Materials Science and Engineering Commons^™

Characterization Of The Fluid-Dynamic Mixing Of A Bottom Gas-Injected Channel Reactor Using Low-Temperature Modelling, Jay Bernett Gassel

Masters Theses

"Variables influencing the mixing in a single-phase (30.5 x 60 x 606 cm) and a two-phase (20 x 40 x 200 cm) channel reactor model were studied. Tracer and/or neutral density particle techniques were used to determine an eddy diffusivity, De, for the system(s). Three bubbler arrangements were investigated in the one-phase work. A separate apparatus was developed to withstand the corrosiveness of the tetrachloroethylene used in the two-phase work.

Both the electrical conductivity tracer technique and the neutral density particle technique were shown to be feasible experimental techniques for determining an eddy diffusivity in the systems studied. Decreasing liquid …

An Apparatus For The Measurement Of Dc Electrical Conductivity And Seebeck Coefficient Of Semiconductors As A Function Of High Temperature And Oxygen Partial Pressure, George Francis Carini Ii

Masters Theses

"A computer controlled apparatus for the measurement of dc electrical conductivity and Seebeck coefficient as a function of temperature and oxygen partial pressure has been developed. Thermocouples are in electrical and thermal contact with the ends of the specimen bar. This allows both Seebeck and four-wire electrical conductivity measurements to be made in situ. Environmental enclosure of the specimen allows measurements over a range of oxygen activities from 1 to 10^-18 atm. A discussion of the measuring technique with schematics of the apparatus and data retrieval system is made. Results for measurements in selected oxide ceramics are compared to …

The Mg-Sb System, A. A. Nayeb-Hashemi, J. Beverley Clark

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Discussion Of "Lime-Enhanced Reduction Of Sulfide Concentrates: A Thermodynamic Discussion", Arthur E. Morris, Harry Flynn

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Electrochemical Monitoring Of Electrogalvanizing Solutions, Thomas J. O'Keefe, S. F. Chen, E. R. Cole, M. Dattilo

Materials Science and Engineering Faculty Research & Creative Works

The corrosion resistance of steel is vastly improved when a zinc cathodic protective layer is applied. In recent years there has been renewed interest in producing this galvanized coating electrolytically. As with many deposition processes, the control of the operating parameters is very important in order to produce good quality zinc coatings. The homogeneity, ductility and smoothness of the zinc layer are critical. These factors are usually influenced by the electrochemical nature of the solution and organic additives are often used to assist in control. Studies on the polarization behavior of solutions for electro galvanizing electrolytes were made. Cyclic voltammetry …

A Study Of Problem Lead-Zinc Ores Of Southeast Missouri In Terms Of Mineralogy And Galena Oxidation, Michael G. Schroer

Masters Theses

"Recovery problems encountered at some of the St. Joe Lead Company's milling facilities prompted the study of 6 different ores. High and low grade ores had characteristics that varied from poor lead - zinc selectivity to excessive lead losses to the flotation tailings. Three ores from both the Fletcher and Viburnum mills were studied through flotation tests, mill water analysis, and ore analysis using an ore microscope.

The major cause for poor recovery was found to be due to ore oxidation. Not only was lead, in the form of oxides, reporting to the tails, but high levels of copper ions …

Influence Of Oxygen Activity On The Lattice Parameters And Thermal Expansion Of Mg And Sr-Doped Lacro₃, Sutham Srilomsak

Masters Theses

"Lanthanum Chromite, when used as the fuel cell interconnector material is exposed to extremely different oxygen activities on its two surfaces. In addition, it must also form coherent boundaries with the fuel electrode (anode) and air electrode (cathode) layers. In order to accomplish these functions the acceptor doped LaCrO₃ must not only be chemically stable over large oxygen activity ranges, but also have good thermal expansion coefficient of match with both the anode and cathode. Therefore, the objective of this study is to investigate these requirements for Mg and Sr doped LaCrO₃. The study was divided into …

The Effect Of Oxygen Partial Pressure On Oxygen And Carbon Incorporation In Czochralski Grown Single Crystal Silicon, Paul Shane Carter

Masters Theses

"The study herein detailed was made to determine the effect of varying the oxygen partial pressure of a Czochralski type crystal pulling furnace using conventional hardware and remelt silicon on the level of incorporated oxygen and carbon in the single crystal. The oxygen partial pressure was measured by a zirconia type oxygen sensor and controlled by additions of hydrogen or carbon dioxide to the argon purge gas. The oxygen and carbon incorporation measurements were made by the Fourier Transform Infrared (FTIR) method, using the American Standard for Testing Materials (ASTM) standard calibration.

During the study boules which were zero dislocation …

An Investigation Of The Low Voltage Failure Mechanism In Multilayer Ceramic Capacitors, Christopher John Brannon

Masters Theses

"Enhanced leakage current was induced into multilayer ceramic capacitors by the introduction of micro-cracks. These cracks extended from the surface through the electrode layers and were formed by means of thermal shock. The capacitors were then exposed to a low voltage bias and a humid atmosphere. Results indicated that a simple electrolytic solution mechanism may be responsible for the increased conduction, and that the proposed dendritic growth mechanisms may be more complex than necessary"--Abstract, p. ii

Elasto-Composition Waves In Inhomogeneous Solids, R. C. Batra, Manfred Wuttig

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Reply, Paul W. Angel, Chandra S. Ray, Delbert E. Day

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Preparation Of Perovskite Pb(Mg1/3nb2/3)03 Using Pb3nb208 And Mgo, Jyoti P. Guha, Harlan U. Anderson

Materials Science and Engineering Faculty Research & Creative Works

The synthesis of perovskite Pb(Mg1/3Nb2/3)O3 from an equimolar mixture of Pb3Nb208 and MgO was studied by solid‐state reaction techniques. An addition of 1 wt% excess MgO to the stoichiometric composition enhances the formation of the cubic perovskite phase. The absence of free PbO in the initial starting materials minimizes the volatilization loss during firing, thereby reducing the possibility of any compositional change and resulting in a substantial improvement of the perovskite phase purity over the conventional mixed‐oxide processing. Copyright © 1986, Wiley Blackwell. All rights reserved

Tspc/Dc Measurements On Barium Titanate, Harlan U. Anderson, Wayne Huebner

Materials Science and Engineering Faculty Research & Creative Works

Thermally-stimlated polarization / depolarization current (TSPC / DC) measurements were made on high-purity doped and undopod BaTiO3 as a function of applied field, heating rate, dopant level, and Ba:Ti ratio. The form of the TSPC/DC curves is dependent upon both the resistive and ferroelectric properties of BaTiO3. For TSPC spectra, current peaks are exhibited due to the change in in magnitude and direction of the spontaneous polarization with changing crystal structure. In particular, whether the phase transition is first or seoond order influsnaes the existence and magnitude of the current peaks. TSDC measurements are essentially dynamic pyroelectric measurements and as …

Reaction During Sintering Of Barium Titanate With Lithium Fluoride, Jyoti P. Guha, Harlan U. Anderson

Materials Science and Engineering Faculty Research & Creative Works

The reactions occurring during sintering of stoichiometric BaTiO₃ with small additions of LiF were studied at temperatures between 700° and 900°C. BaTiO₃ reacts with LiF to form a cubic solid solution and Li₂TiO₃ During sintering, the cubic solid solution coexists with Li₂Ti0₃ and forms a liquid phase at 740°± 5°C. The occurrence of a liquid phase at this temperature results in an enhancement of the sintering process and leads to the development of a highly dense microstructure. Copyright © 1986, Wiley Blackwell. All rights reserved

Glass Experiments In Space, Norbert J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

Current and potential glass research under microgravity includes studies of minimum cooling rate, homogeneous nucleation, diffusion, surface tension and enrichment, fining without buoyancy, avoidance of liquid phase separation, gel synthesis, composites and uniform micro balloons. The experiments do not just anticipate space fabrication but will also provide information and innovation encouraging advanced processing on earth. © 1986.

Oxidation Kinetics Of Polycrystalline Srtio₃ And Lacro₃, Chi-Kung Jerry Yu

Doctoral Dissertations

"The oxidation kinetics of polycrystalline SrTiO₃ and LaCrO₃ were determined by measuring the time and temperature dependence of the weight and conductivity change of reduced samples. A region of fast diffusion followed by a reduced diffusion tail was observed in the TGA measurements. This observation can be interpreted as the initial diffusion along the boundaries and then spreading out into the lattice. The absence of the tail in the conductivity measurements is due to the high electron and hole mobility at the boundaries. The electrical conductivity and TGA results on Nb-doped LaCrO₃ show that at low oxygen …

Characteristics Of A Stirred Bed Reactor Used For Gas-Solid Reactions, Christine Joy Beyke

Masters Theses

“A fluidized bed gas-solid reactor was designed and tested in which most of the fluidization energy is provided by a helical stirrer, with gas being used primarily as a reactant. The bulk gas in which the particles are suspended is practically constant in composition except for the area immediately adjacent to the gas inlet. The reactor is capable of withstanding temperatures up to at least 800°C and can be used with a wide range of flow rates. It is intended primarily as a laboratory tool, with the potential to be scaled up to multikilogram size.

The reactoor is a useful …

High-Temperature Redox Behavior Of Doped Srtio3 And Lacro3, Harlan U. Anderson, M. M. Nasrallah, B. K. Flandermeyer, A. K. Agarwal

Materials Science and Engineering Faculty Research & Creative Works

The stability of high-temperature fuel cell electrodes to their ambient environment is important for the long-term reliability of fuel cells. In this report the behavior of oxide electrode materials as a function of oxygen activity and temperature is considered. Models for the oxidation-reduction behavior of both p- and n-type oxides are presented. These models take into account the absorption and evolution of oxygen which take place as oxygen activity is varied. The resulting instability in electrical conductivity is explained as a consequence of changes in carrier concentration due to variability in ionic defect concentration. The proposed models are applied to …

Dissolution Of Multi-Component Systems, Robin Ashley Murphy

Doctoral Dissertations

"The validity of ideal barrier layer diffusion kinetics was examined in the NaCl/KCl - glycerol and Al₂O₃-CaO-Al₂O₃-SiO₂/slag corrosion systems. Single crystals and dense polycrystalline plates of pure NaCl or KCl exhibit steady-state corrosion rates within 10%, of calculated theoretical values, while dense mixtures of the two salts corrode at rates higher than either pure material. The results are compared to the grooving phenomena of NaCl/KCl bicrystals.

Polycrystalline Al₂O₃ is shown to corrode at the same rate as single crystal sapphire at 1400°C in CaO-SiO₂-Al_{2 …}

Electrochemical Evaluation Of Zinc Electrolyte, Rajesh Kumar Singh

Doctoral Dissertations

"The polarization characteristics of acidified zinc sulfate electrolyte with varying solution chemistries were examined by cyclic voltammetry. An attempt was made to correlate the polarization results with the morphological and current efficiency data in order to develop a better understanding of the more fundamental aspects of impurity and additive behavior during the zinc electrodeposition process.

A statistical screening design program was conducted to determine the effects of certain operating parameters on the nucleation potential of zinc from sulfate electrolyte. The variables studied included: solution temperature, H₂SO₄ and Zn concentration, and scan rate. The solution temperature was found to be the …

Mass Transport Considerations In Electrometallurgical Reactions, Jose Rolando Sami Cuzmar

Doctoral Dissertations

"The research program described is divided into three segments. In the first part, the morphology and kinetic studies of Cd²⁺ removal from ZnSO₄ solutions using Zn dust as a reducing agent are presented. In the absence of impurities, the morphology of the Cd deposit shows the formation of two-dimensional or leaf-like dendrites capable of interlocking and forming agglomerates or balls. The size and strength of the agglomerates depend on the initial Cd²⁺ concentration to Zn metal surface area ratio, the rate of Cd ²⁺ removal, and the reactor geometry. The presence of additives, like Cu²⁺ and …

Comment On “Dielectric Properties Of Lead‐Magnesium Niobate Ceramics”, Jyoti P. Guha

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Feasibility Study Of Fabricating Composite Ceramic Chamber Liners For Small Caliber Automatic Weapons, P. D. Ownby, D. V. Stewart

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Screening Design Test For Cyclic Voltammetric Evaluation Of Zinc Sulfate Electrolyte, R. K. Singh, Thomas J. O'Keefe

Materials Science and Engineering Faculty Research & Creative Works

A statistical screening design program was conducted to determine the effects of certain operating parameters in the cyclic voltametric evaluation of zinc sulfate electrolyte. The variables studied included solution temperature, sulfuric acid and zinc concentrations, and scan rate. Solution temperature was found to be the most significant factor affecting the initial potential, followed by scan rate and zinc concentration. Based on screening design data, mathematical equations were developed to predict polarization behavior of addition-free zinc sulfate electrolytes. A few preliminary tests on the effect of impurities and organic additives, such as Sb(III) and glue, on potential, deposit morphology, and crystal …

An Analysis Of Mill Sound Levels To Aid In The Control And Understanding Of The Grinding Process, Scott Douglas Morrison

Doctoral Dissertations

“An experimental study has been made to evaluate the relationships between grinding parameters and the directional sound levels emitted from the collision of the grinding media with the mill wall for a laboratory batch ball mill.

Discrete frequency and single frequency band sound pressure level measurements were performed to investigate the changes in sound levels with grind time. It was demonstrated that the reduction in sound levels with grind time observed for a narrow sized feed can be used to indicate optimum breakage rates, overall time-based particle size distribution, and ore character.

The relationships established with the discrete frequency and …

The Effect Of Electrodes On The Thermally Stimulated Currents In Sodium Silicate Glass, Ruth Mogrovejo Cuzmar

Masters Theses

“Electrodes play an important role in the study of alkali ion motion in glasses when TSPC/TSDC techniques are used. Silver, gold and combinations of them were used in the study of Na⁺ motion in Na₂O·3SIO₂ glass. The lower temperature peak is not affected by any of these electrodes, so it is attributed to the bulk glass. A second and third peak are strongly dependent on the kind of electrode used. A gold anode is a blocking electrode, and a gold cathode, is partially blocking. There is a tendency for a space charge polarization to form when …

Sintering Of Catio₃ With The Addition Of Caco₃ And Lif, Surapol Pleekram

Masters Theses

"The densification of CaTiO₃ with the addition of 4.74, 5.90, 6.88 mol% CaCO₃ and 22 mol% LiF was investigated over the temperature range 800° to 1050°C, for sintering times ranging from 1 to 216 hours. It was found that CaCO₃ reacts with LiF and to form a liquid at a temperature of about 450°C. This liquid enhances the densification of CaTiO₃ . The densification process was followed by making weight loss, shrinkage and porosity measurements. The microstructural development was determined by scanning electron microscope examination of both fractured and polished surfaces. X-ray diffraction and DTA/TGA were …

The Oxidation Of Dilute Alloys Of Magnesium In Aluminium, Hollis P. Leighly, A. Alam

Materials Science and Engineering Faculty Research & Creative Works

The oxide layers developed during the oxidation of aluminum alloys containing 500 and 1000 PPM of magnesium at 850K were examined with the aid of electron spectroscopy for chemical analysis. The magnesium content of the oxide layers was relatively high because of the preferential depletion of the magnesium atoms from the base alloys. Near the outer surfaces of the oxide layers, spinel (MgAl2O4) was the predominant magnesium-bearing compound. At depth, MgO was more dominant. The preferential depletion of magnesium from the alloys injected vacancies into the material. This led to the formation of defect clusters. The presence of these defect …

Oxygen Activity Dependence Of The Defect Structure Of La-Doped Batio3, M. M. Nasrallah, Harlan U. Anderson, A. K. Agarwal, B. F. Flandermeyer

Materials Science and Engineering Faculty Research & Creative Works

A model for the behavior of donor doped BaTiO₃ as a function of oxygen activity is proposed. Thermogravimetric measurements show good agreement with the proposed model. The results show that donor-doped BaTiO₃ is stoichiometric with electronic compensation of the donor at low oxygen activity, but with increasing oxygen activity, compensation becomes ionic as excess oxygen is absorbed. The possible compensation mechanisms are discussed. © 1984 Chapman and Hall Ltd.

Oxidation-Reduction Behaviour Of La-Doped Srtio3, B. F. Flandermeyer, A. K. Agarwal, Harlan U. Anderson, M. M. Nasrallah

Materials Science and Engineering Faculty Research & Creative Works

Thermogravimetric measurements as a function of oxygen activity were performed in the temperature range of 1200 to 1400° C on a series of lanthanum SrTiO₃ compounds. A model which assumes the absorption of excess oxygen in the structure which compensates the donors by formation of cationic defects is postulated. Comparison of this model with the experimental results show reasonable agreement. © 1984 Chapman and Hall Ltd.