Power and Energy Commons^™

Exploring The Potential Of Pavegen’S Kinetic Energy Generating Floor For Sustainable Energy Solutions: A Proposal For Cal Poly Slo, Brandon J. Cuneo

Construction Management

This paper proposes the installation of Pavegen's kinetic energy generating floors at Cal Poly’s campus as a sustainable energy solution. Pavegen has developed a pioneering technology that converts footsteps into clean and renewable energy. The versatility of these floors is demonstrated through successful implementations in various settings, such as transportation hubs and public spaces, generating power from foot traffic. Collaborations with Schneider Electric, installation at Dupont Circle, and integration at Heathrow Airport showcase the potential for sustainable urban infrastructure. This paper outlines research conducted on Pavegen and similar solutions, including communication with company representatives and examining proposed installation locations at …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.

Optimizing Llrf Parameters In The Electron-Ion Collider, William M. Bjorndahl

Physics

To improve particle interaction in the future Electron-Ion Collider (EIC), we investigated different feedback implementations to control the accelerating voltage and examined the power and beam phase for each instance. Using MATLAB, we studied three feedback mechanisms: Direct, One Turn, and Feedforward. Enacting feedforward yielded the best performance. To minimize the klystron power consumption, we analyzed different Low-Level Radio Frequency (LLRF) parameters such as detuning. Combining theory and simulated results, we found the optimal detuning value that minimizes klystron power consumption.

Solar Powered Single-Axis Heliostat Active Solar Tracking Device, Mason Kyle Roberts

Physics

As a means of cooking food, the burning of biomass accounts for over 4 million premature deaths in third world countries (“Household Air Pollution and Health”). The focus of this project was to explore an alternative that could utilize focused sunlight to cook food. A solar tracker was designed to be affixed to a parabolic, reflective, tilted single axis heliostat to follow the sun throughout the day and focus the reflected light to the bottom of a cooking surface. This surface became hot enough to for the preparation of food or boiling/sterilization of water.

A goal for each project was …

A Prototype Microwave Cavity Control Circuit For Use In Next Generation Free Electron Laser, Josh Thompson, Peter Neal Barrina, Jiayi Jiang, Joe Frisch, Steve Smith, Daniel Van Winkle

STAR Program Research Presentations

One of the current programs at SLAC National Accelerator Laboratory is the Linac Coherent Light Source, or LCLS. Using the existing hardware of the last third of their linear accelerator (or “linac”), SLAC has created one of the most energetic X-ray free electron lasers (or “FEL”). Since 2009, LCLS has used this FEL to perform a wide range of experiments across all sciences, most notably ultrafast filming at the molecular scale. As requests for beam-time with this laser increases, SLAC is purposing a linac upgrade to better match this demand. This upgrade, named LCLS-II, will replace existing copper radio frequency …

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Morphology Changes In Pcpdtbt:Pcbm And P3ht:Pcpdtbt:Pcbm And Its Effect On Polymer Solar Cell Performance, Galen David Cauble

Physics

Polymer solar cell morphology is sensitive to both heat and time. By thermally annealing polymer solar cells the morphology of the devices can be altered causing immediate changes in device performance. Blending PCPDTBT:PCBM with P3HT:PCPDTBT combines the absorption characteristics of each to create a more even absorption spectrum. Subjecting PCPDTBT:PCBM, and P3HT:PCPDTBT:PCBM polymer solar cells to thermal annealing as well as recording device performance through time has shown that P3HT:PCPDTBT:PCBM devices react positively to thermal annealing (increasing from 0.8% to 1.4%) while PCPDTBT:PCBM devices have varied reactions. Furthermore, the P3HT:PCPDTBT:PCBM devices have achieved efficiencies of 1.6% in AM 1.5 compared …

Android Application Controlled Surge Protector, Lok An

Electrical Engineering

A significant amount of consumer electronics cannot be switched off completely without being unplugged. Standby power, also known as phantom power, refers to the electric power consumed by electronic appliances when they are switched off. There are some devices that need constant power; items like alarm clocks and security systems need constant power to function correctly. Some devices, such as video game consoles and televisions, consume power without offering any features. Electricity lost from standby power has been increasing with the amount of consumer electronics increasing in households.

This project’s goal is to create a low power remote that can …

Asynchronous Mips Processors: Educational Simulations, Robert L. Webb

Master's Theses

The system clock has been omnipresent in most mainstream chip designs. While simplifying many design problems the clock has caused the problems of clock skew, high power consumption, electromagnetic interference, and worst-case performance. In recent years, as the timing constraints of synchronous designs have been squeezed ever tighter, the efficiencies of asynchronous designs have become more attractive. By removing the clock, these issues can be mitigated. How- ever, asynchronous designs are generally more complex and difficult to debug. In this paper I discuss the advantages of asynchronous processors and the specifics of some asynchronous designs, outline the roadblocks to asynchronous …

Optimization Of P3ht-Pcbm Polymer Solar Cells Through Device Simulation And Manufacturing, James Boom

Computer Engineering

Given a good model and implementation of that model, computer simulation can be used to reduce the time and material costs of research. To this end I worked with other students to manufacture, test and simulate the single layer P3HT-PCBM solar cell. Using the data collected from this project, future work can then be done with the project's simulator to further optimize these types of solar cell devices.

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Exercise Power Grid Display And Web Interface, Alexander (Alex) Chernetz

Computer Engineering

The 2008-2009 expansion of the Recreation Center at Cal Poly includes three new rooms with cardiovascular fitness equipment. As part of its ongoing commitment to sustainable development, the new machines connect to the main power grid and generate power during a workout. This document explains the process of quantifying and expressing the power generated using two interfaces: an autonomous display designed for a television with a text size and amount of detail adaptable to multiple television sizes and viewing distances, and an interactive, more detailed Web interface accessible with any Java-capable computer system or browser.