Materials Science and Engineering Commons^™

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Self-Organized Nanolayers Of Organosilane Molecules, Ocelio V. Lima

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

There is a high degree of interest in organic thin films for lightweight, low power, rugged and flexible electronics. Conjugated organic molecules with polycyclic rings are being considered a major enabler of such applications. Due to a surface tension mismatch between the organic molecule with the inorganic support (mainly silicon oxides), molecular packing inside these thin films is often disordered, which suppresses the device performance. There are major efforts focused on modifying the bulk properties, for instance, maximizing orbital overlaps in the solid state, little attention was paid to receive long-range ordered thin films. A novel approach to afford conjugated …

Optical Properties Of Semiconducting Boron Carbide For Neutron Detection Applications, Ravi B. Billa

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Solid state neutron detection devices based on semiconducting boron carbide have the potential for nearly ideal neutron detection effciency for thermal neutrons. The present work is focused on characterizing optical properties of this semiconducting boron carbide material as a step in further development of the material for neutron detection and other applications.

Semiconducting boron carbide films were grown on silicon substrates using plasma enhanced chemical vapor deposition and their optical properties were characterized using variable angle spectroscopic ellipsometry over a wide spectral range, from mid-infrared to vacuum-ultraviolet wavelengths. The effects of deposition substrate temperature and of post-deposition heat treatments on …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Semi-Automatic Image Segmentation For Volumetric Visualization Of Pelvis Ct Scan-Images, Suprijanto Suprijanto, Farida I. Muchtadi, Irwan Setiawan

Makara Journal of Technology

Semi-Automatic Image Segmentation for Volumetric Visualization of Pelvis CT Scan-Images. The current development of computerized tomography (CT) has enable us to obtain cross sectional image using multi slicing techniques in an order of few seconds. The obtained images represent several tissue structures on cross section slice being imaged. One challenge to help diagnosis using CT images is extracting an anatomic structure of interest using a method of image segmentation and volumetric visualization with the assistance of computers. In case of volumetric visualization of pelvis bones extracted from multi-slice CT images, whole images which are containing part of pelvis bone structures …

Implementation Of Six Sigma Method To Maintain The Quality Of Construction Projects, Yusuf Latief, Retyaning Puji Utami

Makara Journal of Technology

Implementation of Six Sigma Method to Maintain The Quality of Construction Projects. Six sigma (6-sigma) is a method that widely developed in the world, especially in manufacturing industry to decrease failures in achieving good quality in construction projects. The objective of this research is to explore the existing condition of quality management and the aplication of 6-sigma method in maintaining quality of construction projects. Structured interviews to experienced experts and people who were recommended by their companies were conducted. Non-parametric analysis using frequencies distribution procedures were used for analysis. The result shows that existing condition in quality management of construction …

Mechanical Properties Of Ramie Fiber Reinforced Epoxy Lamina Composite For Socket Prosthesis, Tresna P. Soemardi, Widjajalaksmi Kusumaningsih, Agustinus Purna Irawan

Makara Journal of Technology

Mechanical properties of ramie fiber reinforced epoxy lamina composite for socket prosthesis. This paper presents an investigation into the application of natural fiber composite especially ramie fiber reinforced epoxy lamina composite for socket prosthesis. The research focuses on the tensile and shear strength from ramie fiber reinforced epoxy lamina composite which will be applied as alternative material for socket prosthesis. The research based on American Society for Testing Material (ASTM) standard D 3039/D 3039M for tensile strength and ASTM D 4255/D 4255M-83 for shear strength. The ramie fiber applied is a fiber continue 100 % Ne14'S with Epoxy Resin Bakelite …

Potency Of Thermoelectric Generator For Hybrid Vehicle, Nandy Putra, Raldi Artono Koestoer, Mohammad Adhitya, Ardian Roekettino, Bayu Trianto

Makara Journal of Technology

Potency of Thermoelectric Generator for Hybrid Vehicle. Thermoelectric Generator (TEG) has been known as electricity generation for many years. If the temperature difference occurred between two difference semi conductor materials, the current will flow in the material and produced difference voltage. This principle is known as Seebeck effect that is the opposite of Peltier effect Thermoelectric Cooling (TEC). This research was conducted to test the potential of electric source from twelve peltier modules. Then, these thermoelectric generators were applied in hybrid car by using waste heat from the combustion engine. The experiment has been conducted with variations of peltier module …

Effects Of Ph On Calcium Carbonate Precipitation Under Magnetic Field, Nelson Saksono, Yuliusman Yuliusman, Setijo Bismo, Roekmijati W. Soemantojo, Azwar Manaf

Makara Journal of Technology

Magnetic field effect on CaCO3 precipitation is the key parameter in evaluating the effectiveness of Anti-scale Magnetic Treatment (AMT). The purpose of this study was to investigate magnetic fields influence on CaCO3 precipitation in high and low super-saturated CaCO3 solution by varied pH CaCO3 solution using circulation flow fluid system. The observation results in the high super saturated solution (pH 8.5) showed the increase of precipited CaCO3 in magnetized solutions compared to those in non-magnetic solution during circulation process. In the low super-saturated CaCO3 solution (pH 6.4) it was found that magnetic treatment increased CaCO3 precipitation after circulation process. In …

Performance Of Hollow Fiber Membrane Gas-Liquid Contactors To Absorb Co2 Using Diethanolamine (Dea) As A Solvent, Sutrasno Kartohardjono, Pan Ade Nata, Eko Prasetio, Yuliusman Yuliusman

Makara Journal of Technology

This study uses DEA solution to absorb CO2 from the gas flow through the hollow fiber membrane contactors. This study aims to evaluate the performance of hollow fiber membrane contactors to absorb CO2 gas using DEA solution as solvent through mass transfer and hydrodynamics studies. The use of DEA solution is to reduce the mass transfer resistance in the liquid phase, and on the other side, the large contact area of the membrane surface can cover the disadvantage of membrane contactors; additional mass transfer resistance in the membrane phase. During experiments, CO2 feed flows through the fiber lumens, while the …

Intermetallic Cu3sn Phase Layer On Electrode’S Tip Of Galvanized Resistance Spot Welding, Muhammad Anis, Aulia Irsyadi, Deni Ferdian

Makara Journal of Technology

Intermetallic Cu3Sn Phase Layer on Electrode’s Tip of Galvanized Resistance Spot Welding. A resistance spot welding method is commonly used in automotive industries application. In a resistance spot welding method, the copper electrode has a significant role as an electric current carrier for joining thin metal sheet. This research was focused on studying the effect of tin layer at the electrode tip for joining galvanized steel sheet. The main variable of this research is in the thickness of the intermetallic Cu3Sn layer. The result showed that the introduction of tin layer less than 1 μm in thickness on the electrode …

Simple Ml Detector For Multiple Antennas Communication System, Ahmad Taqwa, Soegijardjo Soegijoko, Sugihartono Sugihartono, Suhartono Tjondronegoro

Makara Journal of Technology

Simple ML Detector for Multiple Antennas Communication System. In order to support providing broadband wireless communication services against limited and expensive frequency bandwidth, we have to develop a bandwidth efficient system. Therefore, in this paper we propose a closed-loop MIMO (Multiple-Input-Multiple-Output) system using ML (Maximum Likelihood) detector to optimize capacity and to increase system performance. What is especially exciting about the benefits offered by MIMO is that a high capacity and performance can be attained without additional frequency-spectral resource. The grand scenario of this concept is the attained advantages of transformation matrices having capability to allocate transmitted signals power suit …

Technical Research Needs For Sustainable Buildings: Results From A Multidisciplinary Nsf Workshop, Leidy Klotz, Vivien Loftness, Gregor Henze, David J. Sailor, David Riley

Mechanical and Materials Engineering Faculty Publications and Presentations

This article describes research needs for sustainable buildings as defined in a July 2009 National Science Foundation-sponsored workshop. This workshop brought together building researchers with researchers in the areas of distributed renewable energy and multifunctional materials to engage their expertise and identify overlapping research needs and opportunities. An overview of sustainable building design provided the broad context for discussion. This overview was followed by focused presentations in building control systems, advanced building envelopes, and systems and process integration. In addition, presentations on distributed renewable energy and multi-functional materials supported the participants in outlining and generating research needs that connect the …

Shear Rate Threshold For The Boundary Slip In Dense Polymer Films, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The shear rate dependence of the slip length in thin polymer films confined between atomically flat surfaces is investigated by molecular dynamics simulations. The polymer melt is described by the bead-spring model of linear flexible chains. We found that at low shear rates the velocity profiles acquire a pronounced curvature near the wall and the absolute value of the negative slip length is approximately equal to thickness of the viscous interfacial layer. At higher shear rates, the velocity profiles become linear and the slip length increases rapidly as a function of shear rate. The gradual transition from no-slip to steady-state …

Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger

Other Nanotechnology Publications

The interplay between local mechanical strain energy and lateral frictional forces determines the shape of carbon nanotubes on substrates. In turn, because of its nanometer-size diameter, the shape of a carbon nanotube strongly influences its local electronic, chemical, and mechanical properties. Few, if any, methods exist for resolving the strain energy and static frictional forces along the length of a deformed nanotube supported on a substrate. We present a method using nonlinear elastic rod theory in which we compute the flexural strain energy and static frictional forces along the length of single walled carbon nanotubes (SWCNTs) manipulated into various shapes …

Doppler Broadening Analysis Of Steel Specimens Using Accelerator Based In Situ Pair Production, V. Makarashvili, Douglas P. Wells, Ajit K. Roy

Mechanical Engineering Faculty Research

Positron Annihilation Spectroscopy (PAS) techniques can be utilized as a sensitive probe of defects in materials. Studying these microscopic defects is very important for a number of industries in order to predict material failure or structural integrity. We have been developing gamma‐induced pair‐production techniques to produce positrons in thick samples ( ∼4–40 g/cm2, or ∼0.5–5 cm in steel). These techniques are called ‘Accelerator‐based Gamma‐induced Positron Annihilation Spectroscopy’ (AG‐PAS). We have begun testing the capabilities of this technique for imaging of defect densities in thick structural materials. As a first step, a linear accelerator (LINAC) was employed to produce photon beams …

Functionally Graded Materials By Laser Metal Deposition, Syamala Rani Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metal-working techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Evaluation Of Direct Diode Laser Deposited Stainless Steel 316l On 4340 Steel Substrate For Aircraft Landing Gear Application, Tian Fu, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Zhiqiang Fan, Syamala Rani Pulugurtha, Jianzhong Ruan, Hsin-Nan Chou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

300M steel is used extensively for aircraft landing gears because of its high strength, ductility and toughness. However, like other high-strength steels, 300M steel is vulnerable to corrosion fatigue and stress corrosion cracking, which can lead to catastrophic consequences in the landing gear. Stainless steels offer a combination of corrosion, wear, and fatigue properties. But for an aircraft landing gear application a higher surface hardness is required. A laser cladding process with fast heating and cooling rates can improve the surface hardness. AISI 4340 steel is used as a lower cost alternative to 300M due to its similar composition. In …

Increase Of Heat Transfer To Reduce Build Time In Rapid Freeze Prototyping, Ming-Chuan Leu, Sriram Praneeth Isanaka, Von Richards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Reduction of part build time in the Rapid Freeze Prototyping (RFP) process, which fabricates a 3D ice part layer-by-layer by depositing and freezing water droplets, has been achieved by increase of heat transfer. Three mechanisms have been experimentally investigated: 1) cooling the substrate, 2) use of forced convection, and 3) use of a chilling plate. Cooling the substrate is effective for parts of small heights but becomes ineffective with increase in part height. Forced convection produced desirable reduction in part build time but with the undesirable formation of frost on the built ice part. The use of chilling plate to …

Development Of A Low Cost Handheld Microfluidic Phosphate Colorimeter For Water Quality Analysis, Sean C. Kaylor

Master's Theses

This thesis describes the design, fabrication, and testing process for a microfluidic phosphate colorimeter utilized for water quality analysis. The device can be powered by, and interfaced for data collection with, a common cell phone or laptop to dramatically reduce costs. Unlike commercially available colorimeters, this device does not require the user to measure or mix sample and reagent. A disposable poly(dimethylsiloxane) (PDMS) microfluid chip, powered by an absorption pumping mechanism, was used to draw water samples, mix the sample at a specific ratio with a molybdovanadate reagent, and load both fluids into an onboard cuvette for colorimetric analysis. A …

Short-Term Failure Analysis Of Aluminum Conducting Composite Core Transmission Lines, Brian Burks

Electronic Theses and Dissertations

Recently the inefficiency and lack of capabilities of electric energy transmission have been put in the global spotlight; a transmission line design known as the Aluminum Conducting Composite Core Trapezoidal Wire (ACCC/TW^TM) attempts to eliminate the deficiencies. The ACCC core is comprised of a new hybrid composite material. The most probable causes of short-term damage to the ACCC core were investigated through a series of finite element models. It was found that excessive bending was the most likely cause of short-term damage to the core. During bending of the ACCC core, stresses are concentrated at the interface in …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Numerical/Experimental Investigation Of Plunge Stage And Effect Of Donor Material In Friction Stir Welding, Saptarshi Mandal

Mechanical & Aerospace Engineering Theses & Dissertations

Friction Stir Welding (FSW) was developed in 1991 as a robust solid-state joining technique that uses a specially shaped rotating tool to generate heat and plasticize material around the tool. The tool then mixes plasticized material along the joint line to produce the weld. Over the last decade, FSW has become increasingly popular for welding aluminum. The combination of attractive properties of the weld and cost-efficiency has led researchers to investigate the feasibility of using FSW for steel. One of the major impediments for using friction stir welding for harder materials such as steel is tool wear. It is well-documented …

The Effective Slip Length And Vortex Formation In Laminar Flow Over A Rough Surface, Anoosheh Niavarani, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The flow of viscous incompressible fluid over a periodically corrugated surface is investigated numerically by solving the Navier–Stokes equation with the local slip and no-slip boundary conditions. We consider the effective slip length which is defined with respect to the level of the mean height of the surface roughness. With increasing corrugation amplitude the effective no-slip boundary plane is shifted toward the bulk of the fluid, which implies a negative effective slip length. The analysis of the wall shear stress indicates that a flow circulation is developed in the grooves of the rough surface provided that the local boundary condition …