Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Faculty Research & Creative Works

Discipline
Keyword
Publication Year

Articles 361 - 390 of 1006

Full-Text Articles in Materials Science and Engineering

Femtosecond Laser-Matter Interactions In Ternary Zinc Phosphate Glasses, J. Hernandez-Rueda, N. W. Troy, P. Freudenberger, Richard K. Brow, D. M. Krol Jan 2018

Femtosecond Laser-Matter Interactions In Ternary Zinc Phosphate Glasses, J. Hernandez-Rueda, N. W. Troy, P. Freudenberger, Richard K. Brow, D. M. Krol

Materials Science and Engineering Faculty Research & Creative Works

We investigate the interaction of ultrashort laser pulses with ternary zinc phosphate glasses. We explore the viability of ten different glass compositions with different levels of alumina to inscribe optical waveguides via the fs-laser direct writing technique, finding that only samples with [O]/[P] ratios of 3.25 are suitable candidates. We also test a zinc magnesium phosphate glass to fabricate waveguide Bragg gratings in order to generate filters and mirrors with specific spectral properties. Confocal Raman spectroscopy inspection shows that laser-damaged material exhibits a relative intensity decrease and a subtle blue-shift on the 1209 cm-1 Raman peak, which implies a relative …

Go to article

Effect Of Thickness On The Structure And Corrosion Performance Of Sputtered Ce-Al-O Coatings On Al 2024-T3 Alloy Substrates, Yuanyuan Liu, Jiamu Huang, Lilu Qin, James B. Claypool, Matthew J. O'Keefe, Yiming Jiang Jan 2018

Effect Of Thickness On The Structure And Corrosion Performance Of Sputtered Ce-Al-O Coatings On Al 2024-T3 Alloy Substrates, Yuanyuan Liu, Jiamu Huang, Lilu Qin, James B. Claypool, Matthew J. O'Keefe, Yiming Jiang

Materials Science and Engineering Faculty Research & Creative Works

Ce-Al-O coatings with thicknesses between ca. 136 nm and 1094 nm were deposited on Al 2024-T3 alloy substrates using magnetron co-sputtering of independent Al and CeO2 targets. The Ce-Al-O coatings with thicknesses from ca. 136 nm to 490 nm were compact, dense, and did not have distinct X-ray diffraction peaks. The ca. 1094 nm thick Ce-Al-O coating exhibited a columnar-textured outer layer ∼700 nm thick and a dense, ∼390 nm thick inner layer. X-ray photoelectron spectroscopy analysis revealed that the Ce-Al-O coatings contained Ce (III) species, and that the Al/Ce atomic ratio decreased with increasing coating thickness. Electrochemical corrosion data …

Go to article

A Simple Model For Elastic-Plastic Contact Of Granular Geomaterials, Jian Wang, Qimin Li, Changwei Yang, Yidan Huang, Caizhi Zhou Jan 2018

A Simple Model For Elastic-Plastic Contact Of Granular Geomaterials, Jian Wang, Qimin Li, Changwei Yang, Yidan Huang, Caizhi Zhou

Materials Science and Engineering Faculty Research & Creative Works

We propose a simple elastic-plastic contact model by considering the interaction of two spheres in the normal direction, for use in discrete element method (DEM) simulations of geomaterials. This model has been developed by using the finite element method (FEM) and nonlinear fitting methods, in the form of power-law relation of the dimensionless normal force and displacement. Only four parameters are needed for each loading-unloading contact process between two spheres, which are relevant to material properties evaluated by FEM simulations. Within the given range of material properties, those four parameters can be quickly accessed by interpolating the data appended or …

Go to article

Factors Affecting The Evolution Of Inclusion Populations During Steelmaking And Casting Processes, Obinna Adaba, Laura Bartlett, Mingzhi Xu, Ronald J. O'Malley Dec 2017

Factors Affecting The Evolution Of Inclusion Populations During Steelmaking And Casting Processes, Obinna Adaba, Laura Bartlett, Mingzhi Xu, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Investigations into the evolution of inclusion populations during ladle processing and continuous casting are reviewed. Details of the steelmaking practices employed in BOP and EAF steelmaking have been observed to have a strong influence on the size distribution, quantity, composition, phases and morphology of the final inclusion population delivered to the caster. Examples of the effects of different processing paths on the evolution of inclusion populations are presented. The importance of preexisting inclusion populations on the formation and removal of new inclusion populations is also reviewed and discussed.

Go to article

Nanograin Size Effects On The Strength Of Biphase Nanolayered Composites, Sixie Huang, Irene J. Beyerlein, Caizhi Zhou Dec 2017

Nanograin Size Effects On The Strength Of Biphase Nanolayered Composites, Sixie Huang, Irene J. Beyerlein, Caizhi Zhou

Materials Science and Engineering Faculty Research & Creative Works

In this work, we employ atomic-scale simulations to uncover the interface-driven deformation mechanisms in biphase nanolayered composites. Two internal boundaries persist in these materials, the interlayer crystalline boundaries and intralayer biphase interfaces, and both have nanoscale dimensions. These internal surfaces are known to control the activation and motion of dislocations, and despite the fact that most of these materials bear both types of interfaces. From our calculations, we find that the first defect event, signifying yield, is controlled by the intralayer spacing (grain size, d), and not the intralayer biphase spacing (layer thickness, h). The interplay of two internal sizes …

Go to article

Nonlinear Optical Properties Of Gesbs Chalcogenide Waveguides, Ju Won Choi, Byoung Uk Sohn, George F.R. Chen, Dawn T.H. Tan, Zhaohong Han, Lionel C. Kimerling, Charmayne Smith (Lonergan), Kathleen A. Richardson, Anuradha M. Agarwal Nov 2017

Nonlinear Optical Properties Of Gesbs Chalcogenide Waveguides, Ju Won Choi, Byoung Uk Sohn, George F.R. Chen, Dawn T.H. Tan, Zhaohong Han, Lionel C. Kimerling, Charmayne Smith (Lonergan), Kathleen A. Richardson, Anuradha M. Agarwal

Materials Science and Engineering Faculty Research & Creative Works

We characterize the nonlinear optical properties of GeSbS chalcogenide glasses with fiber-based experiments. A waveguide nonlinear parameter of 7 W-1/m and nonlinear refractive index of 3.71 x 10-18 m2/W are estimated by self-phase modulation. A GeSbS waveguide could also generate a supercontinuum from 1280 to 2120 nm at the -30 dB level for maximum coupled power of 340 W, showing a 14-fold spectral broadening of the input spectrum explained by cascaded stimulated Raman scattering.

Go to article

Effective Mechanical Properties Of Multilayer Nano-Heterostructures, T Mukhopadhyay, A Mahata, S Adhikari, Mohsen Asle Zaeem Nov 2017

Effective Mechanical Properties Of Multilayer Nano-Heterostructures, T Mukhopadhyay, A Mahata, S Adhikari, Mohsen Asle Zaeem

Materials Science and Engineering Faculty Research & Creative Works

Two-dimensional and quasi-two-dimensional materials are important nanostructures because of their exciting electronic, optical, thermal, chemical and mechanical properties. However, a single-layer nanomaterial may not possess a particular property adequately, or multiple desired properties simultaneously. Recently a new trend has emerged to develop nano-heterostructures by assembling multiple monolayers of different nanostructures to achieve various tunable desired properties simultaneously. For example, transition metal dichalcogenides such as MoS2 show promising electronic and piezoelectric properties, but their low mechanical strength is a constraint for practical applications. This barrier can be mitigated by considering graphene-MoS2 heterostructure, as graphene possesses strong mechanical properties. We …

Go to article

Design And Fabrication Of Functionally Graded Material From Ti To Γ-Tial By Laser Metal Deposition, Xueyang Chen, Lei Yan, Joseph William Newkirk, Frank W. Liou Aug 2017

Design And Fabrication Of Functionally Graded Material From Ti To Γ-Tial By Laser Metal Deposition, Xueyang Chen, Lei Yan, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

Functionally graded material (FGM) is one kind of advanced material characterized by a gradual change in properties as the position varies. The spatial variation of compositional and microstructure over volume is aimed to control corresponding functional properties. In this research, when 100% γ-TiAl was directly deposited on pure Ti substrate, cracks were formed within the γ-TiAl layer. Then a six-layer crack-free functionally graded material of Ti/TiAl was designed and fabricated by laser metal deposition (LMD) method, with composition changing from pure Ti on one side to 100% γ-TiAl on the other side. The fabricated FGM was characterized for material properties …

Go to article

Studying Chromium And Nickel Equivalency To Identify Viable Additive Manufacturing Stainless Steel Chemistries, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley Aug 2017

Studying Chromium And Nickel Equivalency To Identify Viable Additive Manufacturing Stainless Steel Chemistries, Zachary T. Hilton, Joseph William Newkirk, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Chromium and nickel equivalency modeling has long been used in welding to determine the weldability of steel chemistries. A study was conducted to determine the applicability of Cr-Ni modeling to the additive manufacturing process. Many AM methods involve rapid solidification of small melt pools, similar to welding. Chemistries with varying Cr/Ni ratios were selected for use in a selective laser melting process and modeled using known models. Initial results indicate that the standard "safe welding zone" may not directly apply to additive manufacturing. The capability to build with chemistries outside the weldability “safe zone” could result in improved and varied …

Go to article

Aluminum Matrix Syntactic Foam Fabricated With Additive Manufacturing, M. Spratt, Joseph William Newkirk, K. Chandrashekhara Aug 2017

Aluminum Matrix Syntactic Foam Fabricated With Additive Manufacturing, M. Spratt, Joseph William Newkirk, K. Chandrashekhara

Materials Science and Engineering Faculty Research & Creative Works

Syntactic foams are lightweight structural composites with hollow reinforcing particles embedded in a soft matrix. These materials have applications in transportation, packaging, and armor due to properties such as relatively high specific stiffness, acoustic dampening, and impact absorption. Aluminum matrices are the most widely studied of metal matrix syntactic foams, but there is little to no research in regards to processing the foams with additive manufacturing. It is theorized that the fast cooling rates and limited kinetic energy input of additive could reduce two issues commonly associated with processing syntactic foams: microsphere flotation in the melt and microsphere fracture during …

Go to article

Effects Of Area Fraction And Part Spacing On Degradation Of 304l Stainless Steel Powder In Selective Laser Melting, Cairlin S. Kriewall, Austin T. Sutton, Sreekar Karnati, Joseph William Newkirk, Ming-Chuan Leu Aug 2017

Effects Of Area Fraction And Part Spacing On Degradation Of 304l Stainless Steel Powder In Selective Laser Melting, Cairlin S. Kriewall, Austin T. Sutton, Sreekar Karnati, Joseph William Newkirk, Ming-Chuan Leu

Materials Science and Engineering Faculty Research & Creative Works

In selective laser melting (SLM) systems, a large portion of powder remains unconsolidated and therefore recycling powder could make SLM more economical. Currently, a lack of literature exists specifically targeted at studying the reusability of powder. Furthermore, the definition of powder reusability is complex since powder degradation depends on many factors. The goal of the current research is to investigate the effects of area fraction and part spacing on the degradation of 304L powder in SLM. An experimental study was conducted where various area fractions and part distances were chosen and powder characterization techniques for determination of particle size distributions, …

Go to article

Effects Of Iron Concentration And Redox States On Failure Of Boron-Free E-Glass Fibres Under Applied Stress In Different Conditions, Qingwei Wang, Richard K. Brow, Hong Li, Erica Ann Ronchetto Aug 2017

Effects Of Iron Concentration And Redox States On Failure Of Boron-Free E-Glass Fibres Under Applied Stress In Different Conditions, Qingwei Wang, Richard K. Brow, Hong Li, Erica Ann Ronchetto

Materials Science and Engineering Faculty Research & Creative Works

Hydrolysis resistance of boron-free E-glass fiber with different total iron oxide (Fe2O3) concentrations, iron redox index and durations of fiber ageing up to 180 days at 50◦C with 50% relative humidity (RH) was studied. The effect of ageing on the fibre failure measured in two different test environments was examined by using two-point bending method. Based on the differences in failure strains of the fibres obtained from the two conditions as a function of ageing time, the Griffith theory of solid fracture was applied to estimate glass surface energy difference in ageing conditions. The results showed …

Go to article

Homogenization Of Plastic Deformation In Heterogeneous Lamella Structures, Rui Yuan, Irene J. Beyerlein, Caizhi Zhou Jul 2017

Homogenization Of Plastic Deformation In Heterogeneous Lamella Structures, Rui Yuan, Irene J. Beyerlein, Caizhi Zhou

Materials Science and Engineering Faculty Research & Creative Works

It has been shown that unlike its constituent nanocrystalline (NC) phase, a heterogeneous lamella (HL) composite comprising NC and coarse-grain layers exhibits greatly improved ductility. To understand the origin of this enhancement, we present a 3D discrete dislocation, crystal plasticity finite element model to study the development of strains across this microstructure. Here we show that the HL structure homogenizes the plastic strains in the NC layer, weakening the effect of strain concentrations. These findings can provide valuable insight into the effects of material length scales on material instabilities, which is needed to design heterogeneous structures with superior properties.

Go to article

Effects Of Specimen Size And Yttria Concentration On Mechanical Properties Of Single Crystalline Yttria-Stabilized Tetragonal Zirconia Nanopillars, Ning Zhang, Mohsen Asle Zaeem Jul 2017

Effects Of Specimen Size And Yttria Concentration On Mechanical Properties Of Single Crystalline Yttria-Stabilized Tetragonal Zirconia Nanopillars, Ning Zhang, Mohsen Asle Zaeem

Materials Science and Engineering Faculty Research & Creative Works

The nanoscale plastic deformation of yttria-stabilized tetragonal zirconia (YSTZ) is highly dependent on the crystallographic orientations, i.e., dislocation is induced when the loading direction is 45° tilted to {111} and {101} slip planes, while tetragonal to monoclinic phase transformation dominates the plastic deformation when loading direction is perpendicular to the slip planes. This study investigates the effects of specimen size and yttria concentration on the mechanical response of single crystalline YSTZ nanopillars. Through uniaxial compression test, the smaller-is-stronger phenomenon is revealed in nanopillars deformed through a dislocation motion mechanism. Serrated stacking faults are observed in the smallest nanopillar, while neat …

Go to article

Nanostructured Dielectric Materials For High Energy Density Multi Layer Ceramic Capacitors, Fatih Dogan May 2017

Nanostructured Dielectric Materials For High Energy Density Multi Layer Ceramic Capacitors, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

A high energy density multilayer ceramic capacitor, having at least two electrode layers and at least one substantially dense polycrystalline dielectric layer positioned therebetween. The at polycrystalline dielectric layer has an average grain size of less than about 300 nanometers, a particle size distribution of between about 150 nanometers and about 3 micrometers, and a maximum porosity of about 1 percent. The dielectric layer is selected from the group including TiO2, BaTiO3, Al2O3, ZrO2, lead zirconium titanate, and combinations thereof and has a breakdown strength of at least about 1100 …

Go to article

The Role Of Ceramic And Glass Science Research In Meeting Societal Challenges: Report From An Nsf-Sponsored Workshop, Katherine T. Faber, Tewodros Asefa, Monika Backhaus-Ricoult, Richard K. Brow, Julie Y. Chan, Shen Dillon, William Fahrenholtz, For Full List Of Authors, See Publisher's Website. May 2017

The Role Of Ceramic And Glass Science Research In Meeting Societal Challenges: Report From An Nsf-Sponsored Workshop, Katherine T. Faber, Tewodros Asefa, Monika Backhaus-Ricoult, Richard K. Brow, Julie Y. Chan, Shen Dillon, William Fahrenholtz, For Full List Of Authors, See Publisher's Website.

Materials Science and Engineering Faculty Research & Creative Works

Under the sponsorship of the U.S. National Science Foundation, a workshop on emerging research opportunities in ceramic and glass science was held in September 2016. Reported here are proceedings of the workshop. The report details eight challenges identified through workshop discussions: Ceramic processing: Programmable design and assembly; The defect genome: Understanding, characterizing, and predicting defects across time and length scales; Functionalizing defects for unprecedented properties; Ceramic flatlands: Defining structure-property relations in free-standing, supported, and confined two-dimensional ceramics; Ceramics in the extreme: Discovery and design strategies; Ceramics in the extreme: Behavior of multimaterial systems; Understanding and exploiting glasses and melts under …

Go to article

Effects Of Yttria Concentration And Microstructure On Electric Breakdown Of Yttria Stabilized Zirconia, Oratai Jongprateep, Vladimir Petrovsky, Fatih Dogan Apr 2017

Effects Of Yttria Concentration And Microstructure On Electric Breakdown Of Yttria Stabilized Zirconia, Oratai Jongprateep, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Ceramic materials have great potentials for capacitor application. However, low breakdown strength of the materials remains a key challenge for development of high-performance capacitors. In this study, yttria stabilized zirconia (YSZ) were fabricated and tested for breakdown strength. YSZ samples with 3, 8, and 10 mol% yttria were carefully processed to control grain size and porosity level. Experimental results revealed that breakdown strength as high as 2 MV/cm could be achieved. The breakdown strength was not significantly affected by porosity level, but it was by yttria concentration. Relationship among yttria concentration, residual porosity and breakdown strength is discussed in this …

Go to article

Controlling Calcium Compound Formation In Biocompatible Materials For Tissue Regeneration And Repair In Mammals, Steven B. Jung, D. E. Day Feb 2017

Controlling Calcium Compound Formation In Biocompatible Materials For Tissue Regeneration And Repair In Mammals, Steven B. Jung, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

A biocompatible composition for tissue repair or regeneration in mammals comprising one or more glass former compounds selected from the group consisting of B2O3, P2O5, and SiO2 and director elements selected from the group consisting of Cu, Sr, Zn, Fe, Mn, Cr, V, Nb, Mo, W, Ba, Co, S, Al, Ti, Y, Mg, Si and/or Ni to promote in vivo calcium compound formation of calcium carbonate or other calcium compounds other than hydroxyapatite. Upon direct application of the biocompatible composition to a mammalian host, calcium carbonate or other calcium compounds other …

Go to article

Scaffold For Tissue Regeneration In Mammals, D. E. Day, Steven B. Jung, Roger F. Brown Feb 2017

Scaffold For Tissue Regeneration In Mammals, D. E. Day, Steven B. Jung, Roger F. Brown

Materials Science and Engineering Faculty Research & Creative Works

A three-dimensional scaffold with interconnected pores for repair of tissue comprising a scaffold body for structural support of the tissue scaffold, where the scaffold body comprises scaffold body components bonded to each other and made from component materials comprising about 40 to about 90 wt % B2O3, and two or more other oxides, wherein the scaffold body has a porosity between about 15 and about 90 vol %.

Go to article

Super-Strong Materials For Temperatures Exceeding 2000 ⁰C, Laura Silvestroni, Hans Joachim Kleebe, William Fahrenholtz, Jeremy Lee Watts Jan 2017

Super-Strong Materials For Temperatures Exceeding 2000 ⁰C, Laura Silvestroni, Hans Joachim Kleebe, William Fahrenholtz, Jeremy Lee Watts

Materials Science and Engineering Faculty Research & Creative Works

Ceramics based on group IV-V transition metal borides and carbides possess melting points above 3000⁰C, are ablation resistant and are, therefore, candidates for the design of components of next generation space vehicles, rocket nozzle inserts, and nose cones or leading edges for hypersonic aerospace vehicles. As such, they will have to bear high thermo-mechanical loads, which makes strength at high temperature of great importance. While testing of these materials above 2000⁰C is necessary to prove their capabilities at anticipated operating temperatures, literature reports are quite limited. Reported strength values for zirconium diboride (ZrB2) ceramics can exceed 1 GPa …

Go to article

Control Of Columnar To Equiaxed Transition In Solidification Macrostructure Of Austenitic Stainless Steel Castings, Semen Naumovich Lekakh, Ronald J. O'Malley, Mark C. Emmendorfer, Brenton Hrebec Jan 2017

Control Of Columnar To Equiaxed Transition In Solidification Macrostructure Of Austenitic Stainless Steel Castings, Semen Naumovich Lekakh, Ronald J. O'Malley, Mark C. Emmendorfer, Brenton Hrebec

Materials Science and Engineering Faculty Research & Creative Works

Solidification macrostructure is of great importance for the properties and the quality of castings made from austenitic grade stainless steels (ASS) because there are limited options to change as-cast macrostructure in the solid condition. A typical cast macrostructure of ASS has a fine surface chilled zone followed by an elongated dendrite zone, columnar to equiaxed transition (CET) zone, and centrally located equiaxed crystals. Several castings from ASS were produced to determine the effects of casting geometry, chilling, and grain refinement on CET. The transient thermal field in solidified heavy castings was simulated and used to determine an isotherm velocity (V) …

Go to article

Nonlinear Characterization Of Gesbs Chalcogenide Glass Waveguides, Ju Won Choi, Zhaohong Han, Byoung Uk Sohn, George F.R. Chen, Charmayne Smith (Lonergan), Lionel C. Kimerling, Kathleen A. Richardson, Anuradha M. Agarwal, Dawn T.H. Tan Dec 2016

Nonlinear Characterization Of Gesbs Chalcogenide Glass Waveguides, Ju Won Choi, Zhaohong Han, Byoung Uk Sohn, George F.R. Chen, Charmayne Smith (Lonergan), Lionel C. Kimerling, Kathleen A. Richardson, Anuradha M. Agarwal, Dawn T.H. Tan

Materials Science and Engineering Faculty Research & Creative Works

GeSbS ridge waveguides have recently been demonstrated as a promising mid - infrared platform for integrated waveguide - based chemical sensing and photodetection. To date, their nonlinear optical properties remain relatively unexplored. In this paper, we characterize the nonlinear optical properties of GeSbS glasses, and show negligible nonlinear losses at 1.55 μm. Using self - phase modulation experiments, we characterize a waveguide nonlinear parameter of 7 W-1/m and nonlinear refractive index of 3.71 x 10-18 m2/W. GeSbS waveguides are used to generate supercontinuum from 1280 nm to 2120 nm at the -30 dB level. The spectrum expands along the red …

Go to article

Computational Modelling For Phase Transformation Prediction In Super-Invar Alloys: Analytical And Experimental Data, Alexander S. Zhilin, Valeria R. Ramazanova, Joseph William Newkirk, Tarak A. Amine, Deborah Alvarenga Dec 2016

Computational Modelling For Phase Transformation Prediction In Super-Invar Alloys: Analytical And Experimental Data, Alexander S. Zhilin, Valeria R. Ramazanova, Joseph William Newkirk, Tarak A. Amine, Deborah Alvarenga

Materials Science and Engineering Faculty Research & Creative Works

The possibility of using computational modelling to predict phase transformation processes has been shown while examining super-invar samples. Due to the complicity of phase transformation processes in these alloys the correlation between modelling and experimental work has been described. Modelling allows basic background of composition behavior to be predicted but it doesn`t give the real structure components.

Go to article

Strain Phase Separation: Formation Of Ferroelastic Domain Structures, Fei Xue, Yongjun Li, Yijia Gu, Jinxing Zhang, Long-Qing Chen Dec 2016

Strain Phase Separation: Formation Of Ferroelastic Domain Structures, Fei Xue, Yongjun Li, Yijia Gu, Jinxing Zhang, Long-Qing Chen

Materials Science and Engineering Faculty Research & Creative Works

Phase decomposition is a well-known process leading to the formation of two-phase mixtures. Here we show that a strain imposed on a ferroelastic crystal promotes the formation of mixed phases and domains, i.e., strain phase separation with local strains determined by a common tangent construction on the free energy versus strain curves. It is demonstrated that a domain structure can be understood using the concepts of domain/phase rule, lever rule, and coherent and incoherent strain phase separation, in a complete analogy to phase decomposition. The proposed strain phase separation model is validated using phase-field simulations and experimental observations of PbTiO …

Go to article

Method For Fabricating Biocompatible Porous Titanium, B. Sonny Bal, Tieshu Huang, M. N. Rahaman Nov 2016

Method For Fabricating Biocompatible Porous Titanium, B. Sonny Bal, Tieshu Huang, M. N. Rahaman

Materials Science and Engineering Faculty Research & Creative Works

A method for fabricating porous metal constructs (such as porous Ti constructs) which may be used as implants in bone repair is disclosed. The method employs a new saltbath sintering process coupled with conventional powder metallurgy technology which is capable of fabricating porous metal constructs with controlled porosity and pore size having a lower production cost than conventional powder metallurgy methods.

Go to article

Water-Soluble Glass Substrate As A Platform For Biodegradable Solid-State Devices, Shihab Md Adnan, Kwangman Lee, Mohammad Tayeb Ahmad Ghasr, Matthew O'Keefe, D. E. Day, Chang-Soo Kim Nov 2016

Water-Soluble Glass Substrate As A Platform For Biodegradable Solid-State Devices, Shihab Md Adnan, Kwangman Lee, Mohammad Tayeb Ahmad Ghasr, Matthew O'Keefe, D. E. Day, Chang-Soo Kim

Materials Science and Engineering Faculty Research & Creative Works

A biodegradable glass material is utilized as a novel functional element of solid-state devices. A water-soluble borate glass substrate serves as the structural platform on which thin film device is built. The glass substrate completely dissolves in a saline solution in approximately 40 h. Intentional failure of the spiral device (RLC resonator circuit) as a result of rapid structural disintegration by dissolution is demonstrated in DC, AC, and RF ranges that agrees well with simulation. Adopting water-soluble glass elements is expected to be a viable approach to develop reliable all-inorganic biodegradable devices that are fully functional during an intended operational …

Go to article

Thermophysical Properties And Conduction Mechanisms In Asxse1-X Chalcogenide Glasses Ranging From X = 0.2 To 0.5, Jason Lonergan, Charmayne Smith (Lonergan), Devon Mcclane, Kathleen Richardson Oct 2016

Thermophysical Properties And Conduction Mechanisms In Asxse1-X Chalcogenide Glasses Ranging From X = 0.2 To 0.5, Jason Lonergan, Charmayne Smith (Lonergan), Devon Mcclane, Kathleen Richardson

Materials Science and Engineering Faculty Research & Creative Works

The arsenic (As) to selenium (Se) ratio in AsxSe1-x glasses ranging from x = 0.2 to 0.5 was varied in order to examine the effect of chemical and topological ordering on the glass' thermal transport behavior. The fundamental thermal properties of glass transition temperature (Tg), thermal conductivity (k), and heat capacity (cp) were experimentally measured using differential scanning calorimetry, transient plane source method, and ultrasonic testing. Based on topological constraint theory, inflections in Tg and k were found at the structural coordination number «r» of 2.4, whereas a slight increase in heat …

Go to article

Computational Fluid Dynamics Study Of Molten Steel Flow Patterns And Particle-Wall Interactions Inside A Slide-Gate Nozzle By A Hybrid Turbulent Model, Mahdi Mohammadi-Ghaleni, Mohsen Asle Zaeem, Jeffrey D. Smith, Ronald J. O'Malley Oct 2016

Computational Fluid Dynamics Study Of Molten Steel Flow Patterns And Particle-Wall Interactions Inside A Slide-Gate Nozzle By A Hybrid Turbulent Model, Mahdi Mohammadi-Ghaleni, Mohsen Asle Zaeem, Jeffrey D. Smith, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Melt flow patterns and turbulence inside a slide-gate throttled submerged entry nozzle (SEN) were studied using Detached–Eddy Simulation (DES) model, which is a combination of Reynolds–Averaged Navier–Stokes (RANS) and Large–Eddy Simulation (LES) models. The DES switching criterion between RANS and LES was investigated to closely reproduce the flow structures of low and high turbulence regions similar to RANS and LES simulations, respectively. The melt flow patterns inside the nozzle were determined by k–ε (a RANS model), LES, and DES turbulent models, and convergence studies were performed to ensure reliability of the results. Results showed that the DES model has significant …

Go to article

Protective Conversion Coating On Mixed-Metal Substrates And Methods Thereof, Matthew O'Keefe, Surender Maddela Sep 2016

Protective Conversion Coating On Mixed-Metal Substrates And Methods Thereof, Matthew O'Keefe, Surender Maddela

Materials Science and Engineering Faculty Research & Creative Works

Mixed-metal automotive vehicle bodies-in-white comprising ferrous metal surfaces, zinc surfaces, aluminum alloy surfaces, and magnesium alloy surfaces are cleaned and immersed in an aqueous bath comprising an adhesion promoter and an aqueous electrocoat bath (the adhesion promoter may be in the electrocoat bath. The adhesion promoter, which may be a cerium salt, is selected to react with each metal in the body surfaces to form an oxide layer that provides corrosion resistance for the surface and adherence for the deposited polymeric paint coating. The body is cathodic in the electrocoat deposition.

Go to article

Broad-Spectrum Antibacterial Characteristics Of Four Novel Borate-Based Bioactive Glasses, Megan Ottomeyer, Ali Mohammadkah, D. E. Day, David J. Westenberg Sep 2016

Broad-Spectrum Antibacterial Characteristics Of Four Novel Borate-Based Bioactive Glasses, Megan Ottomeyer, Ali Mohammadkah, D. E. Day, David J. Westenberg

Materials Science and Engineering Faculty Research & Creative Works

Bioactive glasses have been developed for medical applications in the body for bone and tissue repair and regeneration. We have developed a borate-containing bioactive glass (13-93B3, referred to as B3), which is undergoing clinical trials to assess its wound-healing properties. To complement the healing properties of B3, metal ion dopants have been added to enhance its antimicrobial properties. Bioactive glasses doped with silver, gallium or iodine ions were found to have broad spectrum antimicrobial effects on clinically relevant bacteria including MRSA. While the B3 glass alone was sufficient to produce antibacterial effects on select bacteria, adding dopants enhanced the broad-spectrum …

Go to article

First Prev Next Last