this advantage, Coriolis flow sensing has …

In Vitro Drug Delivery Based On A Porous Membrane-Based Aqueous-Organic Partitioning System And Its Enhancements Through Mouse Skin, Qiuxi Fan

Dissertations

Novel approaches for transdermal drug delivery (TDD) based on a porous membrane-based aqueous-organic partitioning system have been investigated and successful deliveries were observed. Doxycycline hydrochloride (HCl), a polar antibiotic drug with a relatively large molecule weight (MW: 480.1) was studied as a basic model agent. Its controlled release using this technique was studied first. Satisfactory release profiles demonstrate the practical potential of such a system to achieve useful controlled release rates. The enhancer linoleic acid was essential to successful release using a mouse skin beneath a porous polymeric membrane. The transport rates of smaller molecules e.g., caffeine and nicotine from …

Impurity-Assisted Interlayer Exchange Coupling Across A Tunnel Barrier, Mikhail Ye Zhuravlev, Evgeny Y. Tsymbal, A. V. Vedyayev

Materials Research Science and Engineering Center: Faculty Publications

Localized impurity or defect states in the insulating barrier layer separating two ferromagnetic films affect dramatically the interlayer exchange coupling (IEC), making it significantly stronger compared to perfect barriers. We demonstrate that the impurity-assisted IEC becomes antiferromagnetic if the energy of the impurity states matches the Fermi energy and that the coupling strength decreases with temperature. These results explain available experimental data on the IEC across tunnel barriers.

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (August 2004 – October 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), Los Alamos National Laboratory (LANL) and Idaho State University (ISU) is to evaluate the effect of silicon (Si) content on the corrosion behavior and radiation-induced embrittlement of martensitic stainless steels having chemical compositions similar to that of the modified 9Cr-1Mo steel. Recent studies at LANL involving Alloy EP-823 of different Si content have demonstrated that increased Si content in this alloy may enhance the corrosion resistance in molten lead-bismutheutectic (LBE). Since very little data exists in the open literature on the beneficial effect of Si …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (September 01 – November 30, 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

Accomplishments:

● A technical paper titled “Residual Stress Characterization in Structural Materials by Destructive and Nondestructive Techniques” has been accepted for publication in the Journal of Materials Engineering and Performance, ASM International, Ohio.

● The PAS method has been applied to develop calibration curves for line shape parameters (S and T) using unstressed and stressed (different magnitude) tensile specimens of martensitic stainless steels. These curves will enable the determination of residual stresses in plastically-deformed materials once the magnitude of S or T parameter is determined by the PAS technique.

● The tensile and welded specimens have been irradiated by low …

A Three Dimensional Finite Element Model For Emergency Response, Xiuling Wang, Darrell W. Pepper, Yitung Chen, Sean Hsieh

Mechanical Engineering Faculty Research

No abstract provided.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii, Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities in the no-cost extension period. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. In December of 2005, the software for the particle positioning detector was finally up …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 2, Dhanesh Chandra

Publications (YM)

This report encompasses the work done for second quarter in accordance to cooperative agreement of UCCSN for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the objective of which was proposed earlier, to conduct corrosion research and predict the durability of rock-bolts and other underground metallic roof supports. We have recently started working on oxidation tests using Thermogravimetric Analyzer, stress corrosion cracking/hydrogen embrittlement studies on rock bolts, other support materials including bench mark materials. In this quarterly report we will discuss “Dry” oxidation of steels and other …

The Grain Size And Microstructure Of Jet-Electroplated Damascene Copper Films, Stacy H. Gleixner, Andrew Tzanavaras, Gregory Young

Faculty Publications

Electroplated damascene copper is rapidly replacing aluminum-copper alloys for on-chip interconnect metallization in advanced ultralarge scale integrated (ULSI) semiconductor devices. In addition to a high degree of (111) crystallographic texture, large defect-free grains are desired to enhance the performance and reliability of copper interconnects in such devices. The brightening additive level and dc current density of electroplating baths are two parameters that affect the process gap-filling capability and the degree of additive incorporation in these copper films. Additive incorporation can inhibit grain growth during the room-temperature recrystallization process and therefore affect the final grain size in electroplated copper films. This …