Materials Science and Engineering Commons^™

Assessing Porosity Limit In Freeze-Cast Sintered Lithium Titanate (Li₄Ti₅O₁₂) Materials, Rohan Parai, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

This study aims to assess the lower limit of porosity that can be achieved in freeze-cast sintered lithium titanate (LTO) materials while maintaining the characteristic pore directionality. LTO materials were fabricated with solid loading varying in the range of 30–37 vol.%. Sucrose and cationic dispersant were used to vary viscosity and total solute concentration in the aqueous LTO suspensions. Two series of suspension compositions were selected for freeze-casting. In one series, aqueous suspensions were prepared by mixing deionized (DI) water, sucrose, and LTO powder, while in the other series, aqueous suspensions were prepared by mixing DI water, sucrose, cationic dispersant …

Morphing Shape Metastructures Using The Hybrid Position Feedback Control And Bistable Structural Elements, Mehmet Simsek, Thomas E. Alberts, Onur Bilgen

Mechanical & Aerospace Engineering Faculty Publications

This research introduces a new multi-degree-of-freedom metastructure concept utilizing a hybrid position feedback controller. An arbitrary number of bistable segments, or structural elements, are connected serially or in parallel to form a distributed bistable structure, or a so-called metastructure. The hybrid controller, an unstable-then-stable second-order single-degree-of-freedom system, leverages the resonant mode of a bistable system to destabilize it and dynamically induce snap-through between equilibria. The metastructure inherits multiple bistable positions, maintaining equilibrium shapes without consuming power and enabling many equilibrium configurations. Two geometric configurations are proposed and analyzed using a modified hybrid feedback control approach, which rejects forces from neighboring …

Side-By-Side Evaluation Of The Outgassing Rate And Ultimate Pressure Achieved Inside Tubes Made Of Low-Carbon And Stainless Steel, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

The hydrogen outgassing rate of a vacuum chamber made of AISI 1020 low-carbon steel was found to be notably smaller than a similar chamber made of AISI 316L stainless steel following heat treatment at 150 degrees C. When the chambers were baked at 400 degrees C, the outgassing rate of the 1020 low-carbon steel chamber was approximately 2000 times smaller than that of the 316L stainless-steel chamber. After quantifying hydrogen outgassing rates, vacuum chambers made of 1020 low-carbon steel and 316L stainless steel were heated for a prescribed duration and then pumped with an ion pump and nonevaporable getter pump …

Polymorphism And Mechanical Behavior In Hot-Pressed 3d-Printed Polyamide Composite: Effects Of Pressure And Temperature, John Barber, Patricia Revolinsky, Jimesh Bhagatji, Diego Pedrazzoli, Sergii Kravchenko, Oleksandr Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

The aim of this work is to study the effect of high-temperature compaction (HTC) upon the polymorphism and the mechanical behavior of an additively manufactured (AM) carbon fiber-reinforced polyamide (PA6). Different pressure and temperature levels during HTC were tested to determine the overall effect on the mechanical behavior and material crystalline composition. Treated, carbon fiber-reinforced PA6 samples were analyzed using differential scanning calorimetry, X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and three-point bending testing. When considered with respect to as-printed samples, an HTC temperature of 190 °C combined with 80 psi pressure resulted in an increased flexural modulus and strength …

Optimizing Material Selection And Operational Conditions For Xhv Systems: Lessons From Aisi 1020 And 316l Comparative Studies, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

In this study, AISI 1020 low-carbon steel was investigated as a cost-effective alternative to SS316L stainless steel for reaching extreme high vacuum (XHV) conditions. After being baked at 400°C, a vacuum chamber made of low-carbon steel material exhibited an outgassing rate approximately 2000 times smaller than a similar chamber made of stainless steel. Its activation energy for hydrogen diffusion (27 kJ/mol) is less than half that of stainless steel (60.3 kJ/mol), indicating more efficient hydrogen removal during bakeout. MolFlow+ simulations supported the experimental data and demonstrated the importance of system geometry optimization and minimizing stainless steel content for achieving optimal …

Rheology Of Alumina Suspensions Subjected To Alternating Current Electric Fields For Freeze-Casting, Sivakumar Chithamallu, Ruksana Baby, Jacob L. Jones, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Alternating current (AC) electric field can extrinsically tune freeze‐cast microstructure, originating from field‐induced increase in viscosity of ceramic suspensions. However, the changes that occur in a ceramic suspension and rheological behavior, ultimately affecting freeze‐cast microstructure, are not well understood. Moreover, the effects of AC electrokinetic forces and temperature on viscosity need to be decoupled. The viscosity and temperature of ceramic suspensions subjected to AC field and direct heating were measured, revealing that the increase in viscosity is due to AC dielectrophoretic forces rather than field‐induced heating of suspension. The shear thinning behavior of suspensions characterized using a power‐law model reveals …

Mitigating Out-Of-Plane Fiber Waviness In Afp Laminates With Tow-Gaps Via Selective Placement Of Thermoplastic Veils, Ahmadreza Ravangard, Kuthan Celebi, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Fiber tow-gaps and overlaps formed during the Automated Fiber Placement (AFP) process pose a significant challenge by introducing non-uniform composite morphologies, often characterized by resin-rich regions and fiber waviness. These defects occur as deposited fibers sink into the gap regions during consolidation, with gap geometry determined during path planning. Such morphological inconsistencies can compromise structural reliability by initiating premature failure, particularly through localized out-of-plane waviness and resin accumulation. This study investigates the integration of high melting temperature thermoplastic veils, specifically polyetherimide (PEI), into fiber tow-gaps as a method to prevent ply sinking and reduce fiber waviness on both internal and …

A Comprehensive Review Of Piezoelectric Pvdf Polymer Fabrications And Characteristics, Nadia Ahbab, Sidra Naz, Tian-Bing Xu, Shihai Zhang

Mechanical & Aerospace Engineering Faculty Publications

Polyvinylidene fluoride (PVDF) polymer films, renowned for their exceptional piezoelectric, pyroelectric, and ferroelectric properties, offer a versatile platform for the development of cutting-edge micro-scale functional devices, enabling innovative applications ranging from energy harvesting and sensing to medical diagnostics and actuation. This paper presents an in-depth review of the material properties, fabrication methodologies, and characterization of PVDF films. Initially, a comprehensive description of the physical, mechanical, chemical, thermal, electrical, and electromechanical properties is provided. The unique combination of piezoelectric, pyroelectric, and ferroelectric properties, coupled with its excellent chemical resistance and mechanical strength, makes PVDF a highly valuable material for a wide …

Outgassing Measurements Of Bare And Magnetite-Coated Low-Carbon Steel Vacuum Chambers, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

The outgassing properties of bare and magnetite-coated AISI 1020 low-carbon steel vacuum chambers were evaluated to establish material selection criteria for extreme high vacuum applications, namely, to explore the possibility of using these materials to build next-generation spin-polarized photoelectron guns. Water outgassing measurements using the throughput method revealed that the magnetite-coated chamber exhibited five times lower outgassing at room temperature prior to baking, but this advantage disappears after 80 °C baking. Hydrogen outgassing measurements demonstrated significant differences after intensive heat treatment: the bare low-carbon steel vacuum chamber achieved a specific outgassing rate of 9.6 × 10⁻¹⁶ Torr L s …

Solid Loading Effects On The Assembly Of Alumina Particles In Aqueous Suspensions Due To The Dielectrophoretic Forces, Sivakumar Chithamallu, Rohan Kiran Parai, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Current work in situ investigated the mechanisms of the interparticle interactions that evolve in dilute aqueous alumina suspensions subjected to alternating current (AC) electric field and the effects of solid loading of suspensions. The interactions were investigated for alumina suspension compositions in the 0.005‒0.04 vol.% solid loading range. Field‐induced interactions evolved via particle motion and dynamic assembly, chain formation parallel to the direction of the applied field and chain growth, chain cross‐linking, and chain thickening. The evolution time of each of those events was rapidly accelerated with solid loading. While chain cross‐linking was negligible in low solid loading suspensions, a …

Multifunctional Nanoscale Pigments: Emerging Risks And Circular Strategies For A Sustainable Future, Ajay Vikram Singh, Preeti Bhardwaj, Vimal Kishore, Sunil Choudhary, Akihiko Hirose, Neha Gupta, Madleen Busse, Swarn Lata Singh, Christopher J. Osgood

Biological Sciences Faculty Publications

The substantial penetration of nanoscale pigments into a range of sectors has changed the dynamics of industries such as medical, material science, and many more. Nonetheless, their persistence in the environment and probable adverse impacts on health require that an assessment of such risks be formulated considering the One Health perspective. This viewpoint considers the crossing of boundaries of progress in the nanotechnology of nanoscale pigments with environmental, animal, and human health and emphasizes the significance of collaborative activity. Traditional perspectives explain the distribution of pigment history, while the nanotechnology of today's accessibility poses problems regarding utilization, toxicities, and interactions …

A Comparison Of Microcrystal Electron Diffraction And X-Ray Powder Diffraction For The Structural Analysis Of Metal-Organic Frameworks, Erik Biehler, Silvana Pagola, Daniel Stam, Johannes Merkelbach, Christian Jandl, Tarek M. Abdel-Fattah

Chemistry & Biochemistry Faculty Publications

This study successfully implemented microcrystal electron diffraction (microED) and X-ray powder diffraction (XRPD) for the crystal structure determination of a new phase, TAF-CNU-1, Ni(C₈H₄O₄)·3H₂O, solved by microED from single microcrystals in the powder and refined at the kinematic and dynamic electron diffraction theory levels. This nickel metal–organic framework (MOF), together with its cobalt and manganese analogues with formula M (C₈H₄O₄)·2H₂O with M = Mn ^II or Co^II, were synthesized in aqueous media as one-pot preparations from the corresponding hydrated metal chlorides and sodium terephthalate, as a promising `green' synthetic route to moisture-stable MOFs. The crystal structures of the …

Metathesis Or Isomerization: Counteranion Directed Reactivity Of Grubbs I, Paul D. Miller, Joe B. Calkins, Craig A. Bayse, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Catalytic isomerization of alkenes has garnered interest for many years, but there are remaining challenges when it comes to thermodynamic selectivity and uncontrolled isomerization. Nonbiased substrates, be it sterically or thermodynamically, remain challenging for many catalysts, with a few examples available in the more modern literature. Herein, we present the controlled isomerization of linear alkenes with a cocatalytic mixture of commercially available catalyst and reagents: Grubbs I, tris(pentafluorophenyl)borane, and triethylsilane. DFT calculations indicate that an observed alkylidyne hydride intermediate is in rapid equilibrium with an alkylidene that binds the alkene substrate. This combination results in a pi-acidic metal and a …

Amphiphilic Tripodal Metalloligands: Synthesis, Coordination Chemistry And Preliminary Catalysis, Austin W. Medley, Paul D. Miller, Craig A. Bayse, Robert D. Pike, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Triscatecholate binding has been widely studied in the context of biological systems, supramolecular chemistry, and weak aggregate interactions. However, the utilization of the triscatecholate binding motif for the preparation of metalloligands remains unexplored. Herein, we report the synthesis, structural characterization, and functional studies of a triscatecholate ligand with an appended pyridyl residue as a candidate for such applications. Our findings reveal that the selective formation of cis-triscatecholate-based metalloligands is influenced by electronic effects on the catecholate anions, enabling the targeted synthesis of Al(III), Ga(III), and In(III) triscatecholate metalloligands capable of binding Zn(II) and Ru(II) at the appended pyridyl moiety for …

Optimizing Superconducting Nb Film Cavities By Mitigating Medium-Field Q-Slope Through Annealing, B. Abdisatarov, G. Eremeev, H. E. Elsayed-Ali, D. Bafia, A. Murthy, Z. Sung, A. Netepenko, A. Romanenko, C. P.A. Carlos, G. J. Rosaz, S. Calatroni, S. Leith, A. Grassellino

Electrical & Computer Engineering Faculty Publications

Niobium films are of interest in applications in various superconducting devices, such as superconducting radiofrequency cavities for particle accelerators and superconducting qubits for quantum computing. In this study, we address the persistent medium-field Q-slope issue in Nb film cavities, which, despite their high-quality factor at low RF fields, exhibit a significant Q-slope at medium RF fields compared to bulk Nb cavities. Traditional heat treatments, effective in reducing surface resistance and mitigating the Q-slope in bulk Nb cavities, are challenging for Nb-coated copper cavities. To overcome this challenge, we employed DC bias high-power impulse magnetron sputtering to deposit …

Mxenes In Biosensing: Enhancing Sensitivity And Flexibility - A Review Of Properties, Applications, And Future Directions, Ali Mohammad Amani, Lobat Tayebi, Ehsan Vafa, Alireza Jahanbin, Milad Abbasi, Ahmed Vaez, Hesam Kamyab, Lalitha Gnanasekaran, Shreeshivadasan Chelliapan

Electrical & Computer Engineering Faculty Publications

MXenes are a novel type of nanostructured material that has received a lot of attention for their potential applications in bioanalysis owing to their unique features. These materials, made from transition metal nitrides, carbides, or carbonitrides, have a number of advantages, including high hydrophilicity, a large surface area, strong metallic conductivity, superior ion transport capabilities, biocompatibility, and low diffusion barriers. Their surfaces are easily manipulated, making them more adaptable for a variety of applications, including biosensing. The outstanding properties of MXenes have attracted researchers of different fields, including renewable energy, fuel cells, supercapacitors, electronics, and catalysis. In the context of …

A Fast Framework For Generating Radioactive Mixture Spectra And Its Application To Remote High-Performance Mixture Identification, Chiman Kwan, Bulent Ayhan, Adam Stavola, Kazi Aminul Islam, Hongfang Zhang, Jiang Li

Electrical & Computer Engineering Faculty Publications

Remote detection of radioactive materials in mixtures using handheld or portal detectors remains a challenge because of factors such as low concentration, environmental interference, sensor noise, and other complications. This work introduces a fast framework for generating realistic mixture spectra. Moreover, we present mixture isotope identification using data generated by the fast framework. Researchers have examined a range of conventional and recent algorithms within the fields of machine learning and deep learning. An application to uranium enrichment-level prediction has been included. Extensive simulation experiments validated the efficacy of the proposed framework.

Pla Polymer Binder In Core Production - Influence On Final Casting Dimensions, Artur Soroczyński, Krzysztof Rechowicz

Virginia Digital Maritime Center (VDMC) Faculty Publications

The foundry industry is seeking an ecological alternative to synthetic molding resins. This study evaluates the technological properties of core sands bonded with biodegradable polylactide (PLA). Cores prepared on a 2% quartz sand matrix were subjected to casting processes using two alloys with extremely different pouring temperatures: gray cast iron (approx. 1200 °C) and AK11 silumin (approx. 710 °C). The research methodology included macroscopic assessment, dimensional analysis using 3D scanning (GOM Inspect), and qualitative knock-out assessment supported by numerical temperature field simulation. The results showed that the high crystallization temperature of cast iron leads to complete thermal degradation of the …

Evaluating The Effectiveness Of Stay-In-Place Forms To Improve The Tosional Stability Of Box Beam Bridges During Erection, Karl E. Barth, Michael W. Seek, Gregory K. Michaelson, Dimitra Pyrialakou, Brook T. Woldegabriel

Engineering Technology Faculty Publications

Cold-formed tub girders provide an effective steel solution for short-span bridges. The girders are often delivered with an open top with stay-in-place forms installed on site. Walkways may be installed to the side of the girder that can induce significant torsion rotations in the open cross section. Full scale tests on girder specimens have shown that installing one or two panels of stay in place forms at the ends of the girder can significantly reduce the torsion rotation of the girder by providing warping resistance. Cantilever tests on the stay in place forms are performed to investigate the influence of …

Electrochemical And Nanomaterial Based Strategies For Nonenzymatic Glucose Detection: A Review, Reagan Aviha, Gymama Slaughter

Center for Bioelectronics Publications

Electrochemical glucose sensing technologies have undergone significant evolution, with continual advancements aimed at improving sensitivity, selectivity, and user convenience. This review systematically explores the development of emerging nonenzymatic glucose sensor designs. Nonenzymatic sensors are critically evaluated for their ability to overcome enzymatic limitations, leveraging novel materials and catalytic mechanisms. Additionally, the emergence of smartphone-integrated glucose monitoring systems is highlighted as the fifth generation, representing a paradigm shift toward personalized, real-time healthcare management. Emphasis is placed on the strategies employed to reduce the working electrode potential and enhance analytical performance. Key analytical metrics and real-sample applicability are evaluated, and persistent challenges …

Effect Of Bioactive Glass On Pxdda / Pxdda-Co-Pla Nanocomposite For Hard Tissue Reconstruction: Synthesis And Characterization, Ehsan Vafa, Lobat Tayebi, Fatemeh Azizli, Somayeh Parham, Katayoon Rezaeeparto, Sedigheh Azadi, Ali Mohammad Amani, Mohammad Javad Azizli, Hesam Kamyab, Shreeshivadasan Chelliapan, Saravanan Rajendran

Electrical & Computer Engineering Faculty Publications

Newer bone graft materials face various challenges in achieving optimal mechanical strength, bioactivity, and antibacterial action simultaneously, which can result in suboptimal regeneration outcomes and increased infection risks In the present study, we developed a novel nanocomposite of poly (xylitol-co-dodecanedioic acid) (PXDDA) and poly (lactic acid) (PLA) with 1-10 wt% incorporation of bioactive glass (BG), utilizing a a PXDDAco-PLA compatibilizer for maintaining homogeneity. Extensive characterization techniques including, Fourier infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauere Emmette Teller (BET), Proton Nuclear Magnetic Resonance (¹H NMR) and contact angle measurements, revealed that the addition …

The Impact Of Chromium Ion Implantation On Ald Lead Chalcogenide Thin Films, Haifeng Cong, Charlotte Poterie, Jean Francois Barbot, Helmut Baumgart

Electrical & Computer Engineering Faculty Publications

Inherently the synthesis of semiconducting materials by Atomic Layer Deposition ALD produces only intrinsic undoped films which require the introduction of small amounts of impurities for doping to change them into extrinsic semiconductors. Apart from various in-situ diffusion doping techniques like delta doping during the ALD process, post deposition doping by ion implantation affords the best control of dose and doping profile. The present study investigates the impact of 180 keV Cr⁺ ion implantation on the properties of semiconducting ALD lead chalcogenide thin films to improve their thermoelectric figure of merit. The implantation was accomplished with 180 keV Chromium …

Potential Of Lidar And Hyperspectral Sensing For Overcoming Challenges In Current Maritime Ballast Tank Corrosion Inspection, Sergio Pallas Enguita, Jiajun Jiang, Chung-Hao Chen, Samuel Kovacic, Richard Lebel

Electrical & Computer Engineering Faculty Publications

Corrosion in maritime ballast tanks is a major driver of maintenance costs and operational risks for maritime assets. Inspections are hampered by complex geometries, hazardous conditions, and the limitations of conventional methods, particularly visual assessment, which struggles with subjectivity, accessibility, and early detection, especially under coatings. This paper critically examines these challenges and explores the potential of Light Detection and Ranging (LiDAR) and Hyperspectral Imaging (HSI) to form the basis of improved inspection approaches. We discuss LiDAR’s utility for accurate 3D mapping and providing a spatial framework and HSI’s potential for objective material identification and surface characterization based on spectral …

Quantifying Trapped Magnetic Vortex Losses In Niobium Resonators At Mk Temperatures, D. Bafia, B. Abdisatarov, R. Pilipenko, Y. Lu, G. Eremeev, A. Romanenko, A. Grassellino

Electrical & Computer Engineering Faculty Publications

Trapped magnetic vortices in niobium introduce microwave losses that degrade the performance of superconducting resonators. While such losses have been extensively studied above 1 K, we report here their direct quantification in the millikelvin and low-photon regime relevant to quantum devices. Using a high-quality factor 3D niobium cavity cooled through its superconducting transition in controlled magnetic fields, we isolate vortex-induced losses and find the resistive component of the sensitivity to trapped flux S to be approximately 2 n Ω/mG at 10 mK and 6 GHz. The decay rate is initially dominated by two-level system (TLS) losses from the native niobium …

Mxene-Based Materials For Enhanced Water Quality: Advances In Remediation Strategies, Ali Mohammad Amani, Milad Abbasi, Atena Najdian, Farzaneh Mohamadpour, Seyed Reza Kasaee, Hesam Kamyab, Shreeshivadasan Chelliapan, Mostafa Shafiee, Lobat Tayebi, Ahmad Vaez, Atefeh Najafian, Ehsan Vafa, Sareh Mosleh-Shirazi

Electrical & Computer Engineering Faculty Publications

Two-dimensional MXenes are promising candidates for water treatment because of their large surface area (e.g., exceeding 1000 m²/g for certain structures), high electrical conductivity (e.g., >1000 S/m), hydrophilicity, and chemical stability. Their strong sorption selectivity and effective reduction capacity, exemplified by heavy metal adsorption efficiencies exceeding 95 % in several studies, coupled with facile surface modification, make them suitable for removing diverse contaminants. Applications include the removal of heavy metals (e.g., achieving >90 % removal of Pb(II)), dye removal (e.g., demonstrating >80 % removal of methylene blue), and radioactive waste elimination. Furthermore, 3D MXene architecture exhibit enhanced performance in antibacterial …

Preparation Of Mocvd-Grown Photocathodes Containing A Strained Gaas/Gaasp Superlattice, G. Blume, A. Masters, J. Grames, M. Stutzman, M. Grau, S. Marsillac

Physics Faculty Publications

In this work, we investigate heat cleaning options for high-polarization GaAs/GaAsP strained-superlattice (SSL) photocathodes with a distributed Bragg reflector (DBR) that were grown using metalorganic chemical vapor deposition (MOCVD). This was done using a microMott polarimeter at Jefferson Lab to optimize both quantum efficiency and polarization. The fabrication process for MOCVD-grown photocathodes does not allow for the inclusion of an arsenic cap, contrary to what is done when fabricating photocathodes using molecular-beam epitaxy (MBE). Without proper preparation, the performance of MOCVD-grown photocathodes can be limited due to surface contamination. Here, we varied both duration and temperature of the heat cleaning …

Investigation Of New Superconducting Materials For The Next Generation High-Performance Rf Superconducting Cavities For Particle Accelerators, Alex Gurevich, Jean Delayen, Chang-Beom Eom, Gianluigi Ciovati

Physics Faculty Publications

In this DOE-funded project DE-SC0010081-020 Old Dominion University (ODU) in collaboration with University of Wisconsin (UW) and Jefferson Laboratory have investigated both experimentally and theoretically electromagnetic response and losses in multilayered superconducting structures made of new SRF materials which can push the field and Q performance limits of accelerating cavities.

Intrinsic Manipulation Of Microstructure And Strength Of Ice-Templated Lithium Titanate, Rohan Parai

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation focuses on developing a fabrication landscape first time ever for directionally porous lithium titanate (LTO) materials using ice-templating technique. Ice-templating, a promising fabrication technique for porous ceramics, enables the formation of sintered structures with anisotropic pores that are aligned to improve mechanical stability of materials.

The work presented in this dissertation addresses advancements in tuning the porosity, strength, and microstructural characteristics of ice-templated LTO materials through adjustments of intrinsic variables, including sucrose as a water-soluble additive, variations in freezing front velocity, solute concentration, and solid loading. First, this study demonstrated that adding sucrose in LTO suspensions increased the …

Mesostructure Reconstruction Of Prepreg Platelet Molded Composite With Artificial Intelligence, Richard Larson

Mechanical & Aerospace Engineering Theses & Dissertations

Prepreg platelet molded composites (PPMC) are long, discontinuous fiber reinforced polymer materials. PPMC are an important subcategory of composite materials as they are processible into geometrically complex structures and can be produced via high-throughput manufacturing processes, however they have higher stiffness and strength as compared to traditional discontinuous fiber reinforced polymers. However, there is inherent randomness in the structure of PPMCs and as such, PPMC parts frequently require per part testing that is cost prohibitive.

Herein, a method using artificial intelligence is proposed as a more cost-effective method of inspecting PPMC parts. Different artificial intelligence (AI) architectures are explored to …

Alternative Applications Of Composite Materials To Reduce Radar Cross Section, Mark Patterson

Mechanical & Aerospace Engineering Theses & Dissertations

The use of carbon nanoparticles and graphene in composite materials has created a foundational shift in enhancing performance across mechanical, thermal, and electrical properties. Such applications are vital in the aerospace industry. However, there has not been such a focus on the material use for reducing radar cross section (RCS). Historically, RCS is minimized by designing sharp geometric shapes to deflect or dissipate the incoming electromagnetic waves away from the receiving antenna. However, these designs are not always optimized for aerodynamics. The goal of this research is to understand the application of composite materials and specifically carbon nanotubes (CNTs) to …