Materials Science and Engineering Commons^™

Pid Fuzzy Logic Controller System For Dc Motor Speed Control, H. Samsul Bachri M.

Makara Journal of Technology

PID Fuzzy Logic Controller System for DC Motor Speed Control. A good controller system must have resilience to disturbance and must be able to response quickly and accurately. Problem usually appears when PID controller system was built sensitively hence the system’s respon to the disturbance will yield big overshot/undershot then the possibility of oscillation to be happened is excelsior. When the controller system was built insensitively, the overshot/undershot will be small but the recovery time will be longer. Hybrid controller system could overcome those problems by combining PID control system with fuzzy logic. The main control of this system is …

Analysis Of Kancil's Car Knuckle Prototype, Tresna P. Soemardi, Aida Mahmudah

Makara Journal of Technology

Analysis of Kancil’s Knuckle Prototype. The objective of this work is to execute strength analysis of knuckle, which is made from FCD 50, by using static analysis on maximum loading. This maximum loading is obtained from front axle loading calculation on particular operating condition. That is, vehicle is braking while cornering in down hill. From previous vehicle loading calculation, we get a number of loading values on different speed and deceleration. At the end, we get a value of speed and deceleration that guarantee the vehicle safety if it is braking while cornering in down hill. As comparison, loading calculation …

Quarternair Cugasete And Cuga0.5in 0.5te2 Thin Films Fabrication Using Flash Evaporation, A. Harsono Soepardjo

Makara Journal of Technology

Quarternair CuGaSeTe and CuGa0.5In 0.5Te2 Thin Films Fabrication Using Flash Evaporation. Quarternair materials CuGaSeTe and CuGa0.5In 0.5Te2 are the basic materials to solar cell fabrication. These materials have high absorption coefficients around 103 – 105 cm-1 and band gap energy in the range of 1-5 eV. In this research, the films were made by flash evaporation method using quarternair powder materials of CuGaSeTe and CuGa0.5In 0.5Te2 to adhere in a glass substrate. After the films were obtained, the properties of these films will be characterized optically and electrically. The lattice parameter of the films and the crystalline film structure were …

Graded Channel Mosfet Simulation With S-Pisces 2b, Hartono Siswono

Makara Journal of Technology

Graded Channel MOSFET simulation with S-Pisces 2B. Graded-Channel Metal-Oxide-Semiconductor Field-effect- Transistor or GCMOSFET is being discussed in this paper. GCMOSFET technology has been developed to meet the growing demand for low power and high performance application. In this paper, it will be shown that, compared to ungraded MOSFET, the GCMOSFET device offers the advantage of significantly higher drive current. The higher drive current is achieved because the effecctive channel length of GCMOSFET is shorter than the ungraded MOSFET’s. From the simulation result with S-PISCES 2B and MATLAB, it can been shown that the ID from GCMOSFET is higher than the …

High Temperature Heat Exchanger Project: Quarterly Progress Report January 1, 2004 Through March 31, 2004, University Of Nevada, Las Vegas. Research Foundation, Robert F. D. Perret

Publications (NSTD)

Mutually satisfactory language has been developed to permit signing of a subcontract between the General Atomics Corporation and the UNLV Research Foundation. The contract is signed.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

High Temperature Heat Exchanger Project (Hthx) Project Quarterly Report, University Of Nevada, Las Vegas. Research Foundation

Publications (NSTD)

On October 24, 2003, the University of Nevada, Las Vegas (UNLV) hosted an all-day HTHX Kickoff Meeting attended by all participating institutional representatives and researchers. Objectives of this meeting were to identify near-term research objectives, coordinate collaborative activities, and identify required urgent action items.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Second Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Joining Challenges In The Packaging Of Biomems, Hans Herfurth, Reiner Witte, S. Heinemann, Golam Newaz, Ahsan Mian, Daniel Georgiev, Greg Auner

Mechanical and Materials Engineering Faculty Publications

Micro-joining and hermetic sealing of dissimilar and biocompatible materials is a critical issue for a broad spectrum of products such as micro -electronical, micro -optical and biomedical products and devices. Novel implantable microsystems currently under development will include functions such as localized sensing of temperature and pressure, electrical stimulation of neural tissue and the delivery of drugs. These devices are designed to be long-term implants that are remotely powered and controlled. The development of new, biocompatible materials and manufacturing processes that ensure long-lasting functionality and reliability are critical challenges. Important factors in the assembly of such systems are the small …

Cfd Analysis Of Unsteady Separated Transonic Oscillation Cascade Aerodynamics, Xuedong Zhou, J. Mitch Wolff

Mechanical and Materials Engineering Faculty Publications

With an improved algebraic mesh-deforming algorithm, STAR-CD, a commercial computational fluid dynamics (CFD) solver is employed for the numerical analysis of a transonic oscillating linear cascade of advanced design blades. The center blade oscillates 0.6-degrees about the middle cord. The numerical simulation is conducted for a frequency range from 200 Hz to 500 Hz. A hybrid grid, which utilizes a structured O-grid around the airfoil and an unstructured grid everywhere else is employed. The Spalart-Allmaras (S-A), one equation turbulence model, along with other two equation k-ε models, are also utilized for the steady state simulation. The S-A turbulence …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of acceleratordriven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. Furthermore, …

Characterization And Modeling Of Local Electromechanical Response In Stress-Biased Piezoelectric Actuators, N. Navapan-Traiphol, Robert W. Schwartz, Daniel S. Stutts, J. Wood

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Numerous investigators have explored the factors that contribute to the high electromechanical performance of stress-biased actuators with particular attention being given to the importance of the extrinsic (domain wall translation) response mechanism. Based on the variation in lateral stress through the thickness of the piezoelectric layer within these devices, it has been suggested that the piezoelectric coefficient varies as a function of position within the layer, though no direct evidence has been previously presented. In this study, the results of Moire interferometry investigations of local strains within these devices are reviewed. The technique permits effective depth-profiling of local deformations at …

Alum And Pacl Coagulation, Winarni Winarni

Makara Journal of Technology

Alum and PACl Coagulation. Coagulation occurs by interaction of aluminum hydrolysis products with the contaminant such as colloidal particles. It is necessary to consider the different aluminum species that may present during specific conditions, since the mechanism of turbidity removal is dependent upon them. PACl consists of preformed aluminum hydrolysis products, which are stable below pH 6 and less sensitive than in situ hydrolysis product, alum. The benefits of PACl relative to alum have been investigated as a function of pH and Al dosages. Specific conditions and aluminum species that exist during the certain mechanisms of coagulation are discussed. Results …

The Selection Of Materials For Roller Chains From The Perspective Of Manufacturing Process, Rahmat Saptono

Makara Journal of Technology

The selection of materials for an engineering component is not only requested by its design function and shape, but also the sequence through which it is manufactured. The manufacturing operation of roller chains involves drawing and trimming processes aimed at producing semi-finished chain drives component with a well-standardized dimension. In addition to final combination of properties required by design constraints, the ability of materials to be formed into a desired shape and geometry without failure is also critical. The objective of materials selection should therefore involve additional attributes that are not typically accommodated by the standard procedure of materials selection. …

Adoption Of Variable Rate Technology, Isti Surjandari, Marvin T. Batte

Makara Journal of Technology

Site Specific Management (SSM), which also variously referred to as Variable Rate Technology (VRT), is an emerging technology that enables producers to make more precise input application decisions based on soil and field characteristics. This study analyzes factors influencing the adoption of VRT for fertilizer application for cash grain production in Ohio. Results show that producer and field characteristics might influence the adoption decision on various SSM components differently. It also provides insight as to the sequence of adoption of SSM component technologies and how this sequence might differ for producers of differing characteristics.

Study On Electrochromic Effect Of Polyaniline Film, Lienda Handojo, Junus Simangunsong

Makara Journal of Technology

Study on Electrochromic Effect of Polyaniline Film. The light transmission factor of an electrochromic film changes reversibly with the application of an electrical voltage. Thereby the transparent film becomes reversibly opaque so that it may be used to control light transmission. In this paper the results of a study on polyaniline film as an electrochromic active material is reported. Polyaniline looks yellow transparent in the reduced state and turns to green-blue at its oxidized state. The electrochromic device considered in this paper was fabricated in planar configuration of ITO glass − polyaniline film − electrolyte − ITO glass which involved …

An Economic Analysis Of Variable Rate Technology, Isti Surjandari, Marvin T. Batte, Mario J. Miranda

Makara Journal of Technology

Variable Rate Technology (VRT) offers an opportunity to improve production efficiency by allowing input applications to fluctuate in response to spatial variations in soil characteristics and nutrient levels. Society may also benefit from reduced negative externalities, such as surface and groundwater contamination, from input applications. Using a dynamic spatial model, this study examines how the interaction among variability, spatial autocorrelation, and mean level of soil fertility affects optimal sampling density and the economic gains from VRT. VRT was found to be profitable under selected conditions, and the optimal grid size will vary with these conditions. In the case where variability …

Application Of Tabu Search Algorithm In Job Shop Scheduling, Betrianis Betrianis, Putu Teguh Aryawan

Makara Journal of Technology

Application of Tabu Search Algorithm in Job Shop Scheduling. Tabu Search is one of local search methods which is used to solve the combinatorial optimization problem. This method aimed is to make the searching process of the best solution in a complex combinatorial optimization problem(np hard), ex : job shop scheduling problem, became more effective, in a less computational time but with no guarantee to optimum solution.In this paper, tabu search is used to solve the job shop scheduling problem consists of 3 (three) cases, which is ordering package of September, October and November with objective of minimizing makespan (Cmax). …

Role Of K3-Xhxpw12o40 As A Catalyst In Selective Catalysis Of Methylamine Synthesis From Ammonia And Methanol, Mohammad Nasikin

Makara Journal of Technology

Role of K3-xHxPW12O40 as a Catalyst in Selective Catalysis of Methylamine Synthesis from Ammonia and Methanol. Synthesize of methylamine from methanol and ammonia was studied in this research work using a partially potassium heteropoly salt (K3-xHxPW12O40 abbreviated as KPW) as a catalyst. KPW was prepared from heteropoly salt and potassium carbonate by using ion exchange method. The reaction was conducted at 600 ~ 800K and at the atmospheric pressure. Reactor used was a continue flow reactor with W/F=0,1~0,9g-kat.mnt./cc.Concentration of reactants and products were analyzed by gas chromathography while catalyst structure was observed by XRD (X-ray diffraction). Isothermal adsorption method was …

Identification Of The First Limiting Amino Acid In Cooked Polished White Rice Fed To Weanling Holtzman Rats, Mellova Masrizal, J. B. Lamb

Makara Journal of Technology

Forty-eight male weanling rats (91 g) were utilized to study the nutritional adequacy of cooked polished white rice. Rats were individually housed, and allowed ad libitum access to one of six treatment diets. Treatment diets were 1) polished white rice plus 10% casein and 0.18% methionine, CAS, 2) polished white rice, WHR, 3) polished white rice plus 0.45% lysine, LYS, 4) polished white rice plus0.40% methionine, MET, 5) polished white rice plus 0.30% threonine, THR, 6) polished white rice plus 0.45% lysine, 0.40% methionine, and 0.40% threonine, COM. Rice was cooked prior diet formulation using a 3 to 1 ratio …

Riser Design For Green Sand And Ductile Iron Castings, K. Michael Kuebler

Graduate Research Papers

Shrinkage defects in ductile iron riser contacts has long been one of the most frustrating defects to eliminate for the foundry engineer. While process variation can definitively contribute to the occurrence of these defects most can be prevented if the risers are properly designed and/or applied to the castings to be fed. There are several proven methods for the designing risers some of which go back over 40 years ago. There are also new methods available today with the advancements of simulation software. Four of these riser design methods were evaluated for their ability to produce an internally sound casting …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 01 – August 31, 2003), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed (bent), and welded materials using a nondestructive method based on positron annihilation spectroscopy (PAS). This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens that could not be accomplished by conventional positron technique or other nondestructive methods. The generated …

External And Intrinsic Anchoring In Nematic Liquid Crystals: A Monte Carlo Study, Nikolai V. Priezjev, G. Skacej, R. A. Pelcovits, S. Zumer

Mechanical and Materials Engineering Faculty Publications

We present a Monte Carlo study of external surface anchoring in nematic cells with partially disordered solid substrates, as well as of intrinsic anchoring at free nematic interfaces. The simulations are based on the simple hexagonal lattice model with a spatially anisotropic intermolecular potential. We estimate the corresponding extrapolation length b by imposing an elastic deformation in a hybrid cell-like nematic sample. Our estimates for b increase with increasing surface disorder and are essentially temperature independent. Experimental values of b are approached only when both the coupling of nematic molecules with the substrate and the anisotropy of nematic-nematic interactions are …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Diffuser Optimation At Exhaust System With Catalytic Converter For 110 Cc Mopet With Fluid Flow Cfd Simulation, Tresna P. Soemardi, Ahmad Indra Siswantara, Erwin Erwin

Makara Journal of Technology

Diffuser Optimation at Exhaust System with Catalytic Converter for 110 cc Mopet with Fluid Flow CFD Simulation. CFD simulation used to get behavior of exhaust gas through catalyst, this result will be used to optimize geometry form to perform uniform stream distribution to catalyst, and CFD Simulation will used to analyze backpressure that happened at the model.

The Study On Fluorescence Characteristics Of Chlorella Spp: Ph Influence On Culture, Retno Wigajatri P., Andrianto Handojo, Hendrik Kurniawan, N. B. Prihantini

Makara Journal of Technology

The Study on Fluorescence Characteristics of Chlorella spp: pH Influence on Culture. Experiments for measuring the fluorescence characteristics of Chlorella spp. by using high stability and high repetition rate nitrogen laser of energy 5 mJ with pulse duration of 5 ns have been carried out. The results show that for a cell concentration range from 2,625 cells/ml up to 2,769,000 cells/ml, the fluorescence intensities at pada λ = 687 nm have a linear relationship with the cell concentration. It has been also found that for a 7 days old chlorella culture, the pH variation at the starting culture influenced the …

Capacity Of High-Speed Powerline Communication In Vehicles, Deny Hamdani, Ery Safrianti

Makara Journal of Technology

Powerline Communication (PLC) Systems intents to use the mains network in vehicles for high-speed data transmission. Carrier frequencies in the range of MHz are required to establish data rates of some megabits per second. In this paper, typical reference channels extracted from channel measurements are presented and computation results of their capacities according to Shannon’s theorem are presented. Furthermore, the effect of limitations of frequency range and power spectral density of transmitted signal on achievable capacity is investigated. This paper outlines an assessment for theoretical channel capacity and achievable data rates of vehicular PLC transmission schemes. Finally, EMC (Electromagnetics Compatibility) …

The Performance Analysis Of A Unicast Network When Two Protocols, Sctp (Stream Control Transmission Protocol) And Tcp (Transmission Control Protocol) Coexist In The Network, Bagio Budiardjo, Michael Thiotrisno

Makara Journal of Technology

This paper elaborates the performance analysis of a unicast network when two protocols, SCTP (Stream Control Transmission Protocol) and TCP (Transmission Control Protocol) coexist in the network. These two protocols are tested using File Transfer Protocol (FTP) and Constant Bit Rate (CBR) based traffic. From the simulations, it could be concluded that SCTP could achieve better throughput compared to TCP in both FTP and CBR based traffic, with sufficiently high fairness index of both intrafairness and interfairness. The increase of simulation time yields to the increase and relatively stable network performance. The increase of the number of sessions of small …

Mapping Of Ecosystems In Mount Bromo Using Remote Sensing Technology, Bangun Muljo Sukojo

Makara Journal of Technology

Mapping of Ecosystems in Mount Bromo Using Remote Sensing Technology. Covered land analyses of Landsat image have been done to get ecosystem types and map in Mount Bromo region using remote sensing technology. There are nine types of ecosystems in Mount Bromo region, i.e. primary forest, secondary forest, lake, crater, sands, uncovered land, underbrush, dry-field and residence. Distribution of rock analysis has also been done by comparing the manual image interpretation with geological map. The results were coorelated with the digital image interpretation to find rock distribution map which can be useful to get the information about water reservation potencial …

Development Of Advanced High Temperature Heat Exchangers: Proposal, University Of Nevada, Las Vegas. Research Foundation

Publications (NSTD)

A research team led by the University of Nevada, Las Vegas (UNLV) Research Foundation proposes a project to develop advanced high temperature heat exchangers (HTHX) for hydrogen production and electrical energy conversion from advanced nuclear reactor concepts. This project will also support the development of Generation IV reactors. The research team includes researchers from UNLV, General Atomics (GA), Sandia National Laboratories (SNL), The University of California, Berkeley UCB) and Oak Ridge National Laboratory (ORNL).

The proposed project will be administered by the University of Nevada Las Vegas Research Foundation (UNLVRF). UNLVRF will provide the overall contract administration and is the …