Power and Energy Commons^™

Multilayer Concentrated Windings For Axial Flux Pm Machines, Vandana Rallabandi, Narges Taran, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Coreless axial flux machines are of interest because of the absence of stator core losses and cogging torque. These machines generally employ concentrated windings. One of the challenges with such a winding is that the torque producing MMF component that corresponds to the fundamental of the magnet excitation is accompanied by substantial asynchronous components. These harmonics cause losses in the rotor core and magnets, which can become significant at high speeds. This paper proposes a new multilayer winding arrangement to eliminate the non-torque producing MMF components. This winding is applied to a 12-coil 16-pole coreless axial flux machine. The efficacy …

Hybrid Water Pump, Dylan W. Grant, Wei Chen Yeh

Electrical Engineering

This project seeks to use multiple sources to power a water pump. We will design a system which will combine inputs from solar and wind energy production to ensure the pump will have enough power to run. This will create a system powered by clean energy and will be self-sustained once completed. This will theoretically create a more sustainable source of power for the pump than only one of the sources. Because the power sources don’t require outside inputs (aside from sun and wind), the pump can be placed in a remote area. This could be very helpful in developing …

Dc House Energy Management System, Zachary L. Eldredge, Zoe M. Hay

Electrical Engineering

In this work, a previously completed proof of concept for an Energy Management System (EMS) for the DC House project has been revised and re-implemented. The implemented design changes will improve the performance and reproducibility of the system. This new design of the EMS replaces the two-separate buck and boost DC-DC converters with a single bidirectional DC-DC converter to reduce components and improve efficiency. Analysis of the bidirectional DC-DC converter shows high efficiency especially at larger load currents. The code of the previous work was updated for smoother operation as well as to accommodate an LCD capable of displaying more …

Automatic Standby Power-Saving Power Strip, Trung Nguyen

Electrical Engineering

The Standby Power Saving Power Strip improves on common power strip functionality. The project reduces the power loss from most electrical devices’ standby power mode, while retaining the convenience of leaving the devices plugged-in. The surge protector automatically recognizes when the plugged-in devices enter standby power mode. Then, it shuts off power to that device and automatically provides power back to the plugged-in devices, when turned on.

Lab-Scale Circuit Breaker Module For Power System Laboratories, Amanda Barley, Allen C. Scozzari, Joshua E. Chung

Electrical Engineering

In this project, a circuit breaker that can simulate different types of power system faults is redesigned, constructed, and tested. They will then be implemented in power systems laboratory courses at Cal Poly. The project’s goal is to improve a previous circuit breaker design to help students better visualize how faults affect power systems in the real world. Two main improvements are made to the previous circuit breaker design. The first improvement is to power the breaker with a typical wall outlet adapter instead of the DC source from the Cal Poly power systems laboratory test benches. This lets the …

Dual Input Microinverter For Tandem Cells, Forrest M. Lipske, Daniel A. Dich-Dang

Electrical Engineering

For every solar panel, there is an inverter which transforms the harvested DC electricity into AC electricity so that it can connect to the grid and power household appliances. In this project, we examined a tandem solar cell being designed by Iris Photovoltaics which has two layers with two distinct outputs, and we explored several solutions to create a microinverter which can handle dual inputs from the tandem PV and combine them into a single AC output. To examine the viability of such a microinverter, we designed and simulated the DC-DC combination portion of the specialized dual input microinverter, resulting …

Solar Powered Electric Vehicle Charger, Jessica A. Bombardier Shaw, Andrew F. Moradpour

Electrical Engineering

This project will look into how to create an efficiently-operated solar powered electric vehicle charger. The solar panel will harvest energy from the sun that will be stored a battery pack to be readily available to charge an electric vehicle. These stations could be commercialized to be located along a highway, or personalized for a in-house installation.

Student Experimental Farm Smart Pathway Lighting System, Emily A. Whitaker, Vineal S. Singh, Edith Rodriguez

Electrical Engineering

This project works together with the Student Experimental Farm (SEF) and the DC House in order to install a smart lighting pathway system. This system will run off of DC power supplied by the solar panels connected to the DC House. This project tested and explored the group’s abilities to design and implement a full system run off of 48V DC. By installing this system it will greatly improve the ease for students to work at the SEF beyond daylight hours. The system will allow continuous dull lighting and will switch to full brightness once a person is detected. This …

Solar Roller - Solar Powered Usb Charging Station, Aaron Bartfeld, Tanner Mjelde, Kaylan Naicker

Electrical Engineering

As the necessity for renewable energy increases, solar power becomes more and more prevalent. At the same time, as technology increases, the necessity for charging one’s electronic devices also increases. The Solar Roller merges solar energy with the ability to charge one's electronic device in one compact cart. The Solar Roller is a solar-powered USB charging station that allows people of all backgrounds to develop a better understanding of alternative fuels, while charging their USB device. It has a touch screen display that provides voltage levels of the battery as well as a TV that displays solar powered information. The …

Microgrid Protection Student Laboratory, Ian Hellman-Wylie, Joey Navarro

Electrical Engineering

To better prepare students for careers in the electric power industry, specifically in the discipline of power system protection, the Electrical Engineering Department at Cal Poly San Luis Obispo proposed an initiative calling for the creation of new laboratory curriculum that uses microprocessor-based relays to give students hands-on experience in the application of protection theory. This report describes the creation of a system that meets this need by providing a laboratory-scale power system that demonstrates the use of common protective relays and protection schemes. This system provides a platform for laboratory coursework using protective relays for transmission line, transformer, and …

Light Sensing Automated Blinds, Andrew B. Hodges, Ryan C. Flick

Electrical Engineering

This project is solving the problem of wasted energy within buildings and homes, because currently the lights turned on inside building do not utilize natural, ambient light from the sun. Rather than having unnecessary light from a light source, the automated light sensing smart blinds can sense the amount of light outside the window and in the room, and then adjust the angle of the blinds to save energy by utilizing the available outdoor light. This way, the light source will not be running at maximum power output while there is excess light coming through the window. This project aims …

Mini High Temperature Test Unit Final Design Report, Kevin Liu, Juan P. Castillo

Mechanical Engineering

Lawrence Livermore National Laboratory has invested considerable effort to develop new standard for nuclear grade HEPA filters that can withstand high temperatures along with methods to optimally test not only the experimental filter media, but also new frame seals and media binders. Therefore, LLNL in collaboration with Cal Poly has designed and built a Mini High Temperature Testing Unit (MHTTU) to recreate conditions observed during a fire and to test different materials in an effective, inexpensive, regulated and reliable method. The existing prototype was unable to achieve the ideal testing conditions of 1000°F air at the low flow rates of …

Marine Gastrobot Final Design Report, Wesley B. Williams, Eric Kane Dreischerf, Tommy Nicholas Yath

Mechanical Engineering

The Marine Gastrobot sponsored by Dr. Christopher Kitts of the Cal Poly Center for Applications in Biotechnology was a research and development effort intended to explore the use of microbial fuel cell technology as a power source for underwater robots. Our team Ocean Locomotion succeeded in developing a first iteration of an underwater robotic platform suitable for microbial fuel cell integration. The primary feature of the design is its sinusoidal fin propulsion intended for benthic exploration with limited risk of entanglement. During the course of development, Ocean Locomotion explored the use of low power actuation methods and determined their limited …

Design And Construction Of 1800w Modular Multiple Input Single Output Non-Isolated Dc-Dc Converters, Angelo Miguel Asuncion Gallardo

Master's Theses

This thesis report details the design and construction of non-isolated DC-DC converters to create a Multiple Input Single Output (MISO) converter for combining multiple renewable energy sources into one single output. This MISO uses the four-switch buck-boost topology to output a single 48V from multiple nominal 24V inputs. The MISO converter implements a modular approach to deliver 1800W output power. Each module in the MISO is rated at 600W and they share the output power equally. Hardware results show that the converter produces 1800W of output power from three sources with 96.4% efficiency. Each module also demonstrates equal sharing feature …

A Modified Boost Converter With Reduced Input Current Ripple, Nathan H. Lentz

Master's Theses

Battery-powered trends in consumer electronics, transportation, and renewable energy sectors increase demands on DC/DC converter technology. Higher switching frequency and efficiency reduces solution size and cost, while increasing power capabilities. Still, switching noise remains the primary drawback associated with any DC/DC converter. Reducing a converter’s input ripple helps prevent switching noise from spreading to other systems on a shared DC power bus. This thesis covers the analysis, simulation, and implementation of a recently-proposed boost converter topology, alongside an equivalent standard boost converter, operating in steady-state, continuous conduction mode. A Matlab-based simulation predicts each converter’s input ripple performance using a state-space …

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Generalized Differential Calculus And Applications To Optimization, R. Blake Rector

Dissertations and Theses

This thesis contains contributions in three areas: the theory of generalized calculus, numerical algorithms for operations research, and applications of optimization to problems in modern electric power systems. A geometric approach is used to advance the theory and tools used for studying generalized notions of derivatives for nonsmooth functions. These advances specifically pertain to methods for calculating subdifferentials and to expanding our understanding of a certain notion of derivative of set-valued maps, called the coderivative, in infinite dimensions. A strong understanding of the subdifferential is essential for numerical optimization algorithms, which are developed and applied to nonsmooth problems in operations …

Iii-Nitride Nanowire Light-Emitting Diodes: Design And Characterization, Dipayan Datta Choudhary

Theses

III-nitride semiconductors have been intensively studied for optoelectronic devices, due to the superb advantages offered by this materials system. The direct energy bandgap III-nitride semiconductors can absorb or emit light efficiently over a broad spectrum, ranging from 0.65 eV (InN) to 6.4 eV (AlN), which encompasses from deep ultraviolet to near infrared spectrum. However, due to the lack of native substrates, conventional III-nitride planar heterostructures generally exhibit very high dislocation densities that severely limit the device performance and reliability. On the other hand, nanowire heterostructures can be grown on lattice mismatched substrates with drastically reduced dislocation densities, due to highly …

Operating Temperature Of A Solar Thermal Stirling Engine, Spencer Beck

Senior Theses

This paper explores the relationship between the operating temperature and electricity production of a simple heat engine. A Stirling engine was designed and constructed which runs on solar thermal energy collected by a Fresnel lens. The surface area of the solar collector was varied. This manipulated the operating temperature of the Stirling engine in order to measure power output. The mechanical energy from the engine was converted to electricity using a DC motor running in reverse, acting like a generator, in conjunction with an Arduino for data collection. Although adjustments must be made in order to improve the efficiency of …

Are Solar Panels A Viable Power Source For A Green Energy Vehicle?, Mason C. Adams

Senior Theses

A solar cell powered go-kart has been built and tested. The result shows using solar energy alone cannot meet the requirement of running a regular passenger car. This is due to the limited surface area of the passenger car. This thesis also discusses the operating principles of solar panels, the physics of P type and N type semiconductors, and the formation of the PN junction, as well as the solar current. Modifications of an existing go-kart are described in detail in this thesis. Suggestions for making green vehicles are discussed as well.

Determination Of Single Pole Breaker Reclose Time And System Performance Using Real Time Simulation, Venkata Sridivya Godavarthi

LSU New Orleans Theses and Dissertations

This thesis investigates single pole reclosing in series capacitor compensated line. An algorithm is developed to determine the optimal dead time required for single pole reclose of circuit breakers and to reduce the randomness of reclosing time. The algorithm considers conditions of system, fault, voltage zero crossing, arc, and IEEE C37.104-2012 standard de-ionization time. This study also addresses difficulties of single pole reclose operation such as over-voltages at the line, secondary arc extinguishing time, dead time, over-voltages across the series capacitor, and negative sequence current. The system performance is evaluated using a set of metrics based on those operation difficulties. …

2017 Spring Engr333 Project Final Report (Section A), Devin Auld, Scott Bokach, Joshua Bronner, Alex Meador, Ryan Hoek, Robert Lanser, Matthew Lenko, Elliot Slenk, Brendan Biesboer, Kyle Mailhot, Nate Zylstra, Jonah Engel, Rich Floro, Björn Krebs, Ethan Postmus, Cameron Bell, Caleb Bieske, Chris Griffin, Bernice Portugal, Ryan Beezhold, Dillon Carhuff, Ian Mcclaskie, Jared Vanderklay, Rounak Chatterjee, Toby Dalla Santa, Jenny Haney, Joel Hoskins, Caleb Senyshyn

ENGR 333

The objective of ENGR-333-A was to develop a well-defined, bottom-up energy demand model for the energy consumption of the dormitories on Calvin College’s campus for each year of the past decade within an accuracy of ± 2%.

2017 Spring Engr333 Project Final Report (Section B), Daniel Dick, Nathan Swaim, Jonathan Sager, Ellen Reidy, Jordan Swets, Joel Van Dyke, Connor Macdonald, Josiah Markvluwer, Justin Rohlicek, John Lee, Zach Mouw, Daniel Wharton, Sam Hanover, Jay Noyola, Adam Christenson, Scott Stamper, Aaron Tucker, Bethany Waanders, Joel Schaefer, Maddie Collins, Matthew Cok, Philip Kim, Steve Vanden Berg

ENGR 333

The Physical Education Complex is located in the North-end of Calvin College’s campus, and supports many athletic, academic, event and recreational functions. Due to its heavy use, the complex contributes 20% of the College’s electricity consumption. Monetarily, this equated to electricity costs of about $385,000 last year. With these financial implications, the College is searching for ways to reduce the cost. While there is little to no room for electricity cost rate reductions, there is opportunity for improvement through the implementation of more efficient components. However, the sources of electricity demand are largely unknown. Our objective is to develop a …

2017 Spring Engr333 Seminar Presentation, Jonah Engel, Rich Floro, Björn Krebs, Ethan Postmus, Brendan Biesboer, Kyle Mailhot, Nate Zylstra, Ryan Beezhold, Dillon Carhuff, Ian Mcclaskie, Jared Vanderklay, Rounak Chatterjee, Toby Dalla Santa, Jennifer Haney, Joel Hoskins, Caleb Senyshyn, Alex Meador, Scott Bokach, Devin Auld, Joshua Bronner, Elliot Slenk, Matthew Lenko, Robert Lanser, Ryan Hoek, Cameron Bell, Caleb Bieske, Chris Griffin, Bernice Portugal, Sam Hanover, Dan Wharton, Jay Noyola, Zachary Mouw, John Lee, Daniel Dick, Jonathan Sager, Nathan Swaim, Ellen Reidy, Jordan Swets, Joel Van Dyke, Connor Macdonald, Josiah Markvluwer, Justin Rohlicek, Adam Christensen, Scott Stamper, Aaron Tucker, Bethany Waanders, Joel Schaefer, Maddie Collins, Matthew Cok, Philip Kim, Steve Vanden Berg

ENGR 333

File for student presentation, given by students in the Spring 2017 class of ENGR333.

Methanol Steam Reforming: Na Doping Of Pt/Ysz Provides Fine Tuning Of Selectivity, Michela Martinelli, Gary Jacobs, Uschi M. Graham, Burtron H. Davis

Center for Applied Energy Research Faculty and Staff Publications

In this work, we found that sodium doping can be used to improve CO₂ selectivity for supported Pt catalyst during methanol steam reforming. These materials are usually very active in the low temperature range; however, they are characterized by high selectivity of CO, which is a poison in downstream polymer electrolyte membrane fuel cells (PEM-FC) application. With Na doping, we found that CO₂ selectivity was higher than 90% when 2.5 wt.% of sodium was added to Pt/YSZ. We have speculated that the different product distribution is due to a different reaction pathway being opened for CH₃OH …

Development Of Intermediate Band Solar Cell Through Ingan Quantum Well Structures, Kelly Mckenzie

Electrical Engineering Undergraduate Honors Theses

In the search for high-efficiency solar cells, In_xGa_1-xN has come under scrutiny as a unique material with high potential. This is due to characteristics including an easily tunable bandgap, large range of potential bandgap values, and high heat resistance. However, one factor limiting its adaptation is the high density of crystal defects. In this thesis, the qualities of InGaN are discussed and the intermediate band solar cell structure is introduced. Additionally, the growth and characterization of two sets of InGaN-based solar cell devices are reported and evaluated.

Protective Relaying Student Laboratory, Kenan W. Pretzer

Master's Theses

Facing a rapidly-changing power industry, the electrical engineering department at Cal Poly San Luis Obispo proposed Advanced Power Systems Initiatives to better prepare its students for entering the power industry. These initiatives call for the creation of a new laboratory curriculum that uses microprocessor-based relays to reinforce the fundamental concepts of power system protection. This paper summarizes a laboratory system fit for this task and presents a set of proposed laboratory experiments to establish a new laboratory course at Cal Poly. The experiments expose students to the capabilities of industry-standard microprocessor-based relays through hands-on procedures that demonstrate common power system …

On The Effect Of Design Tolerances On The Performance Of Synchronous Pm Machines Evaluated According To The Ieee Std 1812, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

In the process of designing an electric machine, the systematic study of tolerances for the design variables and material properties is of the utmost importance. This paper proposes a method by which possible variations of the design variables and material properties can be distinguished. The design of experiments (DOE) technique, open-circuit and short-circuit tests, with minimum instrumentation requirements, have been employed. Virtual tests are conducted based on the recently approved IEEE 1812 testing guide for PM synchronous machines. As a case study, a 100 hp 16-pole 18-slot spoke-type PM machine is discussed. It is shown that variation in magnet remanence, …

Axial-Flux Pm Synchronous Machines With Air-Gap Profiling And Very High Ratio Of Spoke Rotor Poles To Stator Concentrated Coils, Vandana Rallabandi, Narges Taran, Dan M. Ionel, Ion G. Boldea

Power and Energy Institute of Kentucky Faculty Publications

Permanent magnet machines including a magnetic gearing effect are attractive for low-speed high-torque applications. This paper proposes a dual-stator axial-flux machine topology with a high ratio for the number of rotor poles to concentrated stator coils. The stator consists of a relatively small number of teeth, with each tooth including multiple smaller/auxiliary teeth. The rotor employs spoke-type permanent magnets, which result in high flux concentration, thereby further improving the torque density. The paper discusses the principle of operation of the proposed machine topology. Finite element results on example designs with 6 stator teeth, each having 2 and 3 auxiliary teeth, …

Reduction In Recombination Current Density In Boron Doped Silicon Using Atomic Hydrogen, Matthew Garett Young

Graduate Theses and Dissertations

The solar industry has grown immensely in recent years and has reached a point where solar energy has now become inexpensive enough that it is starting to emerge as a mainstream electrical generation source. However, recent economic analysis has suggested that for solar to become a truly wide spread source of electricity, the costs still need to plummet by a factor of 8x. This demands new and innovative concepts to help lower such cost. In pursuit of this goal, this dissertation examines the use of atomic hydrogen to lessen the recombination current density in the boron doped region of n-type …