Materials Science and Engineering Commons^™

Performance Of Co2/H2O Co-Electrolysis In A Flat-Tube Solid Oxide Electrolysis Cell Stack Under Air-Free Environment, Xiao-Hui Zhong, Fei Wang, An-Qi Wu, Bei-Bei Han, Jian-Xin Wang, Wan-Bing Guan

Journal of Electrochemistry

This work investigates the transient performance and stability of CO₂/H₂O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell (SOEC) stack. The results show that the transient behavior of the stack with and without blowing gas in the air electrode is almost the same. With a current density of 0.67 A·cm⁻²@750 °C, the stack operated for over 200 h under co-electrolysis conditions with no air blowing, and the voltage drop rate of the stack was approximately 0.203%/100 hours. Microstructure analysis reveals significant loss of Ni particles and formation of an insulating …

Variation Of Membrane Electrode Assembly Catalyst Layer In Unitized Regenerative Fuel Cell, Yollanda Nurcholifah, Dedi Rohendi, Edy Herianto Majlan, Nirwan Syarif, Addy Rachmat, Dwi Hawa Yulianti, Nyimas Febrika S

Journal of Electrochemistry

A unitized regenerative fuel cell (URFC) is a device that may function reversibly as either a fuel cell (FC) or water electrolysis (WE). An important component of this device is the Membrane electrode assembly (MEA). Therefore, this study aimed to compare the performance outcomes of MEA using electrodes with single and three catalyst layers. This study measured Electrochemical Surface Area (ECSA), Electrochemical Impedance Spectroscopy (EIS), X-ray Diffraction analysis (XRD), and X-ray Fluorescence (XRF). Furthermore, the round-trip efficiency (RTE) of the MEA, as well as the performance in FC and WE mode, was measured. In comparison, The ECSA values of Pt-Ru/C …

Mechanochemical Reaction Kinetics—A Theoretical Modeling And Experimental Study, Maria Dolores Masso Ramirez

Mechanical & Aerospace Engineering Theses & Dissertations

Mechanochemical reactions represent a class of chemical processes triggered by mechanical energy, widely recognized for their efficiency, solvent-free nature, and environmental benefits. They are increasingly applied in synthetic chemistry, a branch of science focused on creating new chemical compounds through controlled laboratory reactions. However, the mechanisms underlying mechanical activation remain poorly understood, primarily due to the difficulty in quantifying energy transfer during milling, where solid reactants are ground together using a ball mill. This thesis aims to bridge the gap in understanding the relationship between mechanical parameters and reaction kinetics by developing and validating a theoretical framework based on dimensional …

Study On Dopamine Electrochemical Sensing Based On Au@Mos2, Ning An, Ni Su, Xin-Ran Li, Jian-Yu Liu, Qi-Yan Wang

Journal of Electrochemistry

Dopamine (DA) is a vital neurotransmitter, and accurate detection of its concentration is critical for both clinical diagnostics and neuroscience research. Due to its electrochemical activity, DA is commonly detected using electrochemical methods, which are favored for their simplicity, fast response time, and suitability for in vivo analysis. In this work, a highly sensitive DA electrochemical sensor was developed using an Au@MoS₂ composite, created by modifying molybdenum disulfide (MoS₂) nanosheets with gold nanoparticles through HAuCl₄ reduction, and it was aimed at enhancing DA adsorption and improving detection performance. Scanning Electron Microscopy (SEM), transmission electron microscopy (TEM), …

Recent Advances In Non-Enzymatic Electrochemical Sensors For Theophylline Detection, Gustria Ernis, Yulia M T A Putri, Muhammad Iqbal Syauqi, Prastika Krisma Jiwanti, Yeni Wahyuni Hartati, Takeshi Kondo, Qonita Kurnia Anjani, Jarnuzi Gunlazuardi

Journal of Electrochemistry

Detection of target analytes at low concentrations is significant in various fields, including pharmaceuticals, healthcare, and environmental protection. Theophylline (TP), a natural alkaloid used as a bronchodilator to treat respiratory disorders such as asthma, bronchitis, and emphysema, has a narrow therapeutic window with a safe plasma concentration ranging from 55.5–111.0 μmol·L^–1 in adults. Accurate monitoring of TP levels is essential because too low or too high can cause serious side effects. In this regard, non-enzymatic electrochemical sensors offer a practical solution with rapidity, portability, and high sensitivity. This article aims to provide a comprehensive review of the recent developments …

Enhancing Cycle Life Of Graphite ‖ Lifepo4 Batteries Via Copper Substituted Li2Ni1-XCuXO2 Cathode Prelithiation Additive, Jian-Ming Zheng, Jing-Wen Zhang, Tian-Peng Jiao

Journal of Electrochemistry

Lithium nickel oxide (Li₂NiO₂), as a sacrificial cathode prelithiation additive, has been used to compensate for the lithium loss for improving the lifespan of lithium-ion batteries (LIBs). However, high-cost Li₂NiO₂ suffers from inferior delithiation kinetics during the first cycle. Herein, we investigate the effects of the cost-effective Cu substitution of Li₂Ni_1-xCu_xO₂ (x = 0, 0.2, 0.3, 0.5, 0.7) synthesized by high-temperature solid-phase method on the structure, morphology, electrochemical performance of graphite‖LiFePO₄ battery. The X-ray Diffraction (XRD) refinement result demonstrates that Cu substitution strategy is favorable …

Metal Nitrides As Cathode Hosts For Lithium-Sulfur Batteries, Hai-Ji Xiong, Cheng-Wei Zhu, Ding-Rong Deng, Qi-Hui Wu

Journal of Electrochemistry

Lithium-sulfur batteries are considered as one of the potential solutions as integrating renewable energy systems for large-scale energy storage because of their high theoretical energy density (2600 Wh·kg^–1) and specific capacity (1675 mAh·g^–1). Currently, various strategies have been proposed to overcome the technical barriers, e.g., “shuttle effect”, capacity decay and volumetric change, which impede the successful commercialization of lithium-sulfur batteries. This paper reviews the applications of metal nitrides as the cathode hosts for high-performance lithium-sulfur batteries, summarizes the design strategies of different host materials, and discusses the relationship between the properties of metal nitrides and their …

Sno2 Particles Embedded Into Carbon Coated Mesoporous SioX Rod As High Volumetric Capacity Anode For Lithium-Ion Batteries, Jia-Lin Guo, Ni-Ni Li, Peng Zheng

Journal of Electrochemistry

Due to the high capacity and moderate volume expansion of silicon protoxide SiO_x (160%) compared with that of Si (300%), reducing silicon dioxide SiO₂ into SiO_x while maintaining its special nano-morphology makes it attractive as an anode of Li-ion batteries. Herein, through a one-pot facile high-temperature annealing route, using SBA15 as the silicon source, and embedding tin dioxide SnO₂ particles into carbon coated SiO_x, the mesoporous SiO_x-SnO₂@C rod composite was prepared and tested as the anode material. The results revealed that the SnO₂ particles were distributed uniformly in the …

A Cnt Intercalated Co Porphyrin-Based Metal Organic Framework Catalyst For Oxygen Reduction Reaction, Pei-Pei He, Jin-Hua Shi, Xiao-Yu Li, Ming-Jie Liu, Zhou Fang, Jing He, Zhong-Jian Li, Xin-Sheng Peng, Qing-Gang He

Journal of Electrochemistry

The poor electronic conductivity of metal-organic framework (MOF) materials hinders their direct application in the field of electrocatalysis in fuel cells. Herein, we proposed a strategy of embedding carbon nanotubes (CNTs) during the growth process of MOF crystals, synthesizing a metalloporphyrin-based MOF catalyst TCPPCo-MOF-CNT with a unique CNT-intercalated MOF structure. Physical characterization revealed that the CNTs enhance the overall conductivity while retaining the original characteristics of the MOF and metalloporphyrin. Simultaneously, the insertion of CNTs generated adequate mesopores and created a hierarchical porous structure that enhances mass transfer efficiency. X-ray photoelectron spectroscopic analysis confirmed that the C atom in CNT …

New Insights Into Controlling The Functional Properties Of Tin Oxide-Based Materials, Alexandra Kuriganova, Nina Smirnova

Journal of Electrochemistry

Development of methodologies for fabrications of nanostructured materials that provide control over their microstructural features and compositions represents a fundamental step in the advancement of technologies for productions of materials with well-defined functional properties. Pulse electrolysis, a top-down electrochemical approach, has been demonstrated to be a viable method for producing nanostructured materials with a particular efficacy in the synthesis of tin oxides. This method allows for significant control over the composition and shape of the resulting tin oxides particles by modifying the anionic composition of the aqueous electrolyte, obviating the need for additional capping agents in the synthesis process and …

Nanostructured Graphitic Carbon Nitride For Photocatalytic And Electrochemical Applications, Muhammad Abdul Qadeer, Iqra Fareed, Asif Hussaine, Muhammad Asim Farid, Sadia Nazir, Faheem K. Butt, Ji-Jun Zou, Muhammad Tahir, Shang-Feng Du

Journal of Electrochemistry

Graphitic carbon nitride (g-C₃N₄) exhibits great mechanical as well as thermal characteristics, making it a valuable material for use in photoelectric conversion devices, an accelerator for synthesis of organic compounds, an electrolyte for fuel cell applications or power sources, and a hydrogen storage substance and a fluorescence detector. It is fabricated using different methods, and there is a variety of morphologies and nanostructures such as zero to three dimensions that have been designed for different purposes. There are many reports about g-C₃N₄ in recent years, but a comprehensive review which covers nanostructure dimensions …

Characterization And Optimization Of Sand And Tung Oil-Based Resins For Binder-Jet 3d Printing, Daniel I. Ajiola

College of Graduate Studies: Theses & Dissertations

Binder-jet 3D printing as a transformative technology in additive manufacturing, offers the ability to fabricate complex structures with diverse materials. This thesis investigates the use of a sustainable tung oil-based resin to create composites, exploring the potential for an eco-friendly alternative to synthetic binders.

The aim of this research is to develop and characterize a bio-based resin formulation, using tung oil as the primary binder, for application in binder-jet 3D printing with sand as the reinforcement. The resin formulation was prepared by combining tung oil, n-butyl methacrylate, divinylbenzene, and di-tert-butyl peroxide in precise proportions, ensuring a balanced mixture that supports …

Dendrite-Free Strategies For Aqueous Zinc-Ion Batteries: Structure, Electrolyte, And Separator, Gang Wu, Wu-Hai Yang, Yang Yang, Hui-Jun Yang

Journal of Electrochemistry

Continued growth in energy demand and increased environmental pollution constitute major challenges that need to be addressed urgently. The development and utilization of renewable, sustainable, and clean energy sources, such as wind and solar, are crucial. However, the instability of these intermittent energy sources makes the need for energy storage systems increasingly urgent. Aqueous zinc-ion batteries (AZIBs) have received widespread attention due to their unique advantages, such as high energy density, cost-effectiveness, environmental friendliness, and safety. However, AZIBs face significant challenges, mainly the formation of zinc dendrites that seriously affect the stability and lifetime of the batteries, leading to battery …

Electrochemical-Method-Induced Strong Metal-Support Interaction In Pt-Cnt@Sno2 For Co-Tolerant Hydrogen Oxidation Reaction, Shen-Zhou Li, Zi-Jie Lin, Qi-An Chen, Zhao Cai, Qing Li

Journal of Electrochemistry

Inducing the classic strong metal-support interaction (SMSI) is an effective approach to enhance the performance of supported metal catalysts by encapsulating the metal nanoparticles (NPs) with supports. Conventional thermal reduction method for inducing SMSI processes is often accompanied by undesirable structural evolution of metal NPs. In this study, a mild electrochemical method has been developed as a new approach to induce SMSI, using the cable structured core@shell CNT@SnO₂ loaded Pt NPs as a proof of concept. The induced SnO_x encapsulation layer on the surface of Pt NPs can protect Pt NPs from the poisoned of CO impurity in …

Contributions To Journal Of Electrochemistry, The Flagship Journal Of Chinese Chemical Society Electrochemical Committee, Will Be Listed As A New Recommendation Policy For China Youth Awards Of Electrochemist, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

All-Solid-State Sodium-Ion Batteries: A Leading Contender In The Next-Generation Battery Race, Rui-Jie Zhu, Ze-Chen Li, Wei Zhang, Akira Nasu, Hiroaki Kobayashi, Masaki Matsui

Journal of Electrochemistry

All-solid-state lithium-ion batteries (LIBs) using ceramic electrolytes are considered the ideal form of rechargeable batteries due to their high energy density and safety. However, in the pursuit of all-solid-state LIBs, the issue of lithium resource availability is selectively overlooked. Considering that the amount of lithium required for all-solid-state LIBs is not sustainable with current lithium resources, another system that also offers the dual advantages of high energy density and safety— all-solid-state sodium-ion batteries (SIBs) —holds significant sustainable advantages and is likely to be the strong contender in the competition for developing next-generation high-energy-density batteries. This article briefly introduces the research …

Aqueous Supercapacitors With Wide Operative Voltage Window And Long Cycling Life Enabled By Electrolyte Hybridization Effect, Shi-Hua Ma, Qi Yin, Jin-Ping Zhao

Journal of Electrochemistry

Developing supercapacitors (SCs) with long cycling life and wide operative voltage window is a significant topic in the field of aqueous electrolytes. Although the design of water in salt (WIS) electrolytes has pushed the development of aqueous electrolytes to a new height, the WIS electrolytes with an operative voltage window of up to 2.5 V is still very scarce. Herein, in order to enrich the type of aqueous electrolyte with high operative voltage, tetramethylammonium trifluoromethanesulfonate (TMAOTf) based WIS electrolyte was used as a model to construct WIS based hybrid electrolyte with acetonitrile (ACN) co-solvent and LiTFSI co-solute. In view of …

Journal Of Electrochemistry, The Flagship Journal Of Chinese Chemical Society Electrochemical Committee, Made A Public Appearance At The 22nd National Electrochemical Congress, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

The Award Ceremony Of The 2nd Xiamen University Short Video Abstract Contest For Science And Technology Journal Papers Came To A Successful Conclusion, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

The 9th National Conference Of Solid State Battery Successfully Held In Xiamen, Fujian, Zheng-Liang Gong

Journal of Electrochemistry

No abstract provided.

Highly Sensitive Detection Of Strontium Ions Using Metal-Organic Frameworks Functionalized Solid-State Nanochannels, Xu-Gang Wang, Zheng-Xu He, De-Fang Ding, Xue-Qin Luo, Li Dai, Wei-Qi Zhang, Qun Ma, Yu Huang, Fan Xia

Journal of Electrochemistry

Strontium-90, a highly radioactive isotope, accumulates within the food chain and skeletal structure, posing significant risks to human health. There is a critical need for a sensitive detection strategy for Strontium-90 in complex environmental samples. Here, solid-state nanochannels, modified with metal-organic frameworks (MOF) and specific aptamers, were engineered for highly sensitive detection of strontium ion (Sr²⁺). The synergistic effect between the reduced effective diameter of the nanochannels due to MOF and the specific binding of Sr²⁺ by aptamers amplifies the difference in ionic current signals, enhancing detection sensitivity significantly. The MOF-modified nanochannels exhibit highly sensitive detection of …

Journal Of Electrochemistry Is Selected To Entering Ici Journals Master List, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Goodbye With Tears! Deep Condolences To Academician Zhao-Wu Tian!, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

The Adviser Of Journal Of Electrochemistry Professor Christian Amatore Received The Chinese Government Friendship Award, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Substrate Interference And Strain In The Second-Harmonic Generation From Mose2 Monolayers, Sudeep Puri, Sneha Patel, Jose Luis Cabellos, Luis Enrique Rosas-Hernandez, Kaitlin Reynolds, Hugh O.H. Churchill, Salvador Barraza-Lopez, Bernardo S. Mendoza, Hiroyuki Nakamura

Physics Faculty Publications and Presentations

Nonlinear optical materials of atomic thickness, such as non-centrosymmetric 2H transition metal dichalcogenide monolayers, have a second-order nonlinear susceptibility (χ⁽²⁾) whose intensity can be tuned by strain. However, whether χ⁽²⁾ is enhanced or reduced by tensile strain is a subject of conflicting reports. Here, we grow high-quality MoSe₂ monolayers under controlled biaxial strain created by two different substrates and study their linear and nonlinear optical responses with a combination of experimental and theoretical approaches. Up to a 15-fold overall enhancement in second-harmonic generation (SHG) intensity is observed from MoSe₂ monolayers grown on SiO₂ when …

Zhong-Qun Tian, Academician And Honorary Member Of Electrochemistry Committee Chinese Chemical Society, Achieved "Raman Lifetime Award", Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

2024 Tianmulake Advanced Anode Materials Innovation Forum And Sixth National Conference Of Advanced Battery Failure Analysis And Testing Technology Concluded Successfully, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Optimization Of Channel Structure Of Alkaline Water Electrolyzer By Using An Expanded Mesh As A Bipolar Plate, Hai-Yan Xiong, Zhen-Xiao Zhu, Xin Gao, Chen-Ming Fan, Hui-Bao Luan, Bing Li

Journal of Electrochemistry

Alkaline water electrolysis (AWE) is the most mature technology for hydrogen production by water electrolysis. Alkaline water electrolyzer consists of multiple electrolysis cells, and a single cell consists of a diaphragm, electrodes, bipolar plates and end plates, etc. The existing industrial bipolar plate channel is concave-convex structure, which is manufactured by complicated and high-cost mold punching. This structure still results in uneven electrolyte flow and low current density in the electrolytic cell, further increasing in energy consumption and cost of AWE. Thereby, in this article, the electrochemical and flow model is firstly constructed, based on the existing industrial concave and …

Chinese Chemical Society: First Young Scholars' Symposium On Electrosynthesis Held Successfully, Chinese Society Of Electrochemistry (Cse)

Journal of Electrochemistry

No abstract provided.

Electronic Communication Between Co And Ru Sites Decorated On Nitrogen-Doped Carbon Nanotubes Boost The Alkaline Hydrogen Evolution Reaction, Meng-Ting Gao, Ying Wei, Xue-Meng Hu, Wenj-Jie Zhu, Qing-Qing Liu, Jin-Yuan Qiang, Wan-Wan Liu, Ying Wang, Xu Li, Jian-Feng Huang, Yong-Qiang Feng

Journal of Electrochemistry

Designing highly efficient Pt-free electrocatalysts with low overpotential for an alkaline hydrogen evolution reaction (HER) remains a significant challenge. Here, a novel and efficient cobalt (Co), ruthenium (Ru) bimetallic electrocatalyst composed of CoRu nanoalloy decorated on the N-doped carbon nanotubes (CoRu@N-CNTs), was prepared by reacting fullerenol with melamine via hydrothermal treatment and followed by pyrolysis. Benefiting from the electronic communication between Co and Ru sites, the as-obtained CoRu@N-CNTs catalyst exhibited superior electrocatalytic HER activity. To deliver a current density of 10 mA·cm^–2, it required an overpotential of merely 19 mV along with a Tafel slope of 26.19 mV·dec …