Power and Energy Commons^™

Naio4 Oxidation Of Mussel Adhesive Protein Film And Its Corrosion Protection For Mg-1.0ca Alloy, Rui-Qing Hou, Ping-Li Jiang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The effect of oxidation of mussel adhesive protein (Mefp-1) film on the corrosive resistance for Mg-1.0Ca alloy was investigated by scanning electron microscopy (SEM), atom force microscopy (AFM), electron probe microanalysis (EPMA), Infrared reflection absorption spectroscopy (IRAS) and electrochemical methods. The results showed that the NaIO₄ induced oxidation of the pre-formed Mefp-1 film with porous morphology involved structural change of the DOPA group in the protein and resulted in a more uniform film with net-like morphology. The protein film without oxidation had an increasing resistance for the corrosion of Mg-1.0Ca alloy up to 7 days exposure. After oxidation, Epit …

Nanosized Fe2O3 On Three Dimensional Hierarchical Porous Graphene-Like Matrices As High-Performance Anode Material For Lithium Ion Batteries, Qin-Wei Zhang, Yun-Yong Li, Pei-Kang Shen

Journal of Electrochemistry

Ferric oxide (Fe₂O₃) as a promising anode material for lithium ion battery is due to its high theoretical capacity (1007 mAh·g^-1), earth abundance and low cost. The nanosized Fe₂O₃ on the three dimensional hierarchical porous graphene-like network (denoted as Fe₂O₃-3D HPG) has been synthesized by homogeneous precipitation and heat treatment. The 3D HPG can provide a highly conductive structure in conjunction to support well contacted Fe₂O₃ nanoparticles, and effectively enhance the mechanical strength of the matrices during volume changes, as well as improve the …

Preparation And Properties Of Titanium Based Metal Oxide Electrodes For Ammonia Nitrogen Wastewater Treatment, Xue Li, Meng Xue, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

In this paper, four types of titanium based metal oxides electrodes were prepared by thermal decomposition method: Ti/SnO₂+Sb₂O₃, Ti/SnO₂+Sb₂O₃/SnO₂+IrO₂, Ti/SnO₂+Sb₂O₃/SnO₂+RuO₂, Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂. The XRD results show that CeO₂ in Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂ displayed a good crystal structure, and there was no significant oxygen evolution reaction occurred after electrolytic oxidation. Compared with the other three electrodes, the Ce-doped …

A Low-Cost Loop Measurement Tool For Dc-Dc Converters, Shouee B. Lin

Master's Theses

Loop measurements are very important in evaluating dynamic performance of DC-DC converters. In this thesis, a small loop measurement tool as a low-cost alternative to a network analyzer is proposed. The tool is particularly useful when a network analyzer is not always available for use, for example when engineers are working on-site with customers or when a network analyzer is not affordable due to their relatively high cost. The design, simulation, and hardware implementation of the inexpensive loop measurement tool will be presented in this thesis. Results from computer simulation and hardware prototype demonstrate the ability of the proposed tool …

Con-Resistant Trust For Improved Reliability In A Smart Grid Special Protection System, Crystal M. Shipman, Kenneth M. Hopkinson, Juan L. Lopez Jr.

Faculty Publications

This paper applies a con-resistant trust mechanism to improve the performance of a communications-based special protection system to enhance its effectiveness and resiliency. Smart grids incorporate modern information technologies to increase reliability and efficiency through better situational awareness. However, with the benefits of this new technology come the added risks associated with threats and vulnerabilities to the technology and to the critical infrastructure it supports. The research in this paper uses con-resistant trust to quickly identify malicious or malfunctioning (untrustworthy) protection system nodes to mitigate instabilities. The con-resistant trust mechanism allows protection system nodes to make trust assessments based on …

A New Design Method For Vanadium Redox Batteries In Renewable Energy Systems, Casey Gibson, Karla G. Morrissey Unversity Of Arkansas, Fayetteville

Inquiry: The University of Arkansas Undergraduate Research Journal

This study investigated the behavior of vanadium redox flow batteries (VRFBs), which are batteries capable of easily switching between charging and discharging modes, making them a suitable option for storing intermittent sources of alternative energies (solar, wind, etc). Since different sizes of the battery provide varying voltages, optimal parameters for a particular home are key for implementation. These parameters, specifically the cell and tank volumes of the battery that are capable of providing consistent on-load voltage, were determined using data from a 13 kW solar array and a medium-sized house. Charge/discharge current values were used to run a mathematical model …

Romania's Participation To The European Assessment Project Titled Hyunder, Multi-Criterial Analyses Of Salt Cavern Locations, Ioan Iordache, Dorin Schitea, Adriana Marinoiu, Mihaela Buga, Mihai Balan, Ioan Stefanescu, Adrian Gheorghe, Mihaela Iordache, Viviana Cigolotti (Ed.), Chiara Barchiesi (Ed.), Michela Chianella (Ed.)

Engineering Management & Systems Engineering Faculty Publications

The scope of the work is to assess the potential, the actors and relevant business cases for large scale storage of renewable electricity by hydrogen underground storage in Romania. This presentation intends to provide a picture of the multi-criterial analyses of salt cavern locations in Romania.

The energy sector is facing with the necessity to store large energy quantities for short to long term in order to adapt to the increasingly intermittent renewable energy. The results of this presentation have originated from an ongoing European assessment project by the name of HyUnder (FCH JU, grant 303417) regarding utilization of salt …

Lighting Design In Europe: Aligning The Demands For Lower Energy Usage With Better Quality., Kevin Kelly, James Duff

Articles

Lighting design is one of the fastest changing areas in building engineering. It has evolved significantly in recent years due to changing technology and demands for improved quality, better control, reduced energy and sustainability. This paper is an overview of what is happening in Europe and elsewhere and examines the literature to find that latest recommendations in the Code for Lighting issued by the SLL (Society of Light and Lighting) in the UK change previous demands for equal illuminance across a working plane to more specific and demanding criteria. There are recommendations for qualitative metrics and better distribution of light …

Single Phase Multilevel Inverter For Grid-Tied Photovoltaic Systems, Martin Edward Prichard

Theses and Dissertations--Electrical and Computer Engineering

Multilevel inverters offer many well-known advantages for use in high-voltage and high-power applications, but they are also well suited for low-power applications. A single phase inverter is developed in this paper to deliver power from a residential-scale system of Photovoltaic panels to the utility grid. The single-stage inverter implements a novel control technique for the reversing voltage topology to produce a stepped output waveform. This approach increases the granularity of control over the PV systems, modularizing key components of the inverter and allowing the inverter to extract the maximum power from the systems. The adaptive controller minimizes harmonic distortion in …

A Computational Study Of A Photovoltaic Compound Parabolic Concentrator, William M. Vance

Browse all Theses and Dissertations

Routines have been written and added to the Wright State developed solar system simulation program called Solar_PVHFC to model incident solar radiation for a compound parabolic concentrator (CPC) that uses solar panels (photovoltaic panels) to produce electrical energy. Solar_PVHFC is a program that models a solar energy system composed of solar panels to produce electricity from the sun, hydrogen storage tanks to chemically store the energy produced by the solar panels, and fuel cells to convert between electrical and chemical energy when required. Solar_PVHFC features several adjustable parameters to model a solar panel, hydrogen storage, and fuel cell system. Now …

Comparing The Efficiency Of Heterogeneous And Homogeneous Data Center Workloads, Brandon Kimmons

College of Graduate Studies: Theses & Dissertations

Abstract

Information Technology, as an industry, is growing very quickly to keep pace with increased data storage and computing needs. Data growth, if not planned or managed correctly, can have larger efficiency implications on your data center as a whole. The long term reduction in efficiency will increase costs over time and increase operational overhead. Similarly, increases in processor efficiency have led to increased system density in data centers. This can increase cost and operational overhead in your data center infrastructure.

This paper proposes the idea that balanced data center workloads are more efficient in comparison to similar levels of …

Synchrophasor Assisted Efficient Fault Location Techniques In An Active Distribution Network, Anil Khanal

Dissertations

Reliability of an electrical system can be improved by an efficient fault location identification for the fast repair and remedial actions. This scenario changes when there are large penetrations of distributed generation (DG) which makes the distribution system an active distribution system. An efficient use of synchrophasors in the distribution network is studied with bidirectional power flow, harmonics and low angle difference consideration which are not prevalent in a transmission network. A synchrophasor estimation algorithm for the P class PMU is developed and applied to identify efficient fault location. A fault location technique using two ended synchronized measurement is derived …

Design Of Energy Storage Controls Using Genetic Algorithms For Stochastic Problems, Si Chen

Theses and Dissertations--Electrical and Computer Engineering

A successful power system in military applications (warship, aircraft, armored vehicle etc.) must operate acceptably under a wide range of conditions involving different loading configurations; it must maintain war fighting ability and recover quickly and stably after being damaged. The introduction of energy storage for the power system of an electric warship integrated engineering plant (IEP) may increase the availability and survivability of the electrical power under these conditions. Herein, the problem of energy storage control is addressed in terms of maximizing the average performance. A notional medium-voltage dc system is used as the system model in the study. A …

Stargrazer One: A New Architecture For Distributed Maximum Power Point Tracking Of Solar Photovoltaic Sources, Edgard Munoz-Coreas

Theses and Dissertations--Electrical and Computer Engineering

The yield from a solar photovoltaic (PV) source is dependent on factors such as light and temperature. A control system called a maximum power point tracker (MPPT) ensures that the yield from a solar PV source is maximized in spite of these factors. This thesis presents a novel implementation of a perturb and observe (PO) MPPT.

The implementation uses a switched capacitor step down converter and a custom digital circuit implementation of the PO algorithm. Working in tandem, the switched capacitor step down converter and the custom digital circuit implementation were able to successfully track the maximum power point of …

Nanostructured Semiconductor Device Design In Solar Cells, Hongmei Dang

Theses and Dissertations--Electrical and Computer Engineering

We demonstrate the use of embedded CdS nanowires in improving spectral transmission loss and the low mechanical and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide spectrum range provides an evidence for improving light transmission in the window layer and enhancing absorption and carrier generation in absorber. Nanowire CdS/CdTe solar cells with Cu/graphite/silver paste as back contacts, on SnO₂/ITO-soda lime glass substrates, yield the …

A New Islanding Detection Method Based On Wavelet-Transform And Ann For Inverter Assisted Distributed Generator, Zhengyuan Guan

Theses and Dissertations--Electrical and Computer Engineering

Nowadays islanding has become a big issue with the increasing use of distributed generators in power system. In order to effectively detect islanding after DG disconnects from main source, author first studied two passive islanding methods in this thesis: THD&VU method and wavelet-transform method. Compared with other passive methods, each of them has small non-detection zone, but both of them are based on the threshold limit, which is very hard to set. What’s more, when these two methods were applied to practical signals distorted with noise, they performed worse than anticipated.

Thus, a new composite intelligent based method is presented …

Average-Value Modeling Of Hysteresis Current Control In Power Electronics, Hanling Chen

Theses and Dissertations--Electrical and Computer Engineering

Hysteresis current control has been widely used in power electronics with the advantages of fast dynamic response under parameter, line and load variation and ensured stability. However, a main disadvantage of hysteresis current control is the uncertain and varying switching frequency which makes it difficult to form an average-value model. The changing switching frequency and unspecified switching duty cycle make conventional average-value models based on PWM control difficult to apply directly to converters that are controlled by hysteresis current control.

In this work, a new method for average-value modeling of hysteresis current control in boost converters, three-phase inverters, and brushless …

Compensation Methods For Demand Response, Zhaofeng Wang

Theses and Dissertations--Electrical and Computer Engineering

Recently, more and more disputations about how demand response should be compensated have arisen. Moreover, the court is about to rehear the Order 745. It probably will have significant impact on the whole working system used to be built for demand response before. Nowadays, some power companies and utilities think that they will endure profits leakage while demand response resources still are compensated.

In this research, knowledge of demand response, local marginal price, Order 745 and other related concept will be explained in detail in case of misunderstanding. Associated with all these knowledge, a possible compensation method will be proposed. …

Verification And Validation Of A Transient Heat Exchanger Model, Jayme Lee Carper

Browse all Theses and Dissertations

A statistical based verification and validation process is applied to the transient modeling of a shell and tube heat exchanger. A generic model of a heat exchanger was developed based on first principles as a sub-system of a larger thermal system model. This model was originally created without any experimental data, as it was not readily available. To provide the data necessary to apply the validation process, a thermal emulator was designed and built that allowed control of all system inputs to the heat exchanger, while also providing the instrumentation to record all required data. A wide test matrix was …

Boost Battery, Samuel Rauch, Alvin Ng, Lacy Sigman

Electrical Engineering

In modern times, the problem of a depleted battery confronts us too often. Whether it appears with a smartphone or with any other electronic device, the situation frustrates all consumers. This project designs and constructs a compact portable battery charger that charges through kinetic energy. Thus, one can perform everyday activities, such as walking or running, and charge up a backup battery with no extra effort or time. Additionally, an attachable band harvests thermal energy to maximize the amount of clean power generated. Energy harvesting from kinetic motion and thermal differences provide users with power when no actual power suppliers …

Smart Distributed Generation Systems Using Improved Islanding Detection And Event Classification, Bikiran Guha

College of Graduate Studies: Theses & Dissertations

Distributed Generation (DG) sources have become an integral part of modern decentralized power systems. However, the interconnection of DG systems to the power grid can present several operational challenges. One such major challenge is islanding detection. Islanding occurs when a DG system is disconnected from the rest of the power grid. Islanding can present serious safety hazards and therefore an accurate and fast islanding detection technique is mandated by DG interconnection standards such as IEEE 1547 and UL 1741. Conventional islanding detection techniques passively monitor the local power system parameters such as voltage and frequency to detect islanding. These techniques …

Temporary Bonding With Polydimethylglutarimide Based Lift Off Resist As A Layer Transfer Platform, T. Matsumae, A. D. Koehler, J. D. Greenlee, T. J. Anderson, H. Baumgart, G. G. Jernigan, K. D. Hobart, F. J. Kub

Electrical & Computer Engineering Faculty Publications

Bonding of lift off resist (LOR) was performed to realize temporary wafer bonding without residue. Bonding process conditions such as spin speed, pre-bake temperature, and bonding temperature were optimized to obtain a large bonded area with high bond strength. Under optimized process conditions, a bonded area covering over 98% of the wafer surface, with a room temperature bond strength of nearly 5 J/m² is achieved. During razor blade testing, fracture often occurs at the Si wafer. Moreover, debonding using an N-Methyl-2-pyrrolidone (NMP)-based solvent left the wafer surface extremely small amount of residue. Thus, the optimized bonding processed developed in …

Electric Vehicles In Smart Grids: Performance Considerations, Uttam Kumar Deb Nath

Theses: Doctorates and Masters

Distributed power system is the basic architecture of current power systems and demands close cooperation among the generation, transmission and distribution systems. Excessive greenhouse gas emissions over the last decade have driven a move to a more sustainable energy system. This has involved integrating renewable energy sources like wind and solar power into the distributed generation system. Renewable sources offer more opportunities for end users to participate in the power delivery system and to make this distribution system even more efficient, the novel "Smart Grid" concept has emerged. A Smart Grid: offers a two-way communication between the source and the …

Stand-Alone Solar-Pv Hydrogen Energy Systems Incorporating Reverse Osmosis, Daniel Clarke

Theses: Doctorates and Masters

The world’s increasing energy demand means the rate at which fossil fuels are consumed has increased resulting in greater carbon dioxide emissions. For many small (marginalised) or coastal communities, access to potable water is limited alongside good availability of renewable energy sources (solar or wind). One solution is to utilise small-scale renewably powered stand-alone energy systems to help supply power for everyday utilities and to operate desalination systems serving potable water (drinking) needs reducing diesel generator dependence. In such systems, on-site water production is essential so as to service electrolysis for hydrogen generation for Proton Exchange Membrane (PEM) fuel cells. …

Optimisation Of Stand-Alone Hydrogen-Based Renewable Energy Systems Using Intelligent Techniques, Adel Brka

Theses: Doctorates and Masters

Wind and solar irradiance are promising renewable alternatives to fossil fuels due to their availability and topological advantages for local power generation. However, their intermittent and unpredictable nature limits their integration into energy markets. Fortunately, these disadvantages can be partially overcome by using them in combination with energy storage and back-up units. However, the increased complexity of such systems relative to single energy systems makes an optimal sizing method and appropriate Power Management Strategy (PMS) research priorities.

This thesis contributes to the design and integration of stand-alone hybrid renewable energy systems by proposing methodologies to optimise the sizing and operation …