Signal Processing Commons^™

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

Hard Hat Ambient Liability Observer (Halo), Hunter Hykes, Nathan Kish, Brian Thomson

Williams Honors College, Honors Research Projects

Capturing workplace incident information is a growing area of concern for most companies. To assist with this, the design team proposed the H.A.L.O. This design uses time-of-flight sensors connected to LEDs to create a proximity-based hazard warning system. It also records incident data using an accelerometer and micro-SD card. This helps workers avoid some of the most common workplace injuries, slips, trips, and falls and accidental collisions.

Students have created a design with engineering, and marketing requirements that accomplish this task. The proposed design allows for this monitoring and mitigation systems to be attached to hard hats. Team members developed …

Light Loaded Automated Guided Vehicle, Marcus Radtka, Nazar Paramashchuk, Lawrence Shevock

Williams Honors College, Honors Research Projects

The objective of the locomotion system was to design and implement the mechanical, electrical, and software related functions to ensure the LLAGV had the capability of maneuvering its surroundings. The LLAGV’s motors were represented in an open loop transfer function to utilize RPM feedback and a compensator when needed. The modeled compensator helped control the LLAGV’s speed and acceleration, enabling further control of the LLAGV. The internal circuitry has the means to properly distributed power to all components and allowed the user to control the LLAGV to their desire. The application software within the LLAGV locomotion system (LLAGV-LS) had consideration …

Energy Considerations In Blockchain-Enabled Applications, Cesar Enrique Castellon Escobar

UNF Graduate Theses and Dissertations

Blockchain-powered smart systems deployed in different industrial applications promise operational efficiencies and improved yields, while mitigating significant cybersecurity risks pertaining to the main application. Associated tradeoffs between availability and security arise at implementation, however, triggered by the additional resources (e.g., memory, computation) required by each blockchain-enabled host. This thesis applies an energy-reducing algorithmic engineering technique for Merkle Tree root and Proof of Work calculations, two principal elements of blockchain computations, as a means to preserve the promised security benefits but with less compromise to system availability. Using pyRAPL, a python library to measure computational energy, we experiment with both the …

Cybersecurity Strategy Against Cyber Attacks Towards Smart Grids With Pvs, Fangyu Li, Maria Valero, Liang Zhao, Yousef Mahmoud

KSU Proceedings on Cybersecurity Education, Research and Practice

Cyber attacks threaten the security of distribution power grids, such as smart grids. The emerging renewable energy sources such as photovoltaics (PVs) with power electronics controllers introduce new potential vulnerabilities. Based on the electric waveform data measured by waveform sensors in the smart grids, we propose a novel cyber attack detection and identification approach. Firstly, we analyze the cyber attack impacts (including cyber attacks on the solar inverter causing unusual harmonics) on electric waveforms in distribution power grids. Then, we propose a novel deep learning based mechanism including attack detection and attack diagnosis. By leveraging the electric waveform sensor data …

Parallel And Asynchronous Distributed Optimization For Power Systems Operation, Ali Mohammadi

LSU Doctoral Dissertations

Distributed optimization approaches are gaining more attention for solving power systems energy management functions, such as optimal power flow (OPF). Preserving information privacy of autonomous control entities and being more scalable than centralized approaches are two primary reasons for developing distributed algorithms. Moreover, distributed/ decentralized algorithms potentially increase power systems reliability against failures of components or communication links.

In this dissertation, we propose multiple distributed optimization algorithms and convergence performance enhancement techniques to solve the OPF problem. We present a multi-level optimization algorithm, based on analytical target cascading, to formulate and solve a collaborative transmission and distribution OPF problem. This …

Learning Deep Architectures For Power Systems Operation And Analysis, Mahdi Khodayar

Electrical Engineering Theses and Dissertations

With the rapid increase in size and computational complexities of power systems, the need for powerful computational models to capture strong patterns from energy datasets is emerged. In this thesis, we provide a comprehensive review on recent advances in deep neural architectures that lead to significant improvements in classification and regression problems in the area of power engineering. Furthermore, we introduce our novel deep learning methodologies proposed for a large variety of applications in this area. First, we present the interval deep probabilistic modeling for wind speed forecasting. Incorporating the Rough Set Theory into deep neural networks, we create an …

Fault Location In Distribution System Based On Voltage Sag Analysis, Ahmad Muhamad Firdaus

Student Works (2020-2029)

Fault in the distribution system is something that cannot be avoided. It is a recurring event that occurs due to various factors such as natural occurrence, mechanism failure, or human error. All this contributes to the phenomenon that will affect the stability of the system and result in the loss of power to the consumers. However, such a fault is something that happens unexpectedly, and it is difficult to be eliminated. Therefore, various research work has been done over the years to overcome the problem. All research is done to find the most effective method of finding the fault location …

A Power Constrained 433-Mhz Low Noise Amplifier, Pablo Alvarez Arellano

Graduate Theses and Dissertations

Within wireless communication systems, low noise amplifiers are critical for the performance of receivers. They are primarily responsible for providing enough gain while adding little noise to overcome the noise of the subsequent stages. The LNA presented here is part of a battery-powered transceiver meant to measure crop nutrient data and relay the information. Therefore, power consumption and area become import considerations. To design for a specific power level, a power-constrained noise optimization method is used. The method sizes the amplifying transistor for a fixed source impedance, power dissipation, technology, and operating frequency. The chosen topology is the cascode stage …

Design And Development Of Fiber Bragg Grating Sensor For Detecting Of Hydrogen Gas In Transformer Oil, Mohd Raffi Samsudin

Student Works (2020-2029)

Hermetically sealed oil-immersed transformers are the key to electricity distribution networks. They are also one of the most expensive facilities in the electricity supply network. Immediate replacement is expected for this type of transformer upon failure because it is directly connected to the customer. Transformer oil acts as insulation, coolant and condition indicator. To date, there is no economical real-time monitoring system available to monitor the transformer oil condition. Therefore, there is a need to develop a cheap, non-intrusive and non-electrical sensor to monitor the health of the transformer by measuring the amount of dissolved hydrogen gas in oil, which …

A Silicon Germanium Cmos Linear Voltage Regulator For Wireless Agricultural Applications, Aminta Naidili Castillo Robles

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon germanium (SiGe) complementary metal-oxide-semiconductor (CMOS) linear regulator. The objective of the circuit is to power other analog devices regardless of the load current and input voltage changes. The application of this regulator is to be part of a project developing a miniaturized semiconductor platform that can be inserted into stems of crops in order to measure data inside the plant and then send it wirelessly to the user. The linear regulator was designed on a BiCMOS SiGe 0.13µm which is a GlobalFoundries process. It has been tested at …

Dynamic Voltage Rail Audio Amplifier, Evan Von Duhn, Timothy Oshatiouk, Slavisa Tosanovic, Andrew Cantrell

Williams Honors College, Honors Research Projects

The goal of this project is to create a high-quality, power-efficient audio amplifier. Most modern audio amplifiers use a constant amount of power regardless of the signal that is being amplified. This means that both loud and quiet portions of the audio signal require the same amount of power to amplify. The idea for this high-quality, power-efficient audio amplifier is that the quieter portions of the audio signal can be amplified using less power. This will be achieved by first analyzing the audio signal and controlling the power source based on the signal’s needs. Therefore, louder parts of the audio …

An Accurate And Efficient Time Delay Estimation Method Of Ultra-High Frequency Signals For Partial Discharge Localization In Substations, Pengfei Li, Kejie Dai, Tong Zhang, Yantao Jin, Yushun Liu, Yuan Liao

Electrical and Computer Engineering Faculty Publications

Partial discharge (PD) localization in substations based on the ultra-high frequency (UHF) method can be used to efficiently assess insulation conditions. Localization accuracy is affected by the accuracy of the time delay (TD) estimation, which is critical for PD localization in substations. A review of existing TD estimation methods indicates that there is a need to develop methods that are both accurate and computationally efficient. In this paper, a novel TD estimation method is proposed to improve both accuracy and efficiency. The TD is calculated using an improved cross-correlation algorithm based on full-wavefronts of array UHF signals, which are extracted …

Analog Sorting Using Pulse Width Modulation, Riley C. Olson

Computer Engineering

As time goes on, computers become more and more powerful. However, as processing time becomes less of a limiting factor for computing tasks, power consumption takes its place for many tasks. This paper proposes and tests a new method for sorting analog signals. This new sorting method converts analog signals into Pulse Width Modulated(PWM) signals of varying duty cycle , which are then sorted by a simple network of combinational logic, and then converted to a normal binary representation. In order to implement this new method, multiple circuits had to be designed and and tested to ensure their functionality and …

Bandwidth Analysis Of A Tightly-Packed Crossed-Dipole Array For Satellite Communications, Lawrence J. Lee

Theses and Dissertations

A bandwidth analysis of a tightly-packed crossed-dipole array antenna is presented in this thesis. A parametric study is described which varies the element spacing in the array and the resulting change in the terminal impedances is reported. The increased mutual coupling seen by the elements as a result of smaller element spacings is shown to minimize the variation in the value of the elements terminal currents across a 0.3 GHz to 3.0 GHz frequency range. This small variation in current translates into a minimal variation in the terminal impedances for a fixed excitation voltage. This is shown to be an …

Testing Of Recursive And Non-Recursive Algorithms For Real-Time Phasor And Frequency Estimations In Power Systems, Dhruv Sharma

Dissertations, Master's Theses and Master's Reports

Steady-state performance of various recursive and non-recursive algorithms are tested in this report according to the test signals given in the IEEE Standard C37.118.1-2011. Phase magnitude and phase angle of the power grid signals have been estimated using Discrete Fourier Transform (non-recursive), Discrete Fourier Transform (recursive), Least Square, and Wavelet Transform Algorithms. Frequency estimation is performed using Discrete Fourier Transform, Weighted Least Square, and Zero Crossing methods. These algorithms are evaluated in LabView software and tested by generating test signals in a Simulink model. Furthermore, Total Vector Error (TVE) is calculated using dynamic test signals as per the IEEE Standard …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

5g-Ucda Multi Antenna-To-Logical Cell Circular Fifo Mapping Strategy For High-Speed Train Wireless Communications, Subharthi Banerjee

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

2020 is the target year for the roll out of fifth generation wireless communication methodologies. The commercial vendors have characterized 5G as a collection of disruptive set of technologies to provide high throughput, low latency communication supporting a variety of services, i.e., machine to machine communication to next generation base stations and vehicle-to-vehicle communication to radio-over-fiber and high mobility channels. High-speed train wireless communication channels as a subset of high mobility channels have their clear advantages and disadvantages considering other vehicular channels. The speed of high-speed trains is going to reach 500km/hr and with Hyperloop it may reach 1000km/hr. LTE …

Single Carrier Frequency Domain Equalization And Energy Efficiency Optimization For Mimo Cognitive Radio., Xiaohui Zhang

Electronic Theses and Dissertations

This dissertation studies two separate topics in wireless communication systems. One topic focuses on the Single Carrier Frequency Domain Equalization (SC-FDE), which is a promising technique to mitigate the multipath effect in the broadband wireless communication. Another topic targets on the energy efficiency optimization in a multiple input multiple output (MIMO) cognitive radio network. For SC-FDE, the conventional linear receivers suffer from the noise amplification in deep fading channel. To overcome this, a fractional spaced frequency domain (FSFD) receiver based on frequency domain oversampling (FDO) is proposed for SC-FDE to improve the performance of the linear receiver under deep fading …

Microstrip Patch Antenna Design And Analysis For Wireless Power Applications, Zachary Pinz

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Energy Harvesting And Storage: The Catalyst To The Power Constraint For Leveraging Internet Of Things (Iot) On Trains, Kelechi Nwogu

Department of Computer Electronics and Engineering: Dissertations, Theses, and Student Research

The success of Wireless Sensor Networks is heavily constrained by its reliance on storage technology like batteries, which are a finite resource. Whilst the number of transistors in an IC doubles every 18 months, the energy density of batteries is relatively flat during the same time period. This is a key challenge in leveraging the Internet of Things on trains.

The gravity of this problem is increased by an order of magnitude when the network is to be scaled up to hundreds or thousands of nodes. Comprehensive research and development efforts have been devoted to building ultra-low power sensors. These …

Stargrazer One: A New Architecture For Distributed Maximum Power Point Tracking Of Solar Photovoltaic Sources, Edgard Munoz-Coreas

Theses and Dissertations--Electrical and Computer Engineering

The yield from a solar photovoltaic (PV) source is dependent on factors such as light and temperature. A control system called a maximum power point tracker (MPPT) ensures that the yield from a solar PV source is maximized in spite of these factors. This thesis presents a novel implementation of a perturb and observe (PO) MPPT.

The implementation uses a switched capacitor step down converter and a custom digital circuit implementation of the PO algorithm. Working in tandem, the switched capacitor step down converter and the custom digital circuit implementation were able to successfully track the maximum power point of …

Wirelessly Controlled Smart Outlet, Andrew Godsil, Ariel Dubinsky

Electrical Engineering

Popularity of home automation devices has increased greatly in recent years due to higher affordability and simplicity through smartphone and tablet connectivity. For the purpose of this experiment, we have developed the Smart Outlet: a stand-alone communication unit, used to connect home outlets to the internet. The Smart Outlet controls lighting and simple appliances throughout the home, remotely, using wireless commands from the web. A Google Calendar interface directly controls the outlets’ function by scheduling them with dedicated calendar events. The calendar’s interface can even be accessed from multiple different platforms (i.e. phones, computers, tablets) for the convenience of all …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

An Adaptive Kalman Filter For Voltage Sag Detection In Power Systems, Hisham Odeh Alrawashdeh

Dissertations

The exact values of the noise covariance matrix of the Kalman filter state vector Q and the measured signal noise covariance matrix R must be obtained in order to achieve the optimal performance of the Kalman filter. There have been many techniques and assumptions made to evaluate and compute Q and R. The effects of Q and R are investigated in detail in this dissertation. Based on these investigations, the Kalman filter has been modeled to detect the fundamental signal amplitude variations of power system signals. This technique helps in evaluating voltage sags in power systems.

Two algorithms are …

Understanding Vehicular Traffic Behavior From Video: A Survey Of Unsupervised Approaches, Brendan Tran Morris, Mohan Manubhai Trivedi

Electrical & Computer Engineering Faculty Research

Recent emerging trends for automatic behavior analysis and understanding from infrastructure video are reviewed. Research has shifted from high-resolution estimation of vehicle state and instead, pushed machine learning approaches to extract meaningful patterns in aggregates in an unsupervised fashion. These patterns represent priors on observable motion, which can be utilized to describe a scene, answer behavior questions such as where is a vehicle going, how many vehicles are performing the same action, and to detect an abnormal event. The review focuses on two main methods for scene description, trajectory clustering and topic modeling. Example applications that utilize the behavioral modeling …

Impact Of Primary User Activity On The Performance Of Energy-Based Spectrum Sensing In Cognitive Radio Systems, Sara L. Macdonald

Electrical & Computer Engineering Theses & Dissertations

Increasing numbers of wireless devices and mobile data requirements have led to a spectrum shortage. However spectrum utilization percentages are often low due to the current static spectrum allocation process where primary users (PUs) are given exclusive use to spectrum. Several mechanisms to increase spectrum utilization have been proposed including opportunistic spectrum access (OSA). Cognitive Radio (CR) is an emerging concept in wireless communication systems that aims to enable OSA in licensed frequencies by secondary users (SUs). CR systems are expected to sense the spectrum in order to determine if the PU is transmitting. Therefore OSA performance relies on the …