Materials Science and Engineering Commons^™

Fabrication Of Alumina Membranes From Uv Resin– Alumina Particle Slurries, Dominique Henry Porcincula

Master's Theses

Ceramics membranes are made in a wide variety of different techniques using a wide variety of different materials. However, many of the common techniques utilize a slurry of ceramic particles, additives, and either organic solvent or water that is shaped into a membrane, left to dry, and then sintered together. Drying is a time consuming process, often requiring several hours for the liquid medium to evaporate. Defect formation caused by development of partial pressures across the drying membrane, including cracks and warpage, also typically occurs during the drying process. To address this, slurries of ceramic particles made with a low …

A Comprehensive Review On Metal Oxide-Nanocellulose Composites In Sustainable Active And Intelligent Food Packaging, Kalpani Y. Perera, Amit Jaiswal, Swarma Jaiswal, Dileswar Pradhan

Articles

The aim of this article is to provide an overview of the potential advantages and drawbacks of nanocellulose and metal oxide-based composites in food packaging. These materials offer improved mechanical and barrier properties, as well as antioxidant and antimicrobial benefits that extend the shelf life of food products. Nanocomposite structures protect food from various physiological factors and immobilize enzymes, while metal oxide nanoparticles provide antibacterial effects against Gram-positive and Gram-negative bacteria. However, there are concerns regarding the safety of nanoparticles and their potential migration into packaged food during processing and storage. This article explores these issues and highlights the need …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Cellulose Materials For Drug Delivery Applications, Reham Mohamed

Mechanical Engineering Theses

Non-healing wounds are a growing global public health concern due to inadequate or ineffective therapeutic products available. Cellulose-based biopolymers are attractive wound dressing materials due to their biocompatibility, biodegradability, non-toxicity, and cost-effectiveness. This study aims to design and fabricate solid dosage formulations using carboxymethyl cellulose (CMC) and ethyl cellulose (EC) to facilitate multi-stage releases of phenytoin (PHT) and tetracycline hydrochloride (TCH) from plain carriers, fibers/films composites, and layer-by-layer fiber composites. Results from in vitro drug release assays demonstrated a time-dependent release up to 8 hours from PHT-loaded EC fibers, while TCH-loaded CMC films exhibited a rapid release within 5 minutes. …

Interfacial Thermomechanical Behavior Of Hybrid Carbon Fibers, Sriraj Srihari

Doctoral Dissertations and Master's Theses

The carbon fiber/epoxy interface is of great importance in composite design due to its load transfer mechanisms from the weak epoxy to the stronger fiber. Improving the strength of the interface reduces the risk of failure at the interface and improves the load transfer to the fiber. In this study, two types of nano-species ZnO nanowires and nickel-based metal organic frameworks were grown on carbon fibers to improve the interfaces. The interfacial mechanics of the enhanced fibers are evaluated using nanoindentation studies. Composite samples with Aeropoxy matrix and vertically aligned fibers are fabricated for this purpose. A Bruker TI-980 TriboIndenter …

Synergistic Effect Of Nanoclay And Barium Sulfate Fillers On The Corrosion Resistance Of Polyester Powder Coatings, Jinbao Huang, Marshall Shuai Yang, Chengqian Xian, James Joseph Noel, Yolanda S. Hedberg, Jian Chen, Ubong Eduok, Ivan Barker, Jeffrey Daniel Henderson, Haiping Zhang, Liqin Wang, Hui Zhang, Jesse Zhu

Chemistry Publications

No abstract provided.

Investigating The Rheological Behavior Of A Simple Yield Stress Fluid Under Shear Flows, Francesco Accetta

Theses

Many soft materials display unique and complex rheological behavior characterized by a transition from a solid-like to a fluid-like state upon the application of a force that exceeds the threshold to flow, known as the yield stress. Yield stress fluids are found in a wide range of commonly encountered materials including microgels, emulsions, and foams, and have been widely studied by rheologists over the last several decades. Carbopol is a popular polymeric microgel system as it displays simple, non-thixotropic rheological behavior and is typically seen as an ideal yield stress fluid. Previous research has demonstrated the reproducible behavior of shear …

Glass Bubbles Grafted With Polymer Brushes For Liquid Hydrocarbon Fire Extinguishment, Randall Snipes

All Dissertations

The current most efficient solution to fighting liquid pool fires involves the use of firefighting foams containing fluorinated surfactants. The physiochemical properties of these foams are considerably different to all other currently available firefighting foams. Fluorinated surfactants lower the surface tension to a point where the foam solution draining from the foam structure forms a continuous aqueous film on the surface of a volatile hydrocarbon fuel, adding an additional barrier to fuel vapor diffusion to the burning fire. For this reason, these foams qualify as aqueous film forming foams (AFFFs). However, fluorinated compounds are extremely harmful for the environment due …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …

Double Cantilever Beam Mode-I Testing Validation In Large-Scale Additive Manufacturing Carbon Composite, Luis Alfonso Camacho

Open Access Theses & Dissertations

Testing for mechanical properties for additive manufacturing has been based on already existing standards for traditional manufacturing methods. For composites in large scale additive manufacturing there is a research gap in bond strength and fracture toughness for a single layer interface. By using Double cantilever beam Mode I, this thesis manuscript validates testing parameters and protocols to describe the intricacies of ABS matrix 20 wt.% carbon filled composite, specifically on the layer-to-layer interface. Studies suggest that fracture toughness is sensitive to process parameters, like deflection speed and sharpened crack tip at the layer interface of BAAM 3D printed part and …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Carbon Fibers From Athabasca Oil-Sand Asphaltenes, Blake Reardon

All Theses

Carbon fibers possess ultra-high specific strength and modulus. Therefore, the material is popular in aerospace, automotive, and sports industries. Approximately 95% of all carbon fibers are spun from a high-cost precursor, polyacrylonitrile (PAN). There is a need for a cheaper grade of carbon fiber for low-cost applications because about half of carbon fiber cost is associated with precursor cost. A promising alternative to the high-cost PAN precursor is petroleum-based asphaltene. Asphaltenes are highly aromatic and have a high carbon content but lack the purity of the PAN precursor. Processes like the molten- sodium desulfurization upgrading have been used to harvest …

Flow Through Processing Of Nanocellulose For Space Exploration Applications, Dylan Seiffert, T. E. Kidd

Summer Undergraduate Research Program (SURP) Symposium

Nanocellulose is synthesized from cellulose, which is the most abundant organic molecule found in nature. Nanocellulose solids are biodegradable and have a strength-to-weight ratio eight times that of steel¹. The production of nanocellulose solids is challenging due to the large volume loss that occurs during the curing process as well as the time and cost associated with ultrasonic processing. The loss of volume during curing often results in cracking and deformation of the cured solid. The issues caused by the large volume loss can be mitigated using additives that do not compromise the strength, shape, or machineability of …

Molybdenum Disulfide (Mos₂) As A Nanocellulose Substrate, Mariana Torres, Dylan Seiffert, Elise Hong-Miller, T. E. Kidd

Summer Undergraduate Research Program (SURP) Symposium

Cellulose is a substance abundant in nature, found in fruits and vegetables, plant cell walls (National Center for Biotechnology Information, 2023), and wood (Sjostrom, 1993). The abundance of cellulose is attributable to its linear chemical structure, as it is composed of long strands of glucose molecules linked together by hydrogen atoms, which enable the substance to withstand significant pressure without breaking (Rongpipi et al., 2019). This property—known as high tensile strength—is joined by its non-toxicity and sustainability, given cellulose may be degraded and renewed naturally (Kaur, 2021). These various properties indicate versatility, and its resultant current and desired uses—such as …

Impacts And Applications Of Vegetable Glycerin On Nanocellulose, Elise Hong-Miller, Dylan Seiffert, T. E. Kidd

Summer Undergraduate Research Program (SURP) Symposium

Nanocellulose is created by breaking down cellulose, the most common organic molecule found in nature. Nanocellulose has attractive properties, such as a very high strength-to-weight ratio, for many different applications. A major challenge is that nanocellulose has a very high shrinkage % (~90%) when it is dried, as well as a strong probability to crack. Different additives can be added in varying amounts to either mitigate or intensify these aspects, as well as affect its drying conditions. This investigation is helping the National Aeronautics and Space Administration (NASA) and the U.S. Army to find a use for this highly renewable …

Measurement Of Thermal Conductivity Of Epoxy Resin Reinforced With Different Weight Ratios Of Glass And Carbon Powders, Edrees Edaan Ghadeer

Al-Bahir

The effect of thermal conductivity was studied on the composites prepared before and after reinforcement with different weight fractions (10, 20, 30, 40, 50, 60 wt %), using a Disc Lee's device, and the dispersion of the filler was studied by morphological analysis of the complexes using scanning electron microscopy (SEM). The (SEM) of glass composite powders, showed a smooth surface with a chance of forming very few voids, clusters and blisters on the surface of the sample, which increased with the increase of the weight fractions of the filled powder. While the composites filled with carbon powders show smooth …

Biopolymer-Based Sustainable Food Packaging Materials: Challenges, Solutions, And Applications, Kalpani Y. Perera, Amit Jaiswal, Swarna Jaiswal

Articles

Biopolymer-based packaging materials have become of greater interest to the world due to their biodegradability, renewability, and biocompatibility. In recent years, numerous biopolymers—such as starch, chitosan, carrageenan, polylactic acid, etc.—have been investigated for their potential application in food packaging. Reinforcement agents such as nanofillers and active agents improve the properties of the biopolymers, making them suitable for active and intelligent packaging. Some of the packaging materials, e.g., cellulose, starch, polylactic acid, and polybutylene adipate terephthalate, are currently used in the packaging industry. The trend of using biopolymers in the packaging industry has increased immensely; therefore, many legislations have been approved …

Interlaminar Tensile Properties Of Unidirectional And Woven Carbon Fiber Reinforced Toughened Epoxy Laminates, Eric Timothy Casey, Sean Mckalip Thompson

Materials Engineering

This project aims to develop a dataset on interlaminar tensile strength comparing unidirectional and woven thermoset matrix carbon fiber composites keeping ply count, matrix material, and fiber diameter constant. The interlaminar tensile strength is an important property relating to the delamination failure mode. Interlaminar tensile strength is determined using the ASTM D6415 testing standard. This test is a modified four-point bend test using a 90° curved beam test specimen. Laminates were produced by laying up pre-impregnated carbon fiber sheets onto a curved beam tooling. The unidirectional laminate was produced with 20 plies in a [0,0,90,0,0]₄ layup pattern. The woven …

Effect Of Environmental And Ultraviolet Degradation On The Albedo Of Polyethylene Sheet Materials For Improved Energy Harvesting By Bifacial Photovoltaic Power Plants, William A. Jang, Roxy H. Jackson-Gain

Materials Engineering

Solar energy farms typically utilize monofacial photovoltaic (mPV) cells in their arrays to capture direct sunlight to produce renewable energy. However, the efficiency of these farms can be increased by 2 – 6% through the implementation of bifacial photovoltaic cells (bPV). These bPV cells function by capturing incident ultraviolet (UV) light energy that is reflected off the surface to increase its overall energy production. The amount of UV energy that is reflected is dependent on the albedo value of surface, which is a measure of energy reflectance. In this study, samples of unreinforced polyethylene (PE), scrim-reinforced polyethylene (SR-PE), and woven …

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

Surface Characterization Of Low-Density Polyethylene Mulch, Risha Shah

Materials Engineering

Plastic pollution in aquatic systems has traditionally been highlighted in past and current research due to the increase in plastic production every year. Unfortunately, quantitative and qualitative data regarding plastic pollution on land systems such as agricultural mulch is limited. Agricultural mulch breaks down into macroplastics and then degrades into microplastics. The microplastics investigated in this study are all secondary microplastics: microplastics that form due to weathering of larger fragments of plastic. Weathering can occur due to a variety of factors; however, UV radiation and mechanical weathering have been the factors of focus on most current research in microplastic formulation. …

Piezoelectric And Conductive Polymer Based Flexible Devices Enabling Cardiovascular Health Sensing And Energy Harvesting, Andrew Closson

Dartmouth College Ph.D Dissertations

Piezoelectric materials show great promise for low-power wearable and implantable sensing, but their rigidity makes it challenging to integrate them with biological tissue. To address this, researchers have started exploring polymer-based functional materials that offer flexibility and are suitable for interfacing with the human body. However, these materials are still in their early stages, and a framework is necessary to illustrate how these materials, in conjunction with novel fabrication techniques and device designs, can enable the development of multi-functional sensing and energy harvesting devices.

This thesis utilizes highly scalable fabrication methods for functional polymers to build and test a flexible …

Synthesis And Characterization Of Polyaniline-Based High-Performance Carbon For Energy Storage Applications, Udeshika Kangane Arachchige

Electronic Theses & Dissertations

With the increase in global population, the demand for the energy required for daily activities including household necessities, electronic and electric devices, etc. enhances at an alarming proportion. Under these circumstances, supercapacitors (SCs) have attracted great attention as electrochemical energy storage devices. Nowadays, most commercially available supercapacitors are composed of metallic compounds. Due to the high consumption, and limited availability of these elements, it is necessary to find an alternative, effective, low-cost materials in place of using it. With the purpose of achieving high electrochemical performance, this research work focuses on developing carbon derived from polyaniline (PANI) as an efficient …

Development Of Novel Sensor Coating Methodology To Enable Understanding Of Fouling Mechanisms On Ion Exchange Membranes, Andrew Ulmer

Honors Theses

As populations expand and natural water resources are depleted, severe droughts and limited access to clean water have become an increased threat to areas across the world. Effective and economic water treatment methods such as electrodialysis (ED) are vital for combating these threats, especially in developing nations and secluded locations. Organic foulant adsorption on the surface of ion exchange membranes severely limits the capabilities of water desalination systems such as ED along with significantly increasing maintenance costs. Understanding characteristics such as the total amount and rate at which these foulants at specific concentrations adsorb and desorb to the membranes is …

Introduction To Data-Driven Systems For Plastics And Composites Manufacturing, Saeed Farahani, Srikanth Pilla, Yun Zhang, Fausto Tucci

Mechanical Engineering Faculty Publications

Applications of high-performance plastics and composites have widely been expanded to various industries due to their superior properties, such as high strength-to-weight ratio, chemical resistance, and thermal/electrical insulation. However, the numerous possible combinations of polymers and reinforcements/fillers, the variability of these materials, and their complex manufacturing processes pose challenges in terms of efficiently developing new plastics and composites, accurately modeling their properties, and effectively monitoring and controlling their manufacturing processes. Integrating data-driven techniques, such as machine learning, artificial intelligence, and big data analytics, is a promising pathway to overcome these challenges as it is demonstrated by the state-of-the-art research works …

Utilization Of Cellulose Symbiotic Culture Of Bacteria And Yeast (Scoby) With Sweet Tea Media As Methylene Blue And Brilliant Green Biosorbent Material, Leonard Mateus Sigiro, Ahmad Maksum, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The cellulose from Symbiotic Culture of Bacteria and Yeast (SCOBY) can be used as a biosorbent for dye adsorption, such as Methylene Blue and Brilliant Green. This study used sweet tea with a 6% of sugar concentration and 14 days of fermentation time to synthesize biosorbent material from SCOBY. The results from this synthesis are then characterized using FTIR, SEM, and BET. From the result of characterization, it was found that SCOBY has pores formed from cellulose. The results of the average pore size are 1.5976nm with a pore volume of 0.229cc/g, while the specific surface area is 143.244m2/g. The …

Enhancing Compatibility And Mechanical Properties Of Natural Rubber Composites, Krisma Yessi Sianturi, Adam Febriyanto Nugraha, Belle Kristaura, Mochamad Chalid

Journal of Materials Exploration and Findings

Pure natural rubber (NR) exhibits low mechanical properties, necessitating the incorporation of additives like vulcanizing agents and fillers. Carbon black and silica, conventional fillers, are relatively expensive and not environmentally friendly. This study explores using Oil Palm Empty Fruit Bunch (OPEFB) fiber as an affordable, abundant, and biodegradable alternative filler for NR. However, compatibility issues arise between the nonpolar NR and the polar OPEFB fiber. A latex-starch hybrid coupling agent (CA (NR-St)) was added to the composite formulation to address this. NR, OPEFB fiber, and the coupling agent were mixed using an open roll mill with a 10 phr OPEFB …

Analytical And Experimental Investigation Of Interphase And Dispersion Effects On The Mechanical Stiffness Of Cellulose Nanocomposites, Will Goldberg

McKelvey School of Engineering Graduate Student Theses & Dissertations

The effect of dispersion and interphase properties on the elastic behavior of cellulose nanocomposites was investigated using a number of composite models, experimental data and a thorough literature review. Cellulose nanocomposites consisting of soy protein isolate (SPI) and cellulose nanocrystals (CNC) or polydopamine coated cellulose nanocrystals (PD-CNC) were prepared via solution casting method and tested for mechanical stiffness. These outcomes were compared to standard composite models as well as novel methods adapted from the literature that incorporate data regarding dispersion quality and interphase properties. The literature review verified that both dispersion and interphase properties are highly dependent on interfacial chemistry …