Materials Science and Engineering Commons^™

Fused Filament Fabrication Additive Manufacturing Of 17-4 Ph Stainless Steel: Process–Structure–Property Relationships In Magnetic Materials, Maanav Patel

Theses and Dissertations

Additive manufacturing (AM) enables the fabrication of complex metallic components through layer-by-layer processing directly from digital models. Among AM techniques, material extrusion–based processes such as fused filament fabrication (FFF) provide an accessible method for producing metal parts using filament feedstocks composed of metal powders and polymer binders. When applied to precipitation-hardening stainless steels such as 17-4 PH, the processing route and heat treatments can influence the resulting microstructure and functional properties. This work investigates the magnetic behavior of 17-4 PH stainless steel fabricated using FFF and evaluates how heat treatment conditions influence measured magnetic properties. Samples were produced and analyzed …

Investigation Of Fine-Grain Cu And Cu Alloys For Low-Temperature Hybrid Bonding Applications, Sarabjot Singh

Electronic Theses & Dissertations (2024 - present)

Hybrid bonding has emerged as a key enabler for next-generation three-dimensional (3D) integration, offering fine-pitch interconnects and improved electrical performance. However, conventional Cu–Cu hybrid bonding typically requires elevated temperatures to achieve sufficient diffusion and interface quality, posing challenges for temperature-sensitive device integration and process compatibility. This work investigates materials engineering approaches to enable low-temperature Cu–Cu bonding through both microstructure design and alloying strategies.

This work begins by examining grain refinement in Cu as a pathway to enhance diffusion through increased grain boundary density, providing efficient atomic transport without introducing additional elements. Three Cu-based systems Cu–Co, Cu–Ag, and Cu–Al were systematically …

Examination Of Laser Microwelding As A Technique For The Repair Of Steel Castings, Allan John Woldow

Masters Theses

"Metal castings have long been plagued with minor defects caused by various process and design conditions. Commonly, minor defects are not seen until after machining operations have been completed, and by the time they are identified, they cannot be salvaged in a manner that is structurally sound and does not have other detrimental effects on the product. Detrimental effects may include warping from high heat input in traditional welding, warping from reheat treatment, oxidation of machined surfaces, microstructural anomalies, and reduced mechanical properties. Micro laser welding has the potential to provide a solution to these issues by providing a low …

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Nanostructured Cathode Catalysts For Aem Electrolysis: From Catalyst Design To Degradation And Hydrogen Dynamics, Yamini Kumaran

Electronic Theses & Dissertations (2024 - present)

Anion exchange membrane water electrolysis (AEMWE) presents a promising pathway toward cost-effective and sustainable hydrogen production by integrating the chemical robustness of alkaline systems with the compact, zero-gap design of proton exchange membrane electrolyzers. However, the widespread implementation of AEMWE is limited by the availability of highly active and durable platinum-group-metal (PGM)-free catalysts and by an incomplete understanding of their degradation behavior under realistic operating conditions.

This dissertation focuses on the development, characterization, and mechanistic investigation of nanostructured MoNi₄–MoO₂-based electrodes for efficient and stable hydrogen generation under alkaline and membrane-integrated environments. MoNi₄–MoO₂ nanorods …

Effects Of Composition, Nodularity, Pouring Temperature, Inoculation, And Mold Strength On Wall-Movement In Sgi Castings During Solidification And Cooling, Noah Brack

College of Graduate Studies: Theses & Dissertations

The iron-carbon casting alloy known as spheroidal graphite iron (SGI), nodular graphite iron, or ductile iron (DI) experiences complex volume changes during its solidification and cooling as graphite nodules and austenite form. These volume changes result in forces on the mold cavity walls and can deform the mold walls in cases when mold walls lack the strength to resist the deformation. This wall movement can cause the formation of casting defects such as swell, warped part geometry, and shrinkage porosity. Though this phenomenon has been studied in the past, it remains difficult to predict casting wall movement with existing data. …

Effect Of Wall Movement On Porosity Formation In Ductile Iron Castings Under Varying Processing Parameters, Shamsul Alam

College of Graduate Studies: Theses & Dissertations

Shrinkage porosity is a major defect that significantly impairs the mechanical properties and overall performance of ductile iron castings. Although graphite formation during solidification induces volumetric expansion, this expansion alone is insufficient to fully compensate for the shrinkage occurring throughout solidification. During the solidification and cooling of ductile iron, multiple phase transformations occur, resulting in dynamic volume changes that exert pressure on mold walls and internal cavities. These pressures can deform mold walls and casting surfaces, leading to defects such as swell and porosity, while also influencing shrinkage formation. This study aims to analyze the mechanisms of porosity formation and …

Multiphysics Modeling Of Melt Pool Dynamics And Powder Bed Stability In Lpbf Of Inconel 718 For A Circular Cavity, Nayan Pundhir, Oluwapelumi O. Adejumo, Kumbla Chandrashekhara, Joseph W. Newkirk, Heath Misak, Cesar Ortiz Rios

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser powder bed fusion (LPBF) is a metal additive manufacturing process in which a concentrated laser beam selectively melts successive powder layers to fabricate components. Final part quality is highly sensitive to process parameters such as hatch spacing, powder bed density, laser power, and scanning speed. In this study, a computational fluid dynamics model employing discrete element method has been developed in FLOW-3D to simulate LPBF of Inconel 718. The modeled powder bed incorporates particle size distribution data obtained from scanning electron microscopy and is evaluated for single-layer, single-track deposition over a circular cavity. The model captured melt pool dynamics …

A Combined Stochastic And Physical Framework For Alloys And Metal Casting Processes Modeling, Simon N. Lekakh, Oleg Neroslavsky

Materials Science and Engineering Faculty Research & Creative Works

High temperature metal casting processes have dualistic nature and conceptually consist of two parts of distinct processes: the first type is deterministic, strictly obeying the physical law, while the second type is stochastic. Therefore, the metal casting processes are not precisely predictable, and deterministic considerations cannot provide exact outcomes. To solve this problem, the combined stochastic and deterministic framework was suggested. The local processes were described using deterministic models for several parameter arrangements, while the distribution of these arrangements on macro level was calculated using stochastic approaches. The approach was used for cast alloy design, investment casting process optimization, and …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

Design Of Novel Gating Systems For Steel Castings, K. Balasubramanian, Laura Bartlett, M. Xu

Materials Science and Engineering Faculty Research & Creative Works

Gating systems play an important role in determining the quality and mechanical properties of castings. To understand the efficiency of gating systems, four systems, namely pressurized system, non-pressurized system, naturally pressurized system with a side riser and a naturally pressurized system with a top riser, were studied. The naturally pressurized systems were provided with overflows which collected the incoming metal swirl. Parameters like velocity of metal flow, air entrapment, microporosity and Niyama criterion were considered, and a design was developed with a common pouring basin. 8630 alloy was poured into two molds using a teapot ladle. The inclusion analysis revealed …

Comparative Evaluation Of Gating Systems In Femnal Castings, K. Balasubramanian, Laura Bartlett, M. Xu

Materials Science and Engineering Faculty Research & Creative Works

To understand the efficiency of gating systems, four systems, namely AFS styled pressurized system, AFS styled non-pressurized system, naturally pressurized system with a side riser and a naturally pressurized system with a top riser, were studied. The naturally pressurized systems were provided with overflows which collected the incoming metal swirl while the pressurized and non-pressurized systems had runner wells. Parameters like velocity of metal flow, air entrapment, microporosity and Niyama criterion were considered, and a design was developed with a common pouring basin using solidification software. Two molds were 3D printed using carbonitride sand, and steel of composition Fe-29Mn-8.2Al-0.91C-0.88Si-0.49Mo was …

N-Radii Approach For Multi-Scale Characterization Of Graphite Shape In Cast Iron, Simon N. Lekakh, Laura Bartlett

Materials Science and Engineering Faculty Research & Creative Works

Knowledge of multi-scale particle macro-shape and micro-surface topology is critical in many technical disciplines. Specifically, quality assessment of the shape of the graphite phase in cast irons is essential for day-to-day metal casting operations. Common methods for evaluating particle macro-shape have several drawbacks, often resulting in underestimation of sharp corners and surface texture. In this article, a method based on plotting n-radii from the center of mass to the perimeter and computing multi-scale topological characteristics is described and tested. Parametric tests, involving variations in the number of n-radii and image resolution, were performed to optimize the test parameters. The method …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Effect Of Elemental Additions On The Microstructure, Macrostructure, And Mechanical Properties Of Gray Iron, August E. Rautmann

College of Graduate Studies: Theses & Dissertations

Gray iron is composed primarily of an iron matrix and flake graphite, with the higher percentage of volume taken up by the iron matrix. The iron matrix is the transformation product of austenite, and this prior austenite structure is understood to affect the final grain structure. Grain structure affects the properties of a metal, with a finer structure recognized as beneficial for most properties. Thus, the refinement of austenite structure has potential in improving the material properties of gray iron. This study aims to advance the limited knowledge about the control of austenite grain size via elemental additions. Building off …

High Temperature Creep Deformation Mechanism Of Fe28.2ni18.8mn32.9al14.1cr6 High Entropy Alloy And Its Modified Alloys, Edwin S. Jiang, I. Baker

Dartmouth College Ph.D Dissertations

Fe28.2Ni18.8Mn32.9Al14.1Cr6 eutectic high entropy alloy exhibits a good combination of room-temperature and high temperature properties, including tensile strength, ductility, and corrosion resistance, making it a promising candidate for structural applications in extreme environments. However, the creep deformation behavior of this alloy— and high-entropy alloys (HEAs) in general—remains insufficiently understood. This dissertation systematically investigates the high-temperature creep deformation mechanisms of Fe28.2Ni18.8Mn32.9Al14.1Cr6 and its derivatives.

Creep mechanisms and associated microstructural changes were examined across a wide range of strain rates using strain-rate jump and constant-stress tests. Two dominant regimes were identified: dislocation glide/solute-drag at low strain rates, and dislocation climb at high …

Aqueous Iron Electrowinning: From Electrolyte Engineering To The Unexplored Potential Of Acetate Systems, Chodwell N. Verenga

Dissertations, Master's Theses and Master's Reports

Iron electrowinning and electrodeposition sit at the intersection of classical metallurgy and developing sustainable manufacturing. With the iron and steel industry responsible for 7 - 9% of global CO₂ emissions, low-temperature electrochemical pathways for iron production have garnered significant research interest. This review examines the fundamental electrochemical principles governing iron deposition, the thermodynamic constraints imposed by the iron-water system, and the kinetic challenges posed by the parasitic hydrogen evolution reaction (HER). The three key electrolyte systems are objectively evaluated: acidic sulfate and chloride electrolytes, alkaline suspension electrolytes and water-in-salt electrolytes. Their operating parameters, faradaic efficiencies, energy consumption and deposit characteristics …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Recycling Ndfeb Magnets I: Production Of Ree Fluorides By A Novel Lpc Process, Isaac Joseph Cobbinah

Graduate Theses & Non-Theses

Neodymium-iron-boron (NdFeB) magnets account for over 60% of global magnet sales and are widely used in high-tech, military, and clean-energy applications (Ormerod, 2022). However, they contain critical rare earth elements such as Nd, Pr, and Dy which poses supply chain and geopolitical risks for country like the United States, which rely extensively on foreign sources. Recycling end-of-life NdFeB magnets provides a sustainable solution that diminishes environmental impact, strengthens supply security, and supports stable domestic production of important rare earth elements. A three-stage process has been developed for recycling the REE-content of NdFeB magnets. While the focus is on neodymium (Nd), …

Process Intensification For Rare Earth Elements Adsorption By Resonant Vibratory Mixing (Rvm), Mehran Saddat

Graduate Theses & Non-Theses

Rare earth elements (REE) are crucial to the advancement of modern technologies. REE applications include electronics, defense systems, wind turbines, catalysts, magnets, and aircraft. Bastnasite, monazite, and xenotime are the primary resources, while the secondary resources, including coal ash, E-waste, and acid mine drainage, are for REE extraction. The primary processing techniques are chemical leaching, ion exchange, chemical precipitation, pyrometallurgy, solvent exchange, biosorption, and adsorption. Adsorption technique is simple, cost-effective, and environmentally friendly, with higher efficiency but at the cost of a longer mixing time. Therefore, there is a pressing need for an optimized mixing technique to improve the adsorption …

Production Of Rare Earth Elements By Molten-Salt Electrolysis, Mohammed Moro

Graduate Theses & Non-Theses

Rare earth elements (REEs) are indispensable, high-value resources that play a crucial role in renewable energy, defense systems and advanced technological systems. REEs are commonly extracted from natural ores or recycled materials such as permanent magnets using hydrometallurgical or pyrometallurgical techniques. In hydrometallurgy, the REE source is leached with acid, followed by solvent extraction and precipitation steps to obtain rare earth compounds like oxides and fluorides. Pyrometallurgy involves dissolving rare earth compounds in a molten halide bath, followed by high-temperature electrolysis to convert them into metals, which are then recovered at the cathode. This process typically includes melting, refining, and …

The Comparison Of Dixon–Mood And 1/Nf Methods For Fatigue Limit Estimation Of 17–4 Ph Stainless Steel (H900), Arthur Pallar Pallar

Masters Theses

This study compares two methods for estimating the fatigue limit of 17-4 PH stainless steel (H900): the Dixon–Mood staircase and Kujawski 1/Nf linear method. Tests were conducted on an MTS Acumen 3 kN system under axial tension–tension loading at R = 0.1 and 50 Hz, following the standard practice defined in ASTM E466-15. Flat specimens were fabricated by water-jet cutting and polished. Tensile tests verified mechanical properties consistent with published data for the H900 condition. Fifteen specimens tested by the staircase method yielded a mean fatigue limit of 1138 MPa. The 1/Nf analysis using four specimens produced 1159 MPa, 2 …

L.G. Twidwell: A Summary Of Fifty-Six Years Of Research, Larry G. Twidwell

Metallurgy

No abstract provided.

L.G. Twidwell: A Summary Of Fifty-Six Years Of Research, Larry G. Twidwell

Metallurgical & Materials Engineering

No abstract provided.

Tensile Performance Sensitivity To Variations Of Standard 17-4 Ph Heat Treatments On Lpbf-Produced Material, Ben Brown, Cory Read, Joseph Newkirk, Frank Liou

Materials Science and Engineering Faculty Research & Creative Works

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical …

Chemistry Of Inclusions By Size In Three Primary Copper Anodes, Charles Campbell, Michael Moats

Materials Science and Engineering Faculty Research & Creative Works

Three copper anodes from different commercial electro refineries were characterized to measure inclusion chemistry, size (diameter), and morphology. An automated scanning electron microscope (SEM) paired with energy-dispersive X-ray spectroscopy (EDS) was used to examine hundreds of inclusions near the mold and set sides of each anode. The investigation revealed that in the two anodes with less impurities (99.65% Cu and 99.75% Cu), many of the inclusions were Cu2O with an average diameter of 2 microns. The greater impurity anode (99.05% Cu, 4076 ppm Pb, 1939 ppm As, 635 ppm Bi) contained significant numbers of complex oxide inclusions, averaging 4.6 microns …