Power and Energy Commons^™

Modeling And Efficiency Analysis Of Hybrid Ac/Dc And Conventional Ac House Electrical Systems For Net-Zero Energy Homes, Tyler Bury

Master's Theses

This thesis presents the design, simulation, and comparative efficiency analysis of hybrid AC/DC residential homes versus conventional AC homes for Net Zero Energy Homes (NZEH). Motivated by the increasing prevalence of DC-native technologies such as solar photovoltaics, battery storage, and DC-powered electronics, this work evaluates whether hybrid AC/DC distribution can offer measurable efficiency benefits over traditional systems. Twelve detailed house models were developed—six employing a hybrid AC/DC architecture and six based on conventional AC systems, each supplying a combination of AC and DC residential loads. Simulations were conducted using MATLAB/Simulink to model steady-state efficiency under various loading conditions. Grid configurations …

Modeling And Analysis Of A Hybrid Ac/Dc Green Seaport Power System With Photovoltaic Generation And Battery Energy Storage Systems, Corey Zaas

Master's Theses

This thesis investigates the modeling, simulation, and analysis of a Green Seaport power system integrating photovoltaic (PV) generation, battery energy storage systems (BESS), and coordinated protection within a hybrid AC/DC framework. The work improves a previously established model, enhancing it with detailed protection studies and simultaneous AC/DC power flow analysis using EasyPower software. The system was evaluated under a wide range of operating conditions, including varying solar irradiance, battery charge and discharge states, and both full and zero load conditions. Key performance indicators included voltage regulation, power factor behavior, equipment loading, protection device coordination, and total system power losses. Simulation …

Dc To Ac Voltage Source Converter Control System, Mohummad Tark Elgassier, Jordan M. Reichhardt, Brayden Richard Young

Electrical Engineering

The Voltage Source Converter Control System integrates a control system for a 2-phase half-bridge voltage source converter (VSC) utilizing a TMS320F2837xD Dual-Core Real-Time Microcontroller. VSCs are critical for the integration of power production into the power grid. They allow for accurate control over DC-AC energy conversion. Additionally with the improvement of renewable energies VSCs play a critical role in controlling the flow of these environmentally controlled and more unpredictable sources of energy. The control system regulates the output current and voltage, regulates switching patterns, and maintains power stability under varying loads. Within the control system Digital control systems, PWM generation, …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

This Is An Automated Software Platform For Grid Interconnection Of Renewable Energy Resources., Cathy Chen, Lani Nguyen

College of Engineering Summer Undergraduate Research Program

To help curb climate change, the United States is rapidly electrifying many sectors of the energy economy, such as transportation (electric vehicles) and home heating (electric heat pumps). Thus, recent years have witnessed an explosion of businesses that want to connect and operate energy resources on the electric grid. However, getting an energy resource connected to the grid is an arduous process that takes years or more, requires specialized technical knowledge, and requires navigating complex and varying regulatory procedures. This project will develop a software platform that leverages AI and high-performance computing to automate and accelerate grid interconnection and energy …

Power Controller For Insulated Solar Electric Cooker, Ryan Koshy, Justin Tae-Hoon Kim

Electrical Engineering

Insulated Solar Electric Cookers, or ISECookers, are devices created to aid those in impoverished regions improve safety, sustainability, and quality of life regarding their cooking practices. ISECookers present an alternative to traditional biofuel/biomass energy sources and provide a closed-loop, self-sustaining system that can be used in a variety of environments. These devices present solutions to widespread issues such as pollution, deforestation, and hazardous emissions as a result of traditional cooking in developing regions around the world. A notable obstacle of these devices is power delivery. Given the varying conditions experienced by a solar panel (inclement weather, irradiance irregularities, etc.), it …

Harmonic Flow Modeling And Analysis Of A Green Hybrid Ac/Dc Seaport Power System, Krishan Kaushal Ram, Taufik, Helen Yu, Siddharth Vyas

Master's Theses

This thesis aims to design and develop a model for a proposed Green Seaport power system and perform harmonic analysis. The model was developed using MATLAB Simulink and tests were performed by dividing the system into several Battery Energy Storage System (BESS) operating modes such as simultaneous charging and discharging, simultaneous charging, and simultaneous discharging. For each mode, BESS state of charge and other factors such as solar irradiance for the PV system, load levels and power factor were varied to observe the impact on system’s voltage Total Harmonic Distortion (THD) level and current Total Demand Distortion (TDD). 62 separate …

Battery Energy Storage System, Alec C. Maclean, Kaylen H. Schwartz, Kyle A. Begley

Electrical Engineering

The project is a continuation of part 1 of the “Reliability Measurement for Grid-Connected Solar System” project. The goal is to continue where the previous design failed. This project will configure an ITECH IT-6000C and Tabuchi Battery Energy Storage System (BESS) to the small-scale microgrid at the Cal Poly, San Luis Obispo EE Department. Initially, a system was designed to connect an ITECH IT-M3633 as a PV solar source emulator to the Tabuchi BESS within a grid-connected microgrid system in Room 20-102 at Cal Poly. A Photovoltaic Thevenin equivalent model was developed for the ITECH IT-M3633, but this setup failed …

Advancing Embedded Iot Architectures For Space And Terrestrial Applications, Wuwei Douglas Liu, Nicolas Jesus Alvarez, Eric Huang

Electrical Engineering

Radio transceivers play a pivotal role in establishing communication networks, particularly in regions where existing infrastructures are unstable or compromised due to natural disasters or conflicts. By utilizing LoRa (Long Range) communication technology, OWL Integrations develops radio transceivers to establish mesh networks to communicate with one another during disasters. This project team continues development of a second generation OWL board, classified as Quacker Advanced Development (QuAD), with a focus on transitioning to a new microcontroller and integrating GNSS libraries and drivers. An ulterior objective involved R&D for a space application of the board.

Ross Dam Micro Hydropower Project, Ryan Pospichal, Wilson Szeto

Electrical Engineering

In 2020, Utica Water and Power Authority (UWPA) commissioned the development and installation of a micro hydropower system for Ross Dam in northern California. The micro-hydro system was intended to serve as a reliable source of renewable energy to power on-site equipment for monitoring the Ross Reservoir. Despite its innovative approach, the system encountered operational shortcomings, including frequent mechanical failures, rapid wear, and an inability to adapt to variable flow rates. To address these challenges, UWPA has commissioned interdisciplinary teams of Mechanical Engineering (ME) and Electrical Engineering (EE) students to redesign the micro hydropower system. The ME team was entrusted …

X-Band Wireless Power Transfer System Using A Focused Array Lens, Jason Alexander Kunz, Tyler S. Bury, Oscar Damian Gonzalez, Jaime Garcia

Electrical Engineering

Wireless power beaming from space and energy harvesting were once stories of science fiction, until now. Wireless power transmission (WPT) is a field continually in development to provide energy in situations where energy transfer through wires is impractical or unfeasible. This engineering discipline abandons the use of wire technology for the energy transfer between the power source and a distant device. While various forms of WPT exist, our project focuses on transmission through means of radio frequency (RF), utilizing electromagnetic waves to power devices. Furthermore, WPT technology primarily assists in the elimination of a physical connection between devices, and it …

Design Of High Efficiency Doherty Power Amplifier, Kobi G. Kelly, Severin Pindell

Electrical Engineering

The project includes design and fabrication of a high efficiency power amplifier for a student design competition held at International Microwave Symposium (IMS) 2023. Efficient power amplifiers are critical for base station communication requiring efficient use of available power. The final design optimizes power added efficiency (PAE) and linearity. The amplifier will operate at 2.45 GHz. Competitive PAE above 50%, and C/I above 30 dB is achieved by leveraging a Doherty class amplifier using accurate discrete CGH4006P transistor models to simulate an efficient and linear design. Unique design features include optimal transistor bias point selection and power split ratios between …

A 4-Switch Buck-Boost Dc/Dc Converter For Electric Vehicle Applications, Andrew Hudak, Ashley Schiller

Electrical Engineering

In this project, we develop a four switch buck-boost DC/DC converter that is to be integrated into a microgrid-inspired power distribution architecture for electric vehicles. The overall architecture includes DC/DC and DC/AC converters for bi-directional energy transfer between the DC and AC ports along with a communications port to control each energy interface. There is also the onboard battery and the internal combustion engine power exchange being done with DC/DC converters and AC/DC inverters to connect to the centralized DC bus. Hardware prototypes using an Arduino and Raspberry Pi for the 500 W DC/DC and DC/AC converters have been previously …

2024 Marine Energy Collegiate Competition, Nora Riedinger, Miles Mikkelsen, Brendan Stratford, Derek Tom, Zach Kwast, Harmon Yanikian-Sutton, Kennedy Urcelay, Tori Thomas, Brady Caron

Mechanical Engineering

PolyWave Energy is the second team from California Polytechnic University at San Luis Obispo to compete in the Marine Energy Collegiate Competition. PolyWave Energy consists of Mechanical Engineering, Electrical Engineering, and Business Administration students who have worked together from September 2023 to May 2024 on designing, building, and testing a marine power device to serve a selected market.

In response to the escalating concerns surrounding carbon emissions, climate change, and the depletion of fossil fuels, California Polytechnic State University’s Polywave Energy team has developed a sustainable and reliable energy source for Autonomous Underwater Vehicle (AUV) charging. Through extensive research of …

Electrical Design For Moringa Leaf Dryer, Jake Weiss

Construction Management

The objective of this project is to provide a methodology to the electrical scope of mechanical leaf dryers. This dryer was particularly designed for an off-grid farm in New Longoro, Ghana in which resources and materials are limited. The electrical system must be designed so that it works with motors, variable frequency drives, worm gears, and other materials that could be sourced in Ghana. The system should also draw minimal power so that remaining photovoltaic energy could be utilized on the farm. The system should be simplistic and repeatable for other farmers to utilize. By using both a numerical analysis …

Design And Analysis Of A New Buck-Boost Converter With A Low-Side Switch, Abdullah Awidah

Master's Theses

This work explores the design, simulation, construction, and analysis of a novel Non-isolated DC-DC Buck-Boost converter which has the advantage of incorporating a low-side switch compared to the traditional buck-boost which requires a high-side switch. This allows the use of a low-side driver which further simplifies the design and operation of the converter. The proposed Buck-Boost converter was constructed to provide -24 V output from an input range of 12V-18V with 15V nominal input at 10W maximum output power utilizing 500kHz switching frequency. Findings from simulations and hardware tests verify that the converter effectively provides the desired -24 V output …

A Hybrid Computer To Solve The Selective Harmonic Minimization Problem In Single-Phase Inverters, Dillon Nguyen

Master's Theses

Power electronics possess forms of non-ideality due to the nonlinearity present in physical switches. These switches are driven with pulse width modulation (PWM), which properly down-converts or up-converts based on converter topology. When these switches turn on or off, they introduce the main proponent of efficiency loss: harmonics. This becomes a nonlinear optimization problem with many converters. The solution proposed in this thesis is an analog/digital hybrid computer that utilizes the speed of analog computation and the accuracy of digital computing together. A Plexim RT Box provides the programmability needed for algorithms, while the analog circuit provides low-power, high-speed computation …

Design Of A Dynamic, Reconfigurable, Self-Balancing Battery Pack, Alexander Hallett Neiman

Master's Theses

This thesis details the design and testing of a reconfigurable battery array. Reconfigurable battery arrays, specifically for mobile applications, have the potential to reduce or eliminate use of auxiliary charging, balancing, and inverter systems. Design work included a bidirectional solid state switch and a cell-to-cell bidirectional current-limiting power converter. While the overall efficiency, size, and cost of the battery pack was not competitive with existing options, it demonstrated cell-to-cell balancing and native four-level square wave AC inverter output with an array of only two cells. This demonstrates viability of the concept as well as reveals important requirements and safety features …

Improvements Of Hybrid Ac/Dc House Prototype, Arden Abude

Electrical Engineering

This is an iteration from previous designs of the Hybrid AC/DC House with a systematic addition of a portable AC power supply unit. This iteration for the Hybrid AC/DC House is an innovation of independence for sustainable housing solutions. It will serve as an alternative for rural communities needing power to rely on self-sustainable microgrids rather than large-scale AC electric grids. The addition of a portable AC power supply would allow the microgrid to remove its reliance on AC power from the larger grid and would elevate the system to complete energy independence. The microgrid has DC power generated from …

Design And Analysis Of Zero Voltage Switching Hybrid Voltage Divider, Stephen Ulysses Alvarado Estrada

Master's Theses

This work explores the design, construction, and analysis of a novel DC-DC converter which incorporates combinations of switching capacitors and inductors to achieve an integer voltage divider function, without the need for a feedback loop controller to achieve the desired output voltage. The proposed Hybrid Voltage Divider additionally provides zero voltage switching (ZVS) at turn on transitions which yields improved overall efficiency of the converter. Besides a proof-of-concept via computer simulations, another primary goal of this thesis is to demonstrate the functionalities of the proposed Zero Voltage Switching Hybrid Voltage Divider (ZVS-HVD) through hardware prototyping. The proposed ZVS-HVD was designed …

Hybrid Wall Outlet For Ac Or Dc Power Delivery, Garrett Knoller, Kerr Allan, Greg Perini

Electrical Engineering

The goal of this project is to develop hybrid DC and AC wall outlets for an efficient, flexible power interface. A DC plug standard is also proposed to allow DC devices to be safely powered by the outlet with the correct DC voltage for each device. The primary objective is to create a power outlet compatible with the proposed DC plug as well as NEMA 5-15 AC plugs, enabling the same outlet to power both types of load as needed. The outlet is intended for buildings and systems transitioning to an isolated DC grid to encourage DC development and adoption. …

Dc To Ac Inverter For A Microgrid-Inspired Power Distribution Architecture For Electric Vehicles, Bryan A. Carrillo Martinez, Eli Blacklock, Paul A. Samson, William S. Holt-Hillis

Electrical Engineering

This project builds upon the prototyping of a microgrid-inspired power distribution architecture for electric vehicles (EVs). The efficacy of this prototype aims to inform a full-scale power distribution system that charges an EV battery, supports the electric grid with important ancillary services, performs peer-to-peer EV charging, and works in conjunction with other AC and DC sources and loads. The scope of this report focuses specifically on the design, construction, and testing of the DC/AC inverter. Future development of this distribution architecture will incorporate synchronous generators, a battery management system, and an Arduino/Raspberry Pi-based communication system to fully simulate an electric …

An Analysis On Wildfire Mitigations Employed By Utilities In California, Evan Luu

Master's Theses

As climate change continues to worsen, environmental effects are felt by many people around the world. In California, some of its most damaging wildfires have been found to be started by utilities. As the state continues to suffer from worsening wildfire conditions, the utilities need to implement a variety of wildfire mitigations to help reduce the risk of wildfires that can affect the state and its residents. This paper analyzes the effectiveness of four mitigations employed across three California utilities and suggests potential ways for the mitigations to be used together. The technologies evaluated are covered conductor, rapid earth fault …

Paired Storage Distributed Energy System Design For A Local Community Farm, Neil Albert Collison, Lily Goldman

Electrical Engineering

This project considers the design of a renewable energy microgrid for a 19-acre community farm in San Luis Obispo, CA as the farm seeks to increase the magnitude of its electrical loads, and gain back-up electrical capability. The microgrid design will enable lower carbon emissions, reduce demand on the utility grid while saving on energy costs, and provide improved reliability and resiliency to the operator of the community farm. The eventual implementation of the design by a professional engineering entity will allow the community farm to expand its education program to include renewable energy as well as gain notoriety in …

Power Thyristor Controller For Speed Control Of Dc Motor, Alejandra Zapata, Morgan Erich Boehme, Abdullah Mohammed Awidah, Payton Robert Chalstrom

Electrical Engineering

In this work, a Power Thyristor Controller for Speed Control of DC Motor has been developed with the purpose of replacing an existing simulation experiment, aiming to effectively implement the principle of learning by doing. The primary objective of the experiment setup is to illustrate the fundamental principles and operational mechanisms underlying the firing angle and controlled bridge rectifier. The new experiment is taking advantage of the existing FCRO4100 Single Phase Firing Board that was donated to the University by ENERPRO. The pre-programmed microcontroller is connected to the thyristor bridge rectifier that’s powered by 24VAC. Additionally, a DC motor will …

Development Of Cal Poly’S Hybrid Ac/Dc House, Eduardo Andres Muñoz, Giovanni Ramirez Angel

Electrical Engineering

The Hybrid House provides an example for what sustainable housing solutions could look like. It also functions as a potential solution to the current rural electrification issues many developing countries face. The use of a DC-DC MISO converter allows for combining multiple power sources into a single DC bus. The Hybrid House integrates the DC bus by employing the use of DC-DC converters for home use. This system may potentially improve the overall system efficiency by avoiding the losses associated with AC-DC converters. The use of the DC bus further leverages the Solar Panel renewable energy solution to become a …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Sydney F. Fultz-Waters, Jacob Krynock

Materials Engineering

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and …

Exploring The Potential Of Pavegen’S Kinetic Energy Generating Floor For Sustainable Energy Solutions: A Proposal For Cal Poly Slo, Brandon J. Cuneo

Construction Management

This paper proposes the installation of Pavegen's kinetic energy generating floors at Cal Poly’s campus as a sustainable energy solution. Pavegen has developed a pioneering technology that converts footsteps into clean and renewable energy. The versatility of these floors is demonstrated through successful implementations in various settings, such as transportation hubs and public spaces, generating power from foot traffic. Collaborations with Schneider Electric, installation at Dupont Circle, and integration at Heathrow Airport showcase the potential for sustainable urban infrastructure. This paper outlines research conducted on Pavegen and similar solutions, including communication with company representatives and examining proposed installation locations at …

Programmable And Modular Dc-Dc Converter, Joshua C. Hutchinson, Elijah M. Gordon

Electrical Engineering

This project considers the design, implementation, and testing of an open-source dc-dc converter for microgrid prototyping. Unlike conventional dc-dc converters that are proprietary and require specialist knowledge, and are usually designed for a single function, the proposed dc-dc converter will comprise of a programmable MCU and a Raspberry Pi (RPi) interface to allow less-skilled consumers to monitor and modify a power converting system. We will develop an open-source library that contains voltage control, current control, maximum power point tracking, and battery charge control profiles. Each library will be easy to implement through a GUI on the Raspberry Pi and will …

Tank Level Controller Plc Lab, Siddhi Upadhyaya, Teghvir Grewal

Electrical Engineering

The California Polytechnic State University San Luis Obispo’s Electrical Engineering Department is currently developing lab experiments for the new EE435 (Industrial Power Control and Automation) class. In order to support these efforts, fourth year Cal Poly students are expected to develop laboratory experiments that will be conducted during this new class for the semester system. The lab experiment focused on in this project is called the Tank Level Controller. This experiment will introduce EE 435 students to Schneider Electric Programmable Logic Controller (PLC) hardware and software, which is prominent in the automation industry.
This experiment will require students to develop …