Electrical and Electronics Commons^™

Accurate Location Of Evolving Faults On Transmission Lines Using Sparse Wide Area Measurements, Xiangqing Jiao, Yuan Liao

Electrical and Computer Engineering Faculty Publications

In electric power systems, not all fault conditions remain unchanged during faults. An evolving fault has one characteristic initially and changes to a different condition subsequently. Locating evolving faults is challenging due to the change in fault type shortly after the fault initiation. This paper presents a new approach for estimating the locations of evolving faults on transmission lines. By using sparse wide area voltage measurements, this method is able to accurately locate evolving faults without requiring measurements from either end of the faulted line. There is no need to detect whether a fault is an evolving fault or not. …

Assessing The Spatial Accuracy And Precision Of Lidar For Remote Sensing In Agriculture, Surya Saket Dasika

Theses and Dissertations--Biosystems and Agricultural Engineering

The objective of this whole study was to evaluate a LiDAR sensor for high-resolution remote sensing in agriculture. A linear motion system was developed to precisely control the dynamics of LiDAR sensor in effort to remove uncertainty in the LiDAR position/velocity while under motion. A user control interface was developed to operate the system under different velocity profiles and log LiDAR data synchronous to the motion of the system. The LiDAR was then validated using multiple test targets with five different velocity profiles to determine the effect of sensor velocity and height above a target on measurement error. The results …

Contributions To Hybrid Power Systems Incorporating Renewables For Desalination Systems, Nasser Alawhali

Theses and Dissertations--Electrical and Computer Engineering

Renewable energy is one of the most reliable resource that can be used to generate the electricity. It is expected to be the most highly used resource for electricity generation in many countries in the world in the next few decades. Renewable energy resources can be used in several purposes. It can be used for electricity generation, water desalination and mining. Using renewable resources to desalinate the water has several advantages such as reduce the emission, save money and improve the public health. The research described in the thesis focuses on the analysis of using the renewable resources such as …

Real-Time Image Pattern Sensor For Weld Pool Penetration Through Reflection In Gtaw, Yu-Ting Chen

Theses and Dissertations--Electrical and Computer Engineering

In gas tungsten arc welding (GTAW), weld pool surface contains crucial information for welding development. In this research, simulate skilled welders to control the welding process and determine the penetration stages based on the weld pool reaction.

This study focuses on solving the uncertainty of the liquid weld pool in joint bases. The weld pool penetration process is highly depending on how the weld pool surface shape. To observe the weld pool, reflect the weld pool surface by the laser and image on the shield glass. The experiments show that the penetration can’t be determine by the reflecting grayness due …

Design Of A Machine Vision Camera For Spatial Augmented Reality, Matt Phillip Ruffner

Theses and Dissertations--Electrical and Computer Engineering

Structured Light Imaging (SLI) is a means of digital reconstruction, or Three-Dimensional (3D) scanning, and has uses that span many disciplines. A projector, camera and Personal Computer (PC) are required to perform such 3D scans. Slight variances in synchronization between these three devices can cause malfunctions in the process due to the limitations of PC graphics processors as real-time systems. Previous work used a Field Programmable Gate Array (FPGA) to both drive the projector and trigger the camera, eliminating these timing issues, but still needing an external camera. This thesis proposes the incorporation of the camera with the FPGA SLI …

Stability Analysis And Design Of A Tracking Filter For Variable Frequency Applications, Pranav Aramane

Theses and Dissertations--Electrical and Computer Engineering

The work presented in this thesis is a frequency adaptive tracking filter that can be used in exact tracking of power frequencies and rejection of unwanted harmonics introduced during power disturbances. The power synchronization process includes power converters and other equipment that have many non-linear components that introduce unwanted harmonics. This new design is motivated by the requirement of a filter that can filter all the harmonics and exactly track a rapidly varying fundamental frequency with little time delay and phase error. This thesis analyzes the proposed filter mathematically based on Lyapunov theory and simulations are presented to show the …

Fabrication And Characterization Of Organic-Inorganic Hybrid Perovskite Solar Cells, Hojjatollah Sarvari

Theses and Dissertations--Electrical and Computer Engineering

Solar energy as the most abundant source of energy is clean, non-pollutant, and completely renewable, which provides energy security, independence, and reliability. Organic-inorganic hybrid perovskite solar cells (PSCs) revolutionized the photovoltaics field not only by showing high efficiency of above 22% in just a few years but also by providing cheap and facile fabrication methods.

In this dissertation, fabrication of PSCs in both ambient air conditions and environmentally controlled N₂-filled glove-box are studied. Several characterization methods such as SEM, XRD, EDS, Profilometry, four-point probe measurement, EQE, and current-voltage measurements were employed to examine the quality of thin films …

Advanced Synchronous Machine Modeling, Yuqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

The synchronous machine is one of the critical components of electric power systems. Modeling of synchronous machines is essential for power systems analyses. Electric machines are often interfaced with power electronic components. This work presents an advanced synchronous machine modeling, which emphasis on the modeling and simulation of systems that contain a mixture of synchronous machines and power electronic components. Such systems can be found in electric drive systems, dc power systems, renewable energy, and conventional synchronous machine excitation. Numerous models and formulations have been used to study synchronous machines in different applications. Herein, a unified derivation of the various …

Ionic Thermoelectric Paper, Fei Jiao, Ali Naderi, Dan Zhao, Joshua Schlueter, Maryam Shahi, Jonas Sundström, Hjalmar Granberg, Jesper Edberg, Ujwala Ail, Joseph W. Brill, Tom Lindström, Magnus Berggren, Xavier Crispin

Physics and Astronomy Faculty Publications

Ionic thermoelectric materials, for example, polyelectrolytes such as polystyrene sulfonate sodium (PSSNa), constitute a new class of materials which are attracting interest because of their large Seebeck coefficient and the possibility that they could be used in ionic thermoelectric SCs (ITESCs) and field effect transistors. However, pure polyelectrolyte membranes are not robust or flexible. In this paper, the preparation of ionic thermoelectric paper using a simple, scalable and cost-effective method is described. After a composite was fabricated with nanofibrillated cellulose (NFC), the resulting NFC–PSSNa paper is flexible and mechanically robust, which is desirable if it is to be used in …

Field-Induced Formation And Growth Of Pillars On Films Of Bisphenol-A-Polycarbonate, Yu-Fan Chuang, Jyun-Siang Peng, Fuqian Yang, Donyau Chiang, Sanboh Lee

Chemical and Materials Engineering Faculty Publications

An electric field is used to construct pillars on films of bisphenol-A-polycarbonate (BPAPC) between two parallel electrodes. Both the size and density of the pillars are dependent on the film thickness. For the same experimental conditions, thicker films will lead to the formation of pillars of larger sizes and smaller densities. The time dependence of the average diameter of the pillars is found to be a linear function of the square root of the difference between the annealing time and incubation time. The temperature dependence of the temporal evolution of the pillars follows the Arrhenius relation with an activation enthalpy …

Improvements In Inverter Modeling And Control, Xiao Liu

Theses and Dissertations--Electrical and Computer Engineering

In this dissertation, the generalized averaging method models for inverters, reactive power control methods for photovoltaic inverters, and a noise immunity improvement for hybrid position observers for brushless dc motor drives are studied.

Models of inverters and other converters based on averaging have been widely used in numerous simulation applications. Generalized averaging can be applied to model both average and switching behavior of converters while retaining the faster run times associated with average-value models. Herein, generalized average models for single- and three-phase pulse width modulation inverters are proposed. The modulation signal for the proposed model could be either a sinusoidal …

Enhanced Metallic Properties Of Srruo3 Thin Films Via Kinetically Controlled Pulsed Laser Epitaxy, Justin K. Thompson, J. Nichols, S. Lee, S. Ryee, John H. Gruenewald, John G. Connell, Maryam Souri, J. M. Johnson, J. Hwang, M. J. Han, H. N. Lee, D. -W. Kim, Sung S. Ambrose Seo

Physics and Astronomy Faculty Publications

Metal electrodes are a universal element of all electronic devices. Conducting SrRuO₃ (SRO) epitaxial thin films have been extensively used as electrodes in complex-oxide heterostructures due to good lattice mismatches with perovskite substrates. However, when compared to SRO single crystals, SRO thin films have shown reduced conductivity and Curie temperatures (T_C), which can lead to higher Joule heating and energy loss in the devices. Here, we report that high-quality SRO thin films can be synthesized by controlling the plume dynamics and growth rate of pulsed laser epitaxy (PLE) with real-time optical spectroscopic monitoring. The SRO thin …

Hallmarks Of The Mott-Metal Crossover In The Hole-Doped Pseudospin-1/2 Mott Insulator Sr2Iro4, Yue Cao, Qiang Wang, Justin A. Waugh, Theodore J. Reber, Haoxiang Li, Xiaoqing Zhou, Stephen Parham, S. -R. Park, Nicholas C. Plumb, Eli Rotenberg, Aaron Bostwick, Jonathan D. Denlinger, Tongfei Qi, Michael A. Hermele, Gang Cao, Daniel S. Dessau

Physics and Astronomy Faculty Publications

The physics of doped Mott insulators remains controversial after decades of active research, hindered by the interplay among competing orders and fluctuations. It is thus highly desired to distinguish the intrinsic characters of the Mott-metal crossover from those of other origins. Here we investigate the evolution of electronic structure and dynamics of the hole-doped pseudospin-1/2 Mott insulator Sr₂IrO₄. The effective hole doping is achieved by replacing Ir with Rh atoms, with the chemical potential immediately jumping to or near the top of the lower Hubbard band. The doped iridates exhibit multiple iconic low-energy features previously observed …

Electron Beam Induced Deposition Of Highly Conductive Copper Nanowires From Bulk Liquids, Amjad M. Syam

Theses and Dissertations--Electrical and Computer Engineering

Electron-beam induced deposition (EBID) is a position-controlled technique that can directly fabricate nanometer-sized structures in functional materials. In the standard process, a gaseous precursor delivers the desired substance to the substrate for deposition. However, the material purity from these precursors is typically poor, which often negatively affects the functional properties of the deposit. Recently, bulk liquid precursors have been investigated as promising reactants for high purity deposition without the need for post-processing. In this work, EBID from bulk liquids is shown to yield highly conductive nanowire deposits. Aqueous solutions containing copper sulfate (CuSO₄) and sulfuric acid (H_{2 …}

A Lithium Battery Current Estimation Technique Using An Unknown Input Observer, Daniel Cambron

Theses and Dissertations--Electrical and Computer Engineering

Current consumption measurements are useful in a wide variety of applications, including power monitoring and fault detection within a lithium battery management system (BMS). This measurement is typically taken using either a shunt resistor or a Hall-effect current transducer. Although both methods have achieved accurate current measurements, shunt resistors have inherent power loss and often require isolation circuitry, and Hall-effect sensors are generally expensive. This work explores a novel alternative to sensing battery current by measuring terminal voltages and cell temperatures and using an unknown input observer (UIO) to estimate the battery current. An accurate model of a LiFePO_{4 …}

Modelling Of The Nanowire Cds-Cdte Device Design For Enhanced Quantum Efficiency In Window-Absorber Type Solar Cells, Rasika Ganvir

Theses and Dissertations--Electrical and Computer Engineering

Numerical simulations of current-voltage characteristics of nanowire CdS/CdTe solar cells are performed as a function of temperature using SCAPS-1D. This research compares the experimental current-voltage (I-V) characteristics with the numerical (I-V) simulations obtained from SCAPS-1D at various temperatures. Various device parameters were studied which can affect the efficiency of the nanowire-CdS/CdTe solar cell. It was observed that the present simulated model explains the important effects of these solar cell devices, such as the crossover and the rollover effect. It was shown that the removal of defect in i-SnO2 is responsible for producing the crossover effect. In the past, the rollover …

A Modular Electrical Power System Architecture For Small Spacecraft, Timothy M. Lim

Theses and Dissertations--Electrical and Computer Engineering

Small satellites and CubeSats have established themselves within the aerospace community because of their low cost and high return on investment. Many CubeSats are developed in a short time frame and often leverage commercial off the shelf components for quick turnaround missions. With regard to the Electrical Power System, commercially available products typically use a centralized architecture. However, a centralized architecture is not reusable, since missions that require additional solar arrays or batteries would necessitate a redesign of the power system. With the range of CubeSat sizes and mission goals, it is obvious that a one-size-fits-all solution is not appropriate. …

Per-Pixel Calibration For Rgb-Depth Natural 3d Reconstruction On Gpu, Sen Li

Theses and Dissertations--Electrical and Computer Engineering

Ever since the Kinect brought low-cost depth cameras into consumer market, great interest has been invigorated into Red-Green-Blue-Depth (RGBD) sensors. Without calibration, a RGBD camera’s horizontal and vertical field of view (FoV) could help generate 3D reconstruction in camera space naturally on graphics processing unit (GPU), which however is badly deformed by the lens distortions and imperfect depth resolution (depth distortion). The camera’s calibration based on a pinhole-camera model and a high-order distortion removal model requires a lot of calculations in the fragment shader. In order to get rid of both the lens distortion and the depth distortion …

Genetic Algorithms In Stochastic Optimization And Applications In Power Electronics, Mengmei Liu

Theses and Dissertations--Electrical and Computer Engineering

Genetic Algorithms (GAs) are widely used in multiple fields, ranging from mathematics, physics, to engineering fields, computational science, bioinformatics, manufacturing, economics, etc. The stochastic optimization problems are important in power electronics and control systems, and most designs require choosing optimum parameters to ensure maximum control effect or minimum noise impact; however, they are difficult to solve using the exhaustive searching method, especially when the search domain conveys a large area or is infinite. Instead, GAs can be applied to solve those problems. And efficient computing budget allocation technique for allocating the samples in GAs is necessary because the real-life problems …

Small Satellite Noncommutative Rotation Sequence Attitude Control Using Piezoelectric Actuators, Joshua L. Evans

Theses and Dissertations--Electrical and Computer Engineering

Attitude control remains one of the top engineering challenges faced by small satellite mission planning and design. Conventional methods for attitude control include propulsion, reaction wheels, magnetic torque coils, and passive stabilization mechanisms, such as permanent magnets that align with planetary magnetic fields. Drawbacks of these conventional attitude control methods for small satellites include size, power consumption, dependence on external magnetic fields, and lack of full control authority. This research investigates an alternative, novel approach to attitude-control method for small satellites, utilizing the noncommutative property of rigid body rotation sequences. Piezoelectric bimorph actuators are used to induce sinusoidal small-amplitude satellite …

An Organic Mixed Ion-Electron Conductor For Power Electronics, Abdellah Malti, Jesper Edberg, Hjalmar Granberg, Zia Ullah Khan, Jens W. Andreasen, Xianjie Liu, Dan Zhao, Hao Zhang, Yulong Yao, Joseph W. Brill, Isak Engquist, Mats Fahlman, Lars Wågberg, Xavier Crispin, Magnus Berggren

Physics and Astronomy Faculty Publications

A mixed ionic–electronic conductor based on nanofibrillated cellulose composited with poly(3,4-ethylene-dioxythio­phene):­poly(styrene-sulfonate) along with high boiling point solvents is demonstrated in bulky electrochemical devices. The high electronic and ionic conductivities of the resulting nanopaper are exploited in devices which exhibit record values for the charge storage capacitance (1F) in supercapacitors and transconductance (1S) in electrochemical transistors.

Electron-Beam Patterning Of Teflon Af For Surface Plasmon Resonance Sensing, Mansoor A. Sultan

Theses and Dissertations--Electrical and Computer Engineering

Variable pressure electron beam etching and lithography for Teflon AF has been demonstrated. The relation between dose and etching depth is tested under high vacuum and water vapor. High resolution structures as small as 75 nm half-pitch have been resolved. Several simulation tools were tested for surface plasmon excitation. Grating based dual mode surface plasmon excitation has been shown numerically and experimentally.

Control System Development And Response Analysis Of An Electronically Actuated Variable-Orifice Nozzle For Agricultural Pesticide Applications, Joe D. Luck, Scott A. Shearer, Michael P. Sama, Santosh K. Pitla

Biosystems and Agricultural Engineering Faculty Publications

The goal of this research project was to further the development of an electromechanically controlled variable-orifice nozzle by creating an electronic control system and then evaluating that system based on step and ramp inputs. The control system was developed in a programming environment that combined an electronic data acquisition system and actuator with pressure and flow sensors. A proportional, variable-gain (based on system pressure) control system was developed to adjust nozzle flow rates to meet target application rates. The constraints were to achieve settling time of less than 1.0 s, overshoot of less than 10% of maximum flow (or minimum …

Fault Section Identification For Power Distribution Systems Using Online Measurements, Jie Chen

Theses and Dissertations--Electrical and Computer Engineering

Fault location is very important for distribution systems, and quickly identifying the fault and restoring the system can help reduce the outage time and make the system more reliable. In this thesis, a method for locating faults on distribution systems is introduced to quickly identify the faulted feeder sections by using the overcurrent information from the switches in the system. Fuzzy logic is utilized. The proposed method can quickly and accurately locate faulted sections with different fault locations, fault types and fault resistances. The method is applicable to cases with single-faults or multi-faults, and is applicable to networks with multi-sources. …

Nanostructured Semiconductor Device Design In Solar Cells, Hongmei Dang

Theses and Dissertations--Electrical and Computer Engineering

We demonstrate the use of embedded CdS nanowires in improving spectral transmission loss and the low mechanical and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide spectrum range provides an evidence for improving light transmission in the window layer and enhancing absorption and carrier generation in absorber. Nanowire CdS/CdTe solar cells with Cu/graphite/silver paste as back contacts, on SnO₂/ITO-soda lime glass substrates, yield the …

Explorations For Efficient Reversible Barrel Shifters And Their Mappings In Qca Nanocomputing, Ke Chen

Theses and Dissertations--Electrical and Computer Engineering

This thesis is based on promising computing paradigm of reversible logic which generates unique outputs out of the inputs and. Reversible logic circuits maintain one-to-one mapping inside of the inputs and the outputs. Compared to the traditional irreversible computation, reversible logic circuit has the advantage that it successfully avoids the information loss during computations. Also, reversible logic is useful to design ultra-low-power nanocomputing circuits, circuits for quantum computing, and the nanocircuits that are testable in nature. Reversible computing circuits require the ancilla inputs and the garbage outputs. Ancilla input is the constant input in reversible circuits. Garbage output is the …

Multifrequency Averaging Of Hysteresis-Current-Controlled Dc-Dc Converters, Yingying Liu

Theses and Dissertations--Electrical and Computer Engineering

Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior as well as the ripple behavior of power electronic systems. Hysteresis current control has fast response and internal current stability through controlling switches to maintain the current within a given hysteresis band of a given current command. However the state space variables in a hysteresis controlled system cannot be directly approached by multifrequency averaging method because of time varing switching frequency. In this thesis, a method of applying multifrequency …

Average-Value Modeling Of Hysteresis Current Control In Power Electronics, Hanling Chen

Theses and Dissertations--Electrical and Computer Engineering

Hysteresis current control has been widely used in power electronics with the advantages of fast dynamic response under parameter, line and load variation and ensured stability. However, a main disadvantage of hysteresis current control is the uncertain and varying switching frequency which makes it difficult to form an average-value model. The changing switching frequency and unspecified switching duty cycle make conventional average-value models based on PWM control difficult to apply directly to converters that are controlled by hysteresis current control.

In this work, a new method for average-value modeling of hysteresis current control in boost converters, three-phase inverters, and brushless …

Active Current Injection Method For Limiting Ground Fault Current Harmonics In Underground Coal Mines, Yigong Zhang

Theses and Dissertations--Mining Engineering

Current practice in U.S. underground coal mine high-voltage distribution systems is to attempt to limit ground fault current to 25 Amperes and de-energize the circuit at 10 Amperes. However, the significant amount of system capacitance due to the use of shielded cables can cause ground fault current to be two or three times the intended ground fault limit. Consequently, this practice can cause several issues such as ground fault currents significantly exceeding the neutral grounding resistor current limit, loss of relay selectivity in the distribution system, and transient overvoltages in certain ground fault situations. These issues are solved to some …

Model Analysis And Predictive Control Of Double Electrode Submerged Arc Welding Process For Fillet Joints With Root Opening, Yi Lu

Theses and Dissertations--Electrical and Computer Engineering

Submerged Arc Welding (SAW) for fillet joints is one of the major applications in the shipbuilding industry. Due to the requirement for the weld size, a sufficient amount of metal must be deposited. In conventional SAW process, the heat input is proportional to the amount of metal melted and is thus determined by the required weld size. To meet this requirement, an excessive amount of heat is applied causing large distortions on the welded structures whose follow-up straightening is highly costly. In order to reduce the needed heat input, Double-Electrode (DE) technology has been practiced creating the Double-Electrode SAW (DE-SAW) …