Mechanics of Materials Commons^™

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Reuse Of Calcium Carbonate (Caco3) Recovered From Discarded Carpets As Filler In Fiber-Reinforced Polymer (Frp) Composites, Roshan Devkota

Graduate Theses, Dissertations, and Problem Reports (ETD)

Over four billion pounds of carpet are discarded annually in the United States, making carpet waste a significant environmental concern. Calcium carbonate (CaCo₃) constitutes up to 45% of the mass of most synthetic carpets. Reusing this CaCo₃ as a filler in the rapidly growing fiber-reinforced polymer (FRP) industry, which is projected to reach USD 10.38 billion, presents a low-cost, practical approach to developing a market-based solution to post-consumer carpet waste.

This study investigates the reuse of CaCo₃ recovered from discarded carpet backing as a filler in FRP composites, focusing on its mechanical viability in comparison to virgin CaCo₃. The methodology …

Pulsed Arc Additive Manufacturing Of A Functionally Graded Er2209 Duplex Stainless Steel And Hsla-100 Structure: Morphology, Characterization, And Mechanical Performance, Stevens G. Hill Jr

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process well suited to the efficient production of large structures. Duplex stainless steel exhibits high corrosion resistance and good strength which can be highly beneficial for industrial use. However, its use is limited due to its cost and complexity in controlling microstructure to achieve desired properties. In many cases, it can be highly beneficial to manufacture a component which uses specialty steel grades such as duplex stainless steel only where necessary, and utilizes more affordable, commonly available steels for reinforcement or bulk structural support. A functionally graded material satisfies these requirements by providing a …

Deep-Learning Based Microstructure Reconstruction And Generation, Cameron J. Maloney, Lucas Taliaferro

College of Engineering Summer Undergraduate Research Program

Characterizing the microstructural behavior of materials is crucial for understanding their properties and performance. Traditional imaging methods, such as optical microscopy and electron microscopy, are effective but costly and time-consuming. Computational approaches can reduce costs and time while expanding the accessibility of microstructural analysis through the generation of new microstructure images. Traditional computational approaches, namely descriptor-based approaches, are slow but effective in low-data scenarios. Modern approaches use machine learning (ML), which is faster but often requires a lot of data to approach the performance of descriptor-based methods. This research leverages a special data-efficient Generative Adversarial Network (GAN) architecture to artificially …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

A First Step Towards Understanding Thermomechanical Behavior Of The Nb-Cr System Through Interatomic Potential Development And Molecular Dynamics Simulations, Lucas A. Heaton, Adib J. Samin

Faculty Publications

Utilizing a preliminary interatomic potential, this work represents an initial exploration into the thermomechanical behavior of NbCr solid solutions. Specifically, it examines the effect of different amounts of Cr solute, for which information in the literature is limited. The employed interatomic potential was developed according to the embedded atom model (EAM), and was trained on data derived from density functional theory calculations. While the potential demonstrated reasonable accuracy and predictive power when tested, various results highlight deficiencies and encourage further development and training. Mechanical strength, heat capacities, thermal expansion coefficients, and thermal conductivities were found to decrease with Cr content. …

Micro-Mechanical Characterization Of Uhpc Stiffness Mechanisms: Towards A Better Understanding Of Concrete Elastic Modulus, Charissa N. Puttbach

Graduate Theses and Dissertations

Current design code equations for estimating the elastic modulus of specialty concretes like ultra-high performance concrete are not all suitable. Developing empirical curves from exhaustive experimental testing is challenging for concretes that may have high levels of cement replacement with mineral admixtures and fibers at varying volume contents. As such, an alternative approach is taken that seeks to understand the constituent microscale stiffness mechanisms and relate the results to the macroscale. Micropillars are fabricated on several cement paste phases using a focused ion beam. A modified pico-indenter is used to determine the linear and non-linear behavior under micro-compression loading. Micropillar …

Numerical Simulation Of Laser Induced Elastic Waves In Response To Short And Ultrashort Laser Pulses., Alireza Zarei

All Dissertations

In an era of intensified market competition, the demand for cost-effective, high-quality, high-performance, and reliable products continues to rise. Meeting this demand necessitates the mass production of premium products through the integration of cutting-edge technologies and advanced materials while ensuring their integrity and safety. In this context, Nondestructive Testing (NDT) techniques emerge as indispensable tools for guaranteeing the integrity, reliability, and safety of products across diverse industries.

Various NDT techniques, including ultrasonic testing, computed tomography, thermography, and acoustic emissions, have long served as cornerstones for inspecting materials and structures. Among these, ultrasonic testing stands out as the most prevalent method, …

Improved Ballistic Impact Resistance Of Nanofibrillar Cellulose Films With Discontinuous Fibrous Bouligand Architecture, Colby Caviness

All Theses

Natural protective materials offer unparalleled solutions for impact-resistant material designs that are simultaneously lightweight, strong, and tough. Particularly, the dactyl club of mantis shrimp features chitin nanofibrils organized in a Bouligand structure, which has been shown to effectively dissipate high-impact energy during powerful strikes. The mollusk shells also achieve excellent mechanical strength, toughness, and impact resistance with a staggered, layer-by-layer structure. Previous studies have shown that hybrid designs, by combining different bioinspired microstructures, can lead to enhanced mechanical strength and energy dissipation capabilities. Nevertheless, it remains unknown whether combining Bouligand and staggered structures in nanofibrillar cellulose (NFC) films, forming a …

A Manufacturing-To-Response Pathway For Manufacturing Optimization Of Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Dissertations

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Insights Into The Characterization And Degradation Of Electrospun Polycaprolactone Scaffolds For Tissue Engineering Applications, Caleb B. Wells

Theses and Dissertations

Electrospun polymeric biodegradable scaffolds are essential in tissue engineering, particularly for Engineered Tissue Vascular Grafts (ETVGs), which promise advancements in treating coronary artery disease, peripheral arterial disease, congenital cardiovascular defects, and renal disease. These scaffolds present a solution to issues with autologous graft availability and durability. While large-diameter grafts in low-pressure environments have seen success, small-diameter grafts in high-flow scenarios remain challenging. Understanding polymeric scaffold degradation and behavior during incubation, especially under dynamic mechanical loading, is vital for clinical translation of small-caliber ETVGs.

This research focuses on characterizing the mechanical and microstructural properties of electrospun polycaprolactone (PCL) scaffolds and their …

Inherently Porous Metal Structures With Sufficient Mechanical Properties Through Direct Writing Of Bio-Based Inks, Havva Eda Aysal

Graduate Theses, Dissertations, and Problem Reports (ETD)

There is currently a burgeoning interest in developing 3D printed metal structures with inherent porosity and sufficient mechanical properties for mass customization in the biomedical field. Current approaches for 3D printing of biocompatible metals rely on powder-bed fusion methods which are energy intensive and utilize large amounts of metal powder that is challenging to recycle. In addition, such methods aim on producing dense parts and porosity generation, within the printed part, is challenging due to the complex physics of the melting pool. Here, a relatively new and promising approach is undertaken to study the 3D printing of inherently porous structures …

Machine Learning For Electronic Structure Prediction, Shashank Pathrudkar

Dissertations, Master's Theses and Master's Reports

Kohn-Sham density functional theory is the work horse of computational material science research. The core of Kohn-Sham density functional theory, the Kohn-Sham equations, output charge density, energy levels and wavefunctions. In principle, the electron density can be used to obtain several other properties of interest including total potential energy of the system, atomic forces, binding energies and electric constants. In this work we present machine learning models designed to bypass the Kohn-Sham equations by directly predicting electron density. Two distinct models were developed: one tailored to predict electron density for quasi one-dimensional materials under strain, while the other is applicable …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Experimental Characterization And Quantification Of Deformation Behavior In A Porous Carbon Fiber Network, Robert N Quammen

Theses and Dissertations--Chemical and Materials Engineering

Due to their wide range of attractive functional properties (such as low thermal conductivity and low density) porous materials are utilized in a variety of applications. In order to characterize these properties and others, the intrinsically heterogeneous microstructures of these materials need to be taken into account. These microstructures result in interactions across multiple length scales spanning several orders of magnitude. This makes the creation of robust computational models and straight-forward predictions of mechanical properties difficult for porous materials. With this in mind, this dissertation aims to provide experimental mechanical and deformation information spanning the length scales of interest for …

Investigating The Role Of Tesserae In Energy Absorption In Shark Cartilage, Molly Dobrow

UNF Graduate Theses and Dissertations

Unlike mammals, shark endoskeletons are composed of cartilage, which is less stiff compared to bone. Despite this structural disadvantage, sharks have risen to become apex predators, with reported maximum posterior bite force estimates approximating 5914 N in bull sharks. Shark jaws are estimated to undergo high cycle loading within the organism’s lifecycle without evidence of failure. Fatigue resistance may relate to mineral distribution within a component of the endoskeletal system – tesserae. Tesserae are thin, roughly hexagonal tiles composed of calcium phosphate hydroxyapatite (HA) crystals and grow by accretion to eventually surround the hyaline cartilage core. Though tesserae dimensions are …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Investigating The Rheological Behavior Of A Simple Yield Stress Fluid Under Shear Flows, Francesco Accetta

Theses

Many soft materials display unique and complex rheological behavior characterized by a transition from a solid-like to a fluid-like state upon the application of a force that exceeds the threshold to flow, known as the yield stress. Yield stress fluids are found in a wide range of commonly encountered materials including microgels, emulsions, and foams, and have been widely studied by rheologists over the last several decades. Carbopol is a popular polymeric microgel system as it displays simple, non-thixotropic rheological behavior and is typically seen as an ideal yield stress fluid. Previous research has demonstrated the reproducible behavior of shear …

Influence Of Forming Forces On Torsional, Tensile, And Compressive Deformation Of Paperboard Packages, Arvo Niini, Panu Tanninen, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Paperboard packages were tested mechanically to investigate influence of forming forces on torsional, tensile, and compressive deformation. The packages were paperboard trays which were press formed with different pressing forces and blank holder forces. Deformation of the trays was observed with torsion, compression, and tensile tests. A statistical analysis of test results was conducted to derive optimal forming forces. Increased pressing force yielded desirable deformation characteristics with the trays. Blank holder force had largest impact on the compressive deformation. Interaction of the pressing force and the blank holder force influenced the torsional and the compressive deformation. The optimal forming forces …

Double Cantilever Beam Mode-I Testing Validation In Large-Scale Additive Manufacturing Carbon Composite, Luis Alfonso Camacho

Open Access Theses & Dissertations

Testing for mechanical properties for additive manufacturing has been based on already existing standards for traditional manufacturing methods. For composites in large scale additive manufacturing there is a research gap in bond strength and fracture toughness for a single layer interface. By using Double cantilever beam Mode I, this thesis manuscript validates testing parameters and protocols to describe the intricacies of ABS matrix 20 wt.% carbon filled composite, specifically on the layer-to-layer interface. Studies suggest that fracture toughness is sensitive to process parameters, like deflection speed and sharpened crack tip at the layer interface of BAAM 3D printed part and …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …