Engineering Mechanics Commons^™

Simulation And Measurement Of The Radiant Field Produced By Quartz Heating Systems, Travis Lee Turner

Mechanical & Aerospace Engineering Theses & Dissertations

A method is developed for predicting the radiant heat flux distribution produced by tungsten-filament tubular quartz heating systems with reflectors. The method is an application of Monte Carlo simulation, which takes the form of a ray tracing or random walk scheme. The method is applied to four systems of increasing complexity including; a single unreflected lamp, a single lamp with a flat reflector, a single lamp with a parabolic reflector, and up to six lamps in a six-lamp contoured reflector heating unit. The general methodology of the Monte Carlo method is discussed and applied to the simulation of thermal radiation. …

Finite Element Analysis Of Thermal Post-Buckling And Vibrations Of Thermally Buckled Composite Plates, Charles Clifton Gray

Mechanical & Aerospace Engineering Theses & Dissertations

The development of supersonic and hypersonic flight vehicles such as the High Speed Civil Transport and the National Aero-Space Plane has created an increased need for analysis of structures at very high temperatures. Bisplinghoff and Pian, Yang and Han, and Dokmeci and Boley have conducted experimental and analytical studies to determine the effect of elevated temperatures on the vibration characteristics of isotropic plates, Chen and Chen, and Meyers and Hyer have clone studies on thermal buckling and post-buckling of composite plates, respectively.

The thermal loads which will be imposed on the new high speed aircraft will be too great for …

The Effectiveness Of Viscoelastic Damping Treatments On A Flexible Manipulator Subjected To Torsional Loads, Leah L. Remias

Mechanical & Aerospace Engineering Theses & Dissertations

The advent of new technology has led to an increasing number of missions in space. The space shuttle Remote Manipulator System (RMS) is a lightweight flexible manipulator currently used in NASA space missions. The future role of the RMS and similar flexible manipulators may include in-space construction and assembly tasks. Because these tasks require precise motion and short settling time of the end-point oscillations, effective vibration control schemes are being investigated.

Passive damping techniques have shown to provide a considerable amount of damping in controlling flexural vibrations. In this research passive damping via constrained viscoelastic damping treatments is explored as …

Finite Element Analysis Of Structures With Constrained Viscoelastic Layer Damping, Yung Chen

Mechanical & Aerospace Engineering Theses & Dissertations

It has been demonstrated that constrained viscoelastic layer damping treatments provide an effective means of passive control for structural vibration. These treatments dissipate vibrational energy by inducing shear strain in a thin layer of viscoelastic material. Our interest is in adding passive damping to a structure as an augmentation to active control. For such applications it is desirable to achieve high damping performance in a given frequency range with a minimum of added weight. Most damping treatments employ spatially continuous constraining layers over the entire viscoelastic layer. Plunkett and Lee have shown that the effectiveness of the damping treatment can …

Numerical Investigation Of A Non-Newtonian Material Through A Sudden Pipe Expansion, V. G. Masanja

Tanzania Journal of Engineering and Technology (TJET)

A numerical method for solving two dimensional elliptic boundary-value problems of fourth order is used for finding stationary solutions of the equations of motion for a laminar flow through a sudden pipe expansion of an incompressible non-Newtonian fluid with a constitutive equation of the Reiner-Rivlin (R-R) type. Results for the Newtonian fluid, which is a special case, are in excellent agreement with those by previous investigators and they demonstrate the reliability, superiority and accuracy of the method. Results for the non-Newtonian cases could be of value for fixing ideas about visco-elastic behaviour although the R-R fluid allows only inelasticity: this …

The Influence Of Payload Dynamics On Trajectory Tracking Performance Of Robot Manipulator, Atul G. Kelkar

Mechanical & Aerospace Engineering Theses & Dissertations

Future space mission plans call for extensive use of remote manipulator systems for tasks such as assembly of lunar vehicles or space station modules, servicing of satellites, etc. These tasks demand very high precision end-effector motion control. Methods for compensating manipulator dynamics to achieve better trajectory tracking performance have been investigated by many researchers. Still, it is not always clear whether the added complexity of dynamic compensation is warranted for a given system. As an aid in evaluating when dynamic compensation is required, this thesis presents a method for the determination of maximum endpoint tracking error due to uncompensated inertial …

A Systematic Procedure For The Analysis And Design Of Deployable Space Structures, Praveen Kumar

Mechanical & Aerospace Engineering Theses & Dissertations

An integrated graph theory and a symmetry-based approach have been developed for the type synthesis of deployable truss structures. Using this systematic approach, a bay of a deployable structure may be looked upon as being built around an axis or a plane of symmetry, including anti-symmetry. By providing a fictitious joint along this axis, the problem of structural design and analysis can be reduced to the study of one plane or face of the given structure. Each face is considered to be an assemblage of structural links connected by joints which form a closed kinematic chain. The conventional graph representation …

Eigensensitivity Analysis For Space Structures With Applications In Design Optimization, Sean Patrick Kenny

Mechanical & Aerospace Engineering Theses & Dissertations

Eigensensitivity analysis is concerned with the rates of changes of eigenvalues and eigenvectors with respect to design variables. Eigensolutions of space structures are found to display four distinct characteristics, three of which are related to various types of repeated eigenvalues. This study will address three cases of the real symmetric structural eigenvalue problem. The three cases that will be considered are: distinct eigenvalues, repeated eigenvalues with distinct first eigenvalue derivatives, and repeated eigenvalues with infinitely repeating eigenvalue derivatives. Analytic formulations for eigenvalue/ vector derivatives will be presented for each of the three cases. The directional differentiability of eigenvalues for the …

The Effects Of Bending On The Strain Distributions In A Stiffener-Skin Interface Region, Osvaldo F. Lopez

Mechanical & Aerospace Engineering Theses & Dissertations

An analytical and experimental study to assess the effect of bending on the adhesive strain distributions in a stiffener-skin interface region is described. A one-dimensional beam analysis is derived using a variational approach. Parametric studies are conducted to assess the effects of stiffener, skin, and adhesive thickness and adhesive material nonlinearity on the adhesive layer extensional and shear strain distributions subjected to applied bending. Two experimental methods of measuring through-the-thickness extensional strains in an adhesive are investigated. One method involves measuring the changes in the resistance of a composite strain sensor subjected to applied tension and compression loads. The second …

Application Of Shape Sensitivity Analysis For Computation Of Transient Free-Surface Flows, Frank Nicolas Michel

Mechanical & Aerospace Engineering Theses & Dissertations

Shape sensitivity analysis is introduced into a numerical scheme simulating a transient free-surface flow and applied to the case of a fluid advancing through a bed of cylinders. For this incompressible Newtonian flow, viscous forces are dominant. A penalty function finite element formulation is used to solve the problem. Coordinates of nodes on the moving boundary are chosen as design variables and an analytical formulation of the gradient of the finite element algebraic system, with respect to these variables, is derived.

In a numerical example, the results obtained with and without sensitivity analysis are compared. The efficiency and accuracy of …

Global/Local Stress Analysis Of Composite Structures, Jonathan B. Ransom

Mechanical & Aerospace Engineering Theses & Dissertations

A method for performing a global/local stress analysis is described and its capabilities are demonstrated. The method employs spline interpolation functions which satisfy the linear plate bending equation to determine displacements and rotations from a global model which are used as "boundary conditions" for the local model. Then, the local model is analyzed independent of the global model of the structure. This approach can be used to determine local, detailed stress states for specific structural regions using independent, refined local models which exploit information from less-refined global models. The method presented is not restricted to having a priori knowledge of …

Investigating The Method Of Structural Topological Variations For Sensitivity Analysis And Design Optimization, Niki A. Mehta

Mechanical & Aerospace Engineering Theses & Dissertations

The method of structural topological variations is a newly developed technique for analysis of frame structures. It provides a novel method that completely avoids formulating and solving simultaneous equations, required in the finite element displacement method. The principal objective of this thesis is to investigate the method of topological variations as a possible design tool and study its applicability in the sensitivity analysis and in the process of design optimization.

A computer code was developed for this method to obtain its comparative performance against the finite element displacement method. For analysis of large structures involving frequent local modifications, the method …

Explicit And Implicit Calculations Of Turbulent Cavity Flows With And Without Yaw Angle, Guan-Wei Yen

Mechanical & Aerospace Engineering Theses & Dissertations

Computations have been performed to simulate turbulent supersonic flows past three-dimensional deep cavities with and without yaw. Simulation of these self-sustained oscillatory flows have been generated through time accurate solutions of the Reynolds averaged complete Navier-Stokes equations using two different schemes: (1) MacCormack, finite-difference, (2) implicit, upwind, finite-volume schemes. The second scheme, which is approximately 30% faster, is found to produce better time accurate results. The Reynolds stresses have been modeled, using the Baldwin-Lomax algebraic turbulence model with certain modifications. The computational results include instantaneous and time averaged flow properties everywhere in the computational domain. Time series analyses have been …

A Reiner-Rivlin Fluid Flow Through Entrance Region Of A Circular Pipe, V. G. Masanja

Tanzania Journal of Engineering and Technology (TJET)

The flow of a Reiner-Rivlin fluid with two viscosity coefficients through the entrance region of a circular pipe has been studied numerically. In particular the growth of the entrance length as a function of the Reynolds number and the non-Newtonian parameters has been examined. Where comparison could be made, the results have been compared with existing experimental -and numerical data as well as the limited theoretical work available.

The Effects Of Nonlinearities On The Optimal Design Of Forced Vibrating Beams, Cheryl Celestine Jackson

Mechanical & Aerospace Engineering Theses & Dissertations

The optimal design of a beam under harmonic excitations is formulated and solved numerically for linear and nonlinear forced vibration theories. The beam has a nonuniform cross-sect ion, whose thickness can change during the optimization procedure. Based on the numerical results, for the given input frequency range, the linear vibration theory produces a more conservative design than the nonlinear vibration theory.

The analytical formulation for both theories is presented. For the linear case, a mean case is defined for the self-weight on a beam, and an alternating case is defined for input forcing frequencies which cause fatigue variations on a …

The Effect Of Elastic Boundary Conditions On The Dynamic Response Of Rectangular Plates, Terry K. Brewer

Mechanical & Aerospace Engineering Theses & Dissertations

Natural frequencies and forced steady-state harmonic response for the vibration of uniform rectangular plates with edges elastically restrained against rotation and transverse translation are addressed. A single mode Rayleigh-Ritz solution is derived using functions that describe the normal modes of vibration of a beam whose ends are elastically restrained. The finite element solution is obtained for comparison. MACSYMA symbolic manipulation system is implemented as an aid to the mathematical rigor of the Ritz approach and NASTRAN finite element code is used to model the mechanical system. Comparisons are made to published results and the solutions of this study are found …

Coupled Bending-Torsion Steady-State Response Of Pretwisted, Nonuniform Rotating Beams Using A Transfer-Matrix Method, Carl E. Gray Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Using the Newtonian method, the equations of motion are developed for the coupled bending-torsion steady-state response of beams rotating at constant angular velocity in a fixed plane. The resulting equations are valid to first order strain-displacement relationships for a long beam with all other nonlinear terms retained. In addition, the equations are valid for beams with the mass centroidal axis offset (eccentric) from the elastic axis, nonuniform mass and section properties, and variable twist. The solution of these coupled, nonlinear, nonhomogeneous, differential equations is obtained by modifying a Hunter linear second-order transfer-matrix solution procedure to solve the nonlinear differential equations …

Eigenvalue And Eigenvector Design Sensitivity Analysis For Nonlinear Beam Vibrations, Jian-Zhong Yuan

Mechanical & Aerospace Engineering Theses & Dissertations

A beam with immovable ends under large amplitude oscillations is axially subjected to an amplitude-dependent stretching force which is induced by the geometrical nonlinearity. The design sensitivity analysis for such a beam is investigated in this study.

Two variational formulations based on different approximations of nonlinear stretching force are studied firstly. The analytical equations of design sensitivity analysis for these nonlinear eigenproblems are then derived. Finally, a computational scheme using finite element method is developed to calculate the design sensitivity derivatives of the eigenvalue and eigenvector numerically. Numerical examples associated with the nonlinear eigenvalue and eigenvector analysis, as well as …

Structural Self-Shadowing And Its Effects On The Thermal-Structural Behavior Of Orbiting Trusses, Jack Mahaney

Mechanical & Aerospace Engineering Theses & Dissertations

The determination of structural shadowing is described. The computation of environmental heat loads for slender structural members in earth orbit is described, and two methods for finite element thermal analysis are described . The effects of self-shadowing on the thermal structural behavior of single truss members and two different trusses are presented. In each case the shadowing produces a noticeable effect on the temperature distributions on truss members, and on the deformations of the trusses.

Analysis And Optimal Design Of Wind Tunnel Balances, Sung-Ling Twu

Mechanical & Aerospace Engineering Theses & Dissertations

The problem of finding the optimal cross-sectional shape of the elastic cage in wind tunnel balance is formulated and solved numerically. A mathematical model to implement the boundary condition associated with the elastic rigid connection into the finite element method is discussed. Numerical results show that the rigid connection at the end of the elastic cage has significant effect on the stress distribution.

The finite dimensional approach for a three dimensional design sensitivity analysis is derived. Using both the free and rigid boundary conditions, numerical examples are performed and comparisons of the accuracy of design sensitivity analysis between the proposed …

Shape Optimization For Elastic Hollow Bars In Torsion, Jahau Lewis Chen

Mechanical & Aerospace Engineering Theses & Dissertations

The problem of finding optimal cross-sectional shapes of elastic hollow bars in torsion is formulated and solved numerically. A variational formulation for the state equation is presented, and the material derivative of continuum mechanics is used for the shape design sensitivity analysis. Performance criteria include the bending stiffness, the torsional rigidity, and the weight of the bar. The existence of a keyway, an example of geometric irregularity, can be considered as well. The material can be either isotropic or anisotropic. The finite element method is used for the numerical solution of the variational state equation and is integrated into an …

Design Of A Combustion System Simulating Waste Heat Recovery From Diesel Engine Exhaust Gases, Nikolaos Papadopoulos

Mechanical & Aerospace Engineering Theses & Dissertations

A forced-draft laboratory combustion system simulating diesel engine exhaust gas volume flow rate and temperature conditions for waste energy recovery is analyzed and discussed. The system consists of a fan which supplies the air. The slightly compressed air is then ducted through a combustor where it is heated, and then to an air-quencher where it is cooled to a desired temperature. Finally, the air is sent through a heat exchanger, after a diffuser process, for waste heat recovery.

A gas dynamic analysis has been performed for each component part as well as a parametric study via a computer program in …

Application Of Least-Squares Method To The Determination Of Orthotropic Elastic And Photoelastic Constants, R. G. Chermahini

Mechanical & Aerospace Engineering Theses & Dissertations

A least-squares technique is developed in matrix form to determine orthotropic elastic and photoelastic constants. Orthotropic elastic constants are determined by mounting strain gages on a half-plane specimen which is subjected to a compressive concentrated force. Strain values corresponding to a 1000 lb load and coordinates of the points where the gages are located are used as input data to the governing equation of orthotropic elasticity for the model under consideration. Orthotropic photoelastic constants are determined using a transparent composite half-plane model which is subjected to a concentrated load. Photoelastic constants are determined using the coordinates of selected point on …

Photoelastic Investigation Of Load Transfer In Eccentrically Loaded Single Lap Joints, Stephen Antrim Hann

Mechanical & Aerospace Engineering Theses & Dissertations

Photoelastic models of three eccentrically loaded single lap joints were analyzed. The adherends of each joint were identical and the bondlines differed in thickness and material properties. The adherends were analyzed for both cylindrical plate behavior and geometrical nonlinearity and the load transfer efficiency was examined. For all three models it was found that over 98% of the shank behaves as a cylindrical plate and that a geometrically nonlinear analysis yields bending stresses substantially lower than a linear analysis and that a relatively thick, low modulus bondline can increase load transfer efficiency.

An Apparatus For Measuring The Thermal Conductivity Of Cast Insulation Materials, Christine A. Wilkins, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

A steady-state apparatus has been developed for measuring the thermal conductivity of cast materials. The design has employed a novel thermal symmetry arrangement which can permit total electrical isolation of the test material from its surroundings. © 1980 American Institute of Physics

The Efficiency Of A Two-Edged Tool And Its Improvement, J. R. Masuha

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Steel Making In Port Talbot Works Of British Steel Corporation, S. P. Mosha

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Effect Of Compliant Wall Motion On Turbulent Boundary Layers, Dennis M. Bushness, Jerry N. Hefner, Robert L. Ash

Mechanical & Aerospace Engineering Faculty Publications

A critical analysis of available compliant wall data which indicated drag reduction under turbulent boundary layers is presented. Detailed structural dynamic calculations suggest that the surfaces responded in a resonant, rather than a compliant, manner. Alternate explanations are given for drag reductions observed in two classes of experiments: (1) flexible pipe flows and (2) water-backed membranes in air. Analysis indicates that the wall motion for the remaining data is typified by short wavelengths in agreement with the requirements of a possible compliant wall drag reduction mechanism recently suggested by Langley. Copyright © 1977 American Institute of Physics.

Forming Of 7075-T6 Aluminum In High Pressure Environments, Richard L. Pendleton, Robert L. Davis

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Plates of 7075-T6 Aluminum have been folded along a major axis in pressure environments of atmospheric, 20,000 psi, and 40,000 psi. A finite element computer program is used to determine the stress state in the plates at various loads. Tension and compression tests conducted in pressure environments up to 70,000 psi were used to construct models using effective stress, effective strain, and pressure as parameters to predict the behavior of the material under various stress conditions. A prediction of the occurrence of fracture in the folded plate was possible using the computer results and the pressure dependent model. As better …

Australian Tractor Test Report No. 58 : Massey-Ferguson 165, G H. Vasey, W. T. Brown

Journal of the Department of Agriculture, Western Australia, Series 4

THE Massey-Ferguson 165 is a general purpose farm tractor. The test tractor gave 50 drawbar h.p. with 59 h.p. at the P.T.O. at rated engine speed it comes within Class 5 of the Australian Standard Classification of Wheeled Tractors for Agricultural Purposes, AS Dl 0-1967. It is equipped with 18.4 x 28 in. pneumatic tyres. It has a threespeed gear box with a ratio change giving 6 forward and reverse speeds.