Materials Science and Engineering Commons^™

An Empirical Model For Build-Up Of Sodium And Calcium Ions In Small Scale Reverse Osmosis, Subriyer Nasir

Makara Journal of Technology

A simple models for predicting build-up of solute on membrane surface were formulated in this paper. The experiments were conducted with secondary effluent, groundwater and simulated feed water in small-scale of RO with capacity of 2000 L/d. Feed water used in the experiments contained varying concentrations of sodium, calcium, combined sodium and calcium. In order to study the effect of sodium and calcium ions on membrane performance, experiments with ground water and secondary effluent wastewater were also performed. Build-up of salts on the membrane surface was calculated by measuring concentrations of sodium and calcium ions in feed water permeate and …

The Effect Of Enzymatic Hydrolysis On The Properties Of Protein Hydrolysate From Paddy Mushroom, Niken Widya Palupi, Wiwik Siti Windrati, Tamtarini Tamtarini

Makara Journal of Technology

Protein hydrolysate was prepared from Paddy (Volvariella volvaceae) mushroom. Hydrolysis uses commercially protease available Protamex ™ with enzyme concentration of 0.1% (w/w). Hydrolysis was performed at three different temperatures (room temperature, 40 °C, and 50 °C) with different incubation periods (60, 90, and 120 minutes). Enzyme inactivation was done in 90 °C for 3 minutes. Yield and degree of hydrolysis ranged from 94.76% to 99.55% and 19.06% to 24.59%. Protein solubility was about 89–11,8%. The longer time of hydrolysis, the darker the color of protein hydrolysate. Protein hydrolysate which has hydrolysis at 50 °C for 120 minutes has the highest …

Effect Of Diafiltration On Preparation Of Fermented Mung Beans Concentrate As Probiotic Savory Flavor Through Ultrafiltration Membrane, Aspiyanto Aspiyanto, Agustine Susilowati

Makara Journal of Technology

Diafiltration by means of the ultrafiltration system of probiotic fermented Mung beans (Phaseolus radiatus L.) concentrate has been performed to reduce or eliminate salts and smaller impurities than the nominal cut-off of the membrane of 20,000 nominal weight cut-off (NWCO). These processes have been conducted as an attempt in order to get a probiotic product with organoleptic acceptability, composition, and the optimal total lactic acid bacteria (LAB) counts because the presence of salts will affect on the viability of LAB and the cell lysis of LAB and limit its utility in food products. Concentrate of probiotic mung beans was prepared …

Remote Sensing And Geographical Information System To Identify Drought Potency, Puguh Dwi Raharjo

Makara Journal of Technology

Remote Sensing and Geographical Information System to Identify Drought Potency. Kebumen regency was drought in year 2008, community clean water shortages and irrigation water following a decline in water resources. The use of remote sensing data and GIS can be used to identify the potential for drought-prone areas. Transformation of Landsat TM satellite imagery to obtain the brightness index, wetness index and vegetation index used to determine surface conditions in relation to drought. Brightness index and wetness index derived from the tasseled cap modifications, while the vegetation index derived from normalized difference vegetation index (NDVI) values. Other parameters such as …

High Pressure Adsorption Isotherm Of Co2 On Activated Carbon Using Volumetric Method, Awaludin Martin, Bambang Suryawan, Muhammad Idrus Alhamid, Nasruddin Nasruddin

Makara Journal of Technology

High Pressure Adsorption Isotherm of CO2 on Activated Carbon using Volumetric Method. Adsorption system is ones of the most effective methods for CO2 separating with other substances that produced from the burning of fossil fuels. In the design for that application, beside of characteristics of porous material (adsorbent) data, CO2 adsorption data on the adsorbent (kinetic and thermodynamic) are also needed. The aim of this research is resulting isothermal adsorption data at pressures up to 3.5 MPa by indirect methods (volumetric method) at isothermal temperature of 300, 308, 318 and 338 K. Adsorbent that used in this research is activated …

Concept Design And Testing Of Multi-Nozzle Water Mist Fire Suppression System, Danardono A. Sumarsono, Yulianto S. Nugroho, Mariance Mariance, I Gede Wahyu W. Ariasa

Makara Journal of Technology

In this work a flexible design of multi-nozzle arrangement of water mist fire suppression system was studied. The source of fire was a 65 mm diameter cooking oil fire. An investigation on the impact of nozzle arrangement on the temperature profile of fires was conducted. The occurance of oil splash due to the application of water mist was also studied. The water mist systems developed in the present work can effectively extinguish cooking oil fires and prevented them from re-ignition. The spray angle, discharge pressure, and water flow rate were important factors to determine the effectiveness of water mist in …

The Stability Characteristics Of Sandbag Submerged Breakwater, Ferry Fatnanta, Widi Agoes Pratikto, Haryo Dwito Armono, Wahyudi Citrosiswoyo

Makara Journal of Technology

The Stability Characteristics of Sandbag Submerged Breakwater. Breakwater is one of coastal structures to overcome problems of abrasion. Due to difficulties in obtaining rock material at the coastal area. The using of sandbags as a breakwater provides advantages in utilizing local materials. A Sandbag has a smooth surface, so the internal shear forces are relatively small. According to these phenomena, the research for parameters that are expected to affect the stability of the sand bags. These parameters are a slope, shape and formation of sand bags. This experimental research conducted in two dimensional physical model and took place on the …

Static Hand Gesture Recognition Of Indonesian Sign Language System Based On Backpropagation Neural Networks, Farida Asriani, Hesti Susilawati

Makara Journal of Technology

Static Hand Gesture Recognition of Indonesian Sign Language System Based on Backpropagation Neural Networks. The main objective of this research is to perform pattern recognition of static hand gesture in Indonesian sign language. Basically, pattern recognition of static hand gesture in the form of image had three phases include: 1) segmentation of the image that will be recognizable form of the hands and face, 2) feature extraction and 3) pattern classification. In this research, we used images data of 15 classes of words static. Segmentation is performed using HSV with a threshold filter based on skin color. Feature extraction performed …

Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Tieshu Huang, Nikhil D. Doiphode, M. N. Rahaman, Ming-Chuan Leu, B. Sonny Bal, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

There is an increasing demand for synthetic scaffolds with the requisite biocompatibility, internal architecture, and mechanical properties for the bone repair and regeneration. In this work, scaffolds of a silicate bioactive glass (13-93) were prepared by a freeze extrusion fabrication (FEF) method and evaluated in vitro for potential applications in bone repair and regeneration. The process parameters for FEF production of scaffolds with the requisite microstructural characteristics, as well as the mechanical and cell culture response of the scaffolds were evaluated. After binder burnout and sintering (60 min at 700°C), the scaffolds consisted of a dense glass network with interpenetrating …

Optimization Of Selective Laser Sintering Process For Fabrication Of Zirconium Diboride Parts, Ming-Chuan Leu, Shashwatashish Pattnaik, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective Laser Sintering (SLS) was investigated to fabricate Zirconium Diboride (ZrB₂) parts for ultra-high temperature applications. Experiments were conducted to determine values of SLS process parameters (laser power, scan speed, line spacing, and layer thickness) that can be used to build ZrB₂ parts with high integrity and sharp geometrical features. A sacrificial plate with a proper number of layers (determined from experimentation) separated from the main part was built in order to reduce thermal gradients when building the main part. The sacrificial plate was found to assist in eliminating cracks in the bottom of the main part. …

Selective Laser Sintering Of 13-93 Bioactive Glass, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Bioactive glasses are more promising than biopolymers in fabricating scaffolds for bone tissue repair because they convert to hydroxyapatite, when implanted in vivo. Both direct and indirect selective laser sintering (SLS) methods of 13-93 bioactive glass were considered in this research to study the feasibility of fabricating scaffolds for bone repair applications. Stearic acid was used as the binder in the indirect method to fabricate the scaffolds. The green scaffolds underwent binder burnout and sintering at various soaking conditions between 675⁰C and 700⁰C, achieving a maximum compressive strength of 23.6 MPa, which is higher than that of the human cancellous …

Computer Aided Contour Profiling Of High Strength Deposits, Sriram Praneeth Isanaka, Amar Bala Sridhar, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing processes suffer from the effect of ripples, edge rounding and surface variations. To reduce their effect, ideal process parameters for the laser deposition process were investigated. Also, a new method was identified to analyze deposits by accurately plotting their contours. This was achieved through point cloud data of the deposits generated using coordinate measurement and 3D scanning. Curve fitting was performed on the data in Matlab to generate the contours of the deposit. The intercept values, heights, and contact angle of the curves give an indication of the uniformity of deposits and aid in reducing defects.

Structural And Magnetic Properties Of Neodymium–Iron–Boron Clusters, Jeremy J. Anderson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Using inert gas condensation techniques the properties of sputtered neodymium-iron-born clusters were investigated. A D.C. magnetron sputtering source created vaporous Nd-Fe-B which was then condensed into clusters and deposited onto silicon substrates. A composite target of Nd-Fe-B discs on an iron plate and a composite target of Nd-(Fe-Co)-B were utilized to create clusters. The clusters were coated with a carbon layer through R.F. sputtering to prevent oxidation.

Samples were investigated in the TEM and showed a size distribution with an average particle diameter of 8.11 nm. The clusters, upon deposition, were amorphous as indicated by diffuse diffraction patterns obtained through …

Irrigation Leak Detection: Using Flow Rate Sensors To Detect Breaks In An Irrigation System, Adam Openshaw, Kalvin Vu

Computer Engineering

This report details the exploration and invention of a mechanism that can detect breaks in an irrigation system. With the ultimate goal of conserving water, we have designed an inexpensive, self sustaining flow rate monitor that can be used to identify anomalies in an irrigation system and wirelessly communicate the status of the system to a base station. Our implementation can also determine the direction of the anomaly based on the nature of the anomaly itself. This means that multiple monitors can be used to pinpoint the location of a break within the system in addition to merely detecting its …

Mechanical Behavior Of Alloy 230 At Temperatures Relevant To Ngnp Program, Sudin Chatterjee

UNLV Theses, Dissertations, Professional Papers, and Capstones

Identification and selection of suitable structural materials for heat exchanger application within the purview of the next generation nuclear plant (NGNP) program constitute a major challenge. This challenge stems from the lack of many desired metallurgical and mechanical properties of conventional metallic materials and alloys for applications at temperatures approaching 950 oC. Nickel (Ni)-base Alloy 230 has been highly recommended as a suitable structural material for such application due to its excellent resistance to high-temperature plastic deformation and superior corrosion resistance in many hostile environments. Systematic studies on tensile, fracture toughness, creep, stress-rupture and creep-fatigue behavior of this alloy have …

In-Pile Thermal Conductivity Measurement Methods For Nuclear Fuels, Brandon S. Fox

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Measuring nuclear fuel thermal conductivity in-pile can provide much needed data for understanding fuel performance during irradiation and yield thermophysical property data needed for simulation codes and fuel databases. The objective of this research is to develop and compare two in-pile thermal conductivity methods in a laboratory setting using surrogate fuel materials.

A steady-state radial heat flow method was investigated to understand its viability as an in-pile steady-state thermal conductivity technique. By using Joule heating to simulate volumetric heat generation within a surrogate fuel rod, thermal conductivity was measured with two thermocouples at different radial positions within the rod. Examinations …

Hydrogen Fuel Cell Analysis: Lessons Learned From Stationary Power Generation Final Report, Scott E. Grasman, John W. Sheffield, Fatih Dogan, Sunggyu Lee, Umit O. Koylu, Angie Rolufs

Materials Science and Engineering Faculty Research & Creative Works

This study considered opportunities for hydrogen in stationary applications in order to make recommendations related to RD&D strategies that incorporate lessons learned and best practices from relevant national and international stationary power efforts, as well as cost and environmental modeling of pathways. The study analyzed the different strategies utilized in power generation systems and identified the different challenges and opportunities for producing and using hydrogen as an energy carrier. Specific objectives included both a synopsis/critical analysis of lessons learned from previous stationary power programs and recommendations for a strategy for hydrogen infrastructure deployment. This strategy incorporates all hydrogen pathways and …

A Simple Technique For Surface Area Determination Through Supercritical Co2 Adsorption, Mahmud Sudibandriyo

Makara Journal of Technology

The measurement of specific surface area of porous materials has long been important in physical sciences and is currently growing in importance in applied and environmental science. Numerous systems have been developed for surface area measurement by gas adsorption. Commercial systems are available which can measure a wide range of absolute surface area with relative ease. However, their cost is often prohibitive. In this study, an inexpensive apparatus for surface area measurement has been set up to be used for measuring supercritical adsorption of CO2. The Ono-Kondo Lattice model was used to represent the adsorption isotherm and to determine the …

Fishing Catch And Catch Rate Assesment Of Mini Trawl, Trapnet And Setnet Fisheries, Muhammad Firdaus

Makara Journal of Technology

Fishing Catch and Catch Rate Assesment of Mini Trawl, Trapnet and Setnet Fisheries. This paper is aimed at assessing fishing catch and catch rate of the dragged gear on shrimp, trapnet, and setnet fisheries in Tarakan. The catch and effort data (number and species) and the fishing time of captured units were used in this qualitative analysis of fishing catch and catch rate to describe catch composition and catch rate from three catch fishery units in Tarakan. The result of the research shows that in the catching operation the dragged gear on shrimp has two main catch targets, which are …

Ontology-Based Automatic Classification For News Articles In Indonesian Language, Prajna Wira Basnur, Dana Indra Sensuse

Makara Journal of Technology

Ontology-Based Automatic Classification for News Articles in Indonesian Language. Searching specific information will be difficult if relying only on query. Choosing less specific queries will result in a lot of irrelevant information fetched by the system. One of the most successful ways to overcome this problem is to perform document classification based on the topic. There are many methods that can be used to conduct such a classification, such as using statistical and machine learning approaches. However, those document classification methods require training the data or learning the documents. In this study, the authors attempted to classify documents using a …

Particle Filter With Binary Gaussian Weighting And Support Vector Machine For Human Pose Interpretation, Indah Agustien, Muhammad Rahmat Widyanto, Sukmawati Nur Endah, Tarzan Basaruddin

Makara Journal of Technology

This paper proposes human pose interpretation using particle filter (PF) with Binary Gaussian Weighting and support vector machine (SVM). In the proposed system, particle filter is used to track a human object, then this human object is skeletonized using thinning algorithm and classified using SVM. The classification is to identify human pose, whether it is normal or abnormal behavior. Here particle filter is modified through weight calculation using Gaussian distribution to reduce the computational time. The modified particle filter consists of four main phases. First, particles are generated to predict target’s location. Second, the weight of certain particles is calculated …

Maintenance Activity Planning By Reability Centered Maintenance Ii Method, Rachmad Hidayat, Nachnul Ansori, Ali Imron

Makara Journal of Technology

Maintenance Activity Planning by Reability Centered Maintenance II Method. This research discusses maintenance activity planning using the RCM II method to evaluate failure function risk on compresor screw. The calculation of maintenance time is performed by considering maintenance and repair costs. The risk evaluation result with RPN shows that the critical component that needs to get the main priority in applying maintenance on compresor screw is function disorder on timeworn piston and on the broken outgoing air sponge’s filter that receives RPN 45. The optimum maintenance time calculation is applied on components that undergo scheduled restoration and scheduled discard task …

Software Design Of Mobile Antenna For Auto Satellite Tracking Using Modem Correction And Elevation Azimuth Method, Djamhari Sirat, Muhamad Asvial, Arman Djohan Diponegoro, Himawan Sidharta

Makara Journal of Technology

Software Design of Mobile Antenna for Auto Satellite Tracking Using Modem Correction and Elevation Azimuth Method. Pointing accuracy is important in satellite communication. Because the satellite’s distance to the surface of the earth's satellite is so huge, 1 degree of pointing error will make the antenna unable to send data to satellites. To overcome this, the auto-tracking satellite controller is made. This system uses a microcontroller as the controller, with the GPS as the location indicator of the antenna, a digital compass as the beginning of antenna pointing direction, a rotary encoder as azimuth and elevation censor, and a modem …

Petroleum Degradation In Soil By Thermophilic Bacteria With Biopile Reactor, Astri Nugroho, Edison Effendi, Yulius Karonta

Makara Journal of Technology

Crude oil degradation has been carried out using biopile reactor in total petroleum hydrocarbon (TPH) concentration of 5%, 10% and 15%. The thermophilic microorganisms used from isolation result and identification are Aeromonas salmonicida, Bacillus pantothenticus, and Stenotrophomonas maltophilia. The biodegradation of biopile reactor is done by various concentrations of TPH, total plate count (TPC), and volatile suspended solid (VSS) per day for 30 days. The biodegradation of kinetic parameter calculated consists of μ, μm, Y, Yt, Yobs, Kd, Ks from TPH concentration decision, and TPC and VSS in every microorganism with t (observation time) of 0 hour to 168 hours. …

Ergonomic Analysis Of Ui’S Bicyclesusing Posture Evaluation Index (Pei) Method In Virtual Environment, Erlinda Muslim, Boy Nurtjahyo, Zulkarnain Zulkarnain, Liza Afrinotha

Makara Journal of Technology

Ergonomic Analysis of UI’s Bicycles Using Posture Evaluation Index (PEI) Method in Virtual Environment. This research was conducted to study the ergonomic aspect of University of Indonesia’s bicycles in virtual environment. Software Jack 6.0 was used to analyze it. PEI was used as an approach that integrated the results of three methods: lower back analysis (LBA), ovako working posture analysis (OWAS), and rapid upper limb assessment (RULA). The research objective is to evaluate the existing design of University of Indonesia’s bicycles and to determine the most ergonomic redesign which concerns handlebar height and saddle height modification. The result showed that …

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational presentation for senior physics majors

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational/Research presentation for senior physics majors

Slip Boundary Conditions For The Moving Contact Line In Molecular Dynamics And Continuum Simulations, Nikolai V. Priezjev, Anoosheh Niavarani

Mechanical and Materials Engineering Faculty Publications

The problem of the moving contact line between two immiscible fluids on a smooth surface is revisited using molecular dynamics (MD) and continuum simulations. In MD simulations a finite slip is allowed by choosing incommensurate wall-fluid densities and weak wall-fluid interaction energies. The shear stresses and velocity fields are extracted carefully in the bulk fluid region as well as near the moving contact line. In agreement with previous studies, we found slowly decaying partial slip region away from the contact line. In steady-state shear flows we extract the friction coefficient along the liquid-solid interface, the local slip length, and the …

Functionally Graded Materials By Laser Metal Deposition (Preprint), Syamala R. Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metalworking techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Modeling The Combined Effect Of Surface Roughness And Shear Rate On Slip Flow Of Simple Fluids, Nikolai V. Priezjev, Anoosheh Niavarani

Mechanical and Materials Engineering Faculty Publications

Molecular dynamics (MD) and continuum simulations are carried out to investigate the influence of shear rate and surface roughness on slip flow of a Newtonian fluid. For weak wall-fluid interaction energy, the nonlinear shear-rate dependence of the intrinsic slip length in the flow over an atomically flat surface is computed by MD simulations. We describe laminar flow away from a curved boundary by means of the effective slip length defined with respect to the mean height of the surface roughness. Both the magnitude of the effective slip length and the slope of its rate-dependence are significantly reduced in the presence …