Nanotechnology Fabrication Commons^™

Novel Materials And Devices For Terahertz Detection And Emission For Sensing, Imaging And Communication, Naznin Akter

FIU Electronic Theses and Dissertations

Technical advancement is required to attain a high data transmission rate, which entails expanding beyond the currently available bandwidth and establishing a new standard for the highest data rates, which mandates a higher frequency range and larger bandwidth. The THz spectrum (0.1-10 THz) has been considered as an emerging next frontier for the future 5G and beyond technology. THz frequencies also offer unique characteristics, such as penetrating most dielectric materials like fabric, plastic, and leather, making them appealing for imaging and sensing applications. Therefore, employing a high-power room temperature, tunable THz emitters, and a high responsivity THz detector is essential. …

Multivariate Analysis For The Quantification Of Transdermal Volatile Organic Compounds In Humans By Proton Exchange Membrane Fuel Cell System, Ahmed Hasnain Jalal

FIU Electronic Theses and Dissertations

In this research, a proton exchange membrane fuel cell (PEMFC) sensor was investigated for specific detection of volatile organic compounds (VOCs) for point-of-care (POC) diagnosis of the physiological conditions of humans. A PEMFC is an electrochemical transducer that converts chemical energy into electrical energy. A Redox reaction takes place at its electrodes whereas the volatile biomolecules (e.g. ethanol) are oxidized at the anode and ambient oxygen is reduced at the cathode. The compounds which were the focus of this investigation were ethanol (C₂H₅OH) and isoflurane (C₃H₂ClF₅O), but theoretically, the sensor …

A Novel Reconfiguration Scheme In Quantum-Dot Cellular Automata For Energy Efficient Nanocomputing, Madhusudan Chilakam

Masters Theses 1911 - February 2014

Quantum-Dot Cellular Automata (QCA) is currently being investigated as an alternative to CMOS technology. There has been extensive study on a wide range of circuits from simple logical circuits such as adders to complex circuits such as 4-bit processors. At the same time, little if any work has been done in considering the possibility of reconfiguration to reduce power in QCA devices. This work presents one of the first such efforts when considering reconfigurable QCA architectures which are expected to be both robust and power efficient. We present a new reconfiguration scheme which is highly robust and is expected to …

Parameter Variation Sensing And Estimation In Nanoscale Fabrics, Jianfeng Zhang

Masters Theses 1911 - February 2014

Parameter variations introduced by manufacturing imprecision are becoming more influential on circuit performance. This is especially the case in emerging nanoscale fabrics due to unconventional manufacturing steps (e.g., nano-imprint) and aggressive scaling. These parameter variations can lead to performance deterioration and consequently yield loss.

Parameter variations are typically addressed pre-fabrication with circuit design targeting worst-case timing scenarios. However, this approach is pessimistic and much of performance benefits can be lost. By contrast, if parameter variations can be estimated post-manufacturing, adaptive techniques or reconfiguration could be used to provide more optimal level of tolerance. To estimate parameter variations during run-time, on-chip …

N3asics: Designing Nanofabrics With Fine-Grained Cmos Integration, Pavan Panchapakeshan

Masters Theses 1911 - February 2014

Nanoscale-computing fabrics based on novel materials such as semiconductor nanowires, carbon nanotubes, graphene, etc. have been proposed in recent years. These fabrics employ unconventional manufacturing techniques like Nano-imprint lithography or Super-lattice Nanowire Pattern Transfer to produce ultra-dense nano-structures. However, one key challenge that has received limited attention is the interfacing of unconventional/self-assembly based approaches with conventional CMOS manufacturing to build integrated systems.

We propose a novel nanofabric approach that mixes unconventional nanomanufacturing with CMOS manufacturing flow and design rules to build a reliable nanowire-CMOS 3-D integrated fabric called N³ASICs with no new manufacturing constraints. In N³ASICs …

Towards Logic Functions As The Device Using Spin Wave Functions Nanofabric, Prasad Shabadi

Masters Theses 1911 - February 2014

As CMOS technology scaling is fast approaching its fundamental limits, several new nano-electronic devices have been proposed as possible alternatives to MOSFETs. Research on emerging devices mainly focusses on improving the intrinsic characteristics of these single devices keeping the overall integration approach fairly conventional. However, due to high logic complexity and wiring requirements, the overall system-level power, performance and area do not scale proportional to that of individual devices.

Thereby, we propose a fundamental shift in mindset, to make the devices themselves more functional than simple switches. Our goal in this thesis is to develop a new nanoscale fabric paradigm …