Materials Science and Engineering Commons^™

Thermal Barrier Coatings (Tbc's) For High Heat Flux Thrust Chambers, Christopher Michael Bradley

Open Access Theses & Dissertations

The last 30 years materials engineers have been under continual pressure to develop materials with a greater temperature potential or to produce configurations that can be effectively cooled or otherwise protected at elevated temperature conditions. Turbines and thrust chambers produce some of the harshest service conditions for materials which lead to the challenges engineers face in order to increase the efficiencies of current technologies due to the energy crisis that the world is facing. The key tasks for the future of gas turbines are to increase overall efficiencies to meet energy demands of a growing world population and reduce the …

New Topics On Nanoindentation Of Polymers And Composite Materials, Ricardo Martinez-Hernandez

Open Access Theses & Dissertations

In this study, nanoindentation was used to determine Young's modulus of homogeneous plastic materials as well as inhomogeneous epoxy woven fabric composites using various indenters. In the first part, homogeneous PMMA and polycarbonate were characterized using conical and spherical indenters. The conventional approach of the inverse analysis was modified in order to account for effects obtained during spherical nanoindentation. The experimental results were verified using FEA analysis in ABAQUS. It was found that viscous effects were present in conical nanoindentations which led to an overestimation of contact stiffness. The second part, the response of carbon and glass fiber woven fabric …

Analytical And Numerical Modeling Of Assembly Procedures Of Steel Fulcra Of Bascule Bridges, Sriharsha Garapati

USF Tampa Graduate Theses and Dissertations

To model shrink-fitting in metal components, an analytical model for two long compound cylinders with temperature dependent material properties and interference between them is developed for calculating transient temperatures and stresses. A finite element model is developed for the same geometry which incorporated the temperature dependent material properties. A convergence study is performed on the finite element and analytical model. The finite element model is validated by comparing the approximations of finite element model with the analytical solution.

In an assembly procedure of fulcrums for bascule bridges, called AP1, the trunnion is shrink-fitted into a hub, followed by shrink fitting …

High Performance Low Temperature Solid Oxide Fuel Cells With Novel Electrode Architecture, Yu Chen, Qian Liu, Zhibin Yang, Fanglin Chen, Minfang Han

Faculty Publications

In this study, we have fabricated high performance low temperature solid oxide fuel cells (LT-SOFCs) with both acicular anodes and cathodes with thin Gd-doped ceria (GDC) electrolyte film. The acicular Ni-Gd_0.1Ce_0.9O_2−δ (Ni-GDC) anode was prepared using freeze drying tape casting, while the hierarchically porous cathode with nano-size Sm_0.5Sr_0.5CoO₃ (SSC) particles covering an acicular GDC skeleton was prepared by a combination of freeze drying tape casting and self-rising approaches. The acicular electrodes with 5–200 μm pores/channels enhance mass transport, while SSC particles of about 50 nm in the cathode promote …

Effects Of Crossflow Velocity And Transmembrane Pressure On Microfiltration Of Oil-In-Water Emulsions, Nikolai V. Priezjev, Tohid Darvishzadeh

Mechanical and Materials Engineering Faculty Publications

This study addresses the issue of oil removal from water using hydrophilic porous membranes. The effective separation of oil-in-water dispersions involves high flux of water through the membrane and, at the same time, high rejection rate of the oil phase. The effects of transmembrane pressure and crossflow velocity on rejection of oil droplets and thin oil films by pores of different cross-section are investigated numerically by solving the Navier-Stokes equation. We found that in the absence of crossflow, the critical transmembrane pressure, which is required for the oil droplet entry into a circular pore of a given surface hydrophilicity, agrees …

Analysis Of Solid Oxide Fuel Cell-Gas-Turbine Hybrid System Technology For Use In Aircraft, Jeremy Milliner, Rory Roberts

Explorations – The Journal of Undergraduate Research, Scholarship and Creativity at Wright State

Solid oxide fuel-cell-gas-turbine (SOFC/GT) hybrid systems are a technology that provides a more efficient source of energy for a variety of uses. One potential use is to provide more efficient energy to aircraft, which is the subject of this work. Potential applications to aircraft and results from a computer model of a SOFC/GT are presented here.

An Experimental Investigation On The Trailing Edge Cooling Of Turbine Blades, Zifeng Yang, Hui Hu

Mechanical and Materials Engineering Faculty Publications

An experimental study was conducted to quantify the flow characteristics of the wall jets pertinent to trailing edge cooling of turbine blades. A high-resolution stereoscopic particle image velocimetry (PIV) system was used to conduct detailed flow field measurements to quantitatively visualize the evolution of the unsteady vortices and turbulent flow structures in the cooling wall jet streams and to quantify the dynamic mixing process between the cooling jet stream and the mainstream flows. The detailed flow field measurements were correlated with the adiabatic cooling effectiveness maps measured by using pressure sensitive paint (PSP) technique to elucidate underlying physics in order …

Silica Nanoparticle-Based Coatings With Superhydrophilic And Superhydrophobic Properties, Robert Andrew Fleming

Graduate Theses and Dissertations

Superhydrophilic and superhydrophobic surfaces have potential for implementation into a variety of fields, including self-cleaning surfaces, anti-fogging transparent materials, and biomedical applications. In this study, sandblasting, oxygen plasma treatments, silica nanoparticle films, and a low surface energy fluorocarbon film were employed to change the natural surface wettability of titanium, glass, and polyethylene terephthalate (PET) substrates, with an aim to produce superhydrophilic and superhydrophobic behavior. The effects of these surface modifications are characterized by water contact angles (WCAs), surface wetting stability, surface morphology and roughness, surface elemental composition, and optical transmittance measurements. The results show that stable superhydrophilic and superhydrophobic surfaces …

Design, Fabrication, Testing Of Cnt Based Isfet And Characterization Of Nano/Bio Materials Using Afm, Zhuxin Dong

Graduate Theses and Dissertations

A combination of Carbon Nanotubes (CNTs) and Ion Selective Field Effect Transistor (ISFET) is designed and experimentally verified in order to develop the next generation ion concentration sensing system. Micro Electro-Mechanical System (MEMS) fabrication techniques, such as photolithography, diffusion, evaporation, lift-off, packaging, etc., are required in the fabrication of the CNT-ISFET structure on p-type silicon wafers. In addition, Atomic Force Microscopy (AFM) based surface nanomachining is investigated and used for creating nanochannels on silicon surfaces. Since AFM based nanomanipulation and nanomachining is highly controllable, nanochannels are precisely scratched in the area between the source and drain of the FET where …

Plasma Test On Industrial Diamond Powder In Hydrogen And Air For Fracture Strength Study, Rohit Asuri Sudharshana Asuri Sudharshana Chary

UNLV Theses, Dissertations, Professional Papers, and Capstones

Diamonds are the most precious material all over the world. Ever since their discovery, the desire for natural diamonds has been great; recently, the demand has steeply increased, leading to scarcity. For example, in 2010, diamonds worth $50 billion were marketed. This increased demand has led to discovering alternative sources to replace diamonds. The diamond, being the hardest material on earth, could be replaced with no other material except another diamond. Thus, the industrial or synthetic diamond was invented. Because of extreme hardness is one of diamond's properties, diamonds are used in cutting operations. The fracture strength of diamond is …

Physico-Chemical, And Sensory Properties Of Soy Based Gouda Cheese Analog Made From Different Concentration Of Fat, Sodium Citrate And Various Cheese Starter Cultures, Abu Amar, Ingrid Suryanti Surono

Makara Journal of Technology

Gouda cheese analog (GCA) was made using soy protein isolate (SPI), skim milk powder (SMP), fat (palm fat and butter fat), and water (W) at optimal ratio of SPI : SMP : F : W = 14 : 6 : 20 : 60. The effects of butter fat, sodium citrate, and cheese starter culture on the sensory properties of ripened product were assessed by preference test, hedonic test, and the texture profile analysis (TPA) of GCA. The free fatty acids, water-soluble nitrogen, and reduction in pH value of progel were also measured. The use of 100% butter fat (BF) produced …

Effects Of Deposition Parameters And Oxygen Addition On Properties Of Sputtered Indium Tin Oxide Films, Badrul Munir, Rachmat Adhi Wibowo, Kim Kyoo Ho

Makara Journal of Technology

Indium tin oxide (ITO) films were sputtered on corning glass substrate. Oxygen admixture and sputtering deposition parameters were optimized to obtain the highest transparency as well as lowest resistivity. Structural, electrical and optical properties of the films were then examined. Increasing deposition rate and film thickness changed the crystallographic orientation from (222) to (400) and (440), as well as higher surface roughness. It was necessary to apply substrate heating during reposition to get films with better crystallinity. The lowest resistivity of 5.36 x 10-4 Ω•cm was obtained at 750 nm film thickness. The films’ resistivity was increased by addition of …

The Effect Of Rubber Mixing Process On The Curing Characteristics Of Natural Rubber, Abu Hasan, Rochmadi Rochmadi, Hary Sulistyo, Suharto Honggokusumo

Makara Journal of Technology

This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously …

Observation Of Center Disaster Damage On Pariaman And Wasior Using Differential Sar Interferometry (Dinsar), Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

This study focuses on disaster observations in Pariaman (West Sumatera) and Wasior (Papua) using remote sensing techniques (differential SAR interferometry). Differential interferometry (DInSAR) method was performed on two PALSAR data sets with different acquisition months, i.e. about a month after and before disaster, respectively. The center damage of Pariaman earthquake and Wasior flood can be determined by deriving Land Subsidence using DInSAR method.

Coastal Physical Vulnerability Of Surabaya And Its Surrounding Area To Sea Level Rise, Sayidah Sulma, Eko Kusratmoko, Ratna Saraswati

Makara Journal of Technology

The study for coastal vulnerability to sea level rise was carried out in Surabaya and its surrounding area, it has focused on calculations of the physical vulnerability index were used coastal vulnerability index (CVI) methods. It was standardized by the multi criteria analysis (MCA) approach according to the study area. The score of each physical variable derived from remote sensing satellite data and the results of studies that have been done, such as modeling results and thematic maps, and then integrated into geographic information systems (GIS). Result of this study shows that the coastal areas of Gresik, Surabaya, and Sidoarjo …

The Effect Of Size And Crumb Rubber Composition As A Filler With Compatibilizer Pp-G-Ma In Polypropylene Blends And Sir-20 Compound On Mechanical And Thermal Properties, Erna Frida

Makara Journal of Technology

Having been researched the development of thermoplastic elastomer material of polypropylene and natural rubber SIR- 20 compound with Crumb Rubber as the filler. Reinforced polypropylene with size 60 mesh with 1 mm, and the composition of the Crumb rubber (30, 40, and 50) wt%. Observed mechanical properties are tensile strength, fracture elongation, Young's modulus, tear strength and impact strength. Thermal properties are analyzed by DSC and DTA/TGA. It is acquired that for the size of 60 mesh crumb rubber tensile strength, fracture elongation, Young’s modulus, tear strength and impact strength are bigger than 1mm size. The addition of 60 mesh …

Development Of Local-Economic-Development Small And Medium Industries (Led-Sme) In East Java, Rachmad Hidayat, Sabarudin Akhmad

Makara Journal of Technology

This paper presents the effects of Indonesian government’s developmental efforts of assistance and training performed on the growth of LED-SME business units and business performance. Both parameters of the government’s assistance and training were used to analyze the impact to the growth and performance of business unit. To achieve a comprehensive result, samples acquired in this research were about 190 entrepreneurs and managers of LED-SME from East Java. Based on the parameters above, there are five hypotheses made to prove the relationship of the assistance and training to the growth and performance of business units. The structural equation modeling (SEM) …

Cdm Potential In Palm Solid Waste Cogeneration As An Alternative Energy In Aceh Province, Mahidin Mahidin, Izarul Machdar, Muhammad Faisal, Muhammad Nizar

Makara Journal of Technology

Empty Fruit Bunch (EFB) as a solid waste in Crude Palm Oil (CPO) industry does not utilized yet as an alternative energy source to generate electricity. It is well known that use of solid wate (biomass) as an energy source is part of the Clean Development Mechanism (CDM) scheme due to direct reduction of Green House Gases (GHGs) emission and provide a direct contribution to sustainable development. Utilization of EFB as a source of energy is very potential to be implemented in Aceh since this province has 25 CPO Mills at the moment which actively produce about 870,000 ton EFB …

Small Scale Experiment: Thermal Performance Comparison Between Fiber-Cement Roof And Photovoltaic Roof In Malang, Indonesia, Nurhamdoko Bonifacius, Sri Nastiti Nugrahani Ekasiwi

Makara Journal of Technology

Irradiation on the surface of photovoltaic module heats up the photovoltaic module itself and the room underneath the roof of integrated photovoltaic building in the tropics area. Room heating reduces thermal condition and photovoltaic module surface heating reduces its performance in generating electricity. This paper discusses an experiment of measuring the surface temperature of photovoltaic modules and fiber-cement roof surface as a comparison. This experiment also measures the impact of rising temperatures in each space underneath. It used small-scale mock-ups exposed to direct sunlight. The result of the experiment shows that photovoltaic roof surface temperature is lower than fiber-cement roof …

Improved Optical Probe For Measuring Phytoplankton Suspension Concentrations Based On Optical Fluoresensce And Absorption, Retno Wigajatri Purnamaningsih, Nining Betawati Prihantini

Makara Journal of Technology

This paper discusses the results of improved optical probe that works according to optical fluorescence and absorption phenomena for measuring the phytoplankton suspension concentrations. Measurements are made on the Scenedesmus sp. culture. The laboratory test has shown that range of concentration from 104 up to around 1 x 106 cells/mL; fluorescence intensity at λ = 685 nm; and logarithmic of transmission intensity at λ = 405 nm are proportional to the cell concentration linear with proportional constant γ = 4 × 10-5 and β = –2 × 10-7 mL/cell respectively.

Mechanical And Thermal Properties Of Polypropylene Reinforced By Calcined And Uncalcined Zeolite, Nurdin Bukit

Makara Journal of Technology

This study was carried out to compare mechanical and thermal properties of polypropylene (PP) reinforced with uncalcined and calcined zeolites. The PP samples were reinforced with zeolites at various quantities of 2, 4, and 6 (wt %). The comparison of the two types of zeolite was based on mechanical properties, including tensile strength, elongation at break, and Young’s modulus, and thermal characteristics analyzed using DSC, and DTA/TGA technique. The results obtained clearly revealed that both zeolites were able to significantly increase tensile strength and Young’s modulus of the samples, with calcined zeolite was found to work better. Addition of calcined …

Benchmark For Country-Level Earthquake Strong-Motion Instrumentation Program, Widjojo Adi Prakoso, I Nyoman Sukanta

Makara Journal of Technology

An empirical study to develop benchmark models at country-level to assess the suggested number of earthquake strongmotion stations based on a framework encompassing geographic, demographic, and socio-economic parameters is reported. The models are to provide a working estimate of the required number of stations for improving the strongmotion instrumentation program of Indonesia. National earthquake strong-motion networks of New Zealand, Japan, Taiwan, Iran, Turkey, and Italy were used as the references. The parameter proposed is the number of stations in land area of 1,000 km2, and three models based on the exponential regression analysis are presented as functions of population density, …

Worst Case Of Relative Disturbance Gain Array For Uncertain Distillation System, Rudy Agustriyanto, Jie Zhang

Makara Journal of Technology

This article discusses the constrained nonlinear optimization formulation for calculating the worst case of lower and upper bounds of relative disturbance gain array (RDGA) for uncertain process models. The proposed approach seeks the minimum and maximum values of the relative disturbance gains subject to the constraints in which the process and disturbance gains are within their uncertainty ranges. RDGA ranges are useful for control structure determination and the related robustness, as they provide information regarding the sensitivity to gain uncertainties. The proposed method is demonstrated by ternary distillation column case study. Closed loop simulation results support the analysis based on …

Biodiesel Production From Waste Cooking Oil Using Hydrodinamic Cavitation, Muhammad Dani Supardan, Satriana Satriana, Mahlinda Mahlinda

Makara Journal of Technology

The aim of this research was to study biodiesel production from low cost feedstock of waste cooking oil (WCO) using hydrodynamic cavitation apparatus. A two-step processes esterification process and transesterification process using hydrodynamic cavitation for the production of biodiesel from WCO is presented. The first step is acid-catalyzed esterification process for reducing free fatty acid (FFA) content of WCO and followed by base-catalyzed transesterification process for converting WCO to biodiesel as the second step. The result of esterification process with methanol to oil molar ratio of 5 and temperature of 60 oC showed that the initial acid value of WCO …

Knowledge Dictionary For Information Extraction On The Arabic Text Data, Wahyu Syaifullah Jauharis Saputra, Agus Zainal Arifin, Anny Yuniarti

Makara Journal of Technology

Information extraction is an early stage of a process of textual data analysis. Information extraction is required to get information from textual data that can be used for process analysis, such as classification and categorization. A textual data is strongly influenced by the language. Arabic is gaining a significant attention in many studies because Arabic language is very different from others, and in contrast to other languages, tools and research on the Arabic language is still lacking. The information extracted using the knowledge dictionary is a concept of expression. A knowledge dictionary is usually constructed manually by an expert and …

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Molecular Dynamics Simulations Of Oscillatory Couette Flows With Slip Boundary Conditions, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The effect of interfacial slip on steady-state and time-periodic flows of monatomic liquids is investigated using non-equilibrium molecular dynamics simulations. The fluid phase is confined between atomically smooth rigid walls, and the fluid flows are induced by moving one of the walls. In steady shear flows, the slip length increases almost linearly with shear rate. We found that the velocity profiles in oscillatory flows are well described by the Stokes flow solution with the slip length that depends on the local shear rate. Interestingly, the rate dependence of the slip length obtained in steady shear flows is recovered when the …

Freeze-Form Extrusion Fabrication Of Functionally Graded Material Composites Using Zirconium Carbide And Tungsten, Ang Li, Aaron S. Thornton, Bradley K. Deuser, Jeremy Lee Watts, Ming-Chuan Leu, Greg Hilmas, Robert G. Landers

Materials Science and Engineering Faculty Research & Creative Works

Ultra-high-temperature ceramics are being investigated for future use in aerospace applications due to their superior thermo-mechanical properties, as well as their oxidation resistance, at temperatures above 2000⁰C. However, their brittleness makes them susceptible to thermal shock failure. As graded composites, components fabricated as functionally-graded materials (FGMs) can combine the superior properties of ceramics with the toughness of an underlying refractory metal. This paper discusses the grading of two materials through the use of a Freeze-form Extrusion Fabrication (FEF) system to build FGM parts consisting of zirconium carbide (ZrC) and tungsten (W). Aqueous-based colloidal suspensions of ZrC and W were developed …

Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd

STAR Program Research Presentations

Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …

Fabrication And Characterization Of Biocomposites From Polylactic Acid And Bamboo Fibers, Sarah E. Royse

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Environmental concerns have been motivating research in the field of biodegradable materials, especially those from biological sources. Polylactic acid (PLA) is one biopolymer with the potential to replace some standard synthetic polymers. PLA is currently used for fibers, medical sutures, and some packaging, but is still used very little compared with synthetic polymers. One thing that can be done to expand the potential applications of PLA is to add fibers to create composite materials. Bamboo is a good choice for these fibers because it is abundant in many parts of the world, grows very quickly, and is widely unused. Composites …