Electrical and Electronics Commons^™

Spatio-Temporal Correlation Models For Indoor Mimo Channels, Kaustubha Raghukumar

Theses

Accurate modeling of the spatio-temporal cross-correlation between the subchannels of a multiple-input multiple-output (MIMO) channel is an important prerequisite of multi-element antenna system design. In this thesis, a new model for indoor MIMO channels is proposed, and a closed form expression for the spatio-temporal cross-correlation function is derived. This new analytical correlation expression includes many physical parameters of interest such as the angle-of-arrivals at the base station and the user, the associated angle spreads, and other parameters, in a compact form. Comparison of this model with narrowband indoor MIMO data collected at Brigham Young University exhibits the utility of the …

Characterization And Mapping Of Crystal Defects In Silicon Carbide, Ejiro Emorhokpor

Theses

Silicon carbide (SiC) is a semiconductor with attractive properties, such as a wide bandgap (3. 26 eV), high dielectric strength, and high thermal conductivity that make it suitable for high power, highspeed electronic devices. A major roadblock to its wider application is the presence of defects, particularly micropipes and dislocations, in SiC wafers produced today and decreasing density of these defects is the most important challenge of the industry. The goal of this thesis was to design, build and test a system for detection and analysis of the defects in SiC wafers. The system is based on the reflection optical …

Sparse Matrix Product Implementation On Field Programmable Gate Arrays (Epgas), Amit Mahendra Sheth

Theses

If dense matrix multiplication algorithms are used with sparse matrices, they can result in a large number of redundant calculations, as numerous elements in sparse matrices are zero valued, thus available resources and time may be wasted. The algorithm discussed here aims to take advantage of the sparseness of the matrices by multiplying only nonzero elements.

The NIOS development board from Altera is used for implementing the above algorithm. First a sequential program in the C programming language is downloaded onto the FPGA and run by the NIOS soft-processor. Then the same board is also used for a parallel implementation …

Low-Power Transceiver Design For Mobile Wireless Chemical Biological Sensors, Harshavardhan Reddy Sripuram

Theses

The design of a smart integrated chemical sensor system that will enhance sensor performance and compatibility to Ad hoc network architecture remains a challenge. This work involves the design of a Transceiver for a mobile chemical sensor. The transceiver design integrates all building blocks on-chip, including a low-noise amplifier with an input-matching network, a Voltage Controlled Oscillator with injection locking, Gilbert cell mixers, and a Class E Power amplifier making it as a single-chip transceiver. This proposed low power 2GHz transceiver has been designed in TSMC 0.35~lm CMOS process using Cadence electronic design automation tools. Post layout HSPICE simulation indicates …

Improving The Process Of Laser Retinal Eye Surgery Using Electro Static Micro Mirrors, Narashiman Chakravarthy

Theses

This thesis describes an improved system for laser eye surgery. The system incorporates hardware based image matching and MEMS micromirrors for feedback control of laser positioning on the eye. Many benefits are described in this thesis, such as nulling out eye movement, tracking laser firing history, enabling precise control of laser firing locations and preventing firing accidents. The aim of this work is to frame this improved laser surgery concept and prove the principle of various components of the system. A featured accomplishment is the modeling and simulation of a prototype microcontroller using VHDL that may be incorporated as part …

Firewall Interface For Java Ftp Smtp And Http Servers, Ratan Kumar Erukulla

Theses

The objective of my thesis is to develop a firewall interface for FTP, HTTP and SMTP servers. A firewall interface is a graphical user interface (GUI) to configure the properties of the server. Using this interface, we can spy a user, block and unblock the IP address of a client, display statistics of user and server. We can track all the user actions while he is connected to the server. These actions are logged and based on the log data we can deny access to users performing illegal operations. All the servers and interfaces are written in Java. Java was …

Vlsi Design Of Stability Routing Protocol For Sensors In Wireless Mobile Ad-Hoc Networks, Vishnu M. Mandava

Theses

This thesis gives a detailed description of the Application specific integrated circuit (ASIC) design of Stability routing protocol for sensors in mobile ad-hoc networks. The Stability routing protocol is based on the signal strength and position components during data transmission while considering sensors in an ad-hoc network. A general ad-hoc network has unpredictable and variable mobility patterns therefore the signal strength criteria is adopted for routing. Signal strength criteria has been proved to be efficient for communication between the mobile nodes without any data loss. In this thesis an architecture for a processor implementing stability routing protocol for effective communication …

An Interface Chip For Saw Based Sensor In An Ad-Hoc Network, Yagneshwara Ramakrishna Vadapalli

Theses

The design of a smart integrated chemical sensor system that will enhance sensor performance and compatibility to ad hoc network architecture remains a challenge. This work involves the design of an interface chip for a Surface Acoustic Wave (SAW) based chemical sensor where the sensor reflects the RF input and introduces a time delay proportional to the concentration of the vapors absorbed by it. The interface chip detects the frequency shift as a function of the chemical species absorbed by the sensor and alerts the ad hoc network controller when a monitored parameter exceeded some threshold, based on local processing …

Design For Signal Integrity In High Frequency, High Density Circuit Boards, Juan Manuel Talavera Martinez

Theses

The electronics market is continually seeking fast and small high performance products. The clock frequency in computer systems is often above 2GHz and new generations of laptops have considerably reduced in size. These features make printed circuit board (PCB) design more difficult than in the past.

This thesis is an investigation of the current design of high speed PCB. The complexity of this type of circuit makes the designer needs an extensive knowledge of the techniques used to generate a reliable signalling, in other words, signal integrity. To achieve this objective, the design community has to overcome several problem related …

Automated Distribution And Management Of Software And Hardware Configurations For Heterogeneous Wireless Devices, Grainne Foley

Theses

The continuing evolution of wireless networks and services has increased the complexity and diversity of wireless networks and devices, placing significant emphasis on the need for flexible device configuration management. Widely varying wireless technologies currently operate independently worldwide, making global wireless network access for the mobile user confusing and unwieldy. New technologies, network access methodologies and improved services further obscure the evolving environment. The focus of effort for this thesis is the development of a system to automate the distribution and management of software and hardware configurations that enable different levels of wireless device reconfiguration. The scope of investigation will …

Dynamically Biased Radio Frequency Power Amplifier, Tom Twomey

Theses

With the current trend in mobile communications towards more complex modulation schemes to enhance spectral efficiency, the design of RF power amplifiers is the subject of considerable interest and research. The newer more spectrally efficient modulation schemes require a much higher level of linearity due to the non-constant level of their signal envelope. A variable envelope signal would in non-linear amplifiers lead to unacceptable levels of distortion. Linear amplifiers solve this problem at the cost of significant loss of efficiency. With the evolution towards more spectrally efficient modulation schemes, the trade off between linearity and power efficiency has become more …

Performance Evaluation Of Sip Based Services In Umts, Maria Isabel Pous Fenollar

Theses

With ever increasing penetration of IP technologies and the tremendous growth in wireless data traffic, the wireless industry is evolving the mobile core networks towards IP technology. The 3rd Generation Partnership Project (3GPP) is specifying an IP Multimedia Core Network Sub-System (IMS) in UMTS Release 5 and Release 6, which is adjunct to the UMTS GPRS core network. This IP-based network will allow mobile operators to provide commonly used Internet applications to wireless user. The UMTS IMS uses the Internet Engineering Task Force (IETF) defined text based Session Initiation Protocol (SIP), to control a wide range of anticipated IP-based services …

Adaptive Baseband Predistortion For Rf Power Amplifier Linearization., Laura Faus-Ferrer

Theses

In order to make use of spectrally efficient linear modulation methods for mobile communications, it is necessary to linearise the underlying RF power amplifier (PA). A number of techniques for linearizing a PA have been studied, focusing on the Adaptive Baseband Predistortion. The work is centred on the research concentrates on the analysis of different algorithms, their simulation using MatLab, and implementation of a predistorter as a subsystem of a prototype Cartesian based transmitter.

The thesis describes the typical architecture of a transceiver with an emphasis on the nonlinear analysis. Cavers’ algorithm has been examined in terms of its computational …

Modern Control Techniques For Induction Machines In High-Performance Adjustable-Speed Drives, Pat Cronin

Theses

Induction Motors (IM’s) are increasingly being considered for and used in high-performance motor drive (HPMD) systems. Their application has only gained acceptance since the 1970’s with the advent of vector control, microprocessors and improvements in power converter technology. D.C. motors were traditionally the preferred choice in HPMD systems. The main reasons for IM acceptance in HPMD systems are ruggedness, durability, low maintenance, cost, and small size by comparison with D.C. motors.

Alternating current asynchronous motors of the IM type are considered to be the universal workhorses of the manufacturing industry. It has been estimated that they are used in seventy …

Multiple Model Control With Intelligent Switching To Ensure Robustness To Process Variations., Peter Cunningham

Theses

One of the most popular approaches for dealing with process that undergo large variations with time, of late, is the multiple model approach. This method has considerable intuitive appeal and has received widespread dissemination in academia. Numerous successful simulations have been reported although few real-time results have been published. The principal contribution of this thesis is the application of the multiple model control scheme in real-time.

A number of practical concepts that enable the use of multiple model control in real-time are discussed. Many of these issues arose when the multiple model control scheme was applied to a laboratory scale …

Hot Carrier Reliability Of Lateral Dmos Transistors In Power Process Applications, Vicky O'Donovan

Theses

The purpose of this study is to investigate and validate the mechanism of hot carrier degradation of the LDMOS device. The LDMOS device is a new technology to Analog Devices, and a relatively new topic to the semiconductor industry, evident from the limited published research in the field. A prerequisite for device release on a product in the market place, is comprehensive hot carrier reliability testing, as hot carrier degradation has evolved as one of the foremost concerns in submicron devices. Both the high voltage and the structural difference of the LDMOS device, from standard MOSFET device, pose a hot …

On Chip Implement Of Deadlock Avoidance In Wormhole Networks, Kiran K. Gururaj

Theses

This thesis gives a detailed description of the Application Specific Integrated Circuit (ASIC) design to avoid deadlocks in Wormhole Networks. Deadlock avoidance is the most critical issue while considering wormhole networks and should be avoided by any routing protocol and algorithm. A novel architecture for the Turn Prohibition Based Routing (TPBR) protocol has been proved to be efficient and was developed as a part of this work. This architecture for implementing the algorithm is divided into three parts. The first part determines the order of selccuon of the nodes, in the network to run the algorithm. The second part deals …

Stereo Matching Algorithm By Propagation Of Correspondences And Stereo Vision Instrumentation, Peerajak Witoonchart

Theses

A new image processing method is described for measuring the 3-D coordinates of a complex, biological surface. One of the problems in stereo vision is known as the accuracy-precision tradeoff problem. This thesis proposes a new method that promises to solve this problem. To do so, two issues are addressed. First, stereo vision instrumentation methods are described. This instrumentation includes a camera system as well as camera calibration, rectification, matching and triangulation. Second, the approach employs an array of cameras that allow accurate computation of the depth map of a surface by propagation of correspondences through pair-wise camera views.

The …

Recent Advances In Silicon Light Emitting Diodes, Aravind Balakrishnan

Theses

A silicon based light emitting diode (LED) is a new gateway for combining optoelectronics with CMOS integrated circuits. The choice of silicon is limited due to its indirect band gap nature. There are new approaches for improving emission efficiencies in Si-LED to nearly 1% at room temperature. Boron implantation has been employed to introduce dislocation array and as a p-type dopant to form p-n Junction in an n-type Si substrate. The device operates as a conventional LED under forward bias. The temperature dependence of radiative recombination rate is addressed by Varshni empirical formula. The difference between the energy at which …

Determination Of Phase Composition Of Sputtered Tantalum On Steel Substrates By Resistivity Measurements, Younes Abbassi

Theses

The objective of this thesis was to develop a method of distinguishing between alpha and beta phases of tantalum films on steel substrates, using the four-point probe resistivity measurements. While there is a large difference between resistivities of the two Ta phases, the problem is challenging because the measurements are influenced by the low resistivity of steel.

For reference, the resistivity measurements of tantalum coatings (1-20 μm) on silicon and silicon dioxide substrates were conducted first. The measured resistivities were related to the crystallographic phase composition of Ta, which has lower resistivity in bcc form, α-phase, (13.5 to 42 μΩcm), …

Hyperbolic Position Location Estimator With Tdoas From Four Stations, Sreeram Potluri

Theses

This thesis presents a detailed derivation of a set of equations needed to locate the three dimensional position of a mobile given the locations of four fixed stations (like a global positioning system (GPS) satellite or a base station in a cell) and the signal time of arrival (TOA) from the mobile to each station. From these derived equations, a synthesizable VHDL model was developed and simulated using IEEE numen*c_std package. All the inputs and outputs were described by 32 bit vectors. From the simulations, it was observed that in the best case the mobile position was off by I …

Qos Routing Source Routing Problems And Solutions, Ye Tian

Theses

The notion of Quality-of-Service has been proposed to capture qualitatively or quantitatively defined performance contracts between the service provider and the user applications. Integrated network services are designed to support Quality-of-Service (QoS). One of the primary goals for the integrated network services is to find the paths that satisfy given QoS requirements, namely QoS routing. The challenging issue in this area is to route packets subjected to multiple uncorrelated constraints because the problem is inherently NP-complete. This thesis studies the source routing heuristic approaches that bring the time complexity down to the polynomial-time for the multi-constrained path (MCP) problem. A …

Extensible Data Storage And Presentation Technology For An Ophthalmology Electronic Patient Record, Markus H. Heinrichs

Theses

The Electronic Patient Record (EPR) is a central element of practice systems used in ophthalmology. It acts as a repository for multi-media patient care data as well as billing information, serving healthcare providers and ultimately their patients. The aim of this thesis is to create both a data structure and a flexible on-screen representation of an EPR for an ophthalmology practice, and to provide an XML-based experimental prototype as a “proof of concept” which could ultimately be used as an replacement for an existing DOS- based solution. The medical background and requirements for this system will be described. The state-of-the-art …

Design And Analysis Of Radio Frequency Deployment Algorithms For Gsm, Mónica Pérez-Carbonell

Theses

Due to the growth of the subscriber base and the introduction of new services, mobile communications networks’ demand for wireless resources is increasing. This has resulted in an increasing need to change the frequency allocation of a network in order to adapt the cellular network to new frequency demands.

Currently, a planning tool generates a new frequency plan, which is. then deployed to cell sites. The deployment should ideally be carried out with minimum disruption to network operation, which makes this deployment process a critical undertaking as any errors during or after the deployment can leave the network with poor …

Robust Generalised Predictive Control - An Optimal Design For Uncertain Systems, Thomas O'Mahony

Theses

One of the more popular model predictive control approaches, of late, is the generalised predictive controller (GPC). It has received widespread dissemination in academia and numerous successful applications in industry testify to its usefulness. Its popularity partly stems from its superiority over its predecessors, its simplicity and its control acumen. However, since GPC is based on a mathematical model of the process, significant deterioration in performance or even closed-loop instability may arise due to the inevitable discrepancies that arise between the model and the true system. To ensure that the loop stability is not compromised and an adequate level of …

Servo Response And Modelling Issues In Generalised Predictive Control, Ben Griffin

Theses

One of the more popular control strategies, of late, is the Generalised Predictive Controller (GPC). It has received widespread dissemination in academia and numerous successful applications in industry testify to its usefulness. Its popularity partly stems from its superiority to its predecessors, e.g. the generalised minimum variance and pole-placement controllers, but also from the GPC ‘tuning knobs’, which have simple time-domain interpretations and extremely robust default settings. However, despite the widespread interest, there would appear to be some issues relating to the specification of the closed-loop serv^o response that have not been covered in any great detail in the GPC …

Design Of Low Phase Drift Cmos Frequency Synthesisers, Cyril Patrick Hervé Florent Lahuec

Theses

This thesis presents a methodology for the development of high performance video clock synthesisers that have high (2000) input to output clock multiplication ratios. The synthesisers are required to be compatible with standard CMOS technologies and they must exhibit very low drift between their input and output clocks.

The methodology used borrows techniques established for RF synthesisers in the GHz range. In the RF domain there are significant constraints on spectral spread and because of this there has been significant interest in phase noise generated by intrinsic device noise. Simple and accurate models were developed that help understand the up …

Optical Properties Of Photonic Crystals, Anand G. Shenoy

Theses

The ability to confine light in three dimensions has important implications for quantum optics and quantum-optical devices. Photonic crystals, the optical analog of electronic crystals, provide us a means of achieving this goal. This analogy has motivated a whole new series of experimental and theoretical searches for elusive photonic band-gap structures. Combinations of metallic and dielectric materials can be used to obtain the required three-dimensional (3D) periodic variation in the dielectric constant. This could pave the way for photonic crystal structures that have widespread applications.

The working of 3D photonic crystals into the wavelength regimes where most optoelectronic devices operate, …

Propagation And Scattering Of Collimated Beam Wave In Vegetation Using Scalar Transport Theory, Michael Yu-Chi Wu

Theses

The scalar time-dependent equation of radiative transfer is used to develop a theory of pulse beamwave propagation and scattering in a medium character ized by many random discrete scatterers which scatter energy strongly in the forward scattering direction. Applications include the scattering of highly collimated millimeter waves in vegetation and optical beams in the atmosphere. The specific problem analyzed is that of a periodic sequence of Gaussian shaped pulses normally incident from free space onto the planar boundary surface of a random medium half-space, such as a forest, that possesses a power scatter (phase) function consisting of a strong, narrow …

A Study And Some Experimental Work Of Digital Image And Video Watermarking, Tsui-Feng Liu

Theses

The rapid growth of digitized media and the emergence of digital networks have created a pressing need for copyright protection and anonymous communications schemes. Digital watermarking (or data hiding in a more general term) is a kind of steganography technique by adding information into a digital data stream. Several most important watermarking schemes applied to multilevel and binary still images and digital videos were studied. They include schemes based on DCT (Discrete Cosine Transform), DWT (Discrete Wavelet Transform), and fractal transforms. The question whether these invisible watermarking techniques can resolve the issue of rightful ownership of intellectual properties was discussed. …