Power and Energy Commons^™

Dc/Dc Converter For A Solar Module, Francine Therese A. Canal, Jesus Cruz, Juan Jose Gonzalez

Electrical Engineering

This project presents the design and implementation of a DC/DC power converter intended for photovoltaic (PV) modules with varying electrical output characteristics. Solar panels experience significant changes in output voltage and power due to variations in sunlight, temperature, and load conditions. To ensure reliable operation across a range of conditions, the proposed converter is capable of both step-up and step-down operation to accommodate solar modules with power ratings from 50 W to 450 W and open-circuit voltages between 10 V and 80 V. The system operates at load currents up to 10 A and provide a user-adjustable output voltage within …

Dc/Dc Converter For A Solar Module, Stella Uribe, Richie Zaragoza, Olivia Grace Tran, Phillip Tyler Rich

Electrical Engineering

This project focuses on the design and validation of a general-purpose DC/DC power converter intended for use with photovoltaic (PV) solar modules operating under variable environmental and loading conditions. Solar panels exhibit significant variation in output voltage, current, and available power due to changes in irradiance, temperature, and operating point, making direct connection to downstream loads impractical. The proposed system addresses this challenge by providing a single, user-adjustable regulated DC output capable of both stepping up and stepping down the solar module voltage. The converter is designed to interface with solar modules rated between 50 W and 400 W, with …

Stationary Bike Power/Efficiency Monitor, Paula J. Diaz, Pilar M. Cook, Danielle Rhind

Electrical Engineering

This project developed a real-time power and efficiency monitoring system for a SportsArt ECO-POWR stationary exercise bicycle. The goal was to measure rider mechanical power and electrical power delivered to the utility grid simultaneously, allowing the overall bike-to-grid efficiency to be calculated and displayed in real time. Rider power was measured using Garmin Rally ANT+ power pedals, while grid power was measured using a Yokogawa WT310E power analyzer. A Raspberry Pi 3 Model B+ synchronized both data sources, calculated efficiency, displayed live performance metrics through a graphical user interface, and logged measurement data to CSV files for later analysis. The …

Autonomous Rover Solar And Battery Management System: Team B, Karla Jazmin Lira Gonzalez, Paige Ambriz, Kunj Shah, Elhom Delasa Sheykhi

Electrical Engineering

This project focused on the software and printed circuit board (PCB) integration for Poly1Rover’s battery management system (BMS). Poly1Rover is a student organization dedicated to building a low-cost autonomous rover designed to operate on Mars. Since solar availability, temperature, and other conditions on Mars vary, the rover requires a reliable battery management system that accurately monitors battery health and status. This team’s work included the communication and control side of the BMS. The subsystem was designed around the Renesas ISL94202 battery monitor and the MSP430 controller. Battery information was read from the ISL94202 registers through I2C communication, converted from raw …

Design And Evaluation Of An Open-Source Ac/Dc Power Converter For Microgrid Applications, Ryan J. Rayos

Master's Theses

This thesis presents the design, implementation, and evaluation of an open-source bidirectional power conversion platform intended for microgrid applications. As distributed energy resources, battery storage systems, and hybrid AC/DC architectures continue to increase in adoption, there is a growing demand for flexible, low-cost, and programmable power electronic platforms capable of interfacing between DC and AC subsystems. Existing commercial solutions are often proprietary and expensive, limiting their accessibility for educational, research, and rapid prototyping applications. This work expands upon the existing open-source Atinverter platform by increasing its operating voltage capability, integrating bidirectional power flow, and implementing telemetry systems suitable for microgrid …

Maximum Power Point Tracking For Photovoltaic Cells, Rodrigo Menchaca-Ramirez, Jesus Martinez, Steven Rodriguez

Electrical Engineering

Unlike an ideal DC Power Supply, a solar panel does not operate with linear I-V Characteristics. The voltage and current characteristics of a solar panel change based on irradiance, temperature, weather conditions, and load demand. Because of these factors, solar panels do not always operate at their Maximum Power Point, which can lead to significant power losses. Maximum Power Point Tracking is used to adjust the panel operating point so that more usable power can be delivered to the load.This project developed a Maximum Power Point Tracking system using an STM32 Nucleo-L4A6ZG microcontroller and an LT8705A DC-DC converter stage. The …

Portable Food Pasteurization Using Pulsed Electric Fields (Pef), Thomas E. Mcmillan Iii

Electrical Engineering

Foodborne illnesses remain a significant public health concern, motivating continued development of alternative food pasteurization technologies. Pulsed electric field (PEF) treatment is a non-thermal pasteurization method that inactivates microorganisms through electroporation while minimizing thermal degradation of food products. The long-term objective of this project was development of a portable PEF food pasteurization system.

An iterative design approach was used to investigate generation of the high-voltage pulses required for PEF treatment. Multiple pulse forming network topologies were evaluated through simulation, leading to selection of a solid-state Marx generator architecture. A low-voltage five-stage prototype was designed, constructed, and tested to validate the …

Pv Performance Evaluation Study At Cal Poly Solar Farm, Eva Paola D. Calderon

Electrical Engineering

This photovoltaic (PV) system performance evaluation study aims to assess the performance of Cal Poly’s Gold Tree Solar Farm, which produces 4.5MW of solar energy. The evaluation concerns itself with the reliability of the PV system that can be affected by weather conditions, component malfunctions, and degradation of the PV modules. Under the International Energy Agency Photovoltaic Power Systems (IEA-PVPS) Task 13 objectives of reliability and maintenance, this study is necessary to contribute towards improvements in analysis and mitigation strategies for long term usage. Existing operational monitoring data from 2018 to 2025 is the focus timespan, providing real world data …

Lora Networking Hardware Reference Designs For Terrestrial And Low-Earth-Orbit Communications, Kevin Nottberg

Master's Theses

The work presented here demonstrates a highly robust and tested LoRa networking hardware reference design to meet the needs of the embedded networking company OWL Integrations. The hardware presented integrated a unique combination of features and design choices. The detailing of its unique design is potentially of use to others for use in fielded battery powered terrestrial sensor networking hardware utilizing LoRa. Also, the terrestrial hardware presented is shown to have the capability to support command and control (C2) LoRa links in low-earth orbit beyond terrestrial systems. The design presented has a more U.S. centric component bill-of-materials (BOM), with the …

Development Of A Multi-Mode Switching-Inverter Laboratory Module For An Introductory Power Electronics Course, Darcy Eliasi

Master's Theses

DC–AC converters, or inverters, are essential power‑electronic interfaces widely used in photovoltaic systems, microgrids, energy‑storage installations, and numerous other modern electrical applications. This thesis presents the design, construction, and testing of an improved laboratory module developed as a student learning tool for demonstrating four fundamental inverter switching techniques: simple square wave (SSWI), modified square wave (MSWI), bipolar PWM, and unipolar PWM. Building upon the previous module, the improved design centers on three key enhancements. These include the selection of a more suitable wave‑generation solution, a multiplexer‑based mode‑selection architecture that reduces user complexity and eliminates conflicting signal configurations, and the integration …

Sustainabake, Kevin Kunta Swanson Ii

Electrical Engineering

This senior project outlines the development of an oven that utilizes renewable energy to operate safely and effectively. It aims to test building an oven using mostly basic hardware students acquired during their time at Cal Poly and provide a starting point for those interested in creating a solar-powered oven. As our society continues to innovate and increasingly relies on electricity, it is important to place more emphasis on how we can make our lives sustainable to take care of our environment without introducing excessive pollutants. Food preparation is a daily activity that typically involves significant energy consumption, making this …

Time-Domain Symmetrical Components For Detection And Analysis Of Unbalanced Faults In Three-Phase Systems, Ryan Pospichal

Master's Theses

Unbalanced faults in three-phase power systems degrade performance, increase losses, and threaten equipment reliability. Traditional frequency-domain approaches using phasor analysis and symmetrical components offer valuable steady-state insights but respond too slowly for transient or rapidly changing conditions. This thesis investigates time-domain symmetrical components (ISCs) as a faster, physically interpretable method for detecting and analyzing unbalanced faults directly from instantaneous voltages and currents. Two ISC computation techniques were developed and compared: a polar-form method, applying one-third and two-thirds cycle time delays, and a rectangular-form method, which achieves equivalent phase shifts using only a quarter-cycle delay. Simulations in Microsoft Excel verified both …

Isolated Dc-Dc Converter For An Ev Microgrid, Oscar Yu, William Leiker

Electrical Engineering

This product is a redesign of a DC-DC buck-boost converter which utilizes a new topology, the flyback converter, for use in an electric vehicle (EV) as a microgrid. The main driver behind the redesign is to provide electrical isolation between elements in the microgrid. The EV microgrid consists of the battery, motor, external DC and AC ports, and the power electronics (DC-DC converter and AC-DC inverter) which were designed and built in previous senior projects. Using EV’s as microgrids can help relieve stress from the main power grid caused by charging electric vehicles. Implementing EV’s as a microgrid enables the …

Hands-On Microgrid Education: Using Programmable Dc-Dc Converters To Teach Power & Energy Systems, Alejandra Zuniga

College of Engineering Summer Undergraduate Research Program

This project will develop an analog computing circuit that can accelerate power system simulations used for grid interconnection studies. The project will leverage analog computing to create a specialized circuit capable of simulating large-scale power networks with detailed models of power electronics-based loads, such as those found in data centers and manufacturing plants. A software application programming interface will be developed to integrate this circuit with a desktop computer, where simulations can be run by the user. The project team will also work with industry partners and utilities to evaluate the feasibility of the proposed technology for conducting real-world grid …

Exopg Maturation And Owl Interface, Duncan Michael Louden

Electrical Engineering

The maturation of the ExOPG buoy generator consists of an interface to facilitate remote data acquisition of an existing battery charge controller. This module telemeters battery controller data including voltage, temperature, and state of battery charge. The data is transmitted to a communication system and is able to be viewed by humans on a 24/7 basis for continuous operation and human usage. The module works seamlessly as an addition to the existing ExOPG generator, and it does not interfere with any existing and planned components of the generator. The module is highly efficient and draws minimal power from the existing …

Design And Development Of A Half-Bridge Llc Resonant Converter Laboratory Module, Alyssa Lam

Master's Theses

Resonant DC-DC converters have become a well-known solution in power supplies due to their ability to improve efficiency by utilizing soft-switching techniques. This further has caused a growing interest in industry to use these converters for high-switching-frequency, high-efficiency, and high-power applications such as EV charging stations, photovoltaic systems, battery chargers, etc. One particular resonant topology that has gained popularity in recent years is the LLC resonant converter. Due to the prevalent use of the LLC resonant converter, it is therefore crucial for students preparing for a career path in power electronics to become well-versed in the concept and implementation of …

Open Source Microgrid Integration, Zachary J. Kwast

Master's Theses

Microgrids are small-scale electrical systems that operate in tandem with a centralized grid to provide power to a smaller group of target devices. These microgrids are used for a wide range of different purposes, which invites the need for a generalized model that can be tweaked for a variety of uses. This document goes over the theory used to design an open source AC and DC microgrid meant for use by anyone. The microgrid is created using a Raspberry Pi that controls two different power converters so that a wide range of voltage and current characteristics can be achieved. These …

Expeditionary Ocean Power Generator, Ethan Gossard, Julian Steele, Alex Gray, Hunter Herring-Alderete

Electrical Engineering

Point Absorber Wave Energy Converters are currently being explored as a new form of energy harvesting. The Naval Facilities' Expeditionary Ocean Warfare Center (NAVFAC EXWC) has commissioned an interdisciplinary project for students at California Polytechnic State University, San Luis Obispo, to design a prototype Expeditionary Ocean Power Generator (ExOPG) for charging batteries in the ocean.

The Mechanical Engineering team is responsible for assembling the prototype chassis, which converts the vertical bobbing motion of a buoy into kinetic rotational energy that can be used to rotate a generator shaft. They are additionally tasked with isolating the electrical components from the harsh …

Piezoelectric Actuator Driver System, Daniel Hoefer

Electrical Engineering

This work presents the design, fabrication, and testing of a high-voltage piezoelectric actuator driver system purposed for integration into defense and aerospace precision motion control applications, particularly those in laser optics. The core challenge addressed was the mismatch between the standardized 28V DC power bus used in military systems and the significantly higher voltage requirements of piezoelectric actuators. Existing commercial drivers were evaluated and found unsuitable for field deployment due to inadequate ruggedness, excessive complexity, or power limitations. Consequently, a modular system architecture was designed featuring four independent driver channels, each using a high-voltage, high-current linear amplifier topology to scale …

Marine Energy Collegiate Competition - Polywave Energy, Beneda Loya, Isaiah Martinez, Emily Nicoletta, Michael Weber

Electrical Engineering

This document is the final Electrical Engineering senior project report for Cal Poly’s 2025 Marine Energy Collegiate Competition (MECC) team. The goal of this project is to build and test a wave-energy converter designed to address the need for sustainable power generation for remote coastal community microgrids. These existing systems often rely on costly, fossil-fuel generators, creating both logistical and environmental challenges. Our device aims to provide a renewable, low-maintenance solution that can operate reliably in offshore environments and serve commercial or research applications. The goal of the electrical engineering team was to develop a system that can convert rotational …

Advanced Light Dimming Power Converter, Jaden Nguyen, Edwin Lin, Alan Thai

Electrical Engineering

This senior project discusses and follows the development of the Advanced Light Dimming Power Converter meant to modernize the power electronics curriculum and improve student safety for a lab. The power converter attempts to replace the original experiment which includes a traditional TRIAC-based dimmer and focuses on demonstrating phase angle control for incandescent light bulbs. However, several drawbacks including high-voltage exposure and outdated technology warranted a revamp. The redesigned module includes a dual-experiment setup with an updated TRIAC-based dimmer circuit and a new AC-DC LED driver circuit with constant current control and PWM dimming capability. Both systems have been fabricated …

Design, Analysis, And Implementation Of An Improved Zero Voltage Switching Hybrid Voltage Divider, Luke V. Cerda

Master's Theses

This thesis entails the study, design, and construction of a novel DC-DC converter topology, the Zero Voltage Switching Hybrid Voltage Divider (ZVS-HVD), with improved modularization, optimization, and compactness. The ZVS-HVD facilitates higher load currents and accomplishes DC-DC voltage division through switching inductors and capacitors. Low switching loss is achieved through zero voltage switching (ZVS) and the use of GANFET switches. An analysis of duty cycle and high-frequency operation is conducted, enabling 1 MHz switching and improvements in output voltage ripple, voltage drooping, board size, and efficiency at higher load currents. Two versions of ZVS-HVD prototypes were constructed with on-board signal …

Hydropower Collegiate Competition, Aiden D. Foster, Devon Bountry, Joanna Vo, Timothy Rinker, Amanda Rodriguez, Minh Nguyen, Eli Haushalter, Sophie Watkinson, Maiya Holton, Breanne Evans

Mechanical Engineering

The Cal Poly SLO HCC team presents a feasibility study and engineering design review package for retrofitting the non-powered Ritschard Dam in Colorado into a hydroelectric facility as part of the 2025 Hydropower Collegiate Competition. Through a rigorous and multi-staged assessment of plausible dam sites in the western US, the team has chosen the Ritschard Dam in Colorado to implement an electromechanical component designed to accommodate a large range of flowrates stemming from a large variance in upper reservoir capacity due to geographical and climate effects. The team evaluated non-powered dams based on technical feasibility, electric grid proximity, power generation …

Improvements To Cal Poly's Hybrid Ac/Dc House, Brandon Ng, Andrew Nguyen, Logan Tom

Electrical Engineering

This senior project details the improvements made to Cal Poly’s Hybrid AC/DC House project. The previous state of the house experienced issues with proper reading of the current power being drawn from the connected AC sources, as well as with the system’s multiple-input single-output converter, where thermal overheating of specific FETs prevented the system from reaching its maximum output power. The updates made to the AC/DC house include improved code to prevent faulty readings and display failure and a cleaned-up power monitoring board that removes noisy signals and allows for the correct power implementation to be displayed. In addition, the …

Compact Modular Photovoltaic System With Mppt Controller, Alain Ardash Kanadjian, Alex Aarnio, Christopher Arango

Electrical Engineering

Energy demands have been on the rise, as environmentally harmful power generation systems stay popular due to lower costs and compact designs compared to renewable energy infrastructure. We challenge this problem with a modular photovoltaic microgrid system for power generation in underutilized spaces. The Maximum Power Point Tracking (MPPT) charge controller employed is low-cost and power efficient. This controller monitors energy generation and usage in real time, with data logging through an online user-friendly interface. With support for a variety of solar panel and battery configurations, this scalable system helps provide a cost and space efficient solution to clean energy …

Development Of A Modular Dual-Phase And Single-Phase Buck Converter Laboratory Module, Maxwell John Kreizinger, Ethan David Robson

Electrical Engineering

This senior project entails the design, creation, and testing of a circuit board to exhibit the differences and advantages of the multiphase buck converter over the single-phase buck converter for use in a future power electronic laboratory experiment at Cal Poly State University. As energy demand requirements continually increase from more advanced and widespread use of technology, it is important to find a method of power delivery that maximizes efficiency while taking up as little area on a circuit board as possible. This is where the multiphase buck converter topology is desirable over the traditional single-phase buck converter topology. For …

Development Of A Versatile Switching Mode Inverter Laboratory Module, Zachariah Lee Mustar

Master's Theses

DC-AC converters, or inverters, are complex devices that play an essential role in photovoltaic, energy storage, and microgrid systems. Therefore, they constitute a class of power electronics that any power-focused electrical engineering student should be familiar with. This thesis presents the development and testing of a single device that power electronics students will use in a laboratory setting to experiment with each of the four different switching techniques employed in inverters: a simple square wave (SSWI), modified square wave (MSWI), bipolar PWM, and unipolar PWM. The module was built with a physically modifiable control stage and a power stage constituting …

Study On The Application Of Smart Electric Meters For Secondary Voltage Protection, Jayaditya Sisodia

Master's Theses

The purpose of our research is to utilize PG&E’s Smart Meters installed across California to protect the Secondary Voltage delivered to the meter. This means detecting electrical faults between the utility’s distribution transformer and the installed Smart Meter. Our goal is to propose and implement various solutions through additional devices and protocols to detect and prevent these faults, communicate them with the meter, and forward fault information to the utility. A device will be designed to be installed on the transformer, detect faults, shut off power transmission, and communicate to the meter via fiber optic cable. Research will then be …

Remote Monitoring And Control Of Protection Relays Via Programmable Logic Controller, Rio Mcgown-Kauffman

Master's Theses

The purpose of this study is to explore the ability of a programmable logic controller (PLC) to wirelessly monitor and control power protection relays. The technologies surrounding power protection and industrial automation are ever evolving and have developed significantly in recent history. Industrial power applications call for consistent condition monitoring and status updates for various high-importance components. The high-importance components have power protection schemes that are managed by digital relays to trip circuit breakers in fault or unsafe operating conditions. The smart relays have a wide range of capabilities, including communications. Cal Poly assembled a collection of relays from Schweitzer …

Modeling Battery Energy Storage Systems To Study The Effects Of Battery Chemistry And Operation On Power Quality, Lin E. Knudsen

Master's Theses

This thesis studies the impacts of battery chemistry (specifically lithium-iron phosphate, sodium-ion, and solid-state), AC voltage, battery size, charging mode, state of charge (SOC), active power draw, and power factor on the power quality of a Battery Energy Storage System (BESS). For harmonic evaluation, the metrics provided by the IEEE Standard 519 are used as a guideline to quantify voltage and current harmonics. A comprehensive MATLAB Simulink using Simscape Electrical is used to develop and simulate the models for the battery, DC-DC converter, AC-DC converter, and the grid. A total of 57 simulation cases varying the BESS factors are performed, …