Materials Science and Engineering Commons^™

The Research Of Organic Electrolyte Solutions For Li-Ion Batteries, Quang-Chao Zhuang, Shan Wu, Wen-Yuan Liu, Zhao-Da Lu

Journal of Electrochemistry

The characteristics of organic electrolyte solutions and its influences on the ion conductivity are summarized. The chemistry and electrochemistry of organic electrolyte solutions and characteristics of ordinary organic solvents are introduced. Progresses in studies of organic electrolyte solutions such as electrolyte salts, organic solvents, additives in recent years are reviewed, current situation of the studies of organic electrolyte solutions were also discussed.

New Progress Of Intrinsic Conducting Polymers' Application, Wan Chen, Cheng-Hao Liang, Yang Xie

Journal of Electrochemistry

As a kind of functional polymer, the intrinsic conducting polymer has the special chemical, electrochemical and optical properties. So it has wide application such as batteries, electromagnetic wave shielding, electroluminescent etc. Recent development and the problems of the intrinsic conducting polymers' application were briefly reviewed in this paper.

Thermal Effects On The Measurement Of Photocurrent At Anodic Films On Silver Electrode, Yuan Gu, Zhi-Yu Jiang

Journal of Electrochemistry

The influence of heat on the photocurrent of Ag electrde in alkaline solution was investigated by measuring photocurrent, photothermal signal and thermal current under the irraiation of laser beams with the wavelengths of 488 nm and 532 nm. It was found the photocurrent atthe Ag₂O film was influenced by the temperature change at the electrode surface under the irradiation of light. During the electrochemical transfer between Ag, Ag₂O and AgO in the anodic filmthe surface temperature changed obviously due to the different absprptance of the surface subrstances.It was suggested by comparing the voltammograms, photocurrent curves and …

Study Of Hydrogen Diffusion Behavior In Hydrogen Storage Alloy Mlni3.75Co0.65Mn0.4Al0.2 With Potential Step Method, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Potential step method was employed to study the hydrogen diffusion behavior in hydrogen storage alloy MlNi_3.75 Co_0.65Mn_0.4Al_0.2 with various depth of discharge (DOD) at ambient temperature and with 50% DOD at various temperatures. It was found that hydrogen diffusion cofficient in the hydrogen storage alloy increaes with the increase in DOD at ambient temperature. and for the alloy with 50% DOD, the hydrogen diffusion coefficient increases with the increase in temperature and the activation energy for hydrogen diffusion in the alloy is 19.87 kJ/mol.

Research Progress On Proton Exchange Membranes Of Fuel Cells, Jing-Rong Yu, Dan-Min Xing, Fu-Qiang Liu, Jian-Guo Liu, Bao-Lian Yi

Journal of Electrochemistry

The proton exchange membrane fuel cells (PEMFC) use proton exchange membranes(PEM) as their electrolytes. The performance of the PEMFC is strongly dependent on the characteristics of the PEM. In this paper, the requirements of the PEM utilized in the PEMFC were analyzed. The per-fluorinated, partially fluorinated and non-fluorinated PEM were introduced respectively. The structures, preparation, properties of the various types of PEM and their applications in the PEMFC were also discussed in detail.

The Influence Of Synthesis Conditions On The Electrochemical Properties Of Spinel Limn2O4, Jun-Feng Xu, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of spine LiMn₂O₄ synthesized via a solid state reaction were investigated. Electrolysis MnO₂(EMD), Li₂CO₃ ,LiOH and LiNO₃ were used as the initial materials. It was found that the electrochemical properties of LiMn₂O₄ were strongly influenced by the synthesis conditions. The LiMn₂O₄ sample sprepared via the reactionof EMD and LiNO₃ showed the best properties for a lithiumion intercalation reaction. The procedure includes two steps:pretreatment at 280 ℃ for 6 hours to initiate the permeation of melting LiNO₃ into the microporesof EMD …

Adsorption And Oxidation Of Methanol On Pt And Sb, S Modified Pt Electrodes Using Cyclic Voltammetry And Eqcm, Guo-Liang Chen, Sheng-Pei Chen, Heng Lin, Xing-Hong Zheng, Shi-Gang Sun

Journal of Electrochemistry

The processes of adsorption and oxidation of methanol on Pt, Pt/Sb ad and Pt/S ad electrodes were studied by using cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM). The results demonstrated that the oxidation of methanol depends strongly on oxidation states of electrode surface. Sb adatoms on Pt surface can adsorb oxygen at relatively low potentials, and exhibit catalytic effects for methanol oxidation. In contrast to Pt electrodes, the oxidation peak potential of methanol in this case negatively shifted to about 130 mV. In a contrary, the oxidation of S_ad atoms consumes oxygen species of Pt electrode surface. As …

Study On Electrochemical Behavior Of Copper In Nh3 ·H2O Solution Medium Including K3[Fe(Cn)6] During Cmp, Yue-Hua Hu, Han-Wei He, Ke-Long Huang

Journal of Electrochemistry

Influence of medium pH value and passivator concentrations on the copper passivation and CMP process were studied by electrochemical measurement technologies, relations of the film thickness and tightness with polishing process and polishing rates were investigated. Electrochemical variables influencing polishing process and rates were found out. Electochemical mechanism of polishing processes were explained by corrosion potential and corrosion current density. A recipe of K₃[Fe(CN)₆] as passivator and nano sized γ-Al₂O₃ as abrasives in medium of NH₃·H₂O solution was confirmed reasonable. It is shown that the conditions of polishing process …

Study On The Anticorrosion Of Ld-2 Compound Inhibitor On Reinforcing Steel In Seawater, Rong-Gui Du, Zhou-Cheng Wang, Ruo-Shuang Huang, Rong-Gang Hu, Bing Zhao, Jian-Guang Tan, Chang-Jian Lin

Journal of Electrochemistry

The effect of LD-2 compound inhibitor developed in our laboratory on its anticorrosion action on the reinforcing steel in concrete immersed in seawater was shown in this paper. The corrosion behavior of the reinforcing steel in seawater was studied using electrochemical techniquesand immersion tests. The polarization curve of the reinforcing steel immersed in seawater showedthe free corrosion potential of the steel increased by 0. 220 V (vs. SCE), and the corrosion current decreased by two orders of magnitude by adding 25 g⋅L^-1 compound inhibitor to the seawater. The potentiodynamic anodic polarization curve of reinforcing steel in the seawater with …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (September 1 – November 30, 2001) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including HT- 9, EP 823 and 422. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these alloys will be evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. The extent and morphology of cracking of these alloys will further be evaluated …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823: Task 10, First Quarter Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The objective of this task is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. The test material will be thermally treated prior to evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The overall results are expected to provide a mechanistic understanding of high-temperature deformation behavior of Alloy EP-823 as a function of heat treatment.

Highlights of Accomplishment

• …

Analysis Of Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

We examined stainless samples that were exposed to LBE in experiments conducted by the Russians, under contract to Los Alamos. We examined both corroded and uncorroded samples using the Scanning Electron Microscope (SEM), the Energy Dispersive X-Ray (EDAX) Spectroscopy, and the X-ray Photoelectron Spectrometer (XPS). We found that the surface of the corroded sample is covered by oxygen-containing compounds, presumably mostly iron oxide. In samples exposed for shorter times or lower temperatures, we found that some areas were covered by an oxide layer, and some areas was uncovered. We found that the level of Cr in the uncovered area is …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report August 16,2001- November 15, 2001, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application.

Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. The transport of oxygen and corrosion products, their interaction and variation of corrosion/precipitation along the flow are not well understood.

The first subtask of this project involves using a …

Capillary Flow In Interior Corners: The Infinite Column, Mark M. Weislogel

Mechanical and Materials Engineering Faculty Publications and Presentations

Capillary flow of a sinusoidally perturbed liquid column in an interior corner of infinite extent is solved using lubrication theory. Due primarily to the length scales selected to nondimensionalize the momentum equation, an analytic time scale governing the settling of the perturbation is determined. The time scale, which is shown to be independent of a steady base state flow, proves useful in rapidly predicting transients for surface settling in certain liquid-bearing tanks of spacecraft employing interior corners for fluids management purposes. The asymptotic analysis is extended to address flows along interior corners whose faces are slightly nonplanar. The generalized formulation …

Highly Plasma Etch-Resistant Photoresist Composition Containing A Photosensitive Polymeric Titania Precursor, Tony D. Flaim, Douglas J. Guerrero, Michelle R. Fowler, William Joseph James, Vladimir Petrovsky, Harlan U. Anderson

Chemistry Faculty Research & Creative Works

A composition is derived from an addition polymerizable organotitanium polymer which upon exposure to an oxygen plasma or baking in air, is converted to titanium dioxide (titania) or is converted to a mixed, titanium-containing metal oxide. The metal oxide formed in situ imparts etch- resistant action to a patterned photoresist layer. The composition may also be directly deposited and patterned into permanent metal oxide device features by a photolithographic process.

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (June 1 – August 31, 2001) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The subject task entitled “Hydrogen-Induced Embrittlement of Candidate Target Materials for Applications in Spallation-Neutron-Target Systems” had commenced during the quarter ending on August 31, 2001. A research account has been established, contracts for both faculty and students have been prepared, and efforts are well underway to embark on the related research activities, as proposed.

As the title of this project implies, the primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallationneutron- target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). …

Current Oscillations In The System Of Carbon Steel/Phosphoric Acid/Platinum, Shao-Yuan Shi, Jin-Ping Wu, Jing Liu, An Lin

Journal of Electrochemistry

The periodic,aperiodic, chaotic and mixed-mode oscillations can occur in the process of the anodic electrodissolution of carbon steel in the solution of dilute phosphoric acid. More plentiful dynamic behaviors can be found in this system compared with the system of Fe/H₃PO₄/Pt.

A New Method For Impregnating Nafion Solution Into The Electrode Of Pemfc, Qian Tang, Ming Han, Bao-Lian Yi, Zhi-Yin Lin

Journal of Electrochemistry

We have developed a new method for impregnating Nafion solution into the catalyst layer of homemade hydrophobic electrode using capillary process. Those electrodes show better performance and higher utilization of catalyst (detected by CV and TEM) than traditional spray method in PEMFC. According to the results of SEM photograph and linear-analysis of sulfur and platinum for the electrode cross-section, we can conclude that the resin is uniform in the catalyst layer and has almost same depth as catalyst in the impregnated electrode. While in traditional method resin is not uniform in the catalyst layer and penetrates into the diffusion layer, …

The Coulostatic Method For Evaluating Corrosion In Reinforced Concrete, Yong-Tao Zhao, Jian-Hua Wu, Chang-Jiu Zhao

Journal of Electrochemistry

In the present paper, the application of the coulostatic method to the corrosion of steel in concrete was reviewed. By comparing with other electrochemical techniques, the results obtained in the previous work reveal that the coulostatic method is an interesting alternative to the usual procedures for estimation of corrosion rate, and is better than them in some respects. The main advantages are as follows. The signal to be used can be instantaneous and as small as desired, so the electrode is minimally perturted during the measuring process. In addition, it is as rapid and quantitative, and at least as reliable …

Characterization And Electrochemical Investigation Of Boron-Doped Mesocarbon Microbeads Anode Materials For Lithium-Ion Battery, Mao-Hui Chen, Guo-Tao Wu, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The anodic performances of boron doped and undoped mesocarbon microbeads(MCMBs) were comparatively studied and the structures were characterized by XPS, SEM, XRD and electrochemical measurements. It was found that boron doping samples greatly increased the degree of graphitization and the crystallite size, leading to quite different morphology. Electrochemical discharge/charge cycle tests indicate that lithium intercalation occurred at a little higher potential for the boron doped MCMBs, being attended by greater irreversible capacity loss.

Microstructure And Electrochemical Properties Of The Melt-Spinning Zr0.9Ti0.1(Ni, Co, Mn, V)2.1 Alloy, Ming-Fen Wen, Yu-Chun Zhai, Lian Chen, Min Tong, Hua Zhen, Rong-Jun Ma

Journal of Electrochemistry

The microstructure and electrochemical properties of Zr_0.9Ti_0.1(Ni,Co,Mn,V)_2.1 alloys prepared by both the melt-spinning method and the conventional induction melting were investigated. XRD studies show that Zr_0.9Ti _0.1(Ni,Co,Mn,V)_2.1 alloys at as-cast, melt-spinning and annealing are all face center cubic structure with C₁₅ laves phase, the higher the melt-spinning rate, the more the amorphous content. The electrochemical measurements show that melt-spinning alloys have better active behavior, low discharge capacity (< 280 mAh/g); but after annealed, the alloys are activated completely with 30 cycles, the capacities about 340 mAh/g are higher than those of as-cast and melt-spinning alloys; the annealec alloys have a better cycle stability than that of as-cast alloy, and the higher the melt-spinning rate is, the more stable the alloy becomes; at 300 mAh/g current density, the capacity of annealed 40 m/s alloy is up to 85% of the maximum capacity after 800 cycles, the capacity decay rate is about 6.9%.

In Situ Ftir Reflection Spectroscopy Of Bioelectrode, Sa-Ying Dong, Guang-Yu Zhao, Yuzhu Gao, Guang-Zhang Chen, Ming-Xiang Lv

Journal of Electrochemistry

In situ FTIR reflection spectroscopy was used to study mediated enzyme electrode and immunoelectrode. We determined and analyzed IR characteristic spectra of GOD and glucose by the use of potential difference spectra and single beam subtractive spectra. At last, we explored the IR absorption characters of enzyme-immunoelectrode.

Codeposition And Corrosion Resistance Of Nickel-Cerium-Phosphorus Amorphous Alloys, Jiang Liu, Xiong Jiang, Lin-Cai Jiang, Ze-Shan Zhu

Journal of Electrochemistry

The possibility of electrodeposition of rare earth alloys from aqueous bath was investigated using varous techniques such as linear potential sweeping, cyclic voltammetry, electrodepositon at constant potential etc. The Ni-Ce-P alloys with different cerium content were electrodeposited from a weakly acidic solution containing CeCl₃, NaH₂PO₂ and so on the crystal structure and component were characterized by XPS, AES, XRD and SEM observation. The codeposits were found to be more highly corrosion resistent than that of Ni-P amorphous alloys by measuring polarization resistance and corrosion potential. The effects of codeposition conditions on the corrosion resistance were …

Determination Of Hydrogen Diffusion Coefficient In Metal Hydride Electrode With Electrochemical Impedance Spectroscopy, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Electrochemical impedance spectroscopy was employed to determine the hydrogen diffusion coefficient in MlNi _3.75Co _0.65 Mn_0.4Al_0.2 metal hydride electrode with various states of charge (SOC) at room temperature and with 50% SOC at various temperatures. It was found that hydrogen diffusion coefficient in this electrode decreases with the increase in SOC at ambient temperature, and for the electrode with 50% SOC, hydrogen diffusion coefficient increases with the increase of temperature and the activation energy for hydrogen diffusion in it is 35 kJ/mol.

Charge/Discharge Characteristics And Structural Changing Of Spherical β-Ni(Oh)2 Prepared From Different Nickel Salt, Shu-Ting Yang, Yan-Hong Yin, Hong-Jun Chen, Jun-Hua Jia, Ming-Chum Zhang, Li Ding

Journal of Electrochemistry

Spherical β-Ni(OH)₂ was prepared from different nickel salt by homogeneous complexing precipitation method. Its charge/discharge and cyclic voltammetry properties were studied. The authors found that there are many differences in the electrochemical properties of the prepared Ni(OH)₂.The specific capacity, cycling life and the discharging plateau of the material prepared from NiSO₄ were superior to those of the material prepared from Ni(NO₃)₂. The reasons of the differences were analyzed by XRD and FTIR measurements, which will become abasis for the selection of raw materials.

The Influence Of Membrane Resistance On The Electrochemical Behavior Of Gold Electrode Modified By Self-Assembled Monolayer, Xiao-Li Cui, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical behavior of gold electrode modified by hexadecanethiol self-assembled monolayer (SAM) in the solution of Fe(CN)₆^3-/Fe(CN)₆^4- was investigated by cyclic voltammetry and ac impedance spectroscopy. The pinhole-free SAM-modified gold electrode has excellent blocking properties to the interfacial electron transfer from redox couple in solution to the substrate. The current increased exponentially with the overpotential at the high potential region. A good linear relationship between ln(I/η) and η_1/2 was observed. A model system Au/SAM/Hg was constructed and its I～V curve was measured. Similar phenomena were observed. There was also a linear relationship between ln(I/V) …

The Activation Mechanism Of Al Alloys With Tin And Gallium In Alkaline Electrolytes, Zhen-Ya Li, Ling Yi, Zhi-Hui Liu, Lin Yang, Jing-Xin Su, Yan-Ying Chen

Journal of Electrochemistry

The major reason for Al-anode's activation is that Ga and Sn deposit on the aluminum surface and form activated points. The Al-Sn and Al-Ga binary alloys can't be activated in alkaline medium. During the dissolution of the Al-Sn-Ga ternary anode, Sn and Ga dissolve into the solution and transform into ions. After the Sn ions deposit on the surface of Al-anode, the Ga ions will deposit on Sn. The higher activation of the polynary alloy anode is caused by much more new activated points composed of Ga-Sn alloy being continually formed. Ga- Sn alloy with low melting point deposited on …

Analysis Of Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

The goal is to achieve a basic understanding of the corrosion of stainless steel by Lead Bismuth Eutectic (LBE), which has been proposed for use in the transmuter as both a coolant and as a sputtering target.

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823 For Transmutation Applications, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the elevated temperature tensile properties of Alloy EP- 823, a leading target material for accelerator-driven waste transmutation applications. This alloy has been proven to be an excellent structural material to contain the lead-bismuth-eutectic (LBE) nuclear coolant needed for fast spectrum operations. However, very little data exist in the open literature on the tensile properties of this alloy. The selection of Alloy EP-823 as the test material in the proposed task is based on the recommendation of our collaborator at the Los Alamos National Laboratory (LANL). The test material will be thermally treated …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The proposed work will combine chemical kinetics and hydrodynamics in target and test-loop lead-bismuth eutectic (LBE) systems to model system corrosion effects. This approach will result in a predicative tool that can be validated with corrosion test data, used to systematically design tests and interpret the results, and provide guidance for optimization in LBE system designs. The task includes of two subtasks. The first subtask is to try to develop the necessary predictive tools to be able to predict the levels of oxygen and corrosion products close to the boundary layer through the use of Computational Fluid Dynamics (CFD) modeling. …