Electronic Devices and Semiconductor Manufacturing Commons^™

Iii-Nitride Nanostructures: Photonics And Memory Device Applications, Barsha Jain

Dissertations

III-nitride materials are extensively studied for various applications. Particularly, III-nitride-based light-emitting diodes (LEDs) have become the major component of the current solid-state lighting (SSL) technology. Current III-nitride-based phosphor-free white color LEDs (White LEDs) require an electron blocking layer (EBL) between the device active region and p-GaN to control the electron overflow from the active region, which has been identified as one of the primary reasons to adversely affect the hole injection process. In this dissertation, the effect of electronically coupled quantum well (QW) is investigated to reduce electron overflow in the InGaN/GaN dot-in-a-wire phosphor-free white LEDs and to improve the …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Machine Learning Approach To Stability Analysis Of Semiconductor Memory Element, Ravindra Thanniru, Gautam Kapila, Nibhrat Lohia

SMU Data Science Review

Memory stability analysis traditionally relied heavily on circuit simulation-based approaches that run Monte Carlo (MC) analysis over various manufacturing and use condition parameters. This paper researches application of Machine Learning approaches for memory element failure analysis which could mimic simulation-like accuracy and minimize the need for engineers to rely heavily on simulators for their validations. Both regressor and classifier algorithms are benchmarked for accuracy and recall scores. A high recall score implies fewer escapes of fails to field and is the metric of choice for comparing algorithm. The paper identifies that recall score in excess of 0.97 can be achieved …

Improving Noise Immunity And Efficiency Using High-Precision Iterative Codes, Sherzod Shukhratovich Atadjanov, Aziza Ahmadjanovna Tursunova

Bulletin of TUIT: Management and Communication Technologies

The article discusses the issues of ensuring noise immunity in digital broadcasting systems, shows the importance of the transition to the optimal code and the need to use it in the field of noiseless coding in various areas of telecommunication transmission and reception of digital signals. The previous algorithms and error-correcting coding methods based on the Gray code, which are used in multi-level digital broadcast modulation schemes to minimize the intensity of bit errors, are highlighted. A model of error-correcting coding by the Gray method and methods for estimating the probability of error for the Gray code are presented. Based …

Printed Circuit Board Design And Layout For Hobbyists, Engineers, And Students, Michael A. Derrenbacher

Master's Theses

Printed Circuit Boards (PCBs) are a ubiquitous element of virtually every electronic system manufactured world-wide. It is not a stretch of the imagination to say that if it’s electronic, there is a PCB in it. PCBs are necessary tools for electronics work, and tools need to have instructions. For better or worse, PCB knowledge is a deep and wide ocean. There is much to cover for even a surface level understanding, and there are deep areas rich in technical expertise. Navigating the ocean of knowledge is treacherous; common knowledge of yore can be downright dubious now. PCB manufacturing and electronics …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Additive Manufacturing Using Robotic Manipulators, Fdm, And Aerosol Jet Printers., Alexander Curry

Electronic Theses and Dissertations

Additive manufacturing has created countless new opportunities for fabrication of devices in the past few years. Advances in additive manufacturing continue to change the way that many devices are fabricated by simplifying processes and often lowering cost. Fused deposition modeling (FDM) is the most common form of 3D printing. It is a well-developed process that can print various plastic materials into three-dimensional structures. This technology is used in a lot of industries for rapid prototyping and sometimes small batch manufacturing. It is very inexpensive, and a prototype can be created in a few hours, rather than days. This is useful …

A Double-Sided Stack Low-Inductance Wire-Bondless Sic Power Module With A Ceramic Interposer, Si Huang

Graduate Theses and Dissertations

The objective of this dissertation research is to develop a novel three-dimensional (3-D) wire bondless power module package for silicon carbide (SiC) power devices to achieve a low parasitic inductance and an improved thermal performance. A half-bridge module consisting of 900-V SiC MOSFETs is realized to minimize stray parasitic inductance as well as to provide both vertical and horizontal cooling paths to maximize heat dissipation. The proposed 3-D power module package was designed, simulated, fabricated and tested. In this module, low temperature co-fired ceramic (LTCC) substrate with vias is utilized as an interposer of which both top and bottom sides …

Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim

Electronic Theses, Projects, and Dissertations

Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

A Compact 1200 V, 700 A, Igbt-Based Pulse Generator For Repetitive Transcranial Magnetic Stimulation In Vivo Laboratory Experiments On Small Animals, Daniel Senda, Haley Strong, Dustin Hines, Rochelle Hines, R. Jacob Baker

Psychology Faculty Research

An insulated-gate bipolar transistor (IGBT) pulse generator for repetitive transcranial magnetic stimulation used for in vivo laboratory experiments on small animals, such as mice, is reported. The pulse generator is based upon an IGBT that can switch 700 A of current for 1 ms and that has a DC breakdown voltage of 1200 V. The duration of the design’s output pulse is controlled by, and follows, an input trigger pulse. The voltage amplitude of the output pulses is determined by an external high-voltage power supply and the energy stored in a 330 µF capacitor bank. The approach enables the amplitude …

Performance Of Calcium Chloride- Ammonia Adsorption Refrigeration System, Michael John

Tanzania Journal of Engineering and Technology (TJET)

An experimental study on the performance of calcium chloride-ammonia adsorption system is described. A single bed water cooled condenser adsorption refrigerator prototype, which utilises calcium chloride-ammonia pair has been developed and tested in the laboratory. Experiments have been conducted for desorption temperatures of 100 °C with desorption time varying from 1 to 4 hours. An electric tape heater and a timer were used to perform the experiments. The adsorption temperature profile, adsorption rate and prototype performance have been analysed and discussed. The tested heating and desorption temperature of 100 °C and heating and desorption time of 1 to 4 hours …

Socio-Technical Perspective For Electronic Tax Information System In Tanzania, Lucas Ngowi, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Socio-technical systems theory has rarely been used by system architects in setting up computing systems. However, the role of socio-technical concepts in computing, which is becoming social in nature, has made the concepts more relevant and commercial. Tax information systems are examples of such systems because they are influenced by external variables such as the political environment, technological trends, and social environment, introducing complexity in their deployment and determining the type of e-services and their delivery to a diverse group of people. It was observed that in Tanzania there is resistance, reluctance and minimal use of electronic tax system because …

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Design And Validation Of A High-Power, High Density All Silicon Carbide Three-Level Inverter, Zhongjing Wang

Graduate Theses and Dissertations

Transportation electrification is clearly the road toward the future. Compared to internal combustion engine, the electrified vehicle has less carbon-dioxide emission, less maintenance costs and less operation costs. It also offers higher efficiency and safety margin. More importantly, it relieves human’s dependence on conventional fossil energy. In the electrification progress, the revolution of electric traction drive systems is one of the most important milestone. The traction system should keep high efficiency to avoid performance reduction. Moreover, the motor drive should be designed within limited space without sacrificing output power rating. Based on the road map from US Drive Electrical and …

On-Chip Nanoscale Plasmonic Optical Modulators, Abdalrahman Mohamed Nader Abdelhamid

Theses and Dissertations

In this thesis work, techniques for downsizing Optical modulators to nanoscale for the purpose of utilization in on chip communication and sensing applications are explored. Nanoscale optical interconnects can solve the electronics speed limiting transmission lines, in addition to decrease the electronic chips heat dissipation. A major obstacle in the path of achieving this goal is to build optical modulators, which transforms data from the electrical form to the optical form, in a size comparable to the size of the electronics components, while also having low insertion loss, high extinction ratio and bandwidth. Also, lap-on-chip applications used for fast diagnostics, …

The Effects Of The Transient And Performance Loss Rates On Pv Output Performance, Chibuisi Chinasaokwu Okorieimoh, Brian Norton, Michael Conlon

Conference papers

Solar photovoltaic (PV) panels experience long-term performance degradation as compared to their initial performance, resulting in lower like-per-like efficiencies and performance ratios. Manufacturers of solar photovoltaic modules normally guarantee a lifespan of more than 20 years. To meet such commitments, it is important to monitor and mitigate PV module degradation during this period, as well as beyond, to recognize maintenance and repair needs. Solar PV modules degrade over time, becoming less effective, less reliable, and eventually unusable. The effects of transient and performance loss rates on the output performance of polycrystalline silicon (p-Si) solar PV modules are the focus of …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Fault Modeling And Test Vector Generation For Asic Devices Exposed To Space Single Event Environment, Ahmed Mohamed

Theses and Dissertations

This work aims at providing a concise automated flow to predict the effect of Single Event Transients (SETs) on ASIC chips by developing a method to characterize the circuit susceptibility to SET pulses propagation and then generation of the required input vectors that sensitize the victim paths. A new enhanced method for SET electrical propagation modeling is proposed and compared to a previously published analytical model. The method was applied on different standard cells libraries built over XFAB Xh018 technology and verified for accuracy against simulations. The new method showed enhancement in accuracy compared with previous work in literature. Industrial …

Autonomous Mortar Remote Control Center, James Tyler Frame

Honors Capstone Projects and Theses

No abstract provided.

Malicious Hardware & Its Effects On Industry, Gustavo Perez

Computer Science and Computer Engineering Undergraduate Honors Theses

In recent years advancements have been made in computer hardware security to circumnavigate the threat of malicious hardware. Threats come in several forms during the development and overall life cycle of computer hardware and I aim to highlight those key points. I will illustrate the various ways in which attackers exploit flaws in a chip design, or how malicious parties take advantage of the many steps required to design and fabricate hardware. Due to these exploits, the industry and consumers have suffered damages in the form of financial loss, physical harm, breaches of personal data, and a multitude of other …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Transimpedance Amplification Of Optocoupler Output For High Temperature Applications, Kara Maurer

Electrical Engineering Undergraduate Honors Theses

When looking to the future of electronics, one characteristic is becoming more lucrative: high temperature capabilities. With the goals of not only becoming more efficient electronically, spatially, and cost-wise, adapting electronics for a high temperature environment can potentially be a route to all three of these goals. Not only does it take away the need for a cooling method, but it can also increase the longevity of a product which can make it even more cost effective. In an effort to contribute to the push for high temperature electronics, the University of Arkansas is developing a high temperature power module …

Optoelectronic Valley-Spin Qubits With Ambipolar Quantum Dots, Jeremy Tull

Electrical Engineering Undergraduate Honors Theses

The current limitations of qubit-based processors are caused by imperfections in quantum gates, leading to a lack of gate fidelity. Gate fidelity can be refined by extending the coherence of qubits and reducing logic operation speed. A potential solution is to develop a hybrid qubit that has the coherence of electrically-controlled quantum dots and the gate speed of their optically-controlled counterparts. Quantum bits that utilize ultrafast optical gating to perform gate operations require precise control of the gating pulse duration. Optical dispersion can cause adverse effects pulse duration, such as pulse broadening, so dispersion-compensation techniques must be employed; by properly …

Effect Of Silicon Carbide On Electric Drivetrains Of Heavy-Duty Vehicles, Haley Solera

Electrical Engineering Undergraduate Honors Theses

The application of electro-mechanical motors in rigorous, high-temperature systems is constantly adapting to suit the growing needs of developers in the automotive, construction, and aerospace industries. With improved efficiency, torque, and environmental impact over conventional internal combustion engines, electric drive trains pose more than ample incentive for manufacturers to invest considerable resources toward the design of newer, better methods of electric propulsion. This paper discusses the motives behind the electrification of heavy-duty vehicles, the state-of-the-art technology currently available on the market, and the novel application of silicon carbide to electric drive trains as a means of increasing their heat tolerance, …

Si-Based Germanium Tin Photodetectors For Infrared Imaging And High-Speed Detection, Huong Tran

Graduate Theses and Dissertations

Infrared (IR) radiation spans the wavelengths of the windows: (1) near-IR region ranging from 0.8 to 1.0 μm, (2) shortwave IR (SWIR) ranging from 1.0 to 3.0 μm, (3) mid-wave IR (MWIR) region covering from 3.0 to 5.0 μm, (4) longwave IR (LWIR) spanning from 8.0 to 12.0 μm, and (5) very longwave IR extending beyond 12.0 μm. The MWIR and LWIR regions are important for night vision in the military, and since the atmosphere does not absorb at these wavelengths, they are also used for free-space communications and astronomy. Automotive and defect detection in the food industry and electronic …

Analysis Of Photodetector Based On Zinc Oxide And Cesium Lead Bromide Heterostructure With Interdigital Metallization, Tanveer Ahmed Siddique

Graduate Theses and Dissertations

In this thesis, photodetector based on the zinc oxide and cesium lead bromide hetero structure were fabricated and characterized. Zinc oxide (ZnO) nanoparticles were synthesized using solution processing and cesium lead bromide (CsPbBr3) thin film was synthesized using two step deposition method. Three phonon modes were obtained by the Raman spectroscopy of ZnO nanoparticles. X-ray diffraction spectra of ZnO exhibits five exciton peaks which denotes that the synthesized ZnO structure was of good crystallinity with wurtzite hexagonal phase. The absorbance spectrum of ZnO shows the bandgap (Eg) in the order of 3.5 eV that aligns with reported results. The photoluminescence …

An Accurate And Efficient Electro-Thermal Compact Model Of Sic Power Mosfet Including Third Quadrant Behavior, Arman Ur Rashid

Graduate Theses and Dissertations

Due to narrower bandgap and lower critical electric field, silicon (Si) power devices have reached their limit in terms of the maximum blocking voltage capability. Exploiting this limitation, wide bandgap devices, namely silicon carbide (SiC) and gallium nitride (GaN) devices, are increasingly encroaching on the lucrative power electronics market. Unlike GaN, SiC devices can exploit most of the established fabrication techniques of Si power devices. Having substrate of the same material, vertical device structures with higher breakdown capabilities are feasible in SiC, unlike their GaN counterpart. Also, the excellent thermal conductivity of SiC, compared to GaN and Si, let SiC …