Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Physical Chemistry

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 1651 - 1680 of 1912

Full-Text Articles in Materials Science and Engineering

Sprayed And Thermally Evaporated Carbon Films As Anodes For Lithium Ion Batteries, Shu-Gao Zhang, M.Schleich Donald Feb 2000

Sprayed And Thermally Evaporated Carbon Films As Anodes For Lithium Ion Batteries, Shu-Gao Zhang, M.Schleich Donald

Journal of Electrochemistry

Carbon films were made using spray-thermal evaporation from a kind of pyrolytic carbon powder. The films obtained with graphite structure were both potentio-statically and galvanostaically tested. Cycling patterns indicated a reduction peak on the first cycle corresponding to the formation of solid electrolyte interface, and the capacity values and x values were quite acceptable compared to theoretical ones when charging-discharging current density was suitable. Based on the experimental results, the obtained carbon films could be used as anode materials for relatively determining the electrochemical performances of cathode materials.

Go to article

Studies Of The Preparation Of Electrodes From Lead Carbonate For Lead-Acid Battery Ⅱ. The Preparation Of Paste Electrodes, Zhong-Xu Dai, Di-Hua Wang, Hao-Hao Ke, Jin-Yun Zou, Yun-Hong Zhou Feb 2000

Studies Of The Preparation Of Electrodes From Lead Carbonate For Lead-Acid Battery Ⅱ. The Preparation Of Paste Electrodes, Zhong-Xu Dai, Di-Hua Wang, Hao-Hao Ke, Jin-Yun Zou, Yun-Hong Zhou

Journal of Electrochemistry

The positive and negative pastes were prepared by mixing PbCO3 and H2SO4 solution as well as relative additives, respectively. The effects of the various formation methods and the charge/discharge conditions on discharge capacity and active material utilization of both electrodes were examined. The results indicate that the performance of the positive electrode formed at 2.0 mA/cm2 is better than that formed at higher current density under the same charge/discharge condition, the PAM utilization reaches 74.4 % under discharging at 2.0 mA/cm2; and the property of the negative electrode formed by unsymmetrical square wave …

Go to article

Inhibition Of N,N'-O-Phenylen-Bis(3-Methoxysalicylidenimine) On Copper In Halide Solutions, Hou-Yi Ma, Shen-Hao Chen, Zhen-Lan Quan, Lin Niu, Shu-Lan Li Feb 2000

Inhibition Of N,N'-O-Phenylen-Bis(3-Methoxysalicylidenimine) On Copper In Halide Solutions, Hou-Yi Ma, Shen-Hao Chen, Zhen-Lan Quan, Lin Niu, Shu-Lan Li

Journal of Electrochemistry

Inhibition of N,N'-o-phenylen-bis(3-methoxysalicylidenimine) (V-o-Ph-V) on corrosion and anodic disslution of copper in neutral NaCl and NaBr solutions was investigated in terms of potentiostatic steady-state polarization and A.C. impedance techniques. The inhibition mechanism of V-o-Ph-V to copper corrosion was interpreted in detail by comparing the electrochemical behaviors of copper in halide solutions with or without V-o-Ph-V. Besides, the inhibition effect of self-assembled V-o-Ph-V film on copper corrosion in NaCl was also studied.

Go to article

An Eis Study On The Synergetic Filming Between Cathodic Protection And The Corrosion Inhibitor, Yong-Tao Zhao, Jian-Hua Wu, Jian-Hua Qian, Hui Yu Feb 2000

An Eis Study On The Synergetic Filming Between Cathodic Protection And The Corrosion Inhibitor, Yong-Tao Zhao, Jian-Hua Wu, Jian-Hua Qian, Hui Yu

Journal of Electrochemistry

The electrochemical impedance spectroscope (EIS) of 907A steel in seawater was investigated to study the film formation and destruction. The corrosion protection mechanism of the synergy interaction between cathodic protection and YKI-5 corrosion inhibitor (a mixture of polyhydric alcohol phosphate ester, phosphate and polyphosphate) is discused. Typical EIS spectral changes were clearly observed during the film formation and destruction processes. EIS results indicated that the film seemed to formed a multi-layered structure which consist of an inner layer (this may be an inhibitor-metal complex layer) and many outer layers of calcareous deposits. The film possesses of good persistency under the …

Go to article

In-Situ Simultaneous Esr And Conductivity Measurements For Polyaniline, Lin Zhuang, Qing Zhou, Jun-Tao Lu Feb 2000

In-Situ Simultaneous Esr And Conductivity Measurements For Polyaniline, Lin Zhuang, Qing Zhou, Jun-Tao Lu

Journal of Electrochemistry

With a new cell design, simultaneous electrochemical ESR and conductance measurements were realized for the first time. The in-situ cell consisted of a dual working electrode, a counter electrode and a reference electrode accommodated in a capillary of 1mm diameter. The dual working electrode was composed of two closely spaced Pt electrodes: a Pt disk electrode (0.5 mm diameter) sealed in a thin glass tube and a Pt layer deposited on the outside wall of the glass tube. The two working electrodes were separated by the glass gap about 20 μm thick. Two potentiostats were used to control electrode potential …

Go to article

Study On Preparation Of Coarse And Fine γ-Lialo2 Mixed Powder Used For Mcfc Matrix, Hua-Xin Lin, Bao-Lian Yi, Lian-Ying Kong, En-Jun Zhang, Li Zhou, Feng-Xia Wang Feb 2000

Study On Preparation Of Coarse And Fine γ-Lialo2 Mixed Powder Used For Mcfc Matrix, Hua-Xin Lin, Bao-Lian Yi, Lian-Ying Kong, En-Jun Zhang, Li Zhou, Feng-Xia Wang

Journal of Electrochemistry

Coarse α-LiALO2 powder was transferred completely to γ-LiAlO2 at 900 ℃ for ten hours. Fine γ-LiALO2 powder was prepared by “chloride” synthesis. MCFC matrix was fabricated by mixing the coarse and fine γ-LiALO2 powder and by tape cast. The out'put voltage of the cell assembled with the matrix was 0.85 and 0.75 V respectively at 200 and 300 mA/cm 2, and power density was about 250 mW/cm2. The performance of the matrix fabricated with the mixed powder was obviously more advanced than that of the matrix fabricated with only coarse γ-LiALO2 powder.

Go to article

Effect Of Different Species Of Cobalt Additive On Performance Of Nickel Hydroxide Electrode, Xian-Xia Yuan, Yin-Dong Wang, Feng Zhan Feb 2000

Effect Of Different Species Of Cobalt Additive On Performance Of Nickel Hydroxide Electrode, Xian-Xia Yuan, Yin-Dong Wang, Feng Zhan

Journal of Electrochemistry

Performances of nickel electrodes when adding or without adding Cobalt in different forms were studied, the results were interpreted by cyclic voltammetry(CV) and electrochemical impedance spectroscope (EIS). It was demonstrated that the additions of Co, CoO, CoO+Co by mechanically mixing with Ni(OH)2 all can improve the performance of nickel electrode to some extent, and when Co is added in the form of CoO the best performance can be obtained. This can be mainly attributed to the fact that three kinds of Co additives all improved the structure of nickel hydroxide and the ability of H+ in electrolyte transporting …

Go to article

Fabrication And Examination Of Reduced Temperatrue Solid Oxide Fuel Cell Using A Supported Thin Ysz Electrolyte Substrate, Yi-Huang Zhang, Yong-Lei Dong, Yi Jiang, Zhi-Gui Lu, Jing-Wang Yan Feb 2000

Fabrication And Examination Of Reduced Temperatrue Solid Oxide Fuel Cell Using A Supported Thin Ysz Electrolyte Substrate, Yi-Huang Zhang, Yong-Lei Dong, Yi Jiang, Zhi-Gui Lu, Jing-Wang Yan

Journal of Electrochemistry

By using a cost-effective wet process,dense yttria stabilized zirconia (YSZ) films on Ni-YSZ anode substrates have been prepared successfully. The YSZ film was characterized to be around 10 μm in thickness, sufficiently dense, uniform and crack free. A single solid oxide fuel cell fabricated from the supported YSZ film electrolyte on the anode substrate and a LSM cathode prepared on the YSZ film was tested. The power density reached to 0.1 W/cm2 at 800 ℃, showing a reasonable performance. Further analysis on both electrodes shows that the anodic overpotential was much larger than IR drop (including YSZ resistance and …

Go to article

Cathodic Indirect Electro-Oxidation——Organic Electro-Synthesis Dimethyl Sulfone, Deng-Ping Gu, Rui-Zhi Wang, Hong-Kun Zhang, Xue-Ying Zhang, Wei Li, Bao-Qiu Cui Feb 2000

Cathodic Indirect Electro-Oxidation——Organic Electro-Synthesis Dimethyl Sulfone, Deng-Ping Gu, Rui-Zhi Wang, Hong-Kun Zhang, Xue-Ying Zhang, Wei Li, Bao-Qiu Cui

Journal of Electrochemistry

A cathodic indirect electro-oxidation system was established for indirect electro-oxidize dimethyl sulfoxide to dimethyl sulfone with electro-eduction generated H2O2 catalyzed by the pertungstate/tungstate (WO52-/WO42-) redox mediator. Influences of current density, pH, temperature, and the current efficiencies etc. On the cathodic indirect electro-oxidation of dimethyl sulfone were investigated for determining optimum reaction conditions. The current efficiency reached more than 70%. Mother-liquid could be recycled to use without pollution.

Go to article

Electrodeposition Of Copper On Polished Copper Electrode, Jia Tsung Ling Jan 2000

Electrodeposition Of Copper On Polished Copper Electrode, Jia Tsung Ling

Student Works (2000-2009)

This project studies the surface morphology of the copper deposit from three different bath solutions on polished copper (3.1 mm in diameter) electrode by using Scanning Electron Microscopy. The behaviour of glycine as an additive in a bath solution containing 0.3 M of copper (II) sulphate and 2.2 M of sulphuric acid was studied by using cyclic voltammetry. In this project, glycine did not involved directly in the reaction of CU²⁺/CU couple but increased the potential and current density of the plating process. However, glycine has the properties for inhibiting the deposition of copper onto the copper disc. Moreover, block …

Go to article

Studies On Methods Of Fuel Cells Electrodes Preparation, Jun Gu, Sheng Sui, Guang-Qiang Li, Zhitong Sui Nov 1999

Studies On Methods Of Fuel Cells Electrodes Preparation, Jun Gu, Sheng Sui, Guang-Qiang Li, Zhitong Sui

Journal of Electrochemistry

In fuel cells, the structure of electrodes is an important factor which effect the cell performance. To improve the structure and the performance of electrodes, a new method of providing fuel cell electrodes is proposed in this paper. PTFE (polytetrafluoroethylene) and ethyne black was ground for about half an hour in a high-speed grinder, then the catalyst was added into the grinder and milled for an hour. This milled catalyst was transferred into a mixer followed by the addition of surface-active agent. After a suspension was formed, it was filtered under vacuum condition.Then a thin uniform filter-cake of the catalyst …

Go to article

A Novel Reaction Region Moving Electrode System For Electrochemical Power Sources, Jin-Kua You, Que Tu, Zheng-Jian Wang, Jie Sun, Zu-Geng Lin Nov 1999

A Novel Reaction Region Moving Electrode System For Electrochemical Power Sources, Jin-Kua You, Que Tu, Zheng-Jian Wang, Jie Sun, Zu-Geng Lin

Journal of Electrochemistry

In most of practical rechargeable batteries, charging/discharging process is always concerned with phase-transformation in the solid state. Due to the irreversibility of the phase-transformation, the cyclic performance of the rechargeable batteries are limited. In this paper, a novel reaction-region moving counter electrode system is constructed in our laboratory. The electrode system is operated at room temperature and cycled in solid-liquid phase during charging/discharging processes. With this electrode, the metal-complexes are firstly deposited (i.e. charging process) on the nearest working electrode and gradually extended to those another working electrodes several centimeters away from the counter electrode. The deposite is dissolved again …

Go to article

Study On Electrochemical Reduction Properties Of Nitrobenzene, Chu-Na Ma, Wen-Kui Zhang, Hui Huang, Yong-Ping Gan Nov 1999

Study On Electrochemical Reduction Properties Of Nitrobenzene, Chu-Na Ma, Wen-Kui Zhang, Hui Huang, Yong-Ping Gan

Journal of Electrochemistry

The electrochemical reduction characteristics of nitrobenzene was extensively investigated by using the techniques such as quasi-steady-state polarization, cyclic voltammetry, fast linear potential sweep method and chronoamperometry in this paper. The electroanalytic properties of Cu, Cu-Hg and Cu-Ni electrodes were evaluated. Based on the study of the transient steping behaviour of nitrobenzene to PAP, the reduction mechanism was discussed. The results showed that the transition steps existed on the electrochemical reduction of nitrobenzene in acidic solution, the reactant is also absorbed on electrodes surface. The control step in the reduction of nitrobenzene was ascribed to the diffusion of nitrobenzene and its …

Go to article

High Performance Proton Exchange Membrane Fuel Cells, Jing-Rong Yu, Bao-Lian Yi, Ming Han, Xiao-Liang Cheng, Zhi-Gang Shao, Jing-Xin Zhang Nov 1999

High Performance Proton Exchange Membrane Fuel Cells, Jing-Rong Yu, Bao-Lian Yi, Ming Han, Xiao-Liang Cheng, Zhi-Gang Shao, Jing-Xin Zhang

Journal of Electrochemistry

Proton-exchange membrane fuel cells(PEMFC) using a perfluorosulfonic acid proton exchange membrane as an electrolyte can simplify water and electrolyte management. In this paper, the effects of thickness of PEM on the performance of PEMFC were studied. The Nafion-112 PEM and low platinum loading E-TEK electrode yielded very high power density, of the order of 0.95 W/cm2. The energy-conversion efficiency, the degree of platinum utilization and stability for PEMFC using Nafion 112 and E-TEK electrode were also investigated.

Go to article

Photoelectrochemical Studies On The Tio2 Nanostructured Porous Film Sensitized By Cyanine Dye, Li Zhang, Mai-Zhi Yang, Xue-Bin Qiao, Yan-Zhong Hao, En-Qing Gao, Sheng-Min Cai Nov 1999

Photoelectrochemical Studies On The Tio2 Nanostructured Porous Film Sensitized By Cyanine Dye, Li Zhang, Mai-Zhi Yang, Xue-Bin Qiao, Yan-Zhong Hao, En-Qing Gao, Sheng-Min Cai

Journal of Electrochemistry

The photoelectrochemical behaviors of the TiO2 nanostructured porous film sensitized by cyanine dye were investigated in this paper. The results showed that the excitaed state level matched the conduction band edge of TiO2 nanoparticle. Therefore the sensitization of the dye can increase the photocurrent intensity of the TiO2 nanostructured electrode obviously and results in a red-shift of optical absorption from the ultra-violet region to the visible. As a result, the light-to-electricity conversion efficiency was improved evidently, the maximum value of IPCE has reached 12.1%.

Go to article

Investigation Of Sodium Hypophosphite Anodic Oxidizing Behavior In The Process Of Acid Electroless Nickel Deposition, Mei-Yuan Wang, Ya-Fei Kuang, Yan Xu Nov 1999

Investigation Of Sodium Hypophosphite Anodic Oxidizing Behavior In The Process Of Acid Electroless Nickel Deposition, Mei-Yuan Wang, Ya-Fei Kuang, Yan Xu

Journal of Electrochemistry

The anodic oxidizing behavior of sodium hypophosphite in the process of electroless nickle deposition (pH=5.5) was investigated with the linear potential sweep method and alternating current impedance. The results indicated that, the oxidation of NaH2PO2 was a complicated electrochemical process and affected by the concentration of NaH2PO2, the temperature of the bath, the sweep rate and the existence of nickel ion. The NaH2PO2 electrooxidation reaction was very likely preceded by heterogeneous interface transformation process, which might be the control step of the whole anodic process.

Go to article

The Preparation Of Flexible Polymeric Anode And The Measurement Of Its Protective Ability For Cathodic Protection, Ai-Ling Du, He-Ming Zhang, Ming-Zong Zhang, Shi-De Ma Nov 1999

The Preparation Of Flexible Polymeric Anode And The Measurement Of Its Protective Ability For Cathodic Protection, Ai-Ling Du, He-Ming Zhang, Ming-Zong Zhang, Shi-De Ma

Journal of Electrochemistry

The flexible electrode, whose shape can be changed freely, was made of ethenyl copolymer and conductive component and proper amount of additive for cathodic protection. The resistance of electrode was measured.In low concentration of H2SO4, the flexible electrode can be used as auxiliary anode to protect the carbon steel. The protection ability of the flexible auxiliary anode was measured too.

Go to article

Studies Of The Electrode Preparation Of Electrode From Lead Carbonate For Lead Acid Batteryⅰ. The Activation Of The Pme, Zhong-Xu Dai, Di-Hua Wang, Jun-Wei Jiang, Yun-Hong Zhou, Jin-Yun Zou Nov 1999

Studies Of The Electrode Preparation Of Electrode From Lead Carbonate For Lead Acid Batteryⅰ. The Activation Of The Pme, Zhong-Xu Dai, Di-Hua Wang, Jun-Wei Jiang, Yun-Hong Zhou, Jin-Yun Zou

Journal of Electrochemistry

Lead carbonate which was an intermediate product in lead hydrometallurgy without pollution of lead vapor and sulfur dioxide was selected as electrode material of lead-acid batteries. In the present work, the performances of PbO2/PbSO4 or PbSO4/Pb electrode transformed from PbCO3 have been investigated by powder microelectrode technique combined with cyclic voltammetry. The results show that the CV characteristics of either negative or positive electrode prepared from PbCO3 is as good as that of both electrodes made from lead oxide produced by mill machine,when a powder microelectrode with PbCO3 transformed into PbSO 4 …

Go to article

The Studies Of The (Photo) Electrochemical Character On The Electrodeposited Silver Indium Selenium Thin Films, Shao-Ai Xie, Xun-Nan Deng, You-Jin Kua Nov 1999

The Studies Of The (Photo) Electrochemical Character On The Electrodeposited Silver Indium Selenium Thin Films, Shao-Ai Xie, Xun-Nan Deng, You-Jin Kua

Journal of Electrochemistry

A photoelectrochemical cell (PEC) is constructed, using an AgInSe2 film photoanode made from electrodeposition and a platinium electrode in aqueous polyiodide or polysufide electrolyte. The Voc and Isc of PEC have been tested and measured, and the effect of chemical decoration on the photoanodes also studied.

Go to article

The Electrochemical Behaviors Of Superoxide Dismutase At Promoter Modified Gold Electrode, Xia-Qin Wu, Xiao-Yun Meng, Zhe-Su Wang, Zong-Rang Zhang Nov 1999

The Electrochemical Behaviors Of Superoxide Dismutase At Promoter Modified Gold Electrode, Xia-Qin Wu, Xiao-Yun Meng, Zhe-Su Wang, Zong-Rang Zhang

Journal of Electrochemistry

The electron-transfer process of superoxide dismutase was investigated by cyclic voltammetry at the 4,4'-dithiodipyridine, L-cysteine, histidine and arginine modified gold wire electrodes repectively. The quasi-reversible behavior was observed at L-cysteine modified gold electrode. An irreversible electrochemical behavior has been observed at hisdinine modified gold wire electrode.

Go to article

Electro-Oxidation Of Phenol On Sno2/Ti Electrodes Prepared By Thermal Oxidation, Qing-Song Zhang, Hui-Huang Wu Nov 1999

Electro-Oxidation Of Phenol On Sno2/Ti Electrodes Prepared By Thermal Oxidation, Qing-Song Zhang, Hui-Huang Wu

Journal of Electrochemistry

A SnO2/Ti electrode prepared by thermal oxidation was used as the anode for galvanostatic electrolysis in acidic solution containing phenol, the time-dependances of phenol concentration, chemical oxygen demand in solution(COD) and instantaneous current efficiency were determined during electrolysis. The results show that with the SnO2/Ti anode instead of Pt, the COD significantly decreases at the same charge passage, and average current efficiency of oxidation increases by three times. The mechanism for phenol oxidation at two electrodes was discussed.

Go to article

Structural And Electrochemical Studies On Lithium Manganese Oxide Containing Li+ Prepared By Hydrothermal Method For Lithium Ion Batteries, De-Yao Liu, Jin-Kua You, Wei Chu, Yong Yang, Zu-Geng Lin Aug 1999

Structural And Electrochemical Studies On Lithium Manganese Oxide Containing Li+ Prepared By Hydrothermal Method For Lithium Ion Batteries, De-Yao Liu, Jin-Kua You, Wei Chu, Yong Yang, Zu-Geng Lin

Journal of Electrochemistry

In this paper, Todorokite manganese oxides containing Li+ with large tunnel structure (sample M5) have been synthesized by hydrothermal methods from natural manganese oxide nano fiber (sample M4). The structure and composition of the samples were characterized and analyzed by XRD, ICP, TGA and DTA. Its electrochemical behavior as a cathode materials for rechargeable lithium ion insertion were studied by galvanostatic charge/discharge measurements. XRD results show that the sample M4 is mainly composed of Birnessite and Vernadite structure. Although the sample M4 shows a high initial capacity of approximately 150 mAh/g, its performances decrease gradually over 30 cycles. It …

Go to article

Deactivation Of Nickel Oxide/Hydroxide To Electrooxidation Of H2Po2 Anions On Nickel Electrodes In Alkaline Solutions, Tai-Xiang Jiang, Hui-Huang Wu Aug 1999

Deactivation Of Nickel Oxide/Hydroxide To Electrooxidation Of H2Po2 Anions On Nickel Electrodes In Alkaline Solutions, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

Electrooxidation of hypophosphite anions on polycrystalline nickel in alkaline solutions has been investigated by cyclic voltammetry and open circuit potential measurements. The results are explained based on the mechanism that the first step of hypophosphite oxidation is the adsorption of hypophosphite ions on nickel, followed by the homolysis of its hydrogen bond with the formation of radicals. The oxidation of hypophosphite on nickel in alkaline medium occurs at lower potentials between ca. -0.8 V— -1.1 V (SCE) and phosphite ion is the only oxidation product. There is no indication of hypophosphite oxidation at higher potentials. Severe deactivation of the surface …

Go to article

Calculation Of Corrosion Rate Of Passive Metals With Charge Curve Analysis Technique, Yuan-Sheng Zhang, Min Gong Aug 1999

Calculation Of Corrosion Rate Of Passive Metals With Charge Curve Analysis Technique, Yuan-Sheng Zhang, Min Gong

Journal of Electrochemistry

This work contains two parts: (1) A charge curve equation having no appro-ximation for passivated metal corrosion systems is derived and compared with the routine charge curve equation, which is virtual only when the polarization is minim(linear range). (2) It is simpler to analyze charge curve data by from of charge differential equation than from charge curve equation. After the charge curve data are measured, the slope of charge curve is computed by numerical differentiation method, then the charge differential equation may be transformed to a set of linear equations using polynomial approximation. The electrochemical parameters of corrosion system would …

Go to article

Direct Electrolysis Of Seawater On Conducting Film For Microbial Anticorrosion 1. Simulation And Measurement Technique, Wei-Ling Hu, Ling-Ling Wu, Jing Zhou, Jing-Xin Li, Jin Luo, Zhong-Hua Lin Aug 1999

Direct Electrolysis Of Seawater On Conducting Film For Microbial Anticorrosion 1. Simulation And Measurement Technique, Wei-Ling Hu, Ling-Ling Wu, Jing Zhou, Jing-Xin Li, Jin Luo, Zhong-Hua Lin

Journal of Electrochemistry

Based on the electrochemical micro probe and the weak signal detection technique, simulated test and measurement system were set up by the use of four-electrode cell(including a micro electrode), bipotentiostat, lock-in amplifier and three-dimensional micro manipulating device. Based on the system, the micrometer scale concentration distribution of trace hypochlorite, which is produced by direct electrolysis of seawater on the conducting film for preventing microbial corrosion has been obtained for the first time. Both relationships between concentration of hypochlorite and its reduction current, which is termed an working curve, and between the reduction current of hypochlorite and measured time are reported.

Go to article

The Techniques Of The Paired Electrosynthesis, Hong-Kun Zhang, Deng-Ping Gu Aug 1999

The Techniques Of The Paired Electrosynthesis, Hong-Kun Zhang, Deng-Ping Gu

Journal of Electrochemistry

In this Paper, we introduce our work on paired electrosynthesis. In conjunction with our research practice, we introduce electrolytic conditions,such as material of electrode ,courrent density and electrolytic temperature etc,as reference for researcher. We categorize the paired electrosynthesis techniques to widen our view on the paired electroorganic synthesis and to promote the deveopments of paired electrosynthesis techniques.

Go to article

A Study Of The Corrosion On Bronze, Hong-Fan Zhu, Hao Zhou Aug 1999

A Study Of The Corrosion On Bronze, Hong-Fan Zhu, Hao Zhou

Journal of Electrochemistry

The bronze is the treasure in chinese metallic antique, which was typified by product in Shang-Zhou period (three thousands years ago). Because of corrosion, archaeological messages, such as inscription and pattern on the surface of bronze, would be damaged then the value of bronze antique decreased. The bronze disease is a common disease which forms powdery rust on the surface of bronze in atmospheric environment, the powdery rust emerge from under incrusted rust, then spreads, and eventually leads to bronze damaged. This paper investigates the bronze disease. According to the chemical and electrochemical tests in simulated occluded cell, the variation …

Go to article

A Study Self-Passivation Of Passivie Film Of Stainless Steel In Vinylon Aldehyde Solution, Si-Fu Hu, Chuan-Bi Xu, Zhu-Qiu Cheng Aug 1999

A Study Self-Passivation Of Passivie Film Of Stainless Steel In Vinylon Aldehyde Solution, Si-Fu Hu, Chuan-Bi Xu, Zhu-Qiu Cheng

Journal of Electrochemistry

Properties of self-passivation for the anodic passive film of 1Cr18Ni9Ti and the firsthand passive film of SUS 36 stainless steel in vinylon aldehyde solution(H2SO4(240 g/L)+Na2SO4(70 g/L)+HCHO(25 g/L)+[Fe3+](35.4 mg/L)+[Cl-](240 mg/L) at 70 ℃ were studied by galvanostatic and potentiostatic polarization mesurements. The effects of compponents of vinylon aldehyde solution, i.e. Fe3+ and Cl-, on the passivation behaviours of stainless steel have also been investigated. The experimental results showed there is a conversion zone of the active/passive state if the area ratio of active/passive state on these …

Go to article

Influence Of Thiourea And Its Derivate On The Process Of Cathodic Electrodeposition Of Copper, Yun-Hui Dong, Ai-Hong Zou, Yun-Xia Zhao Aug 1999

Influence Of Thiourea And Its Derivate On The Process Of Cathodic Electrodeposition Of Copper, Yun-Hui Dong, Ai-Hong Zou, Yun-Xia Zhao

Journal of Electrochemistry

The effects of thiourea and its derivate on the electrodeposition of copper from the dilute acid sulphate solutions have been studied by using potential sweep techniques at quasisteady state. Limiting current densities (Id), exchange current densities (i0) and αn are obtained by data processing with the least square method. Thiourea has a depolarizing effect on the copper depositing at concentrations below 8 mg·L-1, and a polarizing effect at higher concentration (>10 mg·L-1), and it changes the mechanism of copper deposition reaction. Propenyltiourea and Phenylthiourea have a depolarizing effect on the …

Go to article

The Effects Of Metallic Cobalt Abbition On The Performance Of Pasted Nickel Electrodes, An-Bao Yuan, Jian-Qing Zhang, Wan-Chun Ding, Shao-An Cheng, Chu-Nan Cao Aug 1999

The Effects Of Metallic Cobalt Abbition On The Performance Of Pasted Nickel Electrodes, An-Bao Yuan, Jian-Qing Zhang, Wan-Chun Ding, Shao-An Cheng, Chu-Nan Cao

Journal of Electrochemistry

The Ni-foam pasted nickel electrodes prepared by coprecipitated Ni1-XZnX(OH)2 with and without cobalt power addition have been studied. The electrode with addition of metallic cobalt showed a higher performance both in discharge capacity and cycle life. It is known from the experiment results that the addition of Co can remarkably increase the active material utilization which is suggested to be improvement of discharge depth due to the conducting CoOOH formed in the first activation charging. The superior capacity during cycling could be attributed to the synergistic action of zinc and cobalt addition ,especially to the …

Go to article

First Prev Next Last