Power and Energy Commons^™

Current Tracking Power Supply For Sensor Calibration, Joshua Brookley

Electrical Engineering

This report highlights the steps taken to design and develop a constant 5V power supply capable of tracking load current. The background of its previous design, its necessary specifications and steps taken to achieve specifications are highlighted throughout the report. The report also contains conclusions and final recommendations for the design chosen, including its strengths and drawbacks.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments.  There is good reason for this, too.  In the State of California, office buildings represent the single largest user of energy in the commercial sector.  This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations.  The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Design Strategy For A 3-Phase Variable Frequency Drive (Vfd), Omar David Munoz

Electrical Engineering

This paper describes the design processes for a 3-Phase Variable Frequency Drive (VFD) as broken up into two stages: The AC-DC converter and the DC-AC converter. It acknowledges three (3) design versions, all. The output of the motor drive is 3-phase pulse width modulation (PWM) ranging in possible operation frequencies from 0Hz to 13kHz. The frequency control circuit uses an Arduino Uno based of the ATMEGA 328p.

Plug-In Hybrid Electric Vehicle Impacts On A Central California Residential Distribution Circuit, Darren Janigian

Master's Theses

The adoption of plug-in hybrid electric vehicles (PHEV) as a means of transportation over conventionally fueled vehicles introduces new challenges to the existing infrastructure of the electrical transmission and distribution system.  PHEV battery charging can represent a significant power demand that has the potential to overload electrical distribution components.  This study examines the impacts of PHEV charging on household service transformers, distribution conductors and voltage levels of a Central California residential distribution system.  The system is simulated using ETAP power system analysis software.  Transformers are the most vulnerable to overloads, especially if PHEV charging occurs in clusters.  Main feeder conductors …

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems.  As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire.  By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Energy Harvesting From Exercise Machines: Forward Converters With A Central Inverter, Nicholas Keith Lovgren

Master's Theses

This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project.  Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid.  This active clamp forward converter boasts a 14V-60V input voltage range and 150W power rating, which closely match the output voltage and power levels from the elliptical trainer.  The isolated topology outputs 51V, higher than previous, non-isolated attempts, which allows the elliptical trainers to interact with a central grid-tied inverter instead of many small ones.  The final converter operated at greater than …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Elliptical Machine Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Greg Hollister

Electrical Engineering

Designing a DC/DC Converter for the Cal Poly Energy Harvesting from Exercise Machines project requires special attention to the unique operating characteristics of the source and the load. An elliptical machine powered by a person exercising comprises the source, while an AC Inverter makes up the load. This project attempts to integrate the two devices with a custom DC/DC Converter in order to ultimately deliver power back into the power grid.

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

A Study Into The Use Of Microprocessor Relays For Motor Operated Valve (Mov) Electrical Protection In Nuclear Power Plants, James Andrew Tuccillo

Master's Theses

Motor Operated Valves (MOVs) are electro-mechanical components used to isolate, divert, or introduce fluid flow. The use of microprocessor relays for actuator motor electrical protection within nuclear power plants is the focus of this thesis and is implemented by providing a new and enhanced protection scheme that provides the adequate conservatism necessary to ensure valve operation while still maintaining electrical safety and continued operational availability. The comprehensive protection scheme is designed around an advanced microprocessor relay that has the ability to simulate the thermal overload conditions of a motor operating into a destructive thermal region. Through laboratory testing, the validity …

Off-Grid Photovoltaic System Design Project, Brian Duffy

Electrical Engineering

This project uses the BP SX 150S solar panel to charge a 12 V battery. This battery powers an AIMS 400 W Modified Sine Wave Inverter to provide 120 V RMS AC power to a load of up to 40 W. Inverter efficiency was measured at different load conditions. A control circuit was implemented to prevent overcharging or over-discharging of the battery, by disconnecting it from the panel or the load, respectively. The control circuit turn-on and cutoff voltages were measured versus battery voltage, and the on-resistance of the MOSFET switches was measured for various load currents. A table of …

Wireless Energy Transfer, Ryan Sasur

Electrical Engineering

Phones are now an integral component in the daily lives of people. Smartphones give access to movies, internet, and even books. This versatility and increased use can also lead to a shorter battery life. A phone with video viewing capabilities will be a heavy load on the unit’s battery. With phones utilizing 3G and 4G technology, even heavier demands are placed on the battery. As technology improves even further to provide for a larger entertainment experience on the phone, this could also lead to further battery degradation if the current battery situation isn’t addressed. To have a fully operational phone …

Hydro-Electric Generation System For The Dc House Project, Dennis Kwan, Mitchell Krug

Electrical Engineering

This paper focuses on the design, integration, and construction of a system that harnesses energy from flowing water. The system will be used in conjunction with the DC House Project. The proposed system employs a DC generator and DC-DC Boost-converter to provide electricity to the DC House at approximately 200-300W. Results of the testing and measurement show that the goal of the system is feasible, but currently limited. The generator could not output the specified power. Details of the design, along with ideas for further improvement, are presented in this report.

Effects Of Cloud-Induced Photovoltaic Power Transients On Power System Protection, Joel A. Nelson

Master's Theses

As the world strives towards finding alternative sources of power generation, photovoltaic generation has become an increasingly prevalent alternative energy source on power systems world-wide. This paper studies the effects that incorporating photovoltaic generation has on the existing power systems and their power system protection schemes. Along with the addition of this emerging alternative energy source comes the volatility of PV power generation as cloud-cover produces erratic variations in solar irradiance and PV power production. Such variations in PV power may lead to unfavorable operating conditions and power system failures. The issues addressed in this paper include a study of …

Designing A Photovoltaic System Hybrid For A Health Clinic In Camilo Ortega, Nicaragua, Jeremy Holliman

Electrical Engineering

As developing nations continue to foster the development of their technologies and economies, industrialized nations have taken an active approach in providing green and sustainable alternatives for them to consider. Non-profit organizations like Engineers Without Borders holds sustainable international development as paramount to all international projects that their student and professional chapters undertake. The Cal Poly Engineers Without Borders student chapter has implemented a variety of projects from slow sand filters to compressed earth blocks, and the Nicaragua team is in the process of designing a health clinic for the Camilo Ortega community. In order to power the health clinic, …

Modular Electronic Load, Jason March

Electrical Engineering

This project entails the design and development of a modular electronic load. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace whenever possible resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well as the hardware development is explained in details in this report. Results from hardware testing are also provided.

Enhanced Cal Poly Super System Simulink Model, Matthew Ogden Mcfarland

Master's Theses

The Cal Poly Sustainable Power for Electrical Resources (SuPER) project is a solar power DC distribution system designed to autonomously manage and supply the energy needs of a single family off-the-grid home. The following thesis describes the improvement and re-design of a MATLAB Simulink model for the Cal Poly SuPER system. This model includes a photovoltaic (PV) array, a lead-acid gel battery with temperature effects, a wind turbine model, a re-designed DC-DC converter, a DC microgrid, and multiple loads. This thesis will also include several control algorithms such as a temperature controlled thermoelectric (T.E.) cooler, intelligent load switching, and an …

Asynchronous Mips Processors: Educational Simulations, Robert L. Webb

Master's Theses

The system clock has been omnipresent in most mainstream chip designs. While simplifying many design problems the clock has caused the problems of clock skew, high power consumption, electromagnetic interference, and worst-case performance. In recent years, as the timing constraints of synchronous designs have been squeezed ever tighter, the efficiencies of asynchronous designs have become more attractive. By removing the clock, these issues can be mitigated. How- ever, asynchronous designs are generally more complex and difficult to debug. In this paper I discuss the advantages of asynchronous processors and the specifics of some asynchronous designs, outline the roadblocks to asynchronous …

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Distributed Generation: Issues Concerning A Changing Power Grid Paradigm, Scott G.M. Therien

Master's Theses

Distributed generation is becoming increasingly prevalent on power grids around the world. Conventional designs and grid operations are not always sufficient for handling the implementation of distributed generation units; the new generation may result in undesirable operating conditions, or system failure. This paper investigates the primary issues involved with the implementation of distributed generation and maintaining the integrity of the power grid. The issues addressed include power flow, system protections, voltage regulation, intermittency, harmonics, and islanding. A case study is also presented to illustrate how these issues can be addressed when designing distributed generation installation on an existent distribution system. …

Optimization Of P3ht-Pcbm Polymer Solar Cells Through Device Simulation And Manufacturing, James Boom

Computer Engineering

Given a good model and implementation of that model, computer simulation can be used to reduce the time and material costs of research. To this end I worked with other students to manufacture, test and simulate the single layer P3HT-PCBM solar cell. Using the data collected from this project, future work can then be done with the project's simulator to further optimize these types of solar cell devices.

Power Losses Associated With Stand-By Chargers, Robert Peralta

Electrical Engineering

Many average households across the United States may not realize how much power is saved by simply removing the plug from the receptacle when not being used. A misconception with stand-by/portable chargers is; if a device is not connected to the charger, but the charger is still connected to the wall, then the charger will not consume power. That statement is false. The following report will demonstrate how much power is lost in an average household. When a reference is made to an average house, I will refer to a 4 bedroom single family home. The house will have an …

Electric Bicycle System, Robert Cong, Rodney Martinez, Mark Casilang, Peter Vong

Electrical Engineering

The Electric Bicycle System is a systems project that incorporates three different ways of charging a lithium-ion battery: the 120VAC wall outlet, regenerative braking, and solar power; which is used to power an electric hub motor running a bicycle. The purpose of the project is to show that it is possible and relatively simple, to build an electric bicycle by oneself. This project can be broken down into five separate categories: the lithium-ion battery, the DC-DC boost converter, the solar panel, the motor, and the motor controller. Each of these will be built upon and improved further by future students, …

Transmission Line Forecast Study, Ryan Garoogian

Electrical Engineering

Load forecasting is the procedure to predict future loading conditions on a power system. Using simulation software such as ETAP you are able to predict abnormal voltage conditions, overloading of certain equipment, as well as determine protective equipment from short circuit studies. This study consisted of a 115kV loop network with multiple loading busses and one infinite bus. There was no separate generation other than the infinite bus. As load increased from forecasting to the future voltage dropped. To restore voltage levels capacitors were added at strategic points in the system to boost the voltage back up. Preparing yourself for …

High Voltage Switched-Mode Power Supply For Three-Phase Ac Aircraft Systems, John Brewer Jr., Kamaljit Bagha

Electrical Engineering

The purpose of this senior project was to design and fabricate a proof-of-concept Three-Phase Sinusoidal Switched-Mode Inverter with a power output capability of 10 kW and nominal operating frequency of 400 Hz for AC aircraft system applications. This senior project report includes a thorough discussion and presentation of the inverter system background, requirements, design, construction, and testing processes.

Energy Harvesting From Exercise Machines Cal Poly Recreation Center Implementation, Justin Arakaki, Praveen Lawrence, Audrey Nakamura

Electrical Engineering

As Cal Poly moves towards an environmentally friendly campus, the Energy Harvesting from Exercise Machines (EHFEM) project looks to generate a new source of renewable energy to help power the Cal Poly Recreation Center. The project focuses on retrofitting exercise machines to generate electricity. As of December 2009, Audrey Nakamura, Justin Arakaki, and Praveen Lawrence developed a design which allows the contribution of electricity generated from multiple exercise machines into the power grid.

The project will require an investigation of retrofitted machine designs by Cal Poly students and commercially available products and systems. The information obtained from the product research …

Energy Harvesting From Exercise Machines: Bike Buck-Boost Converter, Monroe Diamond, Brian Vuong

Electrical Engineering

This project is a continuation of previous senior projects’ work on Energy Harvesting from Exercise Machines (EHFEM). EHFEM seeks an alternative DC to DC converter to function within the existing exercise bike system. Implementing this new DC to DC converter aims to avoid previous complications other groups encountered, such as only running at low load currents, exceeding an input threshold voltage to begin operation, and performing at low efficiency. In developing this self‐generating exercise bike, Cal Poly wishes to incorporate an array of energy‐harvesting exercise machines in its Recreation Center expansion scheduled for completion in 2012.