Materials Science and Engineering Commons^™

Multi-Physics Numerical Simulation Of Corrosion And Service Life Evaluation Of Novel Reinforced Concrete Systems, Jin Fan

Dissertations

Durability challenges of reinforced concrete materials can shorten the service life and increase the carbon footprint of civil infrastructure systems. Novel alternative materials, such as high-performance fiber reinforced cementitious composites (HPFRCCs) and recycled aggregate concrete (RAC), offer an alternative to tradi-tional concrete materials by increasing the service life of infrastructure or reducing raw material consumption, thereby reducing the life-cycle carbon footprint. Due, in part, to a lack of robust numerical tools, predicting the durability response of these emerging cementitious materials has been insufficiently addressed. A time-dependent multi-physics modeling framework is proposed and adopted to investigate the chloride induced deterioration mechanisms …

The Influence Of Diamine Curing Additives On The Network Architecture Of Phthalonitrile Thermosetting Polymers, Tyler J. Richardson

Dissertations

Phthalonitrile monomers undergo diamine-promoted polymerization by a complex reaction mechanism involving two competitive cure pathways, forming two primary network architectures: linear polyisoindoline chains and branched triazine crosslinks. The influence of the diamine curing additive on the polymerization pathway, and the influence of the resulting network architectures on cured network properties, have not been adequately explored within the phthalonitrile field. Two structurally different diamine curing additives, bis[4-(3-aminophenoxy)phenyl] sulfone (mBAPS) and 1,3-phenylenebis((4-(4-aminophenoxy)phenyl)methanone) (AEK-134), were studied for the polymerization of resorcinol phenylphosphate phthalonitrile (RPPhPN), where the influence of diamine structure and concentration on the polymerization behavior, network architecture, and bulk thermal and thermomechanical …

Advanced Materials For High Performance Lithium-Sulfur Batteries, Jian Yang

Dissertations

With the advantages of high capacity and low cost, lithium-sulfur batteries (LSBs) have been considered as one of the most promising candidates for next-generation batteries. However, the wide adoption of LSBs to the commercial markets is limited due to the fast capacity decay and low utilization of sulfur. To address these issues, advanced cathodes with high electronic conductivity and strong affinity to elemental sulfur and lithium polysulfides, which are intermediate products during the charge/discharge process, have been developed in this program. Carbon aerogels (RFCs) with controllable porous architectures have been fabricated through adjusting the process parameters and used as the …

Carrier Transport Engineering In Wide Bandgap Semiconductors For Photonic And Memory Device Applications, Ravi Teja Velpula

Dissertations

Wide bandgap (WBG) semiconductors play a crucial role in the current solid-state lighting technology. The AlGaN compound semiconductor is widely used for ultraviolet (UV) light-emitting diodes (LEDs), however, the efficiency of these LEDs is largely in a single-digit percentage range due to several factors. Until recently, AlInN alloy has been relatively unexplored, though it holds potential for light-emitters operating in the visible and UV regions. In this dissertation, the first axial AlInN core-shell nanowire UV LEDs operating in the UV-A and UV-B regions with an internal quantum efficiency (IQE) of 52% are demonstrated. Moreover, the light extraction efficiency of this …

Effect Of Current Density Ramping On The Anodic Reaction And Morphology Of Aerospace Aluminum Alloys, Peter Totaro Jr.

Dissertations

Aluminum anodizing has been experimented with and studied over the last century because of its ability to form uniform, well ordered cellular coatings on aluminum alloys. Anodizing aerospace alloys has been problematic, due to the alloying elements used to add strength and resistance to stress cracking corrosion. These intermetallic compounds, i.e., copper and zinc, promote oxygen evolution and stress as they accumulate in and on the surface of the forming aluminum oxide. These inclusions lead to increased electrical resistance that forms porous and flawed coating, which can lead to industrial and field failures. The amount of voltage placed on the …

The Fractionation Of Woody Biomass With Bifunctional Aryl Sulfonic Acids At Mild Conditions, Duo He

Dissertations

Fractionation of lignocellulose is a fundamental step in the valorization of cellulose, hemicelluloses, and lignin to produce various sustainable fuels, materials, and chemicals. Over the years, most fractionation processes are cellulose centered or lignin-first. However, regardless of the fractionation strategy, the previous reported fractionation processes either need high temperature and high pressure or intensive size reduction of lignocellulose prior to the process. Therefore, there is a need to develop low energy and rapid delignification with simplistic recovery of chemicals for advanced utilization of renewable and biodegradable lignocelluloses for the future biobased economy.

To address this need, an innovative and scalable …

Development Of Smart Wearable Sensory Systems On Flexible And Fabric Platforms For Health Monitoring Applications, Simin Masihi

Dissertations

Wearable sensing technology has recently received an increased attention in both research and commercialization phases and has moved from a vision of science fiction to reality with a wide variety of applications. This incredible growth can be attributed to several factors, such as affordability and ergonomics provided by advances in flexible electronics. The other factors that realized wearable sensing technology include a critical need for more accessible health care services experienced during the recent COVID pandemic, integration to the Internet of Things (IoT), and a growing consumer desire for health awareness. This dissertation presents the fulfillment of three main projects …

Analysis Of The Cyclic Behavior And Fatigue Damage Of Low Alloy Steels, Zahra Salemi Najafabadi

Dissertations

Fatigue is the most common type of failure in many structures and components subjected to cyclic loading. Surface effects in fatigued materials are of particular importance, since in most cases the surface is the preferred site of fatigue crack initiation. Microcracks originate at the metal surface due to stress concentration introduced by macro notches and micro defects in the surface layers. The microcrack initiation and propagation are controlled by the localized plastic deformation in the surface layers especially in the initial stage of fatigue failure process. Therefore, the knowledge regarding the cyclically induced changes in deformation resistance at the metal …

Nondestructive Evaluation Of 3d Printed, Extruded, And Natural Polymer Structures Using Terahertz Spectroscopy And Imaging, Alexander T. Clark

Dissertations

Terahertz (THz) spectroscopy and imaging are considered for the nondestructive evaluation (NDE) of various three-dimensional (3D) printed, extruded, and natural polymer structures. THz radiation is the prime candidate for many NDE challenges due to the added benefits of safety, increased contrast and depth resolution, and optical characteristic visualization when compared to other techniques. THz imaging, using a wide bandwidth pulse-based system, can evaluate the external and internal structure of most nonconductive and nonpolar materials without any permanent effects. NDE images can be created based on THz pulse attributes or a material’s spectroscopic characteristics such as refractive index, attenuation coefficient, or …

Effect Of Process Control Agents Used In Mechanochemical Synthesis On Properties Of The Prepared Composite Reactive Materials, Mehnaz Mursalat

Dissertations

The study explores synthesis and reactivity of new reactive materials prepared by ball milling. High-energy ball milling became a ubiquitous mechano-chemical tool to manufacture diverse powders, from pharmaceuticals or foods to alloys to new solid rocket propellants. It enabled a dramatic expansion of the range of chemical compositions obtainable; however, it did not so far, allowed one to fine-tune morphology or interfaces in the generated powders. It is shown in this work how different process control agents (PCAs) can serve to tune the powder morphology and reactivity. Commonly used as lubricants and cooling agents during milling, liquid PCAs can be …

The Impact Of Material And Environmental Properties On The Ettringite - Metaettringite Thermochemical Reaction, Aaron Strand

Dissertations

The use of energy is an essential need for people, with demand constantly increasing due to an increasing population and an increase in living and comfort standards. Since 1965, world energy consumption has quadrupled. During peak utilization, the strain on the grid infrastructure can be immense. As energy demand fluctuates during different times of the day and year, the energy production needs to scale accordingly This creates inefficiencies within the system such as over building generation capacity or losses from start up or ramping up production. This can be alleviated through load leveling where excess energy generated during low demand …

Optimization Of Polyhydroxyalkanoates (Phas) Bioplastic Production From Wastewater Activated Sludge, Bo Deng

Dissertations

Polyhydroxyalkanoate (PHA) is a biopolymer which has similar properties as fossil-fuel based plastic but also has capacity to biodegrade completely in the environment condition. This project aims to optimize the process to produce bioplastic PHA using activated sludge from wastewater. Specifically, five major research objectives are explored: (i) develop a quantification method of PHA by using Fourier-transform infrared spectroscopy (FTIR)F; (ii) improve the PHA production from mixed microbial cultures (MMC) by optimizing MMC; (iii) simulate the PHA production by using wastewater; (iv) evaluate the application of enzyme (alpha-amylase) in PHA production process; (v) market the investigation of wastewater produced PHA. …

Synthesis Of Polynitrogen With Radio Frequency Plasma, Haizheng Zhuang

Dissertations

Cubic gauche polynitrogen (cgPN) has been very attractive due to its high energy density that is 2.5 times higher than that of TNT. In the literature, cgPN has been investigated theoretically in detail, but few experimental works have been reported. In 2004, cgPN was first synthesized from nitrogen gas under extremely high temperature and high pressure (HTHP) conditions and the trace amount of cgPN in the high-pressure vessel decomposed once the pressure was released. Until recently, our group was the first to synthesize cgPN from NaN₃ precursor under ambient conditions with radio frequency (RF) plasma. In this study, the …

Copolymer Microphase Separation, Properties, And Applications, Daniel Weller

Dissertations

Copolymers represent a broad, but critically important class of materials. Often having properties superior to either of its constituents, copolymers are used in virtually all industries including automotive, aerospace, coatings, packaging, and cosmetics. Certain copolymers microphase separate to form nanosized domains that improve the physical properties of the copolymer. The polymer community already has a thorough understanding of how phase separation occurs, but the commercialization of phase separating copolymers lags significantly behind academia. Many of the copolymers that exist that have been undercharacterized and underutilized. This dissertation examines two such polymers. The first, a hard polystyrene material with soft nanodomains. …

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco

Dissertations

Organic semiconductors based on π-conjugated polymers show remarkable properties such as high tolerance to structural defects, low processing temperature requirements, biocompatibility, ease of fabrication, and tunable properties. Conjugated polymers integrated into device arrays can exhibit collective properties sensitive to minor perturbations in the surrounding media. However, these devices rely on serendipitous sensitivity to the analyte of interest, and strategies for specific detection remain a considerable change. There remains a compelling, global need for technologies to monitor phosphate due to its prevalence in agricultural runoff, leading to fish kills and economic decline for commercial and recreational fisheries. The strong hydration energies …

Characterization Of Disorder And Its Effects On Two-Dimensional Transition Metal Dichalcogenides, Krystal Rose York

Dissertations

Since the discovery of the unique electrical properties of graphene in 2004, there has been an increased interest in two-dimensional (2D) materials. However, graphene is known as a zero-gap semi-metal, thus spurring further research in order to find suitable 2D semiconductor materials. Transition metal dichalcogenides (TMDs) are a class of layered materials that have recently attracted attention. In particular, MoS2, MoSe2, WS2, and WSe2 have direct band gaps in their monolayer form and favorable electrical properties, making them promising materials for both electronic and optoelectronic applications. Like many 2D materials, studies in semiconductor TMD materials began with mechanically exfoliated sheets …

Thermomechanics Of Semiconducting Polymers And Their Morphological Phenomena, Luke Galuska

Dissertations

In contrast to conventional silicon-based electronics, semiconducting polymers show great promise for emerging applications in soft, flexible, and ductile electronic technologies. This is due to their polymeric nature, tailorable structure, and sub-100 nm device thickness. Despite this mechanical novelty, there remains a poor understanding of their structure-property-processing relationships, which has hindered growth within the field. This dissertation elucidates these relationships through investigation of their thermomechanics, and morphological phenomena. This was accomplished through the following projects:

1) To demonstrate the impact of backbone rigidity on semiconducting polymer thermomechanics, we varied the backbone rigidity of an NDI-based polymer by inserting flexible methylene …

Hydrophobically Modified Isosorbide Dimethacrylates As Biomaterials For Bisphenol A Free Dental Fillings, Bilal Marie

Dissertations

Amalgam and Bisphenol A glycerolate dimethacrylate (BisGMA) are the main dental filling materials in use today. Because of the negative perception of amalgam and its lower esthetic appeal, as well as the desire to replace the endocrine disruptor Bisphenol A, which is the building block of BisGMA, there has been a critical need to search for safer alternatives to these dental filling materials.

Isosorbide is a sugar-based molecule generally recognized as safe. It has been extensively studied as a replacement to the Bisphenol A core in various materials. However, isosorbide is extremely hygroscopic, and water uptake in dental fillings causes …

Electro-Chemo-Mechanics Of The Interfaces In 2d-3d Heterostructure Electrodes, Vidushi Sharma

Dissertations

Unique heterostructure electrodes comprising two-dimensional (2D) materials and bulk three dimensional (3D) high-performance active electrodes are recently synthesized and experimentally tested for their electrochemical performance in metal-ion batteries. Such electrodes exhibit long cycle life while they also retain high-capacity inherent to the active electrode. The role of 2D material is to provide a supportive mesh that allows buffer space for volume expansions upon ion intercalation in the active material and establishes a continuous electronic contact. Therefore, the binding strength between both materials is crucial for the success of such electrodes. Furthermore, battery cycles may bring about phase transformations in the …

Experimental And Computational Studies Of Functionalized Carbon Nanotubes For Use In Energy Storage Devices And Membranes, Emine S. Karaman

Dissertations

Electrolytes with good interfacial stability are a crucial component of any electrochemical device. The development of novel gel polymer electrolytes (GEs) with good interface stability and better manufacturability is important for the development of the next generation electrochemical devices. Gel electrolytes are hybrid electrolyte materials, combining benefits of both liquid and solid systems. Compared with liquid and solid electrolytes, GEs open new design opportunities and do not require rigorous encapsulation methods. In this dissertation, studies on functionalized carbon nanotubes (fCNTs) and graphene oxide (GO) doped polyvinyl alcohol (PVA) based gel electrolytes (GEs) are reported. The ionic conductivity and mechanical strength …

Electric-Field-Driven Processes In Multiphase Fluid Systems, Qian Lei

Dissertations

Advantages of using electric fields in miniaturized apparatuses for a wide range of applications are revealed by numerous experimental and theoretical studies over the last several decades as it offers a simple and efficient method for manipulation of multiphase fluid systems. This approach is considered to be especially beneficial for control of boiling processes and colloidal suspensions considered in the presented work.

Boiling. Today's trends for enhancing boiling heat transfer in terrestrial and space applications focus on removal of bubbles to prevent formation of a vapor layer over the surface at a high overheat. In contrast, this dissertation presents a …

Rheological Properties Of Recyclable Polymer Matrices For Advanced Composite Applications, Rahul Shankar

Dissertations

This dissertation focuses on evaluating the rheological characteristics of a variety of recyclable polymer matrices, which can compete with thermosets in a wide range of specialized applications. Studying the fundamental solid and melt-state viscoelastic properties and establishing structure-property-processing relationships is critical for the widespread adoption of these novel recyclable polymers in commercial applications. The first chapter provides an introductory overview of the different recyclable polymer matrices and their applications including high performance thermoplastics as thermoset replacements in high energy composite manufacture, multifunctional specialty thermoplastics for additive manufacturing and next generation, reprocessable covalent adaptable networks for self-healing applications. Furthermore, the important …

Impact Of Exposure On Thin Epoxy Overlay Performance, Abul Fazal Mazumder

Dissertations

Thin epoxy overlays are used for improving the condition and extending the service life of bridge decks. The tensile bond pull-off strength, evaluated as per the ASTM C1583, is used as the performance indicator. A failure in the substrate with a tensile strength of 250 psi or greater is considered acceptable. However, the performance evaluated on in-service bridge decks shows inconsistent results. Laboratory studies by several researchers documented a distinct performance difference when the overlays are exposed to room temperatures in comparison to elevated temperatures. However, the most influential parameters such as concrete surface profile, thermal compatibility between overlay and …

Feedstock Powders For Reactive Structural Materials, Daniel Hastings

Dissertations

Metals as fuels have higher energy density per unit mass or volume compared to any hydrocarbon. At the same time, metals are common structural materials. Exploring metals as reactive structural materials may combine their high energy density with attractive mechanical properties. Preparing such materials, however, is challenging. Requirements that need to be met for applications include density, strength, and stability enabling the component to sustain the structure during its desired operation; added requirements are the amount and rate of the energy release upon impact or shock. Powder technology and additive manufacturing are approaches considered for design of reactive structural materials. …

Towards Quality By Design (Qbd) Of Pharmaceutical Oral Films Loaded With Poorly Watersoluble Drugs, Eylul Cetindag

Dissertations

Oral films are an emerging drug delivery dosage form with numerous advantages such as ease of handling, the possibility to circumvent the first-pass metabolism, better patient compliance, capability for continuous manufacturing, and as a platform for personalized medicine. As films are different from other final dosages by their dimensions and their matrix form, further research is required to better understand the impact of excipient and drug on product performance to assure a consistent and good quality product. Therefore, this dissertation aims to contribute towards the processability and manufacturability of films by examining the impact of the materials and processes. First, …

Development And Characterization Of Composite Membranes For Use In Countercurrent Solvent Extraction, Lydia Neves Rodrigues

Dissertations

Porous membranes having a particular wetting characteristic, hydrophobic or hydrophilic, are used for nondispersive membrane solvent extraction (MSX) where two immiscible phases flow on two sides of the membrane. The aqueous-organic phase interface across which solvent extraction/back extraction occurs remains immobilized on one surface of the membrane. This process requires the pressure of the phase not present in membrane pores to be either equal to or higher than that of the phase present in membrane pores; the excess phase pressure should not exceed a breakthrough pressure. In countercurrent MSX with significant flow pressure drop in each phase, this often poses …

First-Principles Density Functional Theory Studies On Perovskite Materials, Aneer Lamichhane

Dissertations

Perovskites are a family of materials with a diverse combination of different elements. As a consequence, they exhibit numerous functionalities such as pyroelectric, piezoelectric, ferroelectric, and ferromagnetic with applications in photovoltaic cells, LEDs, superconductivity, colossal magneto-resistance, and topological insulators. After 2009, perovskites have gained notoriety as suitable materials for solar cells and alternative candidates to silicon-based conventional solar cells. Generally, oxide perovskites exhibit good dielectric properties, halide perovskites display good photonic qualities, and chalcogenide perovskites are used in applications in solid-state lighting, sensing, and energy harvesting. In this dissertation, various types of perovskites ranging from oxide to halide are investigated …

Fluorine-Based Inorganic Oxidizers For Use In Metal-Based Reactive Materials, Siva Kumar Valluri

Dissertations

This work explores inorganic fluorides as oxidizers for fuel-rich reactive materials. A preliminary assessment of metal fluorides accounting for their enthalpy of formation points to bismuth (III) fluoride, BiF3 and cobalt (II) fluoride, CoF2 as oxidizers of interest. Initially, composite powders of aluminum with chosen fluorides at 50-50 wt. % are prepared by arrested reactive milling. Despite an increase in reactivity and lowtemperature ignition, the prepared composite powders are insensitive to initiation by electro-static discharge (ESD), making them attractive alternative to analogous thermites having very high ESD sensitivity. In air, the composite powder particles burn faster than reference aluminum particles …

Controlled Reduction Of Graphene Oxide And Graphene Oxide-Carbon Nanotube Hybrids And Their Applications, Samar Azizighannad

Dissertations

Graphene and graphene derivatives are widely used in diverse research and industrial applications. Graphene production on a large scale is carried out by exfoliating graphite oxide and producing graphene oxide (GO), which comprises of graphene sheets with different oxygen-containing functional groups such as hydroxyl, carboxyl, and carbonyl. GO is reduced to reduced graphene oxide (rGO), which has properties that are closer to graphene. Properties of GO and rGO depend upon the oxygen content, and the effect of reducing oxygen content on the aqueous behavior of rGOs is not well understood.

In an effort to understand how properties of rGO change …

Atomic Oxygen Resistant Low Earth Orbit Stable Polymer Matrix Composites Employing Phenylphosphine Oxide Epoxy-Amines, Witold Fuchs

Dissertations

Atomic oxygen (AO) attacks polymer matrix composites (PMC’s) on the surfaces of spacecraft in low earth orbit (LEO) and threatens safe spacecraft operation and service life. Incorporating phenylphosphine oxide (PPO) groups into polymer chains offers a self-regenerating method of protection from AO but remains poorly understood. Herein, epoxies containing PPO groups were synthesized with increasing concentrations of phosphorus [P] from 0 to 8 wt % to investigate their AO resistance. Measurements confirmed the exposure of these materials to AO produces a passivation phosphate (POx) layer on the surface of the sample and the efficacy of the resultant layer was directly …