Electrical and Electronics Commons^™

Rfid Techniques For Passive Electronics, Ryan Behr, David Cobos

Electrical Engineering

No abstract provided.

Smooth Ternary Signaling For Deep-Submicron(Dsm) Buses, Robert Endicott Hanson, Ryan Ian Fullerton

Electrical Engineering

This project demonstrates the error mitigating effects of using a three-level “smooth ternary” signal on a Deep-Submicron(DSM) bus with large inter-wire capacitance. An RC circuit used to simulate and exaggerate (for easier testing) the charging and discharging of the DSM bus. An encoder stage translates binary input data into a three-level signal before sending it to the bus. A decoder stage then translates the three-level signal back to binary that is ideally identical to the original signal. Our results show that the three-level signal has much cleaner transitions than a traditional binary signal. A few glitches that appeared when decoding …

Design And Simulation Of V2g Bidirectional Inverter And Dc-Dc Converter, Allan Agatep, Mason Ung

Electrical Engineering

As plug-in hybrid electric vehicles (PHEV) become more popular, the utility companies are forced to feed the grid more electricity. However, these PHEVs are capable of providing power to the grid when they are parked serving as ancillary systems for grid regulation (V2G). Using a system based on photovoltaic (PV) technology, a design for a bidirectional inverter with LCL filter, and a bidirectional dc-dc with a constant current controller, was constructed using LTspice. Various papers were researched and analyzed to determine applicable designs for components. Simulations show the designs are capable of bidirectional power transfer. ETAP simulations show that delivering …

Variability Of Electroluminescent Displays, Christopher (C.) Michael Shedd, Nathan Ostrout

Graphic Communication

No abstract provided.

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

Elliptical Machine Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Greg Hollister

Electrical Engineering

Designing a DC/DC Converter for the Cal Poly Energy Harvesting from Exercise Machines project requires special attention to the unique operating characteristics of the source and the load. An elliptical machine powered by a person exercising comprises the source, while an AC Inverter makes up the load. This project attempts to integrate the two devices with a custom DC/DC Converter in order to ultimately deliver power back into the power grid.

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Led Spotlight, Eric Toussaint

Electrical Engineering

This report details the development and construction of an LED spotlight useable in a theatrical or architectural setting.  In depth background information, initial design concepts, lighting instrument specifications, assembly, testing, and conclusions from results are highlighted in this document.  Project goals include efforts to support more energy efficient lighting in the arts and general lighting applications and a decrease in overall costs for energy used in all dramatic and architectural lighting applications.

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process.  In addition, some applications of UEP are incorporated into the official releases of the device product.  UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD).  This thesis covers the flexible and reusable …

Electric Guitar Amplifier With Digital Effects, Shawn Garrett

Computer Engineering

During the course of this project, the research and development of an electric guitar amplifier was undertaken. This amplifier is divided into three distinct sections. The power distribution circuitry provides the proper voltages to safely operate all necessary components. The DSP and digital effects stage provides processing and allows the user to add digital effects to the original guitar sound. The amplification stage increases the power of the input signal to drive a loudspeaker. Due to several setbacks throughout the course of this project, the overall amplifier was not completed. All three of the sections were developed to working functionality, …

Aether, Thomas Cameron, Kristine Colton, Daren Childers

Electrical Engineering

Aether is a RC-style autonomous air vehicle that utilizes GPS positioning along with a wireless communication system to achieve a computer-controlled flight.

This report will incorporate the acquisition, design, integration, implementation and testing phases of the UAV development. Furthermore a discussion of troubleshooting as well as improvements for future projects will be included.

Wireless Energy Transfer, Ryan Sasur

Electrical Engineering

Phones are now an integral component in the daily lives of people. Smartphones give access to movies, internet, and even books. This versatility and increased use can also lead to a shorter battery life. A phone with video viewing capabilities will be a heavy load on the unit’s battery. With phones utilizing 3G and 4G technology, even heavier demands are placed on the battery. As technology improves even further to provide for a larger entertainment experience on the phone, this could also lead to further battery degradation if the current battery situation isn’t addressed. To have a fully operational phone …

Hydro-Electric Generation System For The Dc House Project, Dennis Kwan, Mitchell Krug

Electrical Engineering

This paper focuses on the design, integration, and construction of a system that harnesses energy from flowing water. The system will be used in conjunction with the DC House Project. The proposed system employs a DC generator and DC-DC Boost-converter to provide electricity to the DC House at approximately 200-300W. Results of the testing and measurement show that the goal of the system is feasible, but currently limited. The generator could not output the specified power. Details of the design, along with ideas for further improvement, are presented in this report.

Auto Dialer Wireless Smoke Detector/Alarm System, Manny Linhares

Electrical Engineering

Smoke Detectors/Alarms save the lives of over sixty percent of people each year in the United States. Most of the existing homes are still fitted with the normal smoke detectors either running out of the 120V ac wiring or out of a 9V dc battery. These alarms are perfectly fine to alert residents if there is a fire while they are home. But for people who are away from home when a fire occurs, it would be nice if they could be alerted automatically of such an occurrence and therefore be able to act upon the event by either calling …

Class-F Power Amplifier With Maximized Pae, Kai Shing Tsang

Master's Theses

Due to the rapid development of telecommunication devices, operating speeds are getting faster and more power is being consumed by those devices. Therefore, there is a big concern on how to prolong the battery life in order to fit consumers’ needs. Power amplifiers (PA) at the front end of wireless equipment have drawn a big concern from engineers because of their large power consumption in the system. There is a lot research conducted on PA solutions for improving power-added efficiency (PAE) of amplifiers. PAE is a figure of merit representing how efficient the PA converts DC power to RF power. …

Enhanced Cal Poly Super System Simulink Model, Matthew Ogden Mcfarland

Master's Theses

The Cal Poly Sustainable Power for Electrical Resources (SuPER) project is a solar power DC distribution system designed to autonomously manage and supply the energy needs of a single family off-the-grid home. The following thesis describes the improvement and re-design of a MATLAB Simulink model for the Cal Poly SuPER system. This model includes a photovoltaic (PV) array, a lead-acid gel battery with temperature effects, a wind turbine model, a re-designed DC-DC converter, a DC microgrid, and multiple loads. This thesis will also include several control algorithms such as a temperature controlled thermoelectric (T.E.) cooler, intelligent load switching, and an …

Asynchronous Mips Processors: Educational Simulations, Robert L. Webb

Master's Theses

The system clock has been omnipresent in most mainstream chip designs. While simplifying many design problems the clock has caused the problems of clock skew, high power consumption, electromagnetic interference, and worst-case performance. In recent years, as the timing constraints of synchronous designs have been squeezed ever tighter, the efficiencies of asynchronous designs have become more attractive. By removing the clock, these issues can be mitigated. How- ever, asynchronous designs are generally more complex and difficult to debug. In this paper I discuss the advantages of asynchronous processors and the specifics of some asynchronous designs, outline the roadblocks to asynchronous …

Irrigation Leak Detection: Using Flow Rate Sensors To Detect Breaks In An Irrigation System, Adam Openshaw, Kalvin Vu

Computer Engineering

This report details the exploration and invention of a mechanism that can detect breaks in an irrigation system. With the ultimate goal of conserving water, we have designed an inexpensive, self sustaining flow rate monitor that can be used to identify anomalies in an irrigation system and wirelessly communicate the status of the system to a base station. Our implementation can also determine the direction of the anomaly based on the nature of the anomaly itself. This means that multiple monitors can be used to pinpoint the location of a break within the system in addition to merely detecting its …

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Analog Electric Guitar Distortion Effects And Headphone Amplification, Michael Alexander Jenkins

Electrical Engineering

The goal of this project was to create an electronic system which integrates popular audio processing effects as well as headphone amplification circuitry for use with an electric guitar. By implementing a system which fits natively inside the body of an electric guitar, the need for numerous external accessories relating to a standalone amplifier system is eliminated, improving device versatility and portability.

Single-Ended Tube-Based Guitar Amplifier, Joseph (Joe) Linn

Electrical Engineering

Since the advent of the transistor, the vast majority of designers and manufacturers of electronic devices have abandoned the vacuum tube. Compared to transistors, tubes are orders of magnitude larger, more power hungry, more expensive, less reliable, and dissipate much more heat. In short, transistors are superior devices for almost all applications. Despite this fact, many makers of high-end audio and instrument amplifiers continue to base their designs on tube technology.

Given all of their shortcomings, the obvious question is: Why bother with tubes? Proponents of tube-based audio amplifiers cite a certain “warmth” that tube circuitry lends to the sound …

Modular Laser Combat System For Remotely Operated Vehicles: Bridging The Gap Between Computer Simulation And Live Fire, Thomas Edward Fulenwider

Master's Theses

In the emerging industry of small unmanned vehicles, pioneered by small businesses and research institutions, a suitable combat system test platform is needed. Computer simulations are useful, but do not provide the definitive proof of effective operation necessary for deployment of a combat system. What is needed is an affordable simulated weapons system that enables live flight testing without the used of live weaponry.

A framework is developed here for the construction of a simulated weapon using Free Space Optical (FSO) infrared communication. It is developed in such a way to ensure compatibility with a variety of platforms including ground …

Polyenvi, Stephen Beard, Josh Engel, Paul Fake, Diego Flores, Alvaro Nunez, Miguel Wong

Electrical Engineering

Poor indoor air quality is a problem that is recognized by the Environmental Protection Agency (EPA) to cause health issues. In order to raise awareness of this problem, this document outlines the construction of a device that economically measures air quality through five metrics: dust, smoke, ozone, humidity, and temperature. The device integrates with a router to provide users access to information about their indoor air quality anywhere over the internet as well as local access to the data via an LCD mounted on the router. By increasing indoor air quality awareness, this device will aid users in making adjustments …

Electric Bicycle System, Robert Cong, Rodney Martinez, Mark Casilang, Peter Vong

Electrical Engineering

The Electric Bicycle System is a systems project that incorporates three different ways of charging a lithium-ion battery: the 120VAC wall outlet, regenerative braking, and solar power; which is used to power an electric hub motor running a bicycle. The purpose of the project is to show that it is possible and relatively simple, to build an electric bicycle by oneself. This project can be broken down into five separate categories: the lithium-ion battery, the DC-DC boost converter, the solar panel, the motor, and the motor controller. Each of these will be built upon and improved further by future students, …

Class-D Power Amplifier, Joseph Maldonado, Jeovany Vega

Electrical Engineering

No abstract provided.

Systems Engineering Analysis And Digital Communication Bus Design For The Cal Poly Super Project, Matt Marcus Camack

Master's Theses

With an expected lifetime of 20 years and an expected cost of $500, the Cal Poly Sustainable Power for Electrical Resources (SuPER) project needed a strong central design. This thesis looks at the work completed by students over the previous 5 years, with an eye on the future, to create the phase 2 design. Part of this new structure focuses on a distributed communication bus for monitoring system health and status. Instead of complex and costly computer or FPGA systems, the new system will run solely with microcontrollers. This reduces costs and will hopefully still be used within 5, 10, …