Controls and Control Theory Commons^™

On The Use Of Lorawan For Smart Fishing Applications In The Blue Economy Sector, Eva Shayo

Tanzania Journal of Engineering and Technology (TJET)

The growth of digital technology is expected to transform small-scale fishery sectors, where a need for robust, low-cost, long-range communication networks becomes critical. There exist several technologies that are used in the fishery sector but they are never affordable to small scale fisheries. This study evaluates the feasibility of using low cost Long Range Wide Area Network (LoRaWAN) technology specifically tailored for smart fishing environments to small scale fishery sector. Using simulation, we assess the performance of the key performance metrics including probability of success and energy efficiency under varying device densities and time. During evaluation, we considered end devices …

Analysis And Design Of A 2-Bit Millimeter-Wave Reconfigurable Intelligent Surface And Investigation Of Fss-Assisted Angular Stability, Max Spalek

Master's Theses

Millimeter-Wave (mm-wave) technology utilizes high frequency spectrum and can deliver multi-gigabit speeds, ultra-low latency, and massive bandwidth capacity. However, this technology is rather new and many technical challenges remain. On the other hand, Reconfigurable Intelligent Surfaces (RIS) have emerged as promising structures for controllable electromagnetic wavefront manipulation in wireless communication systems. This thesis presents the design of a 2-bit RIS unit-cell element operating throughout the 30–34 GHz mm-wave band, where the structure was progressively refined from an initial resonating geometry toward a grounded reflective RIS configuration. The proposed structure utilizes PIN-diode switching states to produce four discrete reflected phase states …

Investigation Of The Electrical Capacitance Tomography System For Determining The Spatial Distribution Of Moisture In Grain Storage, Shamte J. Kawambwa

Tanzania Journal of Engineering and Technology (TJET)

Excessive moisture content (MC) in stored grains promotes the growth of fungi and molds, which affects the quality of the grains. Effective grain monitoring methods are essential for detecting and managing grain spoilage. Electromagnetic imaging (EMI) techniques provide a promising alternative to traditional techniques by visualizing the spatial distribution of moisture within grains rather than merely average MC values offered by traditional techniques. However, existing EMI approaches often use hard-field waves, which are expensive and fragile. This study introduces an Electrical Capacitance Tomography (ECT) system that employs soft-field waves to monitor the moisture content of the grains. The system was …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Smart System For Wheat Diseases Early Detection, Rustam Baratov, Himola Sunnatillayeva, Almardon Mamatovich Mustafoqulov

Chemical Technology, Control and Management

This paper presents a smart system for early detection of wheat plant diseases in the vegetation period. The proposed smart system allows detecting three types of wheat diseases, particularly yellow rust, powdery mildew and septoria at early stage and significantly improves the soil and ecology by locally spraying harmful chemicals just to sickness plants. The proposed diagnostic program is created in the C++ programming language. The basic structure of the smart system consists of Raspberry PI 4 MODULE, Logitech HD Pro Webcam C920, buzzer, HC-SR04 distance sensor, DC motor driver, AC motor, power supply, relay and some digital devices.

Improving Cellphone-Based Bio-Imaging Technique For Fluorescence Detection, Erteza T. Efaz

LSU Master's Theses

The research presented in this thesis focuses on the design, development, and evaluation of a fluorescence detection system. The system is implemented primarily as an Android application, Auto Camera, which leverages smartphone cameras to capture and analyze fluorescent images. The application provides a user-friendly interface with some configurable features like exposure time, ISO speed, and storage limit; as well as defining detection thresholds and setting acquisition intervals. This study begins with the architectural framework of the Android application, which is written in Java using Android Studio. The API compatibility is set to version 33, and users are prompted to grant …

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

Machine Learning Approach For Classifying Power Outage In Secondary Electric Distribution Network, Stephan Mgaya, Hellen Maziku

Tanzania Journal of Engineering and Technology (TJET)

Power outage is the problem that hinders social and economic development especially for developing countries like Tanzania. Frequent power outages damage electric equipment, and negatively affect the industrial production process. Power outages cannot be completely eradicated due to uncontrolled cause like natural calamities but technical challenges can be managed and hence reducing power outages. The existing manual methods used to locate power outage like customer calls is inefficient and time consuming. On the other hand, modern method like the Advanced Metering Infrastructure (AMI) still faces a challenge in effectively classifying power line outage due to the nature of imbalanced datasets. …

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …

Real-Time Complex Hand Gestures Recognition Based On Multi- Dimensional Features, Isack Bulugu

Tanzania Journal of Engineering and Technology (TJET)

Gesture recognition is broadly utilized within the field of sensing. There are basically three gesture recognition methods based on computer vision, depth sensor and motion sensor. Motion sensor-based gesture recognition has few input data, fast speed, and direct access to three- dimensional information of the hand. The advantages of traditional motion sensor-based gesture recognition have gradually become a current research hotspot. The essence of traditional motion sensor-based gesture recognition is a pattern recognition problem, and its accuracy depends heavily on the feature dataset extracted from prior experience. Unlike traditional pattern recognition methods, deep learning can be used to a large …

Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim

Electronic Theses, Projects, and Dissertations

Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …

Socio-Technical Perspective For Electronic Tax Information System In Tanzania, Lucas Ngowi, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Socio-technical systems theory has rarely been used by system architects in setting up computing systems. However, the role of socio-technical concepts in computing, which is becoming social in nature, has made the concepts more relevant and commercial. Tax information systems are examples of such systems because they are influenced by external variables such as the political environment, technological trends, and social environment, introducing complexity in their deployment and determining the type of e-services and their delivery to a diverse group of people. It was observed that in Tanzania there is resistance, reluctance and minimal use of electronic tax system because …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

An Exploratory Study Of Pulse Width And Delta Sigma Modulators, Logan B. Penrod

Master's Theses

This paper explores the noise shaping and noise producing qualities of Delta-Sigma Modulators (DSM) and Pulse-Width Modulators (PWM). DSM has long been dominant in the Delta Sigma Analog-to-Digital Converter (DSADC) as a noise-shaped quantizer and time discretizer, while PWM, with a similar self oscillating structure, has seen use in Class D Power Amplifiers, performing a similar function. It has been shown that the PWM in Class D Amplifiers outperforms the DSM [1], but could this advantage be used in DSADC use-cases? LTSpice simulation and printed circuit board implementation and test are used to present data on four variations of these …

Reducing Emi In Sic Direct Torque Controlled Motor Drive, Michael Sykes

Electrical Engineering Undergraduate Honors Theses

This paper covers the comparison between Silicon (Si) vs Silicon Carbide (SiC) for Motor Drive systems and a possible control algorithm to limit the increased Electromagnetic Interference (EMI) caused by using SiC transistors for the inverter. Motor Drive systems need constant improvements if the world is going to move on from machines that emit CO₂ and other harmful gases into the Earth’s atmosphere. One reason these electric machines are not commonplace today is because of their efficiency and other problems they may cause. Silicon transistors are the most commonplace transistor around the world today, but advances over the past …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Design And Analysis Of Modular Axial Flux Switched Reluctance Motor, Rochak Shiwakoti

LSU New Orleans Theses and Dissertations

This thesis presents a new modular structure of the axial flux Switched Reluctance Motor (SRM). The design consists of four stator disks with each adjacent disk rotated 30 degrees apart and four rotor disks connected to a common shaft. The proposed design aims to reduce the unwanted radial force, mitigate the torque ripple, and improve the efficiency. The modular structure distributes the radial force and torque strokes along the axial length of the motor, potentially damping the torque pulsation. In addition, the modular structure would deliver the rating power at a lower current level, reducing the overall ohmic loss. Moreover, …

Challenges In Flexible Microsystem Manufacturing : Fabrication, Robotic Assembly, Control, And Packaging., Danming Wei

Electronic Theses and Dissertations

Microsystems have been investigated with renewed interest for the last three decades because of the emerging development of microelectromechanical system (MEMS) technology and the advancement of nanotechnology. The applications of microrobots and distributed sensors have the potential to revolutionize micro and nano manufacturing and have other important health applications for drug delivery and minimal invasive surgery. A class of microrobots studied in this thesis, such as the Solid Articulated Four Axis Microrobot (sAFAM) are driven by MEMS actuators, transmissions, and end-effectors realized by 3-Dimensional MEMS assembly. Another class of microrobots studied here, like those competing in the annual IEEE Mobile …

Application Of Modular Multilevel Converters (Mmc) Using Phase-Shifted Pwm And Selective Harmonic Elimination In Distribution Systems, Thouhidul Islam

Graduate Theses and Dissertations

Reducing the size and weight of a power electric system is a prodigious challenge to researchers as the development of the latest technologies emerge in the field of electrical engineering. A similar urge is there to develop a light-weight mobile power substation (MPS) to use in the electric power distribution systems during emergency conditions. This thesis proposes a power electronics based solution using the modular multilevel converter (MMC) topology to design the MPS system. The market-available power semiconductor devices are analyzed and suitable devices are selected to design the system. The phase-shifted pulse width modulation (PS-PWM) and selective harmonic elimination …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

An Exact Analysis For Four-Order Acousto-Optic Bragg Diffraction Which Incorporates Both Incident Light Angle And Sound Frequency Dependencies, Adeyinka Sunday Ademola

Electrical Engineering Theses

This thesis extends the prior work which produced an exact solution to the four-order acousto-optic (AO) Bragg cell with assumed fixed center frequency and with exact Bragg angle incident light. The extension predicts the model that incorporates the dependencies of both the input angle of light and the sound frequency. Specifically, a generalized 4^th order linear differential equation (DE), is developed from a simultaneous analysis of four coupled AO system of DEs. Through standard methods, the characteristic roots, which requires solving a quartic equation, is produced. Subsequently, a derived system of homogeneous solutions, which absorbs the roots obtained using …

Analysis And Simulation Of Photovoltaic Systems Incorporating Battery Energy Storage, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

Solar energy is an abundant renewable source, which is expected to play an increasing role in the grid's future infrastructure for distributed generation. The research described in the thesis focuses on the analysis of integrating multi-megawatt photovoltaics (PV) systems with battery energy storage into the existing grid and on the theory supporting the electrical operation of components and systems. The PV system is divided into several sections, each having its own DC-DC converter for maximum power point tracking and a two-level grid connected inverter with different control strategies. The functions of the battery are explored by connecting it to the …

Out-Of-Loop Compensation Method For Op-Amps Driving Heavy Capacitive Loads, Shubham Gandhi

Master's Theses

It is well known that real op-amps do not share most of the desirable characteristics of an ideal one, particularly those of gain and output impedance. When presented with a capacitive load, such as a MOSFET or ADC, feedback in an op-amp circuit can quickly become unstable. This thesis studies and characterizes an op-amp’s output impedance and how its interaction with this type of load creates a parasitic pole which leads to instability. Applying ideas from feedback control theory, a model for studying the problem is developed from which a generalized method for compensating the undesirable circumstance is formulated.

Even …

Phase Locked Loop Integrated Circuit, Scott Buchanan, Jonathan Bonello

Electrical Engineering

No abstract provided.

Measurement And Modeling Of Humidity Sensors, Jingbo Tong

Theses and Dissertations--Electrical and Computer Engineering

Humidity measurement has been increasingly important in many industries and process control applications. This thesis research focus mainly on humidity sensor calibration and characterization. The humidity sensor instrumentation is briefly described. The testing infrastructure was designed for sensor data acquisition, in order to compensate the humidity sensor’s temperature coefficient, temperature chambers using Peltier elements are used to achieve easy-controllable stable temperatures. The sensor characterization falls into a multivariate interpolation problem. Neuron networks is tried for non-linear data fitting, but in the circumstance of limited training data, an innovative algorithm was developed to utilize shape preserving polynomials in multiple planes in …

Understanding Vehicular Traffic Behavior From Video: A Survey Of Unsupervised Approaches, Brendan Tran Morris, Mohan Manubhai Trivedi

Electrical & Computer Engineering Faculty Research

Recent emerging trends for automatic behavior analysis and understanding from infrastructure video are reviewed. Research has shifted from high-resolution estimation of vehicle state and instead, pushed machine learning approaches to extract meaningful patterns in aggregates in an unsupervised fashion. These patterns represent priors on observable motion, which can be utilized to describe a scene, answer behavior questions such as where is a vehicle going, how many vehicles are performing the same action, and to detect an abnormal event. The review focuses on two main methods for scene description, trajectory clustering and topic modeling. Example applications that utilize the behavioral modeling …

Wireless Sensor Networks And The Internet Of Things, Yingtao Jiang, Lei Zhang, Ling Wang

Electrical & Computer Engineering Faculty Research

It is estimated that mobile internet devices that can act as sensors will outnumber humans this year (2013), and by 2015, there will be about 15 billion internet-connected devices. Related applications are thriving in commercial, civic, and scientific operations that involve sensors, web, and services, leading by both academic societies and industry companies. It is commonly accepted that the next generation of internet is becoming the “Internet of Things (IoT)” which is a worldwide network of interconnected objects and their virtual representations uniquely addressable based on standard communication protocols. Identified by a unique address, any object including computers, mobile phones, …