Materials Science and Engineering Commons^™

Surface Treatments' Effects On The Capacitor's Dielectric Performance Under Electro-Thermal Stresses, Haider. M. Umran, Feipeng Wang

Karbala International Journal of Modern Science

Biaxial-oriented polypropylene (BOPP) films are characterized by unfavorable aging behavior because of their poor susceptibility to high temperatures, humidity, and high electric fields. This makes them unqualified to withstand harsh operating conditions, such as in capacitor applications. This study investigates the impact of annealing BOPP samples at 100 °C for five hours after fluorination at different times (15, 30, and 60 minutes) on their electrical and mechanical performance under electro-thermal stresses. Scanning electron microscope (SEM) images confirm that there is an increase in surface roughness and the formation of a dense layer of fluorine-containing groups monotonically with fluorination time. So, …

Low Impedance, Durable, Self-Adhesive Hydrogel Epidermal Electrodes For Electrophysiology Recording, Naiyan Wu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Traditional electrodes used for electrophysiology recording, characterized by their hard, dry, and inanimate nature, are fundamentally mismatched with the soft, moist, and bioactive characteristics of biological tissues, leading to suboptimal skin-electrode interfaces. Hydrogel materials, mirroring the high water content and biocompatibility of biological tissues, emerge as promising candidates for epidermal electronic materials due to their adjustable physicochemical properties. However, challenges such as inadequate electrical conductivity, elevated skin impedance, unreliable adhesion in moist conditions, and performance decline from dehydration have significantly restricted the efficacy and applicability of hydrogel-based electrodes. In this thesis, we report a high-performance hydrogel epidermal electrode patch for …

Engineering Nanofibers: Laboratory Characterization, Microstructural Analysis, And Image Processing Insights, Sayed Ahmadreza Razian, Mohammad Arjomandi, Kaspars Maleckis

UNO Student Research and Creative Activity Fair

Polymer nanofibers have attracted high interest in a wide array of applications, including biomaterial scaffolding, textiles, sensors, reinforcement in composites, and filtration systems. Many of these applications combine nanofibers into non-woven fabrics for better properties and easier manipulation. The properties and performance of nanofiber-based fabrics are affected by various microstructure parameters, including fiber alignment, diameter, and gap sizes between the nanofibers. These structural parameters can be controlled by adjusting various process parameters during manufacturing process, but the exact process parameter-microstructure relationships vary depending on the polymer system and need to be studied individually. The goal of this study is to …

Assessing Adoption Barriers Of Sustainable Packaging In Egypt, Carol Ramses Morgan

Theses and Dissertations

Sustainable packaging has become an essential part of business decisions and corporate directions. With the rise of environmental damages due to improper waste management and unsustainable practices, businesses have a major responsibility to analyze their products’ life cycles and redesign them with sustainability in mind. Applying sustainable packaging could save companies large amounts of resources, therefore cutting costs, while also achieving the legal and social duty as a corporation towards society and the environment. Many developing countries, with specific focus on Egypt, have recently focused on legislative and corporate decisions in order to encourage more sustainable practices. Egypt’s new Waste …

Rational Design Of Peptide-Based Materials Informed By Multiscale Molecular Dynamics Simulations, Dhwanit Rahul Dave

Dissertations, Theses, and Capstone Projects

The challenge of establishing a sustainable and circular economy for materials in medicine and technology necessitates bioinspired design. Nature's intricate machinery, forged through evolution, relies on a finite set of biomolecular building blocks with through-bond and through-space interactions. Repurposing these molecular building blocks requires a seamless integration of computational modeling, design, and experimental validation. The tools and concepts developed in this thesis pioneer new directions in peptide-materials design, grounded in fundamental principles of physical chemistry. We present a synergistic approach that integrates experimental designs and computational methods, specifically molecular dynamics simulations, to gain in-depth molecular insights crucial for advancing the …

Spray-On Sensor Formulations That Enable Detection Of Physical And Chemical Stimuli, Priyanka Shiveshwarkar

Bioengineering Dissertations - Archive

Polydiacetylene based materials have been used for a variety of liquid phase sensing applications. There remains a need for low cost, easy-to-read gas phase sensors for continuous monitoring of physiological parameters and environmental hazards at work or at home. Such sensors could have applications in everyday life, for example as point-of-care or at home testing devices to enable early detection of disease to reduce healthcare costs. Making accessible and non-invasive technologies for monitoring of health and health risks provides individuals with the ability to be proactive in regard to their health and safety. In other examples, environmental monitoring systems could …

Graphene Reinforced Polymer Composite For Small-Scale Vertical Axis Wind Turbine Rotors, Kunal A. Bachim

Mechanical and Aerospace Engineering Theses - Archive

Polymers have evolved as an indispensable asset in various sectors ranging from packaging and construction to energy and aerospace. However, the accumulation of polymer waste poses a necessity to shift toward sustainable waste management processes. Mechanical recycling is a primary method in establishing a circular economy approach for polymers. However, a fundamental challenge arises in this process: a decrease in the mechanical performance of the recycled product compared to that of its pristine counterpart.

This project addresses the challenge of enhancing the recyclability of polyethylene terephthalate (PET) from discarded polymer material by incorporating graphene nanoparticles into the polymer matrix during …

Effect Of Admixtures On Rapid Hardening, Self-Consolidating Concrete, Haley Johnson

Theses and Dissertations--Civil Engineering

Self-consolidating, rapid-hardening concrete is a sought-after product in the market now, however the effects of admixtures on fresh and hardened concrete rheology are still uncertain. This study aims to create a self-consolidating concrete (SCC) using calcium sulfoaluminate (CSA) cement for its rapid-hardening properties, and tests two set time retarders and two viscosity-modifying admixtures (VMAs) to determine how they affect the properties of concrete. The properties studied in this thesis are workability, viscosity, set times, air content, compressive strength, and freeze-thaw resistance of self-consolidating concrete. It was found that tartaric acid creates a very workable SCC with consistent results regardless of …

Restoration Of Strength In Polyamide Woven Glass Fiber Organosheets By Hot Pressing, Mohammad Nazmus Saquib, Edwing Chaparro-Chavez, Christopher Morris, Kuthan Çelebi, Diego Pedrazzoli, Mingfu Zhang, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Thermoplastic composite organosheets (OSs) are increasingly recognized as a viable solution for automotive and aerospace structures, offering a range of benefits including cost-effectiveness through high-rate production, lightweight design, impact resistance, formability, and recyclability. This study examines the impact response, post-impact strength evaluation, and hot-pressing repair effectiveness of woven glass fiber nylon composite OSs across varying impact energy levels. Experimental investigations involved subjecting composite specimens to impact at varying energy levels using a drop-tower test rig, followed by compression-after-impact (CAI) tests. The results underscore the exceptional damage tolerance and improved residual compressive strength of the OSs compared to traditional thermoset composites. …

Insights Into The Characterization And Degradation Of Electrospun Polycaprolactone Scaffolds For Tissue Engineering Applications, Caleb B. Wells

Theses and Dissertations

Electrospun polymeric biodegradable scaffolds are essential in tissue engineering, particularly for Engineered Tissue Vascular Grafts (ETVGs), which promise advancements in treating coronary artery disease, peripheral arterial disease, congenital cardiovascular defects, and renal disease. These scaffolds present a solution to issues with autologous graft availability and durability. While large-diameter grafts in low-pressure environments have seen success, small-diameter grafts in high-flow scenarios remain challenging. Understanding polymeric scaffold degradation and behavior during incubation, especially under dynamic mechanical loading, is vital for clinical translation of small-caliber ETVGs.

This research focuses on characterizing the mechanical and microstructural properties of electrospun polycaprolactone (PCL) scaffolds and their …

Experimental Investigation On Properties Of Sugarcane Bagasse Fiberboard Manufactured With Different Techniques, Amany G. Micheal Prof., Marianne Nabil Girgis Ass. Prof., Omar Mohasen Khalaf Eng.

Architectural Engineering

Within an ongoing research project investigating the use of sugarcane bagasse (SCB) to develop different building materials, this article adopts an experimental approach to determine the effect of the manufacturing technique on proposed composite fiberboards. Two different prototypes of composite fiberboards are developed using (SCB) as a natural fiber, and different matrices are tested. The epoxy resin and polyester resin are used as the alternative matrices. Fiberboards are proposed to be used as cladding boards or as internal furnishing units material instead of using MDF or HDF that exploit the usage of natural soft or hard wood that is unrecyclable, …

Inherently Porous Metal Structures With Sufficient Mechanical Properties Through Direct Writing Of Bio-Based Inks, Havva Eda Aysal

Graduate Theses, Dissertations, and Problem Reports (ETD)

There is currently a burgeoning interest in developing 3D printed metal structures with inherent porosity and sufficient mechanical properties for mass customization in the biomedical field. Current approaches for 3D printing of biocompatible metals rely on powder-bed fusion methods which are energy intensive and utilize large amounts of metal powder that is challenging to recycle. In addition, such methods aim on producing dense parts and porosity generation, within the printed part, is challenging due to the complex physics of the melting pool. Here, a relatively new and promising approach is undertaken to study the 3D printing of inherently porous structures …

Investigation Of The Effect Of Preparation Parameters On The Structural And Mechanical Properties Of Gelatin/Elastin/Sodium Hyaluronate Scaffolds Fabricated By The Combined Foaming And Freeze-Drying Techniques, Mansour Qamash, S. Misagh Imani, Meisam Omidi, Ciara Glancy, Lobat Tayebi

Electrical & Computer Engineering Faculty Publications

This paper aimed to evaluate the effects of different preparation parameters, including agitation speed, agitation time, and chilling temperature, on the structural and mechanical properties of a novel gelatin/elastin/sodium hyaluronate tissue engineering scaffold, recently developed by our research group. Fabricated using a combination of foaming and freeze-drying techniques, the scaffolds were assessed to understand how these parameters influence their morphology, internal microstructure, porosity, mechanical properties, and degradation behavior. The fabrication process used in this study involved preparing a homogeneous aqueous solution containing 8% gelatin, 2% elastin, and 0.5% sodium hyaluronate (w/v), which was then subjected to mechanical agitation at speeds …

Molecular Modeling Of Phenolic Resin For Carbon-Carbon Composites, Ivan Gallegos

Dissertations, Master's Theses and Master's Reports

One of the most difficult challenges associated with space exploration is terrestrial atmospheric reentry due to the high thermal loads generated. Carbon carbon (C/C) composites have been used as heat shielding materials due to their high strengthto- weight ratio and thermal properties and their applications include heat shielding for various high temperature environments. C/C composites are manufactured by polymer-infiltration pyrolysis (PIP) via cycles of curing and pyrolysis of a prepreg which can be costly and take up to several days. Thus, C/C composites ideal candidates for computationally-driven optimization techniques, such as a multiscale Integrated Computational Materials Engineering (ICME) approach, by …

Sustainable Materials For Environment − Multifunctional Material Made From Dead Leaves And Nanostructured Materials For Antibiotic Degradation, Siyuan Fang

Dissertations, Master's Theses and Master's Reports

As environmental pollution from industrial processes and human activities continues to rise, finding efficient approaches to recycle waste materials and degrade persistent contaminants becomes increasingly critical. Dead leaves, an abundant but underutilized biomass, present an opportunity for creating value-added materials if their biocomponents can be preserved and transformed. Simultaneously, antibiotics such as tetracycline are widely found in water bodies but pose serious ecological and health risks, necessitating effective degradation methods. This dissertation addresses these challenges by leveraging natural and nanostructured materials to develop multifunctional products and advanced photocatalytic processes.

Chapter 3 of this dissertation addresses the challenge of converting waste …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …

Robot-Based 3d Printing, Aaron Hoffman

Williams Honors College, Honors Research Projects

Details of a large-format 3D printer created to print experimental materials, test multi-axis print techniques, and quickly print large objects. The printer consists of a 7-axis robotic arm and pellet extruder, which are controlled by a PC. Experimental materials such as recycled polymers or carbon-fiber reinforced materials can be easily tested with the pellet format of the extruder. The printer can perform different printing techniques and can be used to experiment with material properties when using these techniques with different polymers. The print surface is around 5 times larger than the average commercial 3D printer, and the robotic arm provides …

Effects Of Ac Interference On Pipelines Under Cathodic Protection And Cathodic Disbondment Of Pipeline Coatings, Tanner Laughorn

Williams Honors College, Honors Research Projects

This project is split into two parts. The first revolves around AC interference on pipeline steel under cathodic protection. The corrosion rate of steel samples will be measured after they are exposed to varying levels of AC interference and cathodic protection. The results will be used to help develop new guidelines for appropriate cathodic protection of steel pipelines. The second part of this project revolves around the cathodic disbondment of pipeline coatings while under cathodic protection. The disbondment distance, electrolyte pH, and electrochemical impedance spectroscopy will be tested for multiple industry standard coatings under various conditions. The results will be …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Novel Precursors For Carbon Fiber Prepared By Direct Carbonization, Leah Noble

Theses and Dissertations--Chemical and Materials Engineering

For decades carbon fiber-based composites have been most heavily employed in lightweight, structural applications where low density and high strength are necessary, most notably within the aerospace industry. However, the advancement of carbon fiber into a wider array of industries has largely been limited by the high financial and energetic costs associated with its manufacture. Moreover, with an increasing societal emphasis on sustainability, there is an ever-growing desire for low-energy carbon fiber production pathways. One such pathway is the conversion of precursor fiber to carbon fiber by direct carbonization, wherein the energy-intensive, pre-carbonization stabilization step is omitted from the carbonization …

Novel Membrane Materials For Nutrient Recovery From Nutrient-Rich Resources, Km Prottoy Shariar Piash

Graduate Theses, Dissertations, and Problem Reports (ETD)

Global demand for fertilizer production is expanding substantially to meet the food demand of an increasing world population. Anaerobic digestate (AD) of various centralized wastewater facilities contains substantial amounts of ammonium (NH₄⁺) (300-800 mg/L), potassium (K⁺) (13-120 mg/L), and phosphorus (P) (30-100 mg/L)- based nutrients. In addition to reducing energy costs and CO₂ emissions compared to conventional fertilizing raw material manufacturing, recovering nutrients from these waste streams could help mitigate problems such as eutrophication, which otherwise incurs billions of dollars losses to US economy annually. Apart from nutrients, wastewater streams also contain organic pollutants …

Investigating The Role Of Tesserae In Energy Absorption In Shark Cartilage, Molly Dobrow

UNF Graduate Theses and Dissertations

Unlike mammals, shark endoskeletons are composed of cartilage, which is less stiff compared to bone. Despite this structural disadvantage, sharks have risen to become apex predators, with reported maximum posterior bite force estimates approximating 5914 N in bull sharks. Shark jaws are estimated to undergo high cycle loading within the organism’s lifecycle without evidence of failure. Fatigue resistance may relate to mineral distribution within a component of the endoskeletal system – tesserae. Tesserae are thin, roughly hexagonal tiles composed of calcium phosphate hydroxyapatite (HA) crystals and grow by accretion to eventually surround the hyaline cartilage core. Though tesserae dimensions are …

A Novel Magnetorheological Pump Concept For Insulin Delivery, Mohammad Towhidul Islam Rimon

College of Graduate Studies: Theses & Dissertations

Over the past 25 years, awareness of type 1 diabetes has significantly increased, leading to a comprehensive understanding of various aspects, including its genetics, epidemiology, and disease burden. According to the Type 1 Diabetic Index, about 8.7 million people around the world live with this long-term autoimmune disease characterized by insulin deficiency and resultant hyperglycemia. However, the increased availability and utilization of artificial pancreas systems could potentially save 673,000 lives by 2040. Although, the advancement of diabetes technology offers Type 1 diabetic patients more tools to enhance glycemic management and achieve effective outcomes, many patients are still hesitant to adopt …

Fabrication & Characterization Of Hybrid Piezoelectric/Triboelectric Nanocomposite Nanogenerators Via Fusion Deposition Modeling, Khaled El Toukhy

Theses and Dissertations

This thesis aims to discuss the potential of using piezoelectric and triboelectric nanogenerators (PTENGs) for energy harvesting, particularly in the sportswear industry. PTENG's main advantage is that it offers good flexibility making it suitable for high-strain applications. The piezoelectric effect is induced by embedding piezoelectric nanofillers into one of the two triboelectric layers. PTENGs can generate both piezoelectric and triboelectric signals when strained resulting in an enhanced output compared to regular piezoelectric nanogenerators (PENGs) and triboelectric nanogenerators (TENGs). TPU was adopted as the matrix for PTENGs advantageous due to their flexibility, low electrical resistivity, and compatibility with additive manufacturing techniques. …

Modeling Of Asphalt Concrete For Cross-Anisotropic Visco-Elasticity And Heterogeneity, Zafrul Hakim Khan

Civil Engineering ETDs

Asphalt Concrete (AC) is a cross-anisotropic viscoelastic material. This study has developed a methodology to backcalculate the cross-anisotropic properties of the AC layer from the Falling Weight Deflectometer (FWD) sensor and pavement response data from embedded sensors inside a pavement section. This study has also developed a two-way coupled Multiscale Finite Element Model (MsFEM) with Phase Field Fracture (PFF) to study the microstructural heterogeneity and damage of the AC layer based on the actual field loadings. A Finite Difference Time Domain (FDTD) and Machine learning-based backcalculation algorithm were developed to determine the layer thickness and dielectric constant from air-coupled Ground …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Air-Jet Bioprinting Of Stem Cell-Encapsulated Alginate Micro-Droplets For Organoid Biomanufacturing, Mirabella B. Stump

Electronic Theses and Dissertations

Biomanufactured 3D-organoids show promise for modeling and treating various conditions, particularly insulin-dependent diabetes mellitus (type-1 diabetes). Pancreatic islet organoids serve as sustainable sources of insulin-producing β-cells, potentially restoring insulin regulation in patients and providing a long-term solution for diabetes. Hydrogel droplet printing is an emerging technique in regenerative medicine due to its advantageous tunability and biocompatibility; however, challenges of consistency, quality control, and scalability persist. To address these issues, we developed a novel air-jetting based droplet bioprinting system for the generation of monodispersed alginate micro-droplets. The objective of this project was to incorporate human induced pluripotent stem cells (hiPSCs) into …

Thermally Rearranging Polyimide Networks For High-Temperature Applications, William Guzman

Dissertations

High-performance polymers can retain functional properties when exposed to long-term or short-term durations of harsh conditions, such as mechanical action, at elevated temperatures (>177 °C). A mixture of intramolecular and intermolecular forces of and between polymer chains provide excellent property retention at elevated temperatures. Specifically, the highly aromatic nature of high-performance polymer backbones provides outstanding thermal stability, which is typically attributed to π-π stacking. However, the interrelationship between thermal stability and high aromaticity creates a challenging structure-processing relationship paradigm, which causes poor polymer processability in most high-performance polymers. Herein, it was demonstrated that rationally designing a crosslinking phenylethynyl imide …