Electronic Devices and Semiconductor Manufacturing Commons^™

Growth Of Ge Quantum Dots On Si(100)-(2×1) By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled germanium quantum dots (QDs) were grown on Si(100)-(2×1) by pulsed laser deposition. In situ reflection-high energy electron diffraction (RHEED) and postdeposition atomic force microscopy are used to study the growth of the QDs. Several films of different thicknesses were grown at a substrate temperature of 400 °C using a Q-switched Nd:yttrium aluminum garnet laser (λ= 1064 nm, 40 ns pulse width, 23 J/cm ² fluence, and 10 Hz repetition rate). At low film thicknesses, hut clusters that are faceted by different planes, depending on their height, are observed after the completion of the wetting layer. With increasing film thickness, …

Self-Assembly Of Ge Quantum Dots On Si(100)- 2×1 By Pulsed Laser Deposition, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Self-assembled Ge quantum dots are grown on Si(100)- 2×1 by pulsed laser deposition. The growth is studied by in situ reflection high-energy electron diffraction and postdeposition atomic force microscopy. After the completion of the wetting layer, transient hut clusters, faceted by different planes, are observed. When the height of these clusters exceeded a certain value, the facets developed into {305} planes. Some of these huts become {305}-faceted pyramids as the film mean thickness was increased. With further thickness increase, dome clusters developed on the expense of these pyramids. © 2005 American Institute of Physics. [DOI: 10.1063/1.1949285]

Study Of Transport Properties Of Inas Using Monte Carlo Simulation, Satyanadh Gundimada

Electrical & Computer Engineering Theses & Dissertations

The present research is aimed at ascertaining the usefulness of InAs semiconductor material for single photon avalanche photo detectors operating in the Geiger mode at 2 μm wavelengths. InAs is considered as the material suitable for the purpose because of its less bandgap and lower effective mass of the electrons when compared to other semiconductor materials presently in use. Hence, theoretically transient transport properties of bulk InAs are superior and the velocity overshoot phenomena stronger. InAs is a relatively less explored material when compared to other materials like GaAs. The choice of the material is justified with thorough exploration of …

Oxidation-Induced Stacking Fault In (100) And (111) Silicon Wafers, Mei Keat Liang

Student Works (2000-2009)

Oxidation-induced stacking fault (OISF) dimension and density change on (100) and (111) wafers, as a result of repeated preferential etching were studied using AFM. optical microscope and angular polishing techniques. Density on (100) and (111) wafers is independent of surface removal up to 3.0µm. This indicates the single layer nature of OISF formed from the sand blasted wafer. Besides having higher density, OISFs from (100) wafer were longer than OISF from (111) wafer. OISF width increases linearly with surface removal however the length does not change significantly with surface removal. ln the OISF normal depth studies using angular polishing technique, …

Effects Of Argon Dilution Of Silane On The Optical Properties And Surface Morphology Of Hydrogenated Amorphous Silicon, Choon Kheam Lim

Student Works (2000-2009)

Hydrogenated amorphous silicon (a.Si:H) was prepared using the d.c plasma grow discharge system. Two sets of samples were prepared and studied. The first set of samples referred to as the high argon dilution films were prepared from the discharge of pure silane at flow-rate of 5sccm and silane at the same flow-rate diluted in argon at flow-rates of 5, 10 and 15sccm. Similarly, the second set of sample referred to as the low argon dilution films were prepared from the discharge of pure silane at flow-rate of20sccm and silane at the same flow-rate diluted in argon at the flow-rates mentioned …

Theory Of Sic Schottky Barrier Conduction And Model Analysis For Diode Breakdown With And Without Screw Dislocations, Lifeng Zheng

Electrical & Computer Engineering Theses & Dissertations

Silicon Carbide is a very promising candidate for applications in high-power, high-temperature, and high-radiation conditions under which conventional semiconductors cannot perform adequately. However, the SiC processing technology has not yet reached maturity. There is also limited knowledge of its physical and chemical characteristics, and its device behavior is not well understood. The aim of this thesis is to analyze two specific problems in the SiC area. The first issue involves the large discrepancy between experimental I - V characteristics of SiC Schottky diodes and their theoretical values. The observed data, especially at low voltages, is found to be orders of …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Evaluation Of The Transport Properties Of Gasb For Bipolar Applications Through Monte Carlo Simulations, Damayanthi Palaniappan

Electrical & Computer Engineering Theses & Dissertations

GaAs is currently the semiconductor material of choice for high speed, low power applications. Its electronic transport properties are superior to almost all other semiconductors. It is also used in a variety of bipolar applications such as photodetectors and photo-mixers. However, as is well known, the hole mobility and related transport parameters of GaAs are not very good. This is a serious drawback, and poses a potential problem for all applications involving bipolar conductivity. In order to increase the high :frequency limits and high-speed capability of bipolar devices, the choice of an alternative material, therefore, becomes necessary. An important first …

Low-Temperature Molecular Beam Epitaxy Of Gaas: A Theoretical Investigation Of Antisite Incorporation And Reflection High-Energy Diffraction Oscillations, K. Natarajan, Rama Venkat, Donald L. Dorsey

Electrical & Computer Engineering Faculty Research

Surface dynamics dominate the incorporation of charged, As+Ga, and neutral, As0Ga, antisite arsenic, and the temporal variation of reflection high-energy electron diffraction(RHEED) intensity in the low-temperature molecular beam epitaxy of (100) gallium arsenide(GaAs). A rate equation model is proposed which includes the presence and dynamics of a physisorbed arsenic (PA) layer riding the growth surface. The PA layer dictates the incorporation and concentration of As+Ga and As0Ga. Additionally, it influences the RHEED oscillations (ROs) behavior and the RO’s dependence on its coverage through its contribution to the reflected intensity. The model results for the dependence of As+Ga and As0Ga concentrations …

Gallium Desorption Behavior At Algaas/Gaas Heterointerfaces During High-Temperature Molecular Beam Epitaxy, K. Mahalingam, D. L. Dorsey, K. R. Evans, Rama Venkat

Electrical & Computer Engineering Faculty Research

A Monte Carlo simulation study is performed to investigate the Ga desorption behavior during AlGaAs-on-GaAs heterointerface formation by molecular beam epitaxy. The transients in the Ga desorption rate upon opening the Al shutter are shown to be associated with the concurrent reduction in the V/III flux ratio. Monte Carlo simulations employing a constant V/III flux ratio yield a “steplike” variation in the Ga desorption rate with the resulting interfaces closer in abruptness to the ideal AlGaAs-on-GaAs interface. Further details on the stoichiometry of the interface and its relationship with predicted Ga desorption profiles is presented.

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali

Electrical & Computer Engineering Faculty Publications

CuAlSe₂ thin films have been synthesized by chalcogenization of thin Cu and Al layers sequentially deposited by evaporation under vacuum. It is shown that CuAlSe₂ films are obtained with some Cu₂-_δSe and Se phases present at the surface. These surface phases are suppressed by annealing under vacuum and by chemical etching in a KCN solution. At the end of the process, the XRD spectrum demonstrates that textured CuAlSe₂ films have been obtained with preferential orientation of the crystallites along the (112) direction. The gap of the films is 2.7 eV as expected. The …

A Stochastic Model For Crystal-Amorphous Transition In Low Temperature Molecular Beam Epitaxial Si(111), R. Venkatasubramanian, Suresh Gorantla, S. Muthuvenkatraman, Donald L. Dorsey

Electrical & Computer Engineering Faculty Research

Molecular beam epitaxial Si (111) grown below a certain temperature result in amorphous structure due to the limited surface mobility of atoms in finding correct epitaxial sites. In spite of many experimental and theoretical studies, the mechanism of crystal‐amorphous transition and its dynamics related to the growth conditions are not well understood. In this article, we present a theoretical model based on the formation of stacking fault like defects as a precursor to the amorphous transition of the layer. The model is simulated based on a stochastic model approach and the results are compared to that of experiments for temperatures …

Diagnostics Of Cdte Electrodeposition By Rest Potential Voltammetry, Brandon Kemp, Robert Engelken, Arif Raza, Arees Siddiqui, Omer Mustafa

Journal of the Arkansas Academy of Science

Due to the extreme sensitivity of the partial elemental currents (i.e.,iCd, iTe) and, hence, stoichiometry to deposition voltage, temperature, mass transport, and ambient light intensity during electrodeposition of semiconductor films, it is important to implement in-situ methods for monitoring the stoichiometry and related semiconductor efficacy of the growing film. We report investigation of open circuit rest potential (Eoc) voltammetry as one such method during electrodeposition of CdTe from aprotic electrolytes such as ethylene glycol. Plots of transient open circuit potential versus sweep voltage exhibit distinct transition and plateau structures corresponding to Te, CdTe, and Cd phases and correlating with the …

Total Ionizing Dose Effects In Mosfet Devices At 77 K, Kevin J. Daul

Theses and Dissertations

Total ionizing dose effects on thermal oxide and reoxidized nitrided oxide (RNO) MOSFET devices at 77 K were studied. The MOSFETs were immersed in liquid nitrogen and irradiated, using a ⁶⁰Co source, up to 1 Mrad(Si) at a dose rate of 107 rads(Si)-sec. Drain current-gate voltage characteristics were obtained and used to determine threshold voltage and transconductance. At 77 K the subthreshold slopes indicated no observed buildup of interface states in any of the transistors. Furthermore, all transistors experienced very little change in the transconductance. Typical negative shifts in threshold voltage as dose increased were observed in all of …

Model Of A Single Impurity In A Wide Bandgap Semiconductor Describing Electric Field Screening, Anthony N. Dills

Theses and Dissertations

A mathematical model of the influence on electric field screening arising from a single impurity in a wide bandgap semiconductor has been numerically investigated and compared with analytically derived solutions. The parameter set chosen to perform the comparison of analytical solution and numerical solution is based upon a bismuth silicate crystal. Both the analytical calculations and the numerical calculations are an attempt to mathematically model the internal electric field within a semiconductor. Two types of impurities were looked at: a single donor level and a single trap impurity level. In general, after an abrupt application of a voltage across the …

Photoluminescence Spectroscopy Of 4h- And 6h-Sic, William A. Davis

Theses and Dissertations

Typical undoped bulk grown SiC shows n- or p-type conductivity due to residual impurities such as nitrogen, boron, or aluminum. In order to produce high resistivity material, vanadium can be used as a compensating dopant. Since vanadium is an amphoteric dopant in SiC, it produces either a donor state, V_Si⁴⁺(3d¹) → V_Si⁵⁺(3d⁰), or an acceptor state, V_Si⁴⁺(3d¹) → V_Si³⁺(3d²). Thus, vanadium doping can compensate both n- and p-type conductivity. In this work, vanadium doped and undoped 4H- and 6H-SiC grown …

Design, Fabrication, Modeling, And Optical Characterization Of Organic Polymer Nonlinear Directional Couplers, John N. Berry

Theses and Dissertations

This research was an investigation into the suitability of a recently developed polymer, polyphenylene, as a material for integrated optical circuits (IOCs). Polymers show great promise in the area of IOCs because of material processing advantages, compatibility with most existing integrated circuit technology, and relatively strong nonlinear optical characteristics. This thesis contains an overview of: dielectric waveguides, linear and nonlinear directional coupler theory; various models useful in the design and analysis of optical waveguides; the fabrication of three different waveguide designs; the experimental apparatus and procedure used to optically characterize the waveguides; and the experimental results of the characterization. Waveguiding …

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …

Transient Simulations And Modelling Of Semi-Insulating Gaas Photoconductive Switches, Prasun Kumar Raha

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this thesis is to develop a one-dimensional transient simulator for Photoconductive Semiconductor Switches (PCSS) taking into consideration the material characteristics, the internal physical effects, and the external circuit. Simulations have been performed to study the device behavior at different voltage levels for copper-doped silicon-compensated GaAs material, though other materials could easily be simulated by changing the parameters. The model includes hole transport, and the results demonstrate the effect of hole injection, with and without recombination centers. In addition to developing a one-dimensional transient simulator, the role of various physical effects, such as the field-dependence of trapping …

A Novel Technique For Deep Level Characterization Of High-Resistivity Semiconductor Materials, Sridhar Panigrahi

Electrical & Computer Engineering Theses & Dissertations

An improved photo induced current transient spectroscopy (PICTS) technique is developed for studying deep level parameters in high-resistivity semiconductor materials. A new digital data acquisition approach and improvement in the cryogenics of the system have enabled us, for the first time in our laboratory, to detect CuA level in a copper doped silicon compensated gallium arsenide (GaAs:Si:Cu) sample. The digital approach improves both the signal to noise ratio (S/N) and the efficiency of the system. Also, multiple PICTS spectra in a single thermal cycle can be obtained. In the present work, various doped and undoped gallium arsenide ( GaAs) and …

Cathodoluminescence Of Gaas, Tyler Smith

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence of band-gap radiation across the bulk of a proposed semiconductor switch has been studied. Such a device relies on the efficient use of cathodoluminescence to modulate the conductivity of the switch. Diagnostics were configured to measure the intensity of band-gap radiation across the bulk of several switch samples. The measured results were compared to calculations based on a four energy level band-gap model which included two deep levels EL2 and HL10.

Q Improvement Of A 5.2 Ghz Te011 Cavity By Incorporating Y1Ba2Cu3O7-X, R. Joseph Leclear

Electrical & Computer Engineering Theses & Dissertations

Research is undertaken to apply high temperature superconducting material to improve the quality factor (Q) of a 5.2 GHz cylindrical resonant cavity. In particular, the approach is to electrophoretically deposit polycrystalline Y₁Ba₂Cu₃O_7-x (YBCO) on the conducting surface of the cavity cylinder. Spalling of the YBCO ceramic coating due to expansion and contraction of the cavity during sintering and testing is overcome by segmenting the cylinder. Results show that the Q of the cavity is increased over that of a copper cavity at temperatures below 60 K. At 20 K, improvement exceeds a factor …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

Optical And High Electric Field Effects In Bulk Gallium Arsenide Switches, Randy Roush

Electrical & Computer Engineering Theses & Dissertations

During the past few years, bulk, photoconductive switching has become recognized as a viable topic for future research on moderate and high power switches. The two-pulse, or BOSS, concept relies on an excitation laser pulse, and a separate de-excitation pulse in conjunction with silicon doped, copper compensated, GaAs to create a variable temporal electrical pulse width. The research contained in this document provides information concerning the feasibility of the BOSS concept, as the switch is scaled to larger sizes, and higher voltage and current. The major concern will be the high voltage and current effects. The absorption length for 1064 …

Influence Of Copper Doping On The Performance Of Optically Controlled Gaas Switches, St. T. Ko, V. K. Lakdawala, K. H. Schoenbach, M. S. Mazzola

Electrical & Computer Engineering Faculty Publications

The influence of the copper concentration in silicon-doped gallium arsenide on the photoionization and photoquenching of charge carriers was studied both experimentally and theoretically. The studies indicate that the compensation ratio (N_Cu/N_Si) is an important parameter for the GaAs:Si:Cu switch systems with regard to the turn-on and turn-off performance. The optimum copper concentration for the use of GaAs:Si:Cu as an optically controlled closing and opening switch is determined.

Gaas Photoconductive Closing Switches With High Dark Resistance And Microsecond Conductivity Decay, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, R. Germer, G. M. Loubriel, F. J. Zutavern

Electrical & Computer Engineering Faculty Publications

Silicon-doped n-type gallium arsenide crystals, compensated with diffused copper, were studied with respect to their application as photoconductive, high-power closing switches. The attractive features of GaAs:Cu switches are their high dark resistivity, their efficient activation with Nd:YAG laser radiation, and their microsecond conductivity decay time constant. In the authors' experiment, electric fields are high as 19 kV/cm were switched, and current densities of up to 10 kA/cm² were conducted through a closely compensated crystal. At field strengths greater than approximately 10 kV/cm, a voltage `lock-on' effect was observed.

Nanosecond Optical Quenching Of Photoconductivity In A Bulk Gaas Switch, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, S. T. Ko

Electrical & Computer Engineering Faculty Publications

Persistent photoconductivity in copper-compensated, silicon-doped semi-insulating gallium arsenide with a time constant as large as 30 µs has been excited by sub-band-gap laser radiation of photon energy greater than 1 eV. This photoconductivity has been quenched on a nanosecond time scale by laser radiation of photon energy less than 1 eV. The proven ability to turn the switch conductance on and off on command, and to scale the switch to high power could make this semiconductor material the basis of an optically controlled pulsed-power closing and opening switch.

An Optically Controlled Closing And Opening Semiconductor Switch, K. H. Schoenbach, V. K. Lakdawala, R. Germer, S. T. Ko

Electrical & Computer Engineering Faculty Publications

A concept for a bulk semiconductor switch is presented, where the conductivity is increased and reduced, respectively, through illumination with light of different wavelengths. The increase in conductivity is accomplished by electron ionization from deep centers and generation of bound holes. The reduction of conductivity is obtained by hole ionization from the excited centers and subsequent recombination of free electrons and holes. The transient behavior of electron and hole density in a high power semiconductor (GaAs:Cu) switch is computed by means of a rate equation model. Changes in conductivity by five orders of magnitude can be obtained.

A Study Of Thin-Film Superconducting Junctions, William P. Korink

Electrical & Computer Engineering Theses & Dissertations

The information presented in this paper is the result of research conducted toward the development. of a reproducible thin-film superconducting junction. The results of this experimentation and the equipment and procedures used are provided.

A qualitative explanation is given for the theory used in the derivation of the volt-ampere characteristics of thin-film superconducting junctions of metal-insulator- metal construction. This explanation entails the electron flow through the insulating layer through the use of the Fermi-Dirac and density of states functions.

The theoretical investigation is based on the BCS Theory and results in volt-ampere characteristics that agree very well with published experimental …