Electrical and Electronics Commons^™

Surface Acoustic Wave Devices As Chemical Vapor Sensors, Daniel Gallagher

Theses and Dissertations

In order to effectively neutralize non-traditional threats to US forces and population such as improvised explosive devices (IED) and chemical, biological, radio- logical, nuclear, and explosive (CBNRE) weapons, a flexible vapor sensor platform is proposed. This work involves the design, fabrication, and testing of coated surface acoustic wave devices for vapor sensing ability. Devices were fabricated in-house using MEMS fabrication techniques, then coated with a thin layer of a Nafion polymer. The frequency response of coated devices displayed 2 MHz frequency shifts around the resonance frequency upon introduction of ethanol vapors into the nitrogen vapor stream. This indicates strong sensing …

Deep Levels In Gate And Gate:In Crystals Investigated By Deep-Level Transient Spectroscopy And Photoluminescence, Y. Cui, D. D. Caudel, P. Bhattacharya, A. Burger, K. C. Mandal, D. Johnstone, S. A. Payne

Faculty Publications

No abstract provided.

A Novel Discrete Dimming Ballast For Linear Fluorescent Lamps, Haiyan Wang, Ana Vladan Stankovic, Louis Nerone, David Kachmarik

Electrical and Computer Engineering Faculty Publications

A novel discrete dimming ballast for linear fluorescent lamps is proposed in this paper. A proposed dimming control circuit is combined with a ballast module for multiple lamps to realize control of three discrete lighting levels. Compared with conventional step dimming or ON-OFF control methods, the proposed discrete dimming method has the following advantages: 1) digital signal is generated by the dimming control circuit to control the lamps' turn- ON and -OFF, which makes the system more reliable and integrated; 2) the proposed discrete dimming system replaces relays, which are necessary in conventional lamp ON-OFF control, and therefore decreases the …

A Mems Multi-Cantilever Variable Capacitor On Metamaterial, Luke A. Rederus

Theses and Dissertations

Negative refractive index materials are an example of metamaterials that are becoming increasingly popular. Research into these metamaterials could possibly be the first steps toward bending electromagnetic radiation (i.e., microwaves, light, etc.) around an object or person. Split ring resonators (SRR) are classified as metamaterials that create an artificial magnetic response from materials with no inherent magnetic properties. Once fabricated, an SRR has a specific resonant frequency due to its permanent geometry. This research introduces a new concept of using a variable capacitive micro- electro-mechanical system (MEMS) device located at the gap of an SRR to mechanically alter the capacitance …

Power Generation By Harvesting Ambient Energy With A Micro-Electromagnetic Generator, James H. Shields

Theses and Dissertations

This thesis investigated the potential power output of a micro-electromagnetic generator fabricated using typical microfabrication materials and techniques. The design was based on a desire to free bio-implanted or remote electronic devices from batteries and their finite power supplies. A micro-electromagnetic generator could harvest energy from the ambient environment and power such devices indefinitely. Designs for the stator coil and rotor magnet components of the generator were optimized to produce maximum current density based upon electromagnetic theory. The relative orientation of the coil to the rotor and material selection for each component were considered. Coils were fabricated using low-resistance gold. …

A Novel Storage Area Network (San) Extension Solution Over Passive Optical Networks (Pons), Si Yin

Dissertations

After 9/11 and the 2003 power grid failure in North America, storage area network (SAN) extension has emerged as a critical option to ensure business continuity. However, SAN extension encounters challenges in the access network including the scalability, cost, bandwidth bottleneck, and throughput. In this dissertation, a new solution, SAN extension over passive optical networks (S-PONs), has been proposed to address the above problems. PONs are the mainstream wireline technology for upgrading the megabit-level access solutions (such as xDSL and Cable Modem) into gigabit-level broadband access. To tackle the scalability problem and cost challenge, the S-PON architecture has been designed …

Nano-Structured Platforms As A Spectroscopic Tool, Ruiqiong Li

Theses

Nano-structured platforms have been studied for the purpose of enhancing weak fluorescence signals. Each platform was constructed as a thin oxide layer on top of a metal (aluminum) The oxide was perforated with hexagonal array of nano-holes. The pitch of the array was much smaller than the optical wavelengths used. Surface charge waves (Surface Plasmons) could be excited when the platform was oriented at specific direction with respect to the incident optical beam. At this point one can demonstrate that fluorescence signals could be amplified. Since the oxide (alumina) is bio-compatible, one can envision using such platforms in the study …

Tilted Parallel Dielectric Slab As A Multilevel Attenuator For Incident P- Or S-Polarized Light, R. M.A. Azzam

Electrical Engineering Faculty Publications

Under the condition of first-order blooming, a parallel dielectric slab, which is inserted in the path of an obliquely incident p- or s-polarized light beam, introduces multiple discrete attenuation levels given by 1/3, 4/27, 4/243,...... in reflection and 4/9, 4/81, 4/729,...... in transmission. These attenuation levels are independent of the slab refractive index, incident p or s linear polarization, or the presence of identical transparent surface coatings at the front and back sides of the slab. Therefore, the tilted slab provides multidecade reflectance and attenuation reference values that can be used in calibrating spectrophotometers and filters, and also …

Study Of Ingaas Ldmos For Power Conversion Applications, Yidong Liu

Electronic Theses and Dissertations

In this work an n-channel In0.65Ga0.35As LDMOS with Al2O3 as gate dielectric is investigated. Instead of using traditional Si process for LDMOS, we suggest In0.65Ga0.35As as substitute material due to its higher electron mobility and its promising for power applications. The proposed 0.5-µm channel-length LDMOS cell is studied through device TCAD simulation tools. Due to different gate dielectric, comprehensive comparisons between In0.65Ga0.35As LDMOS and Si LDMOS are made in two ways, structure with the same cross-sectional dimension, and structure with different thickness of gate dielectric to achieve the same gate capacitance. The on-resistance of the new device shows a big …

Solar And Fuel Cell Circuit Modeling, Analysis And Integrations With Power Conversion Circuits For Distributed Generation, Smitha Krishnamurthy

Electronic Theses and Dissertations

Renewable energy is considered to be one of the most promising alternatives for the growing energy demand in response to depletion of fossil fuels and undesired global warming issue. With such perspective, Solar Cells and Fuel Cells are most viable, environmentally sound, and sustainable energy sources for power generation. Solar and Fuel cells have created great interests in modern applications including distributed energy generation to provide clean energy. The purpose of this thesis was to perform a detailed analysis and modeling of Solar and Fuel cells using Cadence SPICE, and to investigate dynamic interactions between the modules and power conversion …

Embedded Magnetics For Power System On Chip (Psoc), Jian Lu

Electronic Theses and Dissertations

A novel concept of on-chip bondwire inductors and transformers with ferrite epoxy glob coating is proposed, offering a cost effective approach to realize power systems on chip (PSoC) or System-in-Package (PSiP). The concept has been investigated both experimentally and with finite element modeling. Improvement in total inductance is demonstrated for multi-turn bondwire inductors over single bondwire inductors. The inductance and Q factor can be further boosted with coupled multi-turn inductor concept. Transformer parameters including self- and mutual inductance, and coupling factors are extracted from both modeled and measured S-parameters. More importantly, the bondwire magnetic components can be easily integrated into …

Physical Properties Of Wave Scattering By Chiral Periodic Structure, Xiaomin Yang

Electronic Theses and Dissertations

Attention has been focused on electromagnetic chirality and its potential applications to microwave, millimeter wave and optical wave devices. In this work, wave propagation through a chiral periodic structure with arbitrary shape is investigated. Although perturbation theory and coupled-mode theory have been used to analyze chiral periodic structure, those are approximate methods and can only be used for low frequency applications. In this work, the rigorous mode-matching method is used to solve the problem. Staircase approximation is introduced to change the curved structure to a multilayer structure. The field solutions in the uniform air regions and unbounded air-chiral periodic array …

Reaction Velocities In Free Standing Aluminum And Cooper Oxide This Films, Matthew Erickson

Electronic Theses and Dissertations

In this work we investigate the reaction propagation velocity of aluminum and copper oxide Metastable Intermolecular Composites (MIC's). All samples were deposited in a magnetron sputtering system using 2 aluminum targets and 2 copper targets. The copper is sputtered in an oxygen rich environment in order to obtain copper oxide rich films. Three different layer structures are used for various measurements that are composed of alternating 20 layer pairs, 30 layer pairs, and 40 layer pairs. All layer pairs maintain a constant total thickness of 3.2 microns. Each layer structure can be prepared independent of a substrate and is measured …

Adaptive Efficiency Optimization For Digitally Controlled Dc-Dc Converters, Wisam Al-Hoor

Electronic Theses and Dissertations

The design optimization of DC-DC converters requires the optimum selection of several parameters to achieve improved efficiency and performance. Some of these parameters are load dependent, line dependent, components dependent, and/or temperature dependent. Designing such parameters for a specific load, input and output, components, and temperature may improve single design point efficiency but will not result in maximum efficiency at different conditions, and will not guarantee improvement at that design point because of the components, temperature, and operating point variations. The ability of digital controllers to perform sophisticated algorithms makes it easy to apply adaptive control, where system parameters can …

Unified Large And Small Signal State-Space Based Modeling And Symbolic Simulation For Pwm Converters, Ehab Shoubaki

Electronic Theses and Dissertations

In this Dissertation, which concentrates on discrete modeling for control purposes of DC/DC converters and simulation through symbolic techniques. A Unified Discrete State-Space Model for power converters in CCM is presented. Two main approaches to arriving at the discrete model are used. The first approach involves an impulse function approximation of the duty cycle modulation of the converter switches, and this approach results in a small signal discrete model. The Second approach is direct and does not involve any approximation of the modulation, this approach yields both a large signal nonlinear discrete model and a linear small signal model. Harmonic …

Delay Modeling And Long-Range Predictive Control Of Czochralski Growth Process, Dhaval Shah

Electronic Theses and Dissertations

This work presents the Czochralski growth dynamics as time-varying delay based model, applied to the growth of La3Ga5.5Ta0.5O14 (LGT) piezoelectric crystals. The growth of high-quality large-diameter oxides by Czochralski technique requires the theoretical understanding and optimization of all relevant process parameters, growth conditions, and melts chemistry. Presently, proportional-integral- derivative (PID) type controllers are widely accepted for constant-diameter crystal growth by Czochralski. Such control systems, however, do not account for aspects such as the transportation delay of the heat from crucible wall to the crystal solidification front, heat radiated from the crucible wall above the melt surface, and varying melt level. …

Pulse Frequency Modulation Zcs Flyback Converter In Inverter Applications, Feng Tian

Electronic Theses and Dissertations

Renewable energy source plays an important role in energy co-generation and distribution. A traditional solar-based inverter system has two stages cascaded, which has simpler controller but low efficiency. A new solar-based single-stage grid-connected inverter system can achieve higher efficiency by reducing the power semiconductor switching loss and output stable and synchronizing sinusoid current into the utility grid. In Chapter 1, the characteristic I-V and P-V curve of PV array has been illustrated. Based on prediction of the PV power capacity installed on the grid-connected and off-grid, the trends of grid-tied inverter for DG system have been analyzed. In Chapter 2, …

Efficiency Improvement Techniques For High Voltage Capacitor Charging Methods, Michael Islas

Electronic Theses and Dissertations

The goal of this thesis is to design and fabricate a DC-to-DC converter for use in high-voltage capacitor charging applications. The primary objectives include increasing the efficiency and reducing the cost of traditional methods used for this application. Traditional methods were not designed specifically for high-voltage capacitor charging and were thus very primitive and exhibited lower efficiency. Prior methods made use of a high voltage power supply and a current limiting resistor or control scheme. The power supply would often only operate efficiently at a single voltage value and would thus function poorly over a range used in charging a …

Design And Modeling Of Radiation Hardened Lateral Power Mosfets, Matthew Landowski

Electronic Theses and Dissertations

Galactic-cosmic-rays (GCR) exist in space from unknown origins. A cosmic ray is a very high energy electron, proton, or heavy ion. As a GCR transverses a power semiconductor device, electron-hole-pairs (ehps) are generated along the ion track. Effects from this are referred to as single-event-effects (SEEs). A subset of a SEE is single-event burnout (SEB) which occurs when the parasitic bipolar junction transistor is triggered leading to thermal runaway. The failure mechanism is a complicated mix of photo-generated current, avalanche generated current, and activation of the inherent parasitic bipolar transistor. Current space-borne power systems lack the utility and advantages of …

Simulation Of Brightness Temperatures For The Microwave Radiometer On The Aquarius/Sac-D Mission., Salman Khan

Electronic Theses and Dissertations

Microwave radiometers are highly sensitive receivers capable of measuring low levels of natural blackbody microwave emissions. Remote sensing by satellite microwave radiometers flying on low-earth, polar orbiting, satellites can infer a variety of terrestrial and atmospheric geophysical parameters for scientific and operational applications, such as weather and climate prediction. The objective of this thesis is to provide realistic simulated ocean brightness temperatures for the 3-channel Microwave Radiometer (MWR), which will be launched in May 2010 on the joint NASA/CONAE Aquarius/SAC-D Mission. These data will be used for pre-launch geophysical retrieval algorithms development and validation testing. Analyses are performed to evaluate …

Fabrication And Characterization Of Zirconium Oxide Thin Films, Vemnkata Rama Sesha Ravi Kumar Vemuri

Open Access Theses & Dissertations

Zirconium oxide (ZrO2) is an important material with a potential for a wide range of technological applications. The outstanding chemical stability, electrical and mechanical properties, high dielectric constant, and wide band gap of ZrO2 make it suitable for several industrial applications in the field of optics, electronics, magneto-electronics, and optoelectronics. ZrO2 is frequently used as a high refractive index material in multilayer optical coatings in high power laser systems. ZrO2 is employed in super plastic structural ceramics that demonstrate excellent strength and fracture toughness. ZrO2 has been considered as a promising dielectric to replace SiO2 in advanced metal oxide semiconductor …

Microstructure And Electrical Performance Of Sputter-Deposited Hafnium Oxide (Hfo2) Thin Films, Brandon Adrian Aguirre

Open Access Theses & Dissertations

Hafnium oxide (HfO2) based dielectrics have been currently considered as the possible replacements for the traditional gate-oxide (SiO2) of the complementary metal-oxide semiconductor (CMOS) devices. The high dielectric constant, wide band gap, and thermal stability in contact with Si make HfO2 a potential material for application in CMOS devices. The performance of HfO2 as a gate oxide material, however, depends on its quality and interface structure with Si. In this work, HfO2 thin films have been deposited by rf sputtering onto Si(100) substrates under varying growth temperatures (Ts). The objective of the work is to understand the growth and microstructure …

Directional Analysis And Filtering For Dust Storm Detection In Noaa-Avhrr Imagery, Swapna Janugani

Open Access Theses & Dissertations

In this research, we propose spatio-spectral processing techniques for the detection of dust storms in 5-band NOAA-AVHRR imagery. The research is mainly focused on locating the dust sources and automatically finding the transport direction of the dust storm. Previous methods that use simple band math analysis have produced promising results but have some drawback in producing consistent results when low SNR images are used. Moreover, in seeking to automate the dust storm detection, the presence of clouds in the vicinity of the dust storm creates a challenge in being able to distinguish these two types of image texture. Our research …

Reduced Dimensionality Hyperspectral Classification Using Finite Mixture Models, Vikram Jayaram

Open Access Theses & Dissertations

Classification of HSI data is a challenging problem for two main reasons. First, with limited spatial resolution of HSI sensors and/or the distance of the observed scene, the images invariably contain pixels composed of several materials. It is desirable to resolve the contributions of the constituents from the observed image without relying on high spatial resolution images. Remote sensing cameras have been designed to capture a wide spectral range motivating the use of post-processing techniques to distinguish materials via their spectral signatures. Secondly, available training data for most pattern recognition problems in HSI processing is severely inadequate. Under the framework …

Spatio-Temporal Ecg Analysis For Localization Of Arrhythmias Using Precordial Ecg Leads And 128-Lead Systems, Eduardo Morales

Open Access Theses & Dissertations

A novel and state-of-the-art approach for the analysis of cardiac arrhythmias is proposed. Currently, the analysis of the electrocardiogram is only performed in the time-domain. The proposed method improves the electrocardiogram analysis by adding spatial properties. The spatial properties added to the electrocardiogram allow for the analysis of specific regions inside the human heart where cardiac arrhythmias are suspected to have occurred. In this Dissertation, the concept of electrocardiography was extended using advanced bioelectromagnetism theory. In concrete, the multiple dipole model of the human heart was used to extend the concept of electrocardiography from a temporal analysis to a spatial-temporal …

Smart Heating Systems For Green Homes, Cheryl Carmody

Theses

The focus of this research is to design an improved heating control system for a class of older energy inefficient dwelling to produce an improved living environment. Prerequisites for such control are sensors and models. Commercial sensor nodes enabled a multi-zone heating system to be considered. While the accompanying sensor node software was functional, it was not suitable for real-time control and was modified to achieve same. Once a prototype was developed and tested in the laboratory, it was deployed to a two-story residential dwelling in Cork city.

The requisite mathematical models describe the heat transfer characteristics for a particular …

Monoclinic Optical Constants, Birefringence, And Dichroism Of Slanted Titanium Nanocolumns Determined By Generalized Ellipsometry, Daniel Schmidt, Benjamin Booso, Tino Hofmann, Eva Schubert, Andrew Sarangan, Mathias Schubert

Electrical and Computer Engineering Faculty Publications

Generalized spectroscopic ellipsometry determines the principal monoclinic optical constants of thin films consisting of slanted titanium nanocolumns deposited by glancing angle deposition under 85° incidence and tilted from the surface normal by 47°. Form birefringence measured for wavelengths from 500 to 1000 nm renders the Ti nanocolumns monoclinic absorbing crystals with c-axis along the nanocolumns, b-axis parallel to the film interface, and 67.5° monoclinic angle between the aand c-axes. The columnar thin film reveals anomalous optical dispersion, extreme birefringence, strong dichroism, and differs completely from bulk titanium. Characteristic bulk interband transitions are absent in the spectral range investigated.

A Study Of Cantilever-Free Instrumentation For Nanoscale Magnetic Measurements, Bruce Adair Altemus

Legacy Theses & Dissertations (2009 - 2024)

The evolution of the Atomic Force Microscope (AFM) into the Magnetic Force Microscope (MFM) and Magnetic Resonance Force Microscope (MRFM) has had a substantial impact on the characterization of nanoscale phenomena. Detection of 10-17 Newtons per root Hertz has occurred with use of an ultra-sensitive cantilever along with optical interferometry methods within these geometries. The sensitivity of these platforms is dependent on the characteristics of the cantilever, where increased length and a low Young's modulus increase the force sensitivity (meters/Newtons). Using IC fabrication techniques, the realization of generating cantilevers with this sensitivity is feasible, but stress compensation layers are required …

A Study Of Cantilever-Free Instrumentation For Nanoscale Magnetic Measurements, Bruce Adair Altemus

Legacy Theses & Dissertations (2009 - 2024)

The evolution of the Atomic Force Microscope (AFM) into the Magnetic Force Microscope (MFM) and Magnetic Resonance Force Microscope (MRFM) has had a substantial impact on the characterization of nanoscale phenomena. Detection of 10-17 Newtons per root Hertz has occurred with use of an ultra-sensitive cantilever along with optical interferometry methods within these geometries. The sensitivity of these platforms is dependent on the characteristics of the cantilever, where increased length and a low Young's modulus increase the force sensitivity (meters/Newtons). Using IC fabrication techniques, the realization of generating cantilevers with this sensitivity is feasible, but stress compensation layers are required …

Rf Mems Capacitors For Sdr, Yamuna Kuberappa

Theses

Micro electro mechanical systems (MEMS) applications in radio frequency (RF) and microwave electronics are revolutionizing the progress in wireless communications. In particular, MEMS switchable/tunable capacitors can facilitate the realization of multistandard software defined transceivers, offering better performance than existing solutions.

In this thesis, characterisation and RF modelling of MEMS switchable/tunable capacitors and the technical requirements for their application in multiband wireless transceiver circuits in a software defined radio (SDR) are described. The first device considered is a curled cantilever capacitive switch, configured in both shunt and series configuration where the capacitance is limited to two stable states. The second device, …