Materials Science and Engineering Commons^™

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi_0.8-xAl_xCo_0.2O₂ (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi_0.71Al_0.09Co_0.2O₂ compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Diffusion Of Hydrogen At Iron Apply For Electrochemical Oscillating Permeation, Li Zhang, Ren-He Yin, Zhan-Mei Sun

Journal of Electrochemistry

The diffusion of hydrogen in iron was measured using electrochemical oscillating permeation. Through the samples in the different frequencies, it was found that diffusion of hydrogen at iron is of linear relation with boundary condition, which is the key to Fick's diffusion equation amplitude in the liquor. We can exploit this line relation getting the diffusion of hydrogen at iron.

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan

Journal of Electrochemistry

An all-vanadium redox flow storage battery possesses many advantages over conventional storage batteries.The development statue of two types electrode materials (metal and compound type) is introduced in this article.

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared. The amount of Nafion in a catalytic layer was optimized, and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy. For a MEA with both Pt 4 mg/cm² in the anode and the cathode, suitable Nafion loading was 21.4 wt% in the anode. With 21.4 wt% Nafion loading in the cathode, the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density. While, the DMFC performances came down, as Nafion loading increasing,for ohm and concentration polarization.

Electrochemical Properties Of Nitrate Immobilized On Gold Electrodes With 2-Aminoethanethiol Sams, Ya-Ru Song, Hong Wu, Hui-Bo Shao

Journal of Electrochemistry

Nitrate reductase (NR) and phospholipids were immobilized on gold electrodes with 2-aminoethanethio(AET) SAMs. After Au/AET/NR and Au/AET/NR/lipid were soaked in pH 7 phosphate buffers for days, a pair of pre-reversible peak appeared at around 0.202 V and 0.149 V respsctively, irregularly grew with soaking time in blank buffer.The cathodic peak current (i_pcl) of Au/AET/NR system had linear relationship with scan rate between 0.02 and 0.5 V⋅s^-1 ,while i_pcl was proportional to V^1/2 in Au/AET/NR/lipid system. The direct electron transfer of enzyme electrodes was strongly affected by pH. Compared with Au/AET, NR exhibited a higher electrochemical …

Modification Of Molybdenum Nitride Electrode For Supercapacitor(I)——The Effect Of Ammonium Vanadate On The Properties Of Molybdenum Nitride Electrode, Xue-Liang Li, Dao-Rong Luo, Hua-Lin Wang, Jian-Bo He, Yun-Guei Zhu

Journal of Electrochemistry

The effect of vanadium on the properties of the electrode of molybdenum nitride has been studied by using XRD, SEM and cyclic voltammetry. Modified molybdenum nitride was made as follow: films were coated by dipping titanium sheet in the solution containing different composition of molybdenum oxide, ammonium vanadate, ammonia, glycol and oxalic acid, and coated films are reacted with free ammonia. The results show that the specific capacitance of modified electrode was considerably increased and the operation voltage was broadened with the addition of ammonium vanadate in the dipping solution. The mechanism of these effects generated is the formation of …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report For May-June-July 2002, John Farley

Transmutation Sciences Materials (TRP)

The goal of this project is to understand the basic science of corrosion in the steel/LBE system.

We are taking more data, typically using the newly installed X-ray Photoelectron Spectrometry (XPS) apparatus, and analyzing our existing data. Undergraduate students Denise Parsons and Julia Manzerova have helped a great deal in the analysis of the data. We can obtain the elemental composition as a function of position within the sample. This gives clues to the migration of materials, the composition of the protective oxide layer, and the basic science of the corrosion process. We found dramatic differences between the exposed and …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems: Annual Progress Report (May 2001 – May 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. Further, the localized corrosion behavior of these alloys …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report 03/16/02- 06/15/02, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high oxygen concentration, …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Phase Two, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The proposed work will combine chemical kinetics and hydrodynamics in target and test-loop lead-bismuth eutectic (LBE) systems to model system corrosion effects. This approach will result in a predicative tool that can be validated with corrosion test data, used to systematically design tests and interpret the results, and provide guidance for optimization in LBE system designs. The task includes two subtasks. The first subtask is to try to develop the necessary predictive tools to be able to predict the levels of oxygen and corrosion products close to the boundary layer through the use of Computational Fluid Dynamics (CFD) modeling. The …

An Investigation On Sr-Doped Spinel Phase-LisrXMn2-XO4, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

Sr-doped spinel phase-LiSr_xMn_2-xO₄ was successfully prepared by solid-state method. Structural and electrochemical characterizations were carried out. Although Sr²⁺ has a large ion radius-1.12 , the spinel structure can be well maintained for LiSr_xMn_2-xO₄ sample as far as the x value doesn't surpass 0.05. Electrochemical study presents supporting evidence that doping the stoichiometric LiSr_xMn_2-xO₄ phase with Sr is an effective way to improve the cycleability of LiSr_xMn_2-xO₄ spinel material. A remarkable enhancement of the cycleability with retention of the initial …

Polishing Rate And Dependent Factors Of Copper In Nh3 ·H2O Aqueous Solution Containing K3Fe(Cn)6 During Cmp, Han-Wei He, Yue-Hua Hu, Ke-Long Huang

Journal of Electrochemistry

Dependence of polishing rates of copper on concentrations of NH₃·H₂O, passivator K₃[Fe(CN)₆], γ-Al₂O₃ abrasives and polishing pressures, polishing rotative rates were studied. Dependent mechanisms were explained. It was shown a linear relation between polishing and polishing pressures and rotative rates within some range, non-linear relation between polishing and various reagent concentrations. Preston coefficient was varied. CMP recipe of the best polishing rate was gained: 4%K₃Fe(CN)₆+1%NH₃·H₂O+25%γ-Al₂O₃, K_p=0.02383. Technics conditions were 300 rpm and 80 kpa. The …

Electrosynthesis Of Glyoxylic Acid In A Cooled Cathode Reactor, Jin-Hong Fan, Jun Li, Xue-Yun Chen, Wei Li, Hao-Qi Gao

Journal of Electrochemistry

Glyoxylic acid was produced by electroreduction of oxalic acid in a well designed cooled cathode reactor. The cathodic and anodic electrolytes were super-saturated oxalic acid and hydrochloric acid aqueous solutions separated by a super-acid ion-exchange membrane. The current efficiency and time-space yield of glyoxylic acid were studied under different temperatures of cathode and electrolyte, current densities, materials of cathode. With the cooled cathode reactor, the energy consumption was reduced and higher oxalic acid concentration was available in solution, so that current efficiency was improved. The results indicated that the average time-space yield of glyoxylic acid was about 0.032 kg·dm^{-3 …}

Self-Assembled Monolayer Of Schiff Bases On Au Electrode, Ke-Qiang Ding, Qing-Fei Wang, Zhen-Bin Jia, Na Tian, Ning Wang, Ru-Ting Tong, Xin-Kui Wang, Hui-Bo Shao

Journal of Electrochemistry

Schiff bases tailored with -SH group, was self-assembled on Au substrate for the first time. The packing degree of this monolayer was described with SEM technique. Spontaneously, the self-assembled monolayer (SAM) was briefly characterized with CV and EIS methods. Though Comparing with the SAM of alkanethiol, the membrane we fabricated was relatively loose, our work is the first step to study Schiff bases by means of self-assembled monolayer.

Development Of 200～500 W Portable Proton Exchange Membrane Fuel Cell Power System, Li-Qing Hu, Li-Rong Zhou, Zheng Li, Jian-Wei Xia, Ming-Zhu Fu, Xin Wu, Yun Zhu

Journal of Electrochemistry

The Properties of the Portable PEM Fuel Cell Power Source are very unique compared with the common primary or rechargeable electro-chemical battery. This paper describes the In this work, of the 200～500 W portable PEM fuel cell power system, was developed. The system mainly composed of four subsystem: 1)Fuel cell stack; 2)Air delivery; 3)Hydrogen source; 4)Heat dissipation and system control.

Corrosive Electrochemical Behavior Of Carbon Steel In Microbiological Medium, Jing Liu, Hong-Bo Fan, Hai-Ping Xu, Jia-Shen Zheng, Li-Ming Xu, Zong-Qiang Mao

Journal of Electrochemistry

Sulfate-reducing bacteria (SRB)grows and propagates, PH of the solution is dropped from 7.5 to 5.8, and forms the biofilms on carbon steel in culture medium. The micro-environment on the surface of carbon steel is changed under the biofilms, the factors accelerate the formation of the pitting corrosion. When the biofilm on carbon steel is cleaned out, the surface of carbon steel have the non-uniform pitting corrosion. The activity of SRB and the porous structure of biofilms induced the initiation and development of the pitting corrosion of carbon steel. The process of microbiologically induced corrosion (MIC) involves the development of SRB …

Effect Of Cl- On The Transition Current Density Of Zn During The Electrodeposition Of Zn-Ni Alloys, Ren-He Yin, Zheng-Hua Fang, Wei-Min Cao

Journal of Electrochemistry

There exists a transition current density of Zn when the normal co-deposition of Zn-Ni alloys at chloride baths turns to anomalous type. The value increases with Cl^- concentration, but is independent of pH, this is because the existence of Cl^- decreases the evolution overpotential of Ni metal and has a catalytic effect on it.

Electrocatalytic Oxidation Of Formaldehyde On The Proline Film Modified Electrode, Yu-Rong Ma, Qiu-Xia Yang, Guo-Bao Li, Zheng-Kai Xi, Xue-Lin Wang

Journal of Electrochemistry

The proline film modified electrode and its electrochemical behavior was studied by cyclic voltammetry and spectroelectrochemistry. After incorporation of Ni(Ⅱ), the cyclic voltammograms of the proline Ni(Ⅱ) film electrode exhibited a typical redox peak, which appeared at potential of 0.52 V anodic and 0.44 V cathodic in NaOH. The formal potentials E' were linearly dependent on the pH, and the peak currents ip were linearly dependent on the square root of the scan rates, thus charge transfer in the film was controlled by diffusion. The diffusion coefficient is figured out to be 2×10^_-10 cm²·s^-1. The …

Preparation,Structure And Properties Of Electrochromic Rhodium Oxide Films, Hai-Hong Wang, Tao Wang, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

Electrochromic rhodium oxide films were prepared on ITO substrate by sol-gel method. The films exhibited reversible two-color (bright yellow at reduction and dark green at oxidation) electrochromic behavior in alkaline solution with good cycle stability. In-situ XRD, TGA-DTA, IR, XPS methods were used for studying the structure and chemical process of the films. The diffusion coefficient during the electrochromic process was measured by electrochemical impedance spectra method. It was found that the rhodium oxide films may be suitable for the use in electrochromic devices.

Studies On Sulfate Reducing Bacteria Influenced Corrosion Of 90/10 Cu/Ni Alloy, Guang-Zhou Liu, Jian-Hua Qian, Yan Ma, Jian-Hua Wu

Journal of Electrochemistry

Electrochemical techniques such as measurements of corrosion potential,the polarization resistance, and potentiodynamic scanning technique were used to investigate the electrochemical behavior of 90/10 Cu/Ni alloy in Postgate C medium containing sulfate reducing bacteria(SRB). The results showed that the corrosion potential of the alloy changed from -0.20 to -0.75 V(SCE) when bacteria inocula was added, and the polarization resistance R_p decreased obviously, which corresponds to an increased corrosion rate. The shape ofthe anodic polarization curves was drastically changed in the presence of SRB, and an active-passive transition was observed. Electron probe microanalyzer was used to investigate the morphology and chemical …

Recent Developments In The Electrolyte For Lic6/Electrolyte/Cathode Battery, Cui-Ying Wang, Sheng-Liang Zhao, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

We present a reviewed the development and status of electrolyte for LiC 6/electrolyte/cathode battery. The effect of the salt, solvent, additive and impurity on the conductivity of the electrolyte, formation of the solid-electrolyte-interphase (SEI) and cycle life of the battery were described.

Syntheses And Photoluminescence Of Zinc Oxide Polyaniline Coaxial Nanowires And Their Array, Zhi-Xin Zheng, Yan-Yan Xi, Ping Dong, Huai-Guo Huang, Jian-Zhang Zhou, Lin-Lin Wu, Zhong-Hua Lin

Journal of Electrochemistry

A novel nanomaterial, zinc oxide (ZnO) and polyaniline (PANI) coaxial nanowires and their array in the template, was synthesized using anodic aluminum oxide (AAO) membrane as template. The morphology of these coaxial nanowires was observed with transmission electron microscope (TEM). The experiments on photoluminescence (PL) of coaxial nanowires and their array in AAO membrane show that the visible emission band of ZnO shifts from 530 nm to 400 nm and the luminescence is enhanced for the coaxial nanowires array in AAO membrane,and the visible emission band shifts to a lower wavelergth (385 nm) for coatial nanowires in NaOH solution. Possible …

Electrochemical Properties Of Mixed Metal Oxide Coated Titanium Anodes In Seawater, Ting-Yong Wang, Li-Kun Xu, Guang-Zhang Chen

Journal of Electrochemistry

Mixed metal oxide coated titanium anodes prepared by thermal decomposition were characterized by scanning electron microscopy and electrochemical measurement, while the consumption rate of an anode was also measured in seawater. In order to examine the practical performances of mixed metal oxide-coated anodes, a simulating test on floating dock in seawater has also been carried out. The SEM results indicate that oxide layers exhibited a cracked-mud morphology which endows the anode with good electrocatalytic activity. The electrochemical measurements showed that mixed metal oxide-coated anodes exhibit excellent electrochemical activity and electrochemical stability in seawater. Owing to good corrosion resistance and low …

A Blend Conducting Membranes For Direct Methanol Fuel Cells, Lei Li, Jun Zhang, Hong Wu, Yu-Xin Wang

Journal of Electrochemistry

An attempt was made to modify membranes for direct methanol fuel cells by blending Nafion or polystyrene sulfonic acid (PSSA) with polyvinylidene fluoride (PVDF) from their solutions. The proton conductivity and methanol barrier property as a function of the membrane compositions are discussed. Compared with the Nafion 117 membrane, the PVDF-Nafion blend membranes with 25 wt% of Nafion showed a decrease in the conductivity by about 2 orders of magnitude, and the methanol barrier properties increased about 3 orders of magnitude. If the ratio (σ/P) is adopted to characterize the performance of the membrane, the PVDF-PSSA and PVDF-Nafiion blend membranes …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (December 1, 2001 – February 28, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including HT- 9, EP 823 and 422. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these alloys will be evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. The extent and morphology of cracking of these alloys will further be evaluated …

Third Quarter Report, Covering January Through March 2002, John Farley

Transmutation Sciences Materials (TRP)

Progress from June 2001-November 2001 was presented at the winter meeting of the American Nuclear Society in Reno (November 12-15, 2001), and incorporated into a refereed conference proceeding. A copy of the refereed conference proceeding has been provided to Tony Hechanova. In brief, the paper described the new program to examine the corrosive effects of lead-bismuth eutectic (LBE) on steels. We employed various types of surface studies (Scanning Electron Microscope [SEM], and X-ray Photoelectron Spectrometry [XPS]) to examine steel samples that had been exposed to LBE for various lengths of time at various temperatures. The goal is to understand the …

The Determination Of The Best Modified Way And Microscopical Analysis For Enzyme/Immunoelectrodes, Sa-Ying Dong, Hong-Ren Wang, Yu-Zhu Gao, Guang-Zhang Chen, Ming-Xiang Lv, Bo-Yi Tian

Journal of Electrochemistry

In this paper, the electrochemical response characteristics of enzyme and immuno electrodes were studied by cyclic voltammetry under different conditions. Our goals were to determine the best modified way of bioelectrode, which was the base of biosensor's application. 30U GOD and 0.8 mg/mL SEC1 antibody were suitable to bioelectrode preparation and detection. The microscopical analysis was finished with scan microscopy.

Study On The Orthogonal Test Of Al-Substituted α-Ni(Oh)2 Prepared By Complexation-Precipitation Method, Hui Chen, Jian-Ming Wang, Tao Pan, Hui-Ming Xiao, Jian-Qing Zhang

Journal of Electrochemistry

Al-substituted α-Ni(OH)₂ was prepared by a complexation-precipitation method and characterized by XRD.The electrochemical performance was tested by the charge-discharge method. The experimental results of orthogonal test showed that the effect order of some key preparative conditions on the electrochemical performance of Al-substituted α-Ni(OH)₂ was the concentration of aqueous ammonia, the content of aluminum and pH value.The optimum prepareative conditions for obtaining the sample with maximum specific discharge capacity (304 mAh·g^-1) were 0.5 mol·L^-1 aqueous ammonia, 15 mol% Al content and pH 11.0.

Preliminary Study On Direct Ethanol Fuel Cell, Shu-Qin Song, Li-Kang Chen, Jian-Guo Liu, Zhao-Bin Wei, Qin Xin

Journal of Electrochemistry

The performance of a direct ethanol fuel cell based on Nafion115 was reported.PtRu/C and Pt/C were used as ethanol anode and oxygen cathode catalysts in a single cell of size 9 cm² .The effects of temperature, oxygen pressure, the flow rate of ethanol, and oxygen, and ethanol concentration were tentatively studied. The experimental results showed that the cell open circuit voltage 0.608 V, the cell voltage 0.329 V at 50 mA/cm², and the peak power density 19.25 mW/cm² were reached under the conditions of T_cell =85 ℃, P_O2 =0.5 MPa, C_ethanol =1.0 mol/L …

Photocurrent Enhancement By Ticl4 Post-Treatment For Tio2 Nanoporous Film Electrode, Yan-Jie Ren, Li Zhang, Sheng-Min Cai

Journal of Electrochemistry

Enhanced photocurrent in dye-sensitized photoelectrochemical cell was obtained by post-treating the TiO₂ nanoporous film electrode with TiCl₄. By investigating the effect of the post-treatment on surface area, pore size distribution, laser pulse induced current transient of the film electrode, photocurrent increase by the post-treatment was assigned to the improved electron percolation resulting from broadening of interparticle neck.