Materials Science and Engineering Commons^™

Efficiency In Steel Melting: Opportunities And Progress, Kent D. Peaslee, Semen Naumovich Lekakh, Von Richards, Jay Triplett

Materials Science and Engineering Faculty Research & Creative Works

This paper summarizes the findings from a study of melting efficiency in steel foundries and provides examples of material and energy savings from improvements in technology and melting practices. This study is based on information gathered at 19 Steel Founders Society of America member foundries and includes a combination of historical data and industrial measurements by the research team. Information and data were collected on the type of melting equipment, melting practices, energy use and ladle practices. The data was statistically analyzed using STATGRAPHICS commercial software. A multiple regression analysis allowed evaluation of the influence of the melting furnace (type, …

Elevated Temperature Deformation Behavior Of Nanostructured Al-Ni-Gd-Fe Alloys, X. L. Shi, Rajiv S. Mishra, T. J. Watson

Materials Science and Engineering Faculty Research & Creative Works

The elevated temperature deformation behavior of nanostructured Al89Ni3Gd7Fe1 alloy was characterized. Tensile strength was 760 MPa at 373 K. Ductility of the alloy increases with increasing strain rate at 573 K. At high temperatures (623-673 K), the operative deformation mechanism is dislocation-climb controlled.

Continuous Solidification Of Yba2cu3o7−X By Isothermal Undercooling, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Growth kinetics and microstructural development of single crystal YBa₂Cu₃O_7−x (Y123) superconductors, prepared by a melt texturing method under isothermal undercooling conditions, were investigated. At small undercooling, ΔT = 6 K, the initial growth of Y123 crystal was terminated at a size of ∼8 mm × 8 mm in the semisolid phase before the entire sample was fully solidified through the peritectic reaction. With incremental increase of ΔT, the growth of the crystal continued so that the whole sample (22 mm diameter and 8 mm thickness) solidified as a single crystal. Termination of the crystal growth …

Thermal And Mechanical Properties Of Polyethylene-Polypropylene Blends, Rania Omar Akkad

Theses

The thermal and mechanical characteristics of thermally treated and untreated pure polyethylene (PE), pure polypropylene (PP) and their blends were investigated. Injection-moulded samples containing 100:00,75:25,50:50,25:75 and 00:100 weight percentage of PE:PP, were prepared and thermally treated at 100°C for 0, 2, 4, 7, 14 days. The treated samples were subjected to differential scanning calorimetry (DSC), thermogravimetry (TG & DTG), infrared spectral analysis (IR) and tensile tests in order to study the effect of thermal treatment and blending ratios on their thermal and mechanical properties. The results indicate that addition of PE causes the melting temperature (T_m) of PP …

Mechanics Of Composite Materials In Fuel Cell Systems, Kenneth Reifsnider, Xinyu Huang, G. Ju, Matthew Feshler, K. An

Faculty Publications

The science and technology that are fundamental to the concept of composite materials are also the foundation for the construction and function of fuel cells and fuel cell systems. The present paper outlines this relationship in the context of the physics and chemistry that are enabled by the specific selection and arrangement of constituents of the “functional composite” fuel cell. General principles of operation are described, and fundamental issues are defined that must be addressed by the composites community if the fuel cell science and engineering is to advance. Examples of several types of functional composite fuel cells are presented, …

Investigation Of Ferroelectricity In Newly Synthesized Nitrile Polymer Systems, Matt Poulsen, Stephen Ducharme, Alexander V. Sorokin, Sahadeva Reddy, James M. Takacs, Y. Wen, Jihee Kim, Shireen Adenwalla

Stephen Ducharme Publications

The ferroelectric and piezoelectric properties of newly synthesized polymer systems have been studied. To date PVDF and its copolymers P(VDF-TrFE) have provided the bulk of the knowledge pertaining to ferroelectricity in polymers. Recently, ultrathin ferroelectric films of P(VDF-TrFE) 70:30 have been fabricated using the Langmuir-Blodgett technique [4]. In this study, various new polymers have been synthesized by chemically altering the PVDF structure. This alteration was performed in order to enhance the amphiphilic nature of the polymer and thus improve the LB film quality and control. Various chemical groups have been used to replace the electropositive hydrogen and electronegative fluorine found …

Boron-Rich Semiconducting Boron Carbide Neutron Detector, Andrew D. Harken, Ellen E. Day, Brian W. Robertson, Shireen Adenwalla

Shireen Adenwalla Papers

Data on the neutron detection capabilities of a variety of boron carbide/Si heterojunction diodes is presented. The pulse height spectra are compared with previously measured conversion layer devices and the variations in shape and position of the peaks are discussed.

Deuterium Nmr Studies Of Segmental Dynamics Of Anopore-Adsorbed Poly(Methyl Acrylate), Macduff O. Okuom, Frank D. Blum

Chemistry Faculty Research & Creative Works

Studies of segmental dynamics of polymers at interfaces provide a basis for understanding the properties of composite materials. Interfacial phenomena in multi-phase systems need to be understood as devices made from multi-phase polymeric systems become smaller. Various techniques have been used to investigate interfacial polymers at the air-polymer-solid interface; for example, ellipsometry,1 X-ray,2 and neutron reflectometry.3 These techniques typically characterize the structure (often the thickness) of the polymer layer and are normally used to determine the glass-transition temperature (Tg) through a break in the thicknesstemperature curve. There have been a few reports where the dynamics of polymers at the surface-air …

Investigations Of The Kinetics Of Liquid Droplets On Soil Substrates Using A Novel Approach: Contact Ratio, Abdelhafiz “Moh’D Adnan” Herbawi

Theses

In view of young’s equation, in which the contact angle “ϑ” and the liquid surface tension γ_lv are the only measurable parameters, the contact angle has been widely conceived as a thermodynamic quantity. Accordingly “ϑ” has been the main focus of most theoretical and experimental investigations. The rate of change in the contact angle has been commonly used as the relevant parameter of spreading dynamics in spite of difficulties associated with contact angle measurements that are well recognized in the literature. Considering that the velocity of the contact line is the pertinent quantity for spreading, it is therefore reasonable …

Microwave Processing Of Fiber Reinforced Composites (Optimization Of Glass Reinforced Epoxy Curing Process), Mohamed Osama Ali

Theses

Microwave curing of polymer matrix composites has proven to be an attractive substitute for conventional thermal curing. Industrial applications are currently developed including telecommunications, aerospace, food industry, enhancement concrete setting, composites manufacturing, and many others. Many universities and research centers around the globe are endeavoring to make use of this technology to the most. Common research objectives include homogeneity of the cure, the acceleration of cure kinetics, cure reaction mechanism, and enhancement of mechanical properties. In order to efficiently utilize this form of energy, precise control over power, temperature, and time were applied to achieve set goals: reduce cure time …

Effect Of Bond Thickness On Lifetime Of Adhesive Joints, Ehab Mohammed El-Said El-Refaai Shehab

Theses

The aim of this research was to study the effect of bond thickness on the fracture energy and the lifetime of an adhesively bonded system and develop a model to predict the lifetime of adhesive joints. An approach based on fracture mechanics was employed to assess aluminum/epoxy bond lifetime. An experimental investigation was carried out using double cantilever beam (DCB) specimens with various bond thicknesses under mode 1.

This study describes an approach to predict the rate of crack propagation using Paris' power law. The approach used elevated temperatures to accelerate the crack propagation under constant loads. The elevated temperatures …

Ductile Crack Growth Emanating From Sharp Notes In A Low Alloy Steel, Aladdin I. Abu-Assi

Theses

Stable crack growth behavior emanating from a sharp notch is investigated. Material chosen for tests was EN 34 NiCrMo6 low alloy steel (akin to 4340/4330). Tests were carried out on CT specimens for various angles and ratios to obtain load vs, load-line displacement, Ρ-Δ_LL, curves. Experimental results were analyzed. A normalization approach of Ρ-Δ_{LL curves has been attempted and all experimental curves were represented as a single characteristic curve. Such approach has been also applied on experimental data available from other experimental investigations and results were encouraging, as it may address transferability issue. Fracture surfaces were …}

Investigation Of Epoxy Resin Spreading On Glass Surfaces, Haneen Nemer Al-Dahdooh

Theses

The spreading of a small epoxy resin droplet (l.5tL) on a glass surface was examined with the objective of developing a new type of hydrophobic polymer coated glass which has the ability to reduce heat gain inside a building. The study covered three main aspects; the spreading kinetics of epoxy resin on a glass surface, the hydophopicity of the developed polymer-coated glass surface, and the reduction of solar radiation of this surface, As wettability and spreading phenomena arc a fundamental prerequisite for coating, the spreading kinetics of different curing agent concentrations (15:200, 18:200, 21:200) of epoxy resin on the glass …