Materials Science and Engineering Commons^™

Experimental And Computational Studies Of Functionalized Carbon Nanotubes For Use In Energy Storage Devices And Membranes, Emine S. Karaman

Dissertations

Electrolytes with good interfacial stability are a crucial component of any electrochemical device. The development of novel gel polymer electrolytes (GEs) with good interface stability and better manufacturability is important for the development of the next generation electrochemical devices. Gel electrolytes are hybrid electrolyte materials, combining benefits of both liquid and solid systems. Compared with liquid and solid electrolytes, GEs open new design opportunities and do not require rigorous encapsulation methods. In this dissertation, studies on functionalized carbon nanotubes (fCNTs) and graphene oxide (GO) doped polyvinyl alcohol (PVA) based gel electrolytes (GEs) are reported. The ionic conductivity and mechanical strength …

Electric-Field-Driven Processes In Multiphase Fluid Systems, Qian Lei

Dissertations

Advantages of using electric fields in miniaturized apparatuses for a wide range of applications are revealed by numerous experimental and theoretical studies over the last several decades as it offers a simple and efficient method for manipulation of multiphase fluid systems. This approach is considered to be especially beneficial for control of boiling processes and colloidal suspensions considered in the presented work.

Boiling. Today's trends for enhancing boiling heat transfer in terrestrial and space applications focus on removal of bubbles to prevent formation of a vapor layer over the surface at a high overheat. In contrast, this dissertation presents a …

Flexible Microfluidic Device With Nonplanar Interdigitated Microelectrodes, Saud Alssaidy

Theses

The lab-on-a-chip concept has improved significantly in recent years to meet global demand for various applications with the advent of new technologies. Much progress has been achieved, but many microfluidic devices still suffer from design limitations in terms of sensitivity and selectivity because they use rigid, fragile substrate materials and conventional electrodes, which do not provide high sensitivity or selectivity and suffer from signal-to-noise ratio issues. This work proposes a novel device architecture that uses flexible, transparent top and bottom layers integrated with (nonplanar interdigitated microelectrodes) to create a sandwich-like flexible substrate base. The top and bottom layers consist of …

Feedstock Powders For Reactive Structural Materials, Daniel Hastings

Dissertations

Metals as fuels have higher energy density per unit mass or volume compared to any hydrocarbon. At the same time, metals are common structural materials. Exploring metals as reactive structural materials may combine their high energy density with attractive mechanical properties. Preparing such materials, however, is challenging. Requirements that need to be met for applications include density, strength, and stability enabling the component to sustain the structure during its desired operation; added requirements are the amount and rate of the energy release upon impact or shock. Powder technology and additive manufacturing are approaches considered for design of reactive structural materials. …

Towards Quality By Design (Qbd) Of Pharmaceutical Oral Films Loaded With Poorly Watersoluble Drugs, Eylul Cetindag

Dissertations

Oral films are an emerging drug delivery dosage form with numerous advantages such as ease of handling, the possibility to circumvent the first-pass metabolism, better patient compliance, capability for continuous manufacturing, and as a platform for personalized medicine. As films are different from other final dosages by their dimensions and their matrix form, further research is required to better understand the impact of excipient and drug on product performance to assure a consistent and good quality product. Therefore, this dissertation aims to contribute towards the processability and manufacturability of films by examining the impact of the materials and processes. First, …

First-Principles Density Functional Theory Studies On Perovskite Materials, Aneer Lamichhane

Dissertations

Perovskites are a family of materials with a diverse combination of different elements. As a consequence, they exhibit numerous functionalities such as pyroelectric, piezoelectric, ferroelectric, and ferromagnetic with applications in photovoltaic cells, LEDs, superconductivity, colossal magneto-resistance, and topological insulators. After 2009, perovskites have gained notoriety as suitable materials for solar cells and alternative candidates to silicon-based conventional solar cells. Generally, oxide perovskites exhibit good dielectric properties, halide perovskites display good photonic qualities, and chalcogenide perovskites are used in applications in solid-state lighting, sensing, and energy harvesting. In this dissertation, various types of perovskites ranging from oxide to halide are investigated …

Fluorine-Based Inorganic Oxidizers For Use In Metal-Based Reactive Materials, Siva Kumar Valluri

Dissertations

This work explores inorganic fluorides as oxidizers for fuel-rich reactive materials. A preliminary assessment of metal fluorides accounting for their enthalpy of formation points to bismuth (III) fluoride, BiF3 and cobalt (II) fluoride, CoF2 as oxidizers of interest. Initially, composite powders of aluminum with chosen fluorides at 50-50 wt. % are prepared by arrested reactive milling. Despite an increase in reactivity and lowtemperature ignition, the prepared composite powders are insensitive to initiation by electro-static discharge (ESD), making them attractive alternative to analogous thermites having very high ESD sensitivity. In air, the composite powder particles burn faster than reference aluminum particles …

Controlled Reduction Of Graphene Oxide And Graphene Oxide-Carbon Nanotube Hybrids And Their Applications, Samar Azizighannad

Dissertations

Graphene and graphene derivatives are widely used in diverse research and industrial applications. Graphene production on a large scale is carried out by exfoliating graphite oxide and producing graphene oxide (GO), which comprises of graphene sheets with different oxygen-containing functional groups such as hydroxyl, carboxyl, and carbonyl. GO is reduced to reduced graphene oxide (rGO), which has properties that are closer to graphene. Properties of GO and rGO depend upon the oxygen content, and the effect of reducing oxygen content on the aqueous behavior of rGOs is not well understood.

In an effort to understand how properties of rGO change …

Experiments And Modeling Of The Chemo-Mechanically Coupled Behavior Of Polymeric Gels, Nikola Bosnjak

Dissertations

Polymeric materials consist of mutually entangled or chemically crosslinked long njitmolecular chains which form a polymer network. Due to their molecular structure, the njitpolymeric materials are known to undergo large deformation in response to various njitenvironmental stimuli, such as temperature, chemical potential and light.

When a polymer network is exposed to a suitable chemical solvent, the solvent molecules are able to diffuse inside the network, causing it to undergo a large volumetric deformation, known as swelling. In addition to volumetric deformation, this process involves the chemical mixing of the polymer network and solvent molecules, and is typically environmentally responsive. A …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

Numerical And Analytical Methods To Predict Behavior Of Reinforced Ductile Concrete Composites, Mandeep Pokhrel

Dissertations

Structural components constructed with ductile concrete composites, such as high-performance fiber-reinforced cementitious composites (HPFRCC), are known to perform exceptionally well under extreme mechanical and environmental loading conditions compared to traditional concrete. HPFRCC flexural components exhibit enhanced performance in terms of displacement ductility, energy dissipation capacity, and damage tolerance capacity. However, recent research suggests that the flexural behavior of reinforced HPFRCCs in terms of crack progression, reinforcement plasticity, and failure mechanism is significantly different than conventional reinforced concrete. Specifically, the failure mode of flexural members is found to be predominantly through the fracture of longitudinal reinforcement rather than compression crushing of …

The Impact Of Conversion On The Durability Of Calcium Aluminate Cement Concrete Systems, Marwa Mohsen Korayem

Dissertations

The deterioration of infrastructure in North America has resulted in a significant need for concrete repair materials that can be used to maintain service life of these structures. Hydraulic cement based rapid repair materials can be used to repair pavement and bridge deterioration with minimal impact on economic activities such as freight handling or public transportation. While there are many options for use in repair situations, calcium aluminate cements have become more popular recently, particularly in situations where repairs must be completed rapidly.

Calcium aluminate cement (CAC) is a cement characterized by its rapid strength gain, even at low temperatures …

Modeling Single Microtubules As A Colloidal System To Measure The Harmonic Interactions Between Tubulin Dimers In Bovine Brain Derived Versus Cancer Cell Derived Microtubules, Arooj Aslam

Dissertations

The local properties of tubulin dimers dictate the properties of the larger microtubule assembly. In order to elucidate this connection, tubulin-tubulin interactions are be modeled as harmonic interactions to map the stiffness matrix along the length of the microtubule. The strength of the interactions are measured by imaging and tracking the movement of segments along the microtubule over time, and then performing a fourier transform to extract the natural vibrational frequencies. Using this method the first ever reported experimental phonon spectrum of the microtubule is reported. This method can also be applied to other biological materials, and opens new doors …

Schwann Cells In Combination With Gag-Mimetic Scaffolds For Spinal Cord Repair, Sharareh Hashemi

Dissertations

Spinal cord injury (SCI) being a devastating neurological dysfunction can cause extensive irreversible neuronal loss and axonal damage. Fifty-four cases of spinal cord injury per million people occur annually in the United States. Due to the loss of glial cells and demyelination of axons, the neuronal function of surviving neurons is disrupted leading to permanent loss of sensory and motor functions. The glial scar formed by astrogliosis at the chronic stage protects undamaged tissues, but it is known to be a major barrier for axonal regeneration. The limited regeneration capacity of spinal cord makes it challenging to successfully treat the …

Improving Boron For Combustion Applications, Kerri-Lee Annique Chintersingh

Dissertations

Boron has received much attention as a potential additive to explosives and propellants due to its high theoretical gravimetric and volumetric heating values. The challenge, however, is that boron particles tend to agglomerate, have lengthy ignition delays and very low combustion rates. Prior research indicates that boron’s long ignition delays are due to its inhibiting naturally occurring oxide layer, impeding the diffusion of reactants for oxidation. For combustion, current studies report that boron particles have two consecutive stages, but the actual reaction mechanism is poorly understood. Despite many years of relevant research, quantitative combustion data on micron-sized boron particles are …

Supercapacitors With Gate Electrodes, Tazima Selim Chowdhury

Dissertations

A new approach to improve the capacitance of supercapacitors (SC) is proposed in this study. A typical SC is composed of an anode and a cathode; a separator in between them assures an unintentional discharge of the capacitor. The study focuses on a family of structured separators, either electronically active or passive which are called gates. An active structured separator layer has been fabricated and analyzed. The structured separator has characteristics of electrical diode and is fabricated out of functionalized carbon nanotubes (CNT). Improvement of the overall capacitance of SC, equipped with either active or passive structured separators demonstrated a …

Epitaxial Growth Of Iii-Nitride Nanostructures And Their Optoelectronic Applications, Moab Rajan Philip

Dissertations

Light-emitting diodes (LEDs) using III-nitride nanowire heterostructures have been intensively studied as promising candidates for future phosphor-free solid-state lighting and full-color displays. Compared to conventional GaN-based planar LEDs, III-nitride nanowire LEDs exhibit numerous advantages including greatly reduced dislocation densities, polarization fields, and quantum-confined Stark effect due to the effective lateral stress relaxation, promising high efficiency full-color LEDs. Beside these advantages, however, several factors have been identified as the limiting factors for further enhancing the nanowire LED quantum efficiency and light output power. Some of the most probable causes have been identified as due to the lack of carrier confinement in …

N8- Polynitrogen Stabilized On Carbon-Based Supports As Metal-Free Electrocatalyst For Oxygen Reduction Reaction In Fuel Cells, Zhenhua Yao

Dissertations

The sluggish oxygen reduction reaction (ORR) kinetics at the cathode is one of the key factors limiting the performance of polymer electrolyte membrane fuel cell (PEMFC). Platinum-based materials are the most widely studied catalysts for this ORR reaction while their large-scale practical application in fuel cells is hindered due to their scarcity and low stability. Therefore, highly active, low cost and robust non-Pt catalysts are being developed to overcome the drawbacks. Recently, a novel polynitrogen N8- (PN) stabilized on multiwall carbon nanotube (MWNT) was synthesized under ambient condition for the first time by our group and demonstrated high ORR activities. …

Surface-Enhanced Raman Detection Of Glucose On Several Novel Substrates For Biosensing Applications, Laila Saad Alqarni

Dissertations

The small normal Raman cross-section of glucose is considered to be a major challenge for its detection by Surface Enhanced Raman Spectroscopy (SERS) for medical applications. These applications include blood glucose level monitoring of diabetic patients and evaluation of patients with other medical conditions, since glucose is a marker for many human diseases. This dissertation focuses on Surface-Enhanced Raman Scattering primarily for the detection of glucose. Some experiments also are carried out for the detection of the corresponding enzyme glucose oxidase that is used in electrochemical glucose sensors and in biofuel cells. This project explores the possibility of utilizing Surface …

An Electrical Matlab Model Of Plasma Electrolytic Oxidation, Huize Xue

Theses

Plasma Electrolytic Oxidation (PEO), a part of Plasma electrolytic Deposition (PED), has been developing for surface modification of metallic materials in the past 20 years. During PEO process, sample always connect with anode of DC power source, under high temperature, accelerating process of oxidation reaction to from an average and dense oxidation film. A general passage, Plasma electrolysis for surface engineering, written by A.L. Yerokhin, X. Nie gives us a trend of what happened during PEO process but did not determine specific material and value. Linxin Zhu’s Development of PEO invent a new boiling system and investigated relationship between surface …

Optical Properties Of Polymers And Their Applications, Samiha Hossain

Theses

The last decade has witnessed explosive growth in the world of photoactive polymers for a variety of applications in several sectors of the global economy. The need for efficient, reliable, and low-cost data acquisition, storage, processing, transmission, and display technologies has made it necessary for research aimed at addressing these needs. Recent accomplishments in this materials area represent exciting opportunities for major innovations in various fields. However, further work needs to be done to transfer the technology from fundamental R&D to manufacturing. The goal of this study is to provide a better understanding of the optical properties of polymers and …

Magnetic Field Assisted Milli-Scale Robotic Assembly Machine: An Approach To Massively Parallel Swarm Robotic Automation Systems, Yan Liu

Dissertations

The vision of highly parallel, automated manufacturing systems that can build macroscopic products by heterogeneous assembly of many small devices will have a major impact in manufacturing. In this study, a novel milli-scale robotic assembly machine with parallel capabilities, assisted with programmable magnetic field, is developed. The machine prototype consists of a 16x16 array of electromagnets. The dimensions of the electromagnets are 5mm high with an inner diameter of 1.1mm and outer diameter of 2.5mm. All the electromagnets are driven by a 16x16 array of H-Bridges, and an Arduino microcontroller is used to control and program the arrays.

Using the …

Development Of Flexible Nickel-Zinc And Nickel-Iron Batteries, Xianyang Meng

Dissertations

The fabrication of flexible nickel-zinc batteries using a facile mixing of electroactive components for electrode preparation is presented. Polytetrafluoroethylene (PTFE) is found to be an effective binder by reducing concentration polarization, providing chemical/physical stability and enhancing flexibility. The zinc electrode containing PTFE maintains its original porous morphology even after hundreds of cycles while polymers such as PEO show morphology change. Each component, as well as the assembled flexible cells show desired flexibility and stability even under bending conditions.

The fabrication of flexible nickel-iron batteries using printable composite electrodes embedded with multiwalled carbon nanotubes (CNT) is also presented. All the metal …

Analysis Of 3d Printed Ndfeb Polymer Bonded And Organic Based Magnets, Chimaobi Ibeh

Theses

Additive manufacturing (AM), or commonly known as 3D printing, has introduced to the manufacturing and commercial sectors novel ways of reducing production times, decreasing material waste, and enabling end products with multi-material configuration and complex geometric designs. From industrial scale to customer-based printers, AM has revolutionized the approach to manufacturing, prototyping, and designing in the field of medical, automotive, aerospace, biomedical, electronics and customizable products. Recently, additive manufacturing has crossed over to the area of applications in magnetism due to the economic push for the miniaturization of electronic and mechanical devices, reduction in production costs and material & design flexibility. …

Cellulose-Derived Glycosaminoglycan Mimetic For Use In Cartilage Tissue Engineering Strategies, Roseline Dominic Menezes

Dissertations

Articular cartilage has limited healing and self-repair capability due to the absence of vasculature, lymphatic vessels, and nerves. Damage to articular cartilage becomes irreversible leading to formation of osteoarthritis that could severely degrade a person's quality of life. Approximately, 5-10% of cartilage tissue is made up of glycosaminoglycans (GAG), which sequester growth factors as well as provide structural integrity to the native cartilage tissue. Transforming growth factor-beta3 (TGF-β3) is an important growth factor for inducing chondrogenesis in mesenchymal stem cells (MSCs). Bioavailability of TGF-β3 plays a critical role in cartilage repair both in vitro and in vivo. This study evaluates …

Silicon Based Uncooled Microbolometer, Asahel Banobre

Dissertations

During the last decade, uncooled microbolometer infrared detectors have attracted the attention of military and civilian infrared detection and imaging industry due to their significant advantages. In actuality, infrared imaging systems play a critical role in sectors such as thermography (predictive maintenance and building inspection), commercial and civilian applications (vision automotive, surveillance, navigation and fire-fighting), and defense industry (thermal weapon sight, soldier vision and vehicle vision enhancer). Compared with the cryogenically cooled infrared photon detectors, uncooled infrared imaging technology offers advantages such as operation at room temperature, light weight and size, reduced power consumption, easy integration with read-out electronics and …

Structural Studies To Determine The Mechanisms Supporting Multiferroic And Ferroelectric Properties Of Complex Oxides, Han Zhang

Dissertations

Multiferroics are a class of materials which possess both magnetic and electrical polarization with possible coupling between them. They show promise to enable new sensors and data storage devices with novel features, such as the possibility of writing polarization bits with magnetic fields at low power. The coexisting magnetic and ferroelectric order parameters are usually weakly coupled, preventing practical use. The development and study of new classes of materials with large magnetoelectric couplings is of high importance. Understanding the structure of these materials is key to this effort.

As one class of these systems, the RX3(BO₃)₄ has …

Black Silicon – Optical Properties And Applications, Sita Rajyalaxmi Marthi

Dissertations

Crystalline Silicon (c-Si) is one of the most abundant and widely used semiconductors. Si is a semiconductor with indirect bandgap. The average reflectance of Si is about 30% in the visible range of wavelengths. Standard Si solar cells are not entirely useful in the infrared spectrum region. In order to make Si useful in a wide spectral range, the surface of Si is modified to reduce the reflectance of Si. The silicon thus modified is called Black Silicon (BSi).

This dissertation describes the model based on effective medium approximation to determine the effective optical constants, refractive index and extinction coefficient …

Electrical Properties Of Metal/Wse2structures, Zeel Rajiv Gandhi

Theses

The formation of low resistance metal contacts on two-Dimensional layer (2-D) of WSe2 is a big challenge. In this research, a comparative study is presented on the electrical properties of metal/WSe2 Schottky barrier diodes with various metals such as Au, In, Al, and Ga in the temperature range of 80K to 400K well within the domain of thermionic emission theory.

Topics covered here include the factors that determine the Schottky barrier height, the device capacitance, and its current-voltage (I-V) characteristics. I-V curves for different metals on WSe2 are analyzed as function of temperature. Barrier height is determined from Au-nWSe2 Schottky …

Formulation Of Uv Curable Resins Utilized In Vat Photo Polymerization For The Additive Manufacturing Of Gun Propulsion Charge In 3d Printers, David T. Bird

Theses

Formulating resins for Additive Manufacturing (AM), utilizing UV laser stereolithography, is a new technique that makes it possible for the fabrication of complex geometries with high dimensional resolution. This layer by layer photopolymerization approach spans various industrial sectors from adhesives, inks and optical fibers to nanotechnology and biomaterials. UV curable resins such as epoxides, vinyl ethers and other acrylates are important monomers that offer effective mediums for energetic materials, and the potential exists to develop environmentally friendly formulations with suspended energetic materials at various solids loading levels.

Developing techniques for UV curing formulations of highly loaded energetic suspensions is a …