Materials Science and Engineering Commons^™

High Temperature Heat Exchanger Project:Quarterly Progress Report January 1, 2005 Through March 31, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. Ceramatec, Inc. hosted a UNLVRF HTHX Project quarterly meeting on March 17 in Salt Lake City, Utah. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in June in San Diego City hosted by General Atomics.

Detection Of Residual Stress In Sic Mems Using Μ-Raman Spectroscopy, John C. Zingarelli

Theses and Dissertations

Micro-Raman (µ-Raman) spectroscopy is used to measure residual stress in two silicon carbide (SiC) poly-types: single-crystal, hexagonally symmetric 6H-SiC, and polycrystalline, cubic 3C-SiC thin films deposited on Si substrates. Both are used in micro-electrical-mechanical systems (MEMS) devices. By employing an incorporated piezoelectric stage with submicron positioning capabilities along with the Raman spectral acquisition, spatial scans are performed to reveal areas in the 6H-SiC MEMS structures that contain residual stress. Shifts in the transverse optical (TO) Stokes peaks of up to 2 cm^-1 are correlated to the material strain induced by the MEMS fabrication process through the development of phonon …

A Three Dimensional Finite Element Model For Emergency Response, Xiuling Wang, Darrell W. Pepper, Yitung Chen, Sean Hsieh

Mechanical Engineering Faculty Research

No abstract provided.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii, Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities in the no-cost extension period. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. In December of 2005, the software for the particle positioning detector was finally up …

Vibrational Behavior Of The MN+1AxN Phases From First-Order Raman Scattering (M=Ti,V,Cr, A=Si, X=C,N), Jonathan E. Spanier, Surojit Gupta, Maher S. Amer, Michel W. Barsoum

Mechanical and Materials Engineering Faculty Publications

We report on the Raman spectra of Ti₃SiC₂ (312), M2AlC(211) (M=Ti, V, Cr, and Nb) and Ti4AlN3 (413), as representative compounds from the family of Mn+1AXn phases. Intense and narrow first-order Raman peaks are observed, and we present an analysis of the spectra based on symmetry considerations and from results of first-principles calculations of phonon frequencies. The agreement between experimental and calculated mode energies is excellent. The identification of the modes enables application of Raman scattering as a diagnostic tool for the detailed study of the structural and physical properties of this family of compounds and their …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of accelerator driven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. …

Unsteady Tip Leakage, Bow Shock, Igv Wake Interaction In A Compressor, Xuedong Zhou, J. Mitch Wolff

Mechanical and Materials Engineering Faculty Publications

Unsteady aerodynamic analysis of Inlet Guide Vane (IGV)/rotor interaction is conducted with a commercial CFD solver, STAR-CD. 12% and 26% IGV axial chord IGV/Rotor spacing configurations were examined for 100% corrected speed at choke, peak efficiency and near stall conditions to investigate bow shock/tip leakage interaction within blade rows. Comparison with IGV surface unsteady pressure experimental data indicates good agreement at the IGV trailing edge across the span for both spacing configurations; therefore, validating the modeling of the high speed, highly loaded transonic compressor. The strongest effect on the tip clearance flow physics was caused by decreasing the axial spacing. …

Mechanics Of Composite Materials In Fuel Cell Systems, Kenneth Reifsnider, Xinyu Huang, G. Ju, Matthew Feshler, K. An

Faculty Publications

The science and technology that are fundamental to the concept of composite materials are also the foundation for the construction and function of fuel cells and fuel cell systems. The present paper outlines this relationship in the context of the physics and chemistry that are enabled by the specific selection and arrangement of constituents of the “functional composite” fuel cell. General principles of operation are described, and fundamental issues are defined that must be addressed by the composites community if the fuel cell science and engineering is to advance. Examples of several types of functional composite fuel cells are presented, …

High Temperature Heat Exchanger Project: Quarterly Progress Report October 1, 2004 Through December 31, 2004, Anthony Hechanova

Publications (NSTD)

UNLV hosted an NHI Systems Interface Meeting on Dec. 16 and a UNLVRF HTHX Kickoff Meeting on Dec. 17. The purpose of the meetings was to coordinate the FY05 research and development effort of the UNLV Research Foundation portion of the Nuclear Hydrogen Initiative among the DOE, national program technical directors and the UNLVRF collaborators. Collaborators also had the opportunity to discuss their research program plan and update their progress. It was decided that these type of collaboration meetings were very useful and they will be held quarterly at the various collaborator sites. The next meeting will be in March …

Fuel Injection System For One Cylinder Motor Cycle Engine, Bambang Sugiarto

Makara Journal of Technology

Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel …

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …

Modelling And Simulation Of Packed Bed Catalytic Converter For Oxidation Of Soot In Diesel Powered Vehicles Flue Gas, Mohammad Nasikin, Praswasti P.D.K. Wulan, Vita Andrianty

Makara Journal of Technology

Modelling and Simulation of Packed Bed Catalytic Converter for Oxidation of Soot in Diesel Powered Vehicles Flue Gas. Diesel vehicle is used in Indonesia in very big number. This vehicle exhausts pollutants especially diesel soot that can be reduces by using a catalytic converter to convert the soot to CO2. To obtain the optimal dimension of catalytic converter it is needed a model that can represent the profile of soot weight, temperature and pressure along the catalytic converter. In this study, a model is developed for packed bed catalytic converter in an adiabatic condition based on a kinetic study that …

The Effects Of Influent Debit On Hydrodynamic Characteristic Of Bojongsoang Facultative Pond: Without Wind Effects, Rositayanti Hadisoebroto, Suprihanto Notodarmojo

Makara Journal of Technology

The Effects of Influent Debit on Hydrodynamic Characteristic of Bojongsoang Facultative Pond: Without Wind Effects. The performance of facultative pond in Bojongsoang WWTP have reported to be unstable. One of the cause of the unstable performance is the hydrodynamic characteristics that not met the criterion. The improper hydrodynamic characteristics are included the existence of dead-zone, the short-circuiting, and the turbulence due to eddy current. The study was to analyze the effect of the influent debit variation on the hydrodynamic characteristics of the pond using mathematical model. The two-dimensional hydrodynamic model was built from two hydrodynamic equations which are continuity and …

Stress Corrosion Cracking And Hydrogen Embrittlement Of Martensitic Alloy Ep-823, Mohammad K. Hossain

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC), localized corrosion, and hydrogen embrittlement (HE) susceptibility of martensitic Alloy EP-823 in neutral and acidic solutions at ambient and elevated temperatures. While no failures were observed in smooth specimens in the neutral solution, failures were noticed in the 90°C acidic solution at constant-load (CL) leading to a threshold stress (O'_th) of 102 ksi. The presence of a notch reduced the O'_th value to 91 ksi in a similar environment. The ductility (%El and %RA), time-to-failure (TTF), and true failure stress (O'_r) were gradually …

Environment Assisted Cracking Of Target Structural Materials Under Different Loading Conditions, Venkataramakrishnan Selvaraj

UNLV Theses, Dissertations, Professional Papers, and Capstones

Martensitic Alloy HT-9 has been tested for its evaluation of stress corrosion cracking resistance in neutral and acidic solutions at ambient and elevated temperatures incorporating smooth and notched cylindrical specimens under constant load and slow strain rate (SSR) conditions. C-ring and U-bend specimens have also been tested for stress corrosion cracking evaluation in the acidic solution. The role of hydrogen on the cracking tendency has been evaluated by cathodic applied potential.

The results of constant load testing enabled the determination of the threshold stress for stress corrosion cracking in susceptible environments. The magnitudes of ductility parameters were reduced with increasing …

Stress Corrosion Cracking Resistance Of Martensitic Stainless Steels For Transmutation Applications, Phani P. Gudipati

UNLV Theses, Dissertations, Professional Papers, and Capstones

The susceptibility of Alloy EP-823 to stress corrosion cracking has been evaluated using smooth and notched cylindrical specimens in neutral and acidic solutions at ambient and elevated temperatures using constant load and slow strain rate testing (SSR) techniques. C-ring and U-bend specimens have also been tested in the acidic solution. The effect of hydrogen on the cracking susceptibility has been evaluated under controlled cathodic potential. While no failures were observed with smooth specimens at constant load, the notched specimens showed failure. The SSR test results indicate that the true failure stress (o'_f), time to failure and ductility parameters …

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Iii: Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. At a particular beam energy, the current measured with the Faraday cup and electrometer changed sign over a range …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2004 Through September 30, 2004, Anthony Hechanova

Publications (NSTD)

UNLV hosted a meeting on NHI Materials and Heat Exchanger Design on Monday, May 17. Paul Pickard (Sandia National Lab) and Bill Corwin (Oak Ridge National Lab) facilitated the meeting. The purpose of the meeting was to summarize the hydrogen materials and heat exchanger requirements and priorities for UNLV staff and their collaborators to support the research proposal solicitation for the UNLV Research Foundation HTHX program. Attendance was heavier than anticipated and required a change of venue to accommodate the crowd of over 30.

Study Of Ceramic Slurries For Investment Casting With Ice Patterns, Qingbin Liu, Ming-Chuan Leu, Harish Jose, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ice patterns generated by rapid freeze prototyping or a molding process can be used to make ceramic investment molds for metal castings. Due to the use of ice, the ceramic slurries must be poured around the pattern and cured at sub-freezing temperatures. Success of this process depends greatly on the mold strength after the gelation of the slurries. This paper describes the experimental results of the mold strength after the gelation of the slurries under different compositions. The parameters considered include mixing time, alumino-silicate vs. fused silica ratio, volume of binder, and volume of catalyst. The strength of the gelled …

Effect Of Photoperiodicity On Co2 Fixation By Chlorella Vulgaris Buitenzorg In Bubble Column Photobioreactor For Food Supplement Production, Anondho Wijanarko, Dianursanti Dianursanti, Arief Budi Witarto, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

To reduce the level of CO2 content in air, effort on converting CO2 to useful products is required. One of the alternatives includes CO2 fixation to produce biomass using Chlorella vulgaris Buitenzorg. Chlorella vulgaris Buitenzorg is applied for production of food supplement. Chlorella vulgaris Buitenzorg is also easy to handle due to its superior adaptation. Currently, Chlorella vulgaris Buitenzorg has been analyzed by some experts for its cellular composition, its ability to produce high quality biomass and the content of essential nutrition. A series of experiments was conducted by culturing Chlorella vulgaris Buitenzorg using Beneck medium in bubbling column photobioreactor. …

Secondary Flow Experimental Study For Axial Compressor Cascade Strong Stagger With And Without Tip- Clearance: Static Pressure Distribution On Blade Surface, Syamsuri Syamsuri

Makara Journal of Technology

Secondary Flow Experimental Study for Axial Compressor Cascade Strong Stagger With and Without Tip- Clearance: Static Pressure Distribution on Blade Surface. The performance of blade cascade is influenced by the growth and boundary layer’s separation along blade surface and endwall (casing and hub). The secondary flow which happens near hub and casing compressors is three dimentional flow separation phenomenon comes from interaction blade boundary layer with casing and hub boundary layers in the compressor. The secondary flow causes secondary losses, blockage effect, and turning angle (deflection) distribution along blade span. The result of the research shows that the increase of …

Synthesize Of Emulsion Polymer Latex For Sub-Grade Cbr Improvement In The Road Construction, Keba Moto, V. Julian, Syamsudin Syamsudin, T. A. Wiradi, S. R. Wijaya

Makara Journal of Technology

Synthesize of emulsion polymer latex for sub-grade CBR improvement in the road construction. Latex polymer for California Bearing Ratio (CBR) enhancement in sub-grade soil of road building has been prepared by emulsion polymerizations technique. The prepared polymer then characterize by Fourier Transform Infrared (FTIR). For application purpose, CBR test was done to the compacted polymer added-soil. The CBR test is done also for both soaked and unsoaked samples. It is found that our latex polymer is better then other imported latex polymer. For the latex polymer, which is design to have Temperatur glass (Tg) around 9.8-19.6o, indicating the formation of …

Wavelenght-Dispersive X-Ray Flourescence Accuration, H. Widyatmoko

Makara Journal of Technology

Wavelenght–Dispersive X-Ray Flourescence Accuration. X-Fuorescence spectrometry is a method, which is increasingly applied in the geochemical analysis. X-Fuorescence spectrometry is classified under two categories – WDXRF (wavelenght – dispersive X-ray fluorescence spectrometer) and EDXRF (energy-dispersive X – ray fluorescence spectrometer). WDXRF can be configured as a sequential spectrometer , a simultaneous spectrometer or a hibrid instrument, which combines the advantages of the simultaneous and sequential spectrometers into one instrument. Each instrument is different in some characteristics, and each has applications for which it is specifically suited. In this investigation sequential spectrometer PW 1450 was used to analyze the major, minor …

Environment-Induced Degradations In A Target Structural Material For Transmutation Applications, Ramprashad Prabhakaran

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC) and localized corrosion behavior of Type 422 stainless steel in aqueous environments at ambient and elevated temperature. The results of constant load SCC testing using smooth specimens showed no failure in the neutral solution but a threshold stress of 97 ksi was observed in the 90°C acidic environment. SCC testing by the slow-strain-rate test method indicate that the time-to-failure, true failure stress and ductility parameters were gradually reduced with increasing temperature, showing more pronounced effect in the acidic solution. The application of a controlled cathodic potential showed further …

Embrittlement And Localized Corrosion In Alloy Ht-9, Sudheer Sama

UNLV Theses, Dissertations, Professional Papers, and Capstones

This investigation is focused on the evaluation of stress corrosion cracking (SCC), hydrogen embrittlement (HE) and localized corrosion susceptibility of Alloy HT -9 in neutral and acidic solutions at 30, 60 and 90°C. Constant-load and slow-strain-rate (SSR) testing techniques were used to evaluate the SCC and HE behavior of this alloy by using smooth and notched tensile specimens. Hydrogen effect on the cracking behavior was evaluated by applying cathodic (negative) potential to the test specimens. Localized corrosion susceptibility was evaluated by cyclic potentiodynamic polarization technique. The results of constant load SCC testing showed a threshold stress at 80% of the …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2004 Through June 30, 2004, Anthony Hechanova

Publications (NSTD)

UNLV hosted a meeting on NHI Materials and Heat Exchanger Design on Monday, May 17. Paul Pickard (Sandia National Lab) and Bill Corwin (Oak Ridge National Lab) facilitated the meeting. The purpose of the meeting was to summarize the hydrogen materials and heat exchanger requirements and priorities for UNLV staff and their collaborators to support the research proposal solicitation for the UNLV Research Foundation HTHX program. Attendance was heavier than anticipated and required a change of venue to accommodate the crowd of over 30.

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded, bent (three-point-bend), and cold-worked engineering materials using a new nondestructive technique based on positron annihilation spectroscopy (PAS). The proposed technique is to use γ-rays from a small MeV electron linear accelerator (Linac) to generate positrons inside the test sample via 2 pair production. This method can be used for materials characterization and investigation of defects in thick samples that usually cannot be accomplished by conventional positron technique or other …

Studies On Yba2nbo6 And Yba2cu3-Xnbxoy Buffer Layers, S. Sathiraju, R. Wheeler, Paul N. Barnes, T. L. Peterson, Iman Maartense, A. L. Campbell, N. A. Yust, T. J. Haugan, Q. Jia, Paul Arendt, Sharmila M. Mukhopadhyay, S. Vemulakonda

Mechanical and Materials Engineering Faculty Publications

No abstract provided.

Construction Of Depth-Structure Shelf-Edge Map For Case Study Of Kujung Formation, East Java Sea, Saifatur Rusli, Suparto Suparto

Makara Journal of Technology

Construction of Depth-Structure Shelf-edge Map for Case Study of Kujung Formation, East Java Sea. In general, reflection seismic method has capability to represent sub-surface in time domain. Seismic cross-section that depicts the formation of sub-surface usually use time domain in the format of TWT (Two Way Times). This due to in the process of seismic data acquisition, seismic wave propagates in down-going and up-going manner so that the obtained results from data processing are in the format of TWT seismic vs. shot points. This paper will describe the construction of depth-structure map for case study of Kujung Formation, East Java …