Power and Energy Commons^™

Preparation And Electrochemical Performance Of Mo-Doped Li3V2(Po4)3/C Cathode Materials, Zhi-Yuan Tang, Wei Yuan, Ji Yan, Wen-Feng Mao, Li Ma

Journal of Electrochemistry

The molybdenum-doped Li₃V_2-xMo_x(PO₄)_3/C (x = 0.01, 0.02 and 0.03) cathode materials were prepared with a sol-gel method by using Li₂CO₃, NH₄H₂PO₄, V₂O₅ and MoO₃ as raw materials, and citric acid as both chelating reagent and carbon source. The X-ray diffraction (XRD) analyses showed that the crystal structure of as-prepared samples is monoclinic with space group P2₁/n. Scanning electron microscopy (SEM) observations indicated the uniform morphology for Li₃Mo_0.02V_1.98(PO₄) …

Synthesis And Electrochemical Properties Of Lifeso4F/Graphene Composite As Cathode Material For Lithium-Ion Batteries, Wei Guo, Ya-Xia Yin, Li-Jun Wan, Yu-Guo Guo

Journal of Electrochemistry

The LiFeSO₄F was successfully synthesized from the reactions of FeSO₄∙xH₂O (x=1, 4, 7) with LiF in tetraethylene glycol media through a facile low temperature method. The structures and microscopic features of the products were characterized by XRD, SEM and TEM. TGA result shows the good thermal stability of the as-prepared LiFeSO₄F. No diffraction peaks of the FeSO₄ are observed in the as-prepared products with the starting material of either FeSO₄∙4H₂O or FeSO₄∙7H₂O, which should be ascribed to delaying the release of H_{2 …}

Buffering Pv Output During Cloud Transients With Energy Storage, Yacouba Moumouni

College of Engineering: Graduate Celebration Programs

The Problem

• Photovoltaic output power can be affected by many factors including clouds passing overhead.

• Utilities in generally prefer a guaranteed power delivery level over some specified power delivery period.

• Power delivered during peak demand hours is generally more valued by utilities. For the Desert Southwest this is in the summertime afternoons. For the local area this will be defined as 1-5 pm for the three summer months.

• While battery power can be adapted to this problem, large batteries to be expensive.

Preparation And Electrochemical Performance Of Lifepo4/C By Spray Drying Method Assisted With Organic Template, Quan-Bing Liu, Yang-Mei Jiang, Hui-Yu Song, Shi-Jun Liao

Journal of Electrochemistry

In this work, the LiFePO₄/C composites were prepared by the spray drying and carbothermal method, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge measurements. The effects of the organic assisted templates on the morphologies and electrochemical properties of the LiFePO₄/C composites were investigated. The results showed that the morphology and microstructure of the composites could be tuned by incorporating with the different templates. The morphology of the composite appeared to be solid microspheres if no organic template was added, while porous microspheres, nest-like …

Synthesis And Electrochemical Performance Of Xlifepo4·Yli3V2(Po4)3 Composites, Ping-Ping Ma, Zhi-Jian Liu, Jian-Hua Xia, Yu Chen, Pu Hu, Zhi-Chao Lu, Ding-Guo Xia

Journal of Electrochemistry

A series of xLiFePO₄·yLi₃V₂(PO₄)₃ composites were systematically synthesized through solid state reactions by variations in the proportions of LiFePO₄ and Li₃V₂(PO₄)₃. The properties of the prepared compounds were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The capacity of 162.7 mAh/g at 0.2 C rate was obtained with the relatively good cycle stability and good conductivity for 0.95LiFePO₄·0.05Li₃V₂(PO₄)₃ due to more uniformed distributed and smaller particle sizes.

Preparation And Characterization Of Mno/Tin Anode For Lithium Ion Batteries, Gao-Jie Xu, Hai-Yan Yang, Peng-Xian Han, Li-Xue Zhang, Ke-Jun Zhang, Chuan-Jian Zhang, Yu-Hua Fan, Cai-Feng Bi, Guang-Lei Cui

Journal of Electrochemistry

Manganese titanate (MnTiO₃) powder was prepared via a sol-gel method using manganese acetate and tetrabutyl titanate as raw materials, and citric acid as a chelating agent. Through high temperature nitridation of MnTiO₃ powder in ammonia, the MnO/TiN composite was obtained. The phase structure, composition and morphology of the composites were characterized by XRD, SEM and EDS. The electrochemical properties of the composite electrodes were studied by performing cyclic voltammetry, galvanostatic charge and discharge, and electrochemical impedance spectroscopy tests. The MnO/TiN electrode delivered specific capacities of 394 mAh·g^-1 and 146 mAh·g^-1 at the current density of …

Progress And Perspective Of Fuel Cell Technology, Ming Hou, Bao-Lian Yi

Journal of Electrochemistry

Fuel cell, a clean and high-efficiency electrochemical power source, has being paid much attention worldwide recent years. In this paper, the progress and perspective of fuel cell technology are elucidated in detail. Fuel cells have been applied in some special fields such as spacecraft, shuttle and submarines. However, in the areas of transportation, stationary station and portable power source, fuel cells are still under demonstration due to the durability and cost problems. The reliability and surrounding survivability of fuel cells should be enhanced in the special application. Meanwhile, the durability and cost of fuel cells are the main issues to …

The Electrocatalytic Study Of Licoo2 In Air Electrode For Lithium-Air, Jun Gao, Wei Wu, Yan-Yan Tian, Yong Yang

Journal of Electrochemistry

The LiCoO₂ has been investigated as a new electrocatalyst for air electrodes using homemade lithium-air battery. The electrochemical performance and structural changes of the LiCoO₂ based composite air electrodes have been studied. The results of CV, XRD and charge-discharge tests show that the composite air electrodes composed of LiCoO₂ can greatly improve the discharge performance of lithium-air batteries. In particular when the composite air electrodes are charged to 4.1 V before further discharging, the obvious catalytic effects of LiCoO₂ are attributed to higher valence state of the Co element in LiCoO₂, esp. at charged …

Dissolved Oxygen Seawater Battery With Electrochemical Capacitance, Hai-Bo Xu, Yong-Hong Lu, Wei Zhang, Yan-Ting Yu, Chuan-Wei Yan, Ya-Ping Sun, Lian Zhong, Jian-Guo Liu, Yi Zheng, Bing Han, Yong-Liang Wang

Journal of Electrochemistry

A new concept of seawater battery with electrochemical capacitance (SWB-EC) has been proposed using carbon fibre brush (CFB) as the cathode material, and three testing prototypes have been made accordingly. The discharge performances of the CFB before- and after-oxidation and Mg alloy sacrifice anode were studied by cyclic voltammetry and constant current discharge tests under steady state conditions. Results show that the oxidized CFB exhibits the pseudo-capacitive characteristic and its activity of oxygen reduction reaction (ORR) in stirred seawater highly increases, comparing with the non-oxidized CFB. The open circuit potential of Mg alloy sacrifice anode is -1.74 V, having the …

Slides: Jisea Natural Gas Study: Potential U.S. Electric Power Futures, Jeffrey Logan

Drawing the Blueprint for a Sustainable Natural Gas Future (January 18)

Presenter: Jeffrey Logan, Denver Museum of Nature and Science

4 slides

Technical Feasibility Of Storage On Large Dish Stirling Systems, Charles E. Andraka, K Scott Rawlinson, Nathan P. Siegel

Faculty Journal Articles

Dish-Stirling systems have been demonstrated to provide high-efficiency solar-only electrical generation, holding the world record at 31.25%. This high efficiency results in a system with a high possibility of meeting the DOE SunShot goal of $0.06/kWh. Current dish-Stirling systems do not incorporate thermal storage. For the next generation of non-intermittent and cost-competitive solar power plants, we propose a thermal energy storage system that combines latent (phase-change) energy transport and latent energy storage in order to match the isothermal input requirements of Stirling engines while also maximizing the exergetic efficiency of the entire system. This report takes an initial look at …

In Situ And Ex Situ Studies Of Molybdenum Thin Films Deposited By Rf And Dc Magnetron Sputtering As A Back Contact For Cigs Solar Cells, K. P. Aryal, H. Khatri, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Molybdenum thin films were deposited by rf and dc magnetron sputtering and their properties analyzed with regards to their potential application as a back contact for CIGS solar cells. It is shown that both types of films tend to transition from tensile to compressive strain when the deposition pressure increases, while the conductivity and the grain size decreas. The nucleation of the films characterized by in situ and real time spectroscopic ellipsometry shows that both films follow a Volmer-Weber growth, with a higher surface roughness and lower deposition rate for the rf deposited films. The electronic relaxation time was then …

Measuring And Filtering Microwave Radiations Using Frequency Selective Surface Through Energy Saving Glass, Irfan Ullah

Theses: Doctorates and Masters

This thesis presents the results of our investigation into the measurement and filtering of microwave radiation, and the subsequent development of a microwave reduction solution for modern building architecture utilising Energy Saving Glass (ESG), in conjunction with Frequency Selective (FSS) surfaces through which useful signals can be filtered. In the investigation, radiation power density levels arising from the three common microwave sources (radio base stations, mobile phones, and microwave ovens) were measured, and the results were compared with the standards provided by the Australian Radiation Protection and Nuclear Safety Agency. For the radio base stations, the relationship between radiation intensity …

Distributed Solar Photovoltaic Grid Integration System : A Case Study For Performance, Ming Shen

Dissertations and Theses

The needs to the sustainable development of electricity, energy efficiency improvement, and environment pollution reduction have favored the development of distributed generation (DG). But the problems come with increasing DG penetration in distribution networks. This thesis presents the Solar Energy Grid Integration System (SEGIS) Stage III project done by Portland General Electric (PGE), Advanced Energy, Sandia National Lab on a PGE selected distribution feeder. The feeder has six monitored commercial solar PV systems connected. The total power output from the PV systems has the potential to reach 30% of the feeder load. The author analyzes the performance of the solar …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang

Journal of Electrochemistry

Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …

The Electrochemical Properties Of Cathode Materials LimXV3-XO8, Hui Yang, Gang-Gang Zhao, Juan Li

Journal of Electrochemistry

The cathode material of LiM_xV₃-xO₈ was fabricated by sol-gel method using citric acid as a chelating agent and doping transition metal ions M (Mn, Ti, Co and Ni). The structure, morphology and electrochemical proprieties of the LiMxV3-xO8 samples were investigated by XRD, TGA/DTA, SEM, charge-discharge and CV measurements. The results showed that different calcining temperatures result in different structures and morphologies, which lead to different discharge capacities. The specific discharge capacity of the sample calcined at 500℃ for 6 h was up to 300.4 mAh/g in the first cycle, and the capacity decreased with the …

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu

Journal of Electrochemistry

A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)₆ was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)₆ crystals were effectively controlled by adjusting the volumn ratio of H₂O and CH₃CH₂OH solvents. Perovskite CaSnO₃ could be obtained by calcination of CaSn(OH)₆ at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO₃ electrode.

Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi_0.6Fe_0.4O_3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi_0.6Fe_0.4O_3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi_0.6Fe_0.4O_3-δ/ScSZ/LaNi_0.6Fe_0.4O_3-δ sintered at 1050°C was the smallest (0.70Ω·cm², 0.27Ω·cm^{2 …}

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm² in Fe(Ⅲ)-oxalate-calcium gluconate system.

Study On Residual Powders Of Lithium-Ion Batteries With Different Voltages After Explosion, He Li, Zhi-Kui Chen, Ji-Na Cao, Guang-Chuan Liang

Journal of Electrochemistry

The residual powders of lithium-ion batteries at different voltages after explosion were obtained by using the battery impact testing machine. And these powders have been investigated by weighing, water solution and X-ray diffraction (XRD). The results showed that the integrity status of copper current collector and weight of residual powders decreased gradually with increasing of battery voltage, rising of burning temperature and releasing of burning duration time. The residual powders could be separated to insoluble powders and soluble powders by the water solution. The proportion of the insoluble powders is more (about 90%) including C, Co and CoO, while the …

Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO₂ particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO₂ in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.

Study On The Fluorescent Carbon Nanodots With Electrochemical Methods, Bao-Ping Qi, Yan-Min Long, Lei Bao, Cui Liu, Zhi-Ling Zhang, Dai-Wen Pang

Journal of Electrochemistry

Carbon nanodots are a new class of fluorescent nanoparticles with a carbon-based core, which possess wavelength-tunable luminescence, high photostability, resistance to photobleaching, water-solubility, and ease of bioconjugation. Owing to their attractive merits, carbon nanodots like other carbon nanomaterials such as fullerene, carbon nanotubes and graphene, have attracted much attention. In addition, carbon nanodots can be inexpensively produced by electrochemical methods with simple post-processing under mild conditions. Electrochemical approaches have unique advantages in the analysis of surface structures and luminescence mechanism of materials. In this review, recent advances in electrochemical methods used for the synthesis and luminescence mechanism of fluorescent carbon …

Effects Of Graphene On Electrochemical Behaviors Of Ni(Oh)2 As Supercapacitor Material, Zhen-Zhen Zhao, Wen-Bin Ni, Neng-Yue Gao, Hong-Bo Wang, Jian-Wei Zhao

Journal of Electrochemistry

The enhanced electrochemical properties of Ni(OH)₂ by the oxidation defected graphene were studied by both experimental method and theoretical calculation. The composite material of nano-Ni(OH)₂/graphene was prepared by potentiostatic deposition on the graphene substrate. Observed by TEM, the Ni(OH)₂ nanoparticles were well dispersed on the graphene substrate with the diameter of 5.0±0.5 nm. The capacitance of the system measured by the electrochemical test was 1928 F·g^-1. As indicated by the theoretical calculations, the composite material becomes conductive since Ni(OH)₂ is combined with surface functional groups of the graphene through the strong chemical interaction. …