Power and Energy Commons^™

Wireless Charging For Bluetooth Earphones, Daniel Carlson

Electrical Engineering

This project involves designing and building an inductive charging system for Bluetooth earphones. This system provides a charging dock for a pair of retrofitted Bluetooth earphones and focuses on ease-of-use and convenience for the user. The motivations for this project include providing charging compatibility to changing audio technology and trends. Smart phones and other audio products are increasingly leaning towards wireless (Bluetooth) audio, and wireless headphones/headsets are naturally becoming more prevalent to match this trend. A small, easy to use, and efficient charging dock for these earphones seems like a necessary accessory for this technology to seem attractive to consumers. …

A Novel Time-Domain Method Of Fault Diagnosis In Induction Motors, Bryan J. Davis

Honors Scholar Theses

This paper introduces a novel time-domain method for detecting the four major types of induction motor faults without requiring complex signal processing or additional sensors other than those already in place for closed-loop motor control. This method artificially modulates the motor current feedback signal with a perturbed frequency that oscillates about the characteristic frequency of the fault in question. After filtering out the unwanted frequency components that result from the modulation, the selected fault-indicative component is a very slow sinusoid that is only present when the fault is present. The method looks for this fault-indicative component by monitoring the time …

Optimization Of Graphene Parameters For The Development Of Supercapacitors, Jessica L. Montgomery

Mechanical Engineering Undergraduate Honors Theses

In the growing market of evolving electronic devices and the sustainable goals of the energy industry, better sources of energy dense storage devices are needed. Carbon based supercapacitors have attracted the attention of research due to the natural properties of high electrical conductivity, chemical and electrochemical stability, and high surface area. The object of this thesis is to expand upon current knowledge of reduced graphene oxide to better understand the effectiveness of the material as electrode in supercapacitors. This thesis will focus on the physical orientation of supercapacitors to further develop a device that will allow a set of supercapacitors …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Linear Quadratic Optimal Control For A Cascaded Converters-Based Microgrid, Amlam Niragire

Graduate Theses and Dissertations

There is a constant transformation of the electric grid due to an ongoing interest in the deployment of renewable energy resources and electric microgrid formation. This transformation, though advantageous in many ways, poses great challenges for the energy industry and there must be a constant improvement in modeling, simulation, analysis and control techniques in order to characterize and optimize the system design and operation. In this light, the scope of this thesis is focused on developing a linear model, analyzing the stability and designing an optimal linear quadratic regulator (LQR) for a microgrid system. The microgrid system used is inspired …

Applications Of Krylov Subspace And Balanced Truncation Model Order Reduction In Power Systems, Sebastian Emanuel Garrido

Graduate Theses and Dissertations

Dynamic representations of power systems usually result in the order of hundreds or even thousands of buses. Therefore, reduction of these dynamic representations is convenient. Two applications of model order reduction in power systems are discussed in this thesis. First, Krylov subspace-based method is applied to the IEEE-123 Node Test Feeder in the context of distribution-level power systems simulation. Second, a Balanced Truncation-based model reduction is implemented in the 3-Machine 9-Bus system for designing a power system controller in the context of generation- and transmission-level power systems.

First, for the IEEE-123 Node Test Feeder, a two-sided Arnoldi algorithm is proposed …

Energy Harvesting From Exercise Machines: Comparative Study Of Ehfem Performance With Dc-Dc Converters And Dissipative Overvoltage Protection Circuit, Cameron Kiddoo

Master's Theses

Energy Harvesting from Exercise Machines (EHFEM) is an ongoing project pursuing alternate forms of sustainable energy for Cal Poly State University. The EHFEM project seeks to acquire user-generated DC power from exercise machines and sell that energy back to the local grid as AC power. The end goal of the EHFEM project aims to integrate a final design with existing elliptical fitness trainers for student and faculty use in Cal Poly’s Recreational Center. This report examines whether including the DC-DC converter in the EHFEM setup produces AC power to the electric grid more efficiently and consistently than an EHFEM system …

Hardware Realization Of A Residential Static Var Compensator, Muhammad Kamran Latif

Boise State University Theses and Dissertations

Conservation by Voltage Reduction (CVR) is the implementation of a distribution voltage strategy whereby all distribution voltages are lowered to the minimum allowed by the equipment manufacturer. This strategy is rooted in the fact that many loads consume less power when they are fed with a voltage lower than nominal. Electric utility companies consider CVR as a potential solution for managing power in distribution networks. However, a difficult challenge is to keep end-of-line (EOL) voltages within an acceptable range of the ANSI Standard C84.1. Therefore, to achieve maximum benefit from CVR, electric utilities should be able to regulate residential voltages …

Novel Composites Between Nano-Structured Nickel Sulfides And Three-Dimensional Graphene For High Performance Supercapacitors, Xiaomin Wang, Huanglin Dou, Zhen Tian, Jiujun Zhang

Journal of Electrochemistry

In this paper, a three-dimensional graphene (3DG) network grown on nickel foam was employed as a template for synthesizing graphene-based composite materials of supercapacitor electrode. The composites (crystal Ni₃S₂ nanorods on the surface of 3DG (abbreviated as Ni₃S₂/3DG)) were obtained through a one-step hydrothermal reaction. The morphological and structural evolution of the Ni₃S₂/3DG composites were investigated by SEM, TEM, XRD and Raman spectroscopy. Detailed electrochemical characterization showed that the Ni₃S₂/3DG-coated electrodes exhibited both a specific capacitance as high as 1825 F·g^-1 at 5 mV·s …

Designing Pt-Skin Of Pt-Based Bimetallic Electrocatalysts For Oxygen Reduction Reaction, Binwei Zhang, Yunxiao Wang, Yanfei Xu, Huakun Liu, Shixue Dou

Journal of Electrochemistry

In the past decade, great advancement has been made in the development of nanocatalysts for energy conversion and storage. Pt-skin of Pt-based bimetallic has shown a great potential in the tuning the electronic structures of electrocatalytically active materials toward oxygen reduction reaction. Here, we offer a brief overview of the recent research on the design and preparation of catalysts. Our focus is paid on the systematic studies of preparation and performance of Pt-skin catalysts towards oxygen reduction reaction.

Recent Progress In Template-Assisted Synthesis Of Nitrogen-Doped Porous Carbons For Oxygen Electroreduction, Wenhan Niu, Ligui Li, Shaowei Chen

Journal of Electrochemistry

Nitrogen (N)-doped porous carbons are potential alternatives to precious metal catalysts for oxygen reduction reaction (ORR) at the cathodes of proton exchange membrane fuel cells and metal-air batteries. Template-assisted synthesis has been used extensively as a robust and versatile method in the preparation of such carbon catalysts, where the ORR activity has been found to be dependent on various structural parameters, such as the concentrations and molecular configurations of the dopants, and the porosity, surface accessibility and electrical conductivity of the carbon materials. In this review, we summarize recent progress in this area of research focusing on the design, preparation …

Comparative Studies Of Fe, Ni, Co And Their Bimetallic Nanoparticles For Electrochemical Water Oxidation, Maduraiveeran Govindhan, Brennan Mao, Aicheng Chen

Journal of Electrochemistry

The design of efficient, durable, and earth-abundant electrocatalysts via environmentally compatible strategies for the oxygen evolution reaction (OER) is a vital for energy conversion processes. Herein we report a facile approach for the fabrication of low-cost and earth abundant metal catalysts, including iron (Fe), nickel (Ni), cobalt (Co), CoNi, and CoFe nanoparticles (NPs) on titanium (Ti) substrates through a one-step electrochemical deposition. Field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) spectrocopy, X-ray photoelectron spectroscopy (XPS), and electrochemical techniques were employed to characterize these nanoparticles. Our electrochemical results revealed that among the five synthesized nanomaterials, the …

Impact Of Nafion Loading And Anion Adsorption On The Synthesis Of Pt Monolayer Core-Shell Catalysts, Lijun Yang, Dustin Banham, Elod Gyenge, Siyu Ye

Journal of Electrochemistry

Carbon supported palladium (Pd) nanoparticles were used as a model core material for the synthesis of platinum (Pt) monolayer core-shell catalysts using rotating disk electrode method and a copper (Cu) under potential deposition technique. The impact of Nafion on the synthesis process was revealed by electrochemical testing with various Nafion contents. The existence of Nafion influenced the Cu under potential deposition, galvanic replacement and eventually the oxygen reduction reaction activity of the core-shell catalyst. However, as long as the Nafion content was less than 5 wt% in the test film, adding Nafion could help to bind catalyst onto the surface …

Comparison Of Oxygen Reduction Reaction Activity Of Pt-Alloy Nanocubes, Yongan Tang, Lin Dai, Shouzhong Zou

Journal of Electrochemistry

Alloying Pt with the first row non-noble transition metals has been demonstrated to increase the catalytic activity toward oxygen reduction reaction (ORR), which is the cathode reaction of the proton exchange membrane fuel cells (PEMFCs) and metal-air batteries. However, how much the ORR activity improvement comes from the alloying elements remains controversial. In this paper, the nanocubes of PtMn, PtFe, PtCo, and PtNi with the similar size and composition were prepared and their ORR activities were explored, in order to investigate the effects of alloying elements on the catalytic activity. The use of cubic shape particles minimizes the contribution to …

Electrodeposition Of Ruo2 Layers On Tio2 Nanotube Array Toward Co2 Electroreduction, Bei Jiang, Lina Zhang, Xianxian Qin, Wenbin Cai

Journal of Electrochemistry

RuO₂/TiO₂ composite materials have multitude of electrocatalytic applications including but not limited to CO₂ reduction reaction (CO₂RR). RuO₂/TiO₂ electrodes were previously prepared by repetitive coating and thermal decomposition (TD) of a Ru(III) precursor solution on Ti substrate. In this work, electrochemical potential cycling is applied to deposit amorphous RuO₂ (α-RuO₂) layers onto TiO₂ nanotube array (TNA) (RuO₂^CV/TNA) preformed on Ti foil. SEM, GIXRD, and voltammetry are applied to characterize the structures of the resulting RuO₂^CV/TNA. Ru loading on the RuO_{2 …}

5g-Ucda Multi Antenna-To-Logical Cell Circular Fifo Mapping Strategy For High-Speed Train Wireless Communications, Subharthi Banerjee

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

2020 is the target year for the roll out of fifth generation wireless communication methodologies. The commercial vendors have characterized 5G as a collection of disruptive set of technologies to provide high throughput, low latency communication supporting a variety of services, i.e., machine to machine communication to next generation base stations and vehicle-to-vehicle communication to radio-over-fiber and high mobility channels. High-speed train wireless communication channels as a subset of high mobility channels have their clear advantages and disadvantages considering other vehicular channels. The speed of high-speed trains is going to reach 500km/hr and with Hyperloop it may reach 1000km/hr. LTE …

Optimal Control For Wind Turbine System Via State-Space Method, Mudhafar Lazam Shanoob

Theses and Dissertations

Renewable energy is becoming a fascinating research interest in future energy production because it is green and does not pollute nature. Wind energy is an excellent example of renewable resources that are evolving. Throughout the history of humanity, wind energy has been used. In ancient time, it was used to grind seeds, sailing etc. Nowadays, wind energy has been used to generate electrical power. Researchers have done a lot of research about using a wind source to generate electricity. As wind flow is not reliable, there is a challenge to get stable electricity out of this varying wind. This problem …

Design And Experiments Of A Sic Power Mosfet-Based Bidirectional Switching Power Pole (Bspp), Hussain Khthear Sayed Subhii

Theses and Dissertations

This research presents the design and experiments of a SiC power MOSFET-based bidirectional switching power pole (BSPP) by benefiting from the advantages of SiC power MOSFETs: high-speed switching, high power density, high operating temperatures, and low power losses. The main goal of this research is to design a printed circuit board (PCB) prototype with a minimum parasitic inductance to improve the switching transient performance of the SiC MOSFETs for the BSPP application. The effects of the parasitic inductance of the PCB power traces were investigated, for the BSPP application, based on the experimental, simulation, and theoretical analyses. The PCB prototypes …

Hand Cranked Generator For Mobile Devices, Kyle Brown, Monique Butoto, Stephen Cain, Steven Corio, Brock Stevenson

Thinking Matters Symposium Archive

It’s estimated that over 90% of American adults own cell phones while over 70% of the United States land area belongs to rural counties. It is a challenge to charge mobile devices in these remote and rural areas given the lack of access to power sources. This lack of power in remote destinations limits the general use of mobile devices for outdoor enthusiasts, as well as a survival means for all who need access to a portable power generation device, especially in emergency situations. There are other portable generators currently available on the market, but our project wanted to take …

5‐Minute Power Ouptut Data For A 1.72kwp Pv System With Weather Variables, Lacour Ayompe, Aidan Duffy, Kevin O'Farrell

Other resources

This dataset contains 5-minute power (AC and DC) power output date from a 1.72kWp PV system located in Dublin in 2009-10 together with input weather variables and system parameters. Details below.

Geographical site: FOCAS Institute building roof top, Dublin Institute of Technology, Kevin Street, Dublin 2, Ireland.

Situation: Latitude 53.4degN Longitude -6degE

Time zone GMT

Installation date: 4th April 2008

PV array orientation: Tilt 53deg Azimuth 0deg

Near shadings: No shadings

Building height: Approximately 12 m

PV array capacity: 1.72 kWp

Collection period: 4^th April 2009 – 3^rd April 2010

The data acquisition system consisted of a Sunny …

Centralized Control For Dc Microgrid Using Finite State Machine, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

In this paper, an autonomous communication-based centralized control for DC microgrids (MG) has been developed and implemented. The proposed controller enables smooth transition between various operating modes. Finite state machine (FSM) has been used to mathematically describe the various operating modes (states), and events that may lead to mode changes (transitions). Therefore, the developed centralized controller aims at optimizing the performance of MG during all possible operational scenarios, while maintaining its reliability and stability. Results of selected cases have been presented. These results show stable transition between modes, verifying the validity and applicability of the proposed controller.

Deposition Of Silicon Thin Films By Ion Beam Assisted Deposition, Tejaswini Miryala

Electrical & Computer Engineering Theses & Dissertations

With the depletion of non-renewable energy sources owing to increasing demands, we need to develop renewable energy sources, which can replace them with cleaner energy sources. The solar industry is one of these renewable energies. In spite of having very high potential, harvesting solar energy has been a challenge due to the cost of solar cells. Silicon dominates the photovoltaic industry, but even this technology can accommodate great improvements. This can be done notably by finding low cost deposition techniques for the silicon. The main aim of this thesis is to form high-quality nanocrystalline silicon thin films with the help …

Modification Of Deposition Process Parameters For Uniform Indium Layer Deposition, Isaac Butt

Electrical & Computer Engineering Theses & Dissertations

The need for more efficient light to energy converting cells has long been a subject of research and development. With abundant availability of solar energy that the earth receives, the photovoltaic industry has sought materials that could serve the purpose of great energy conversion. The photovoltaic industry is mainly dominated by Silicon owing to its abundant availability, reliability and economic cost. However, due to limitations on efficiency improvements, some focus has shifted toward III-V based solar cells with a great potential for attaining higher efficiency and multi-junction applications. However, the cost of the III-V materials is extremely high due to …

A Study Of The Sensitivity Of Energy Conversion Efficiency To Load Variation In Class-E Resonant Power Inverter, Richard Samuel Jennings

Electrical & Computer Engineering Theses & Dissertations

In this thesis the sensitivity of energy conversion efficiency (ECE) and output power of a class-E resonant inverter under variable resistive and inductive load assignments is examined for wireless power transfer (WPT) applications. By performing simulation and mathematical analysis, it was found that the on-resistance of the switching device has minor effect on the design’s efficiency. Additional comparisons between the simulation and mathematical analysis show reasonable output power and ECE load variation performance for the design, but with unique load impedances where zero voltage switching (ZVS) and zero derivative switching (ZDS) are achieved. These comparisons also expose inaccurate mathematical assumptions. …

Study Of A High-Efficient Wide-Bandgap Dc-Dc Power Converter For Solar Power Integration, Yashwanth Bezawada

Electrical & Computer Engineering Theses & Dissertations

This research focuses on the design and analysis of a Boost cascaded Buck-Boost (BoCBB) power converter with super high efficiency in electric power conversion. The BoCBB power converter is based on emerging wide-bandgap silicon-carbide (SiC) MOSFETs and Schottky diodes, which have only 1/6 times of power loss in traditional silicon power semiconductor devices. The BoCBB power converter can be widely applied in solar harvesting for the National Aeronautics and Space Administration (NASA), military bases and electric utilities, as well as high-power DC motor drives for the electric vehicles, robotics, and manufacturing and product lines.

This research analyzed the topology and …

Investigation Of Low Cost Substrate Approaches For Iii-V Solar Cells, Marlene Lydia Lichty

Electrical & Computer Engineering Theses & Dissertations

With the need for cleaner energy sources, which can displace fossil fuel, the solar cell industry is of particular interest due to the abundancy of the Sun. Silicon currently dominates terrestrial applications, but efficiency improvements have saturated. III-V based solar cells have reported the highest efficiencies, however, high costs due to substrates and fabrication processes have limited these devices to specialty applications, such as space. In order to reduce the cost associated with fabricating III-V semiconductor substrate material, two different approaches were taken in this work with a particular focus on making III-Vs more applicable outside of specialty applications, including …

Building Energy Model Calibration For Retrofit Decision Making, Nicolas R. Johnson

Dissertations and Theses

Accommodating the continued increase in energy demand in the face of global climate change has been a worldwide concern. With buildings in the US consuming nearly 40% of national energy, a concerted effort must be given to reduce building energy consumption. As new buildings continue to improve their efficiency through more restrictive energy codes, the other 76.9 billion square feet of current building stock falls further behind. The rate at which current buildings are being retrofit is not enough and better tools are needed to access the benefits of retrofits and the uncertainties associated with them. This study proposes a …

Predicting Solar Performance In A Contingency Environment To Meet Net-Zero Facility Power, Anthony D. Williams

Theses and Dissertations

The U.S. government is involved in contingency operations all over the world and these operations require operational support and sustainment in these locations; this includes the reliable delivery of power to base infrastructure. The traditional means of delivering this support requirement in austere environments has been the use of diesel-power generation that has an extensive logistical and economic tail. The research sought out contingency solar applications that may be implemented and operated to offset the facility demand loads in the location to achieve net-zero power. This research explores the technical feasibility of a deployable photovoltaic microgrid to deliver power to …

Power-Aware Datacenter Networking And Optimization, Qing Yi

Dissertations and Theses

Present-day datacenter networks (DCNs) are designed to achieve full bisection bandwidth in order to provide high network throughput and server agility. However, the average utilization of typical DCN infrastructure is below 10% for significant time intervals. As a result, energy is wasted during these periods. In this thesis we analyze traffic behavior of datacenter networks using traces as well as simulated models. Based on the insight developed, we present techniques to reduce energy waste by making energy use scale linearly with load. The solutions developed are analyzed via simulations, formal analysis, and prototyping. The impact of our work is significant …

Energy Harvesting From Exercise Machines: Buck-Boost Converter Design, Andrew E. Forster

Master's Theses

This report details the design and implementation of a switching DC-DC converter for use in the Energy Harvesting From Exercise Machines (EHFEM) project. It uses a four-switch, buck-boost topology to regulate the wide, 5-60 V output of an elliptical machine to 36 V, suitable as input for a microinverter to reclaim the energy for the electrical grid. Successful implementation reduces heat emissions from electrical energy originally wasted as heat, and facilitates a financial and environmental benefit from reduced net energy consumption.